Airworthiness Directives; Fokker Model F27 Series Airplanes (Excluding Mark 050 Series Airplanes)

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 60 › 60 FR 332

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 93-NM-229-AD; Amendment 39-9103; AD 94-26-08]

Airworthiness Directives; Fokker Model F27 Series Airplanes

(Excluding Mark 050 Series Airplanes)

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),

applicable to certain Fokker Model F27 series airplanes, that requires

accomplishment of certain structural modifications. This amendment is

prompted by reports of incidents involving fatigue cracking and

corrosion in transport category airplanes that are approaching or have

exceeded their economic design goal. These incidents have jeopardized

the airworthiness of the affected airplanes. The actions specified by

this AD are intended to prevent degradation in the structural

capabilities of the affected airplanes. This action also reflects the

FAA's decision that long term continued operational safety should be

assured by actual modification of the airframe rather than repetitive

inspections.

DATES: Effective February 3, 1995.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of February 3, 1995.

ADDRESSES: The service information referenced in this AD may be

obtained from Fokker Aircraft USA, Inc., 1199 North Fairfax Street,

Alexandria, Virginia 22314. This information may be examined at the

Federal Aviation Administration (FAA), Transport Airplane Directorate,

Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the

Office of the Federal Register, 800 North Capitol Street, NW., suite

700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Mark Quam, Aerospace Engineer,

Standardization Branch, ANM-113, FAA, Transport Airplane Directorate,

1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206)

227-2145; fax (206) 227-1320.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal

Aviation Regulations (14 CFR part 39) to include an airworthiness

directive (AD) that is applicable to certain Fokker Model F27 series

airplanes was published in the Federal Register on March 14, 1994 (59

FR 11737). That action proposed to require certain structural

modifications of certain Fokker Model F27 series airplanes prior to

their economic design goal. -

Interested persons have been afforded an opportunity to participate

in the making of this amendment. Due consideration has been given to

the comments received. -

One commenter supports the proposed rule. -

One commenter requests a revision to the applicability statement to

specify the series of Fokker Model F27 airplanes affected

by the proposal. The commenter states that listing the series of the

affected airplane model in the proposal would avoid confusion. The

commenter notes that attempting to list all exclusions, as in the

proposal, would require listing all future series and derivatives of

future models, which would be impossible. The FAA concurs. The final

rule has been revised to specify that the rule is applicable to Model

F27 Mark 100, 200, 300, 400, 500, 600, and 700 airplanes.-

This commenter also requests that the proposal be revised to

specify the service bulletins referenced in Fokker Report Number SE-

278, ``F27 Aging Aircraft Project--Final Document,'' Issue 3, dated

February 1, 1993 (hereinafter referred to as the ``Fokker Report''),

rather than merely referencing Part II of the Fokker Report, as was

done in the proposal. The commenter requests this change because Fokker

Service Bulletin F27/57-68, which was referenced in Part II of the

Fokker Report, has been revised since issuance of the Fokker Report.

Thus, this commenter contends that referring to the Fokker Report will

not reflect this latest revision to that service bulletin. One

commenter notes that the Rijksluchtvaartdienst (RLD), which is the

airworthiness authority of the Netherlands, has issued a correction to

Netherlands Airworthiness Directive (BLA) 91-058/5 (A), dated July 16,

1993, to reference Revision 1 of Fokker Service Bulletin F27/57-58,

dated May 17, 1993.

The FAA concurs in part. Fokker Service Bulletin F27/57-68,

Revision 1, dated May 17, 1993, was revised to correct the reference to

the Netherlands airworthiness directive number, to add further

explanatory information in the Description section of the service

bulletin, and to make minor editorial changes to the Accomplishment

Instructions. The FAA finds that none of these changes are substantive

in nature; therefore, these changes do not warrant a revision to the

specific service information referenced in the final rule. However, the

FAA recognizes that operators may choose to comply with Revision 1 of

that service bulletin. For those operators, a new NOTE 2 has been added

to paragraph (a) of the final rule stating that compliance with

Revision 1 of that service bulletin would constitute compliance with

the requirements of Fokker Service Bulletin F27/57-68, dated July 17,

1992, which is referenced in the Fokker Report. Further, when the

Fokker Report is revised to incorporate substantive revisions of

service bulletins referenced in it, the FAA may consider further

rulemaking to incorporate those changes. -

Several commenters request that the proposal be revised to include

the modification of certain lower stringers in the outer wing of the

airplane described in Fokker Service Bulletin F27/57-70. These

commenters contend that the threshold, resource requirements, and

modification procedures specified in Fokker Service Bulletin 57-70 are

identical to those described in Fokker Service Bulletin 57-68; the only

difference is that Fokker Service Bulletin 57-68 specifies modification

of certain upper stringers in the outer wing of the airplane. Fokker

Service Bulletin 57-68 is referenced in the Fokker Report. These

commenters assert that the modifications specified in both of these

service bulletins should be included in the requirements of the

proposed rule. Further, these commenters note that the RLD has

classified Fokker Service Bulletin F27/57-70 as mandatory and has

issued Netherlands Airworthiness Directive (BLA) 93-094 in order to

ensure that the modification is accomplished on airplanes in the

Netherlands. -

The FAA does not concur that a revision to the rule to include a

requirement for the additional modification should be made at this

time. To do so would necessitate, under the provisions of the

Administrative Procedure Act, reissuing the notice, reopening the

period for public comment, considering additional comments received,

and eventually issuing a final rule. The FAA does not consider it

appropriate to delay issuance of this final rule further in order to

undertake those procedures. However, the FAA may consider further

rulemaking action to require modification of the lower stringers in

which cracking was detected coincidentally while accomplishing the

modification described in Fokker Service Bulletin F27/57-68.-

Several commenters request an extension of the proposed compliance

date of January 1, 1995, to accomplish the modification described in

Fokker Service Bulletin F27/57-68, which is one of the service

bulletins referenced in the Fokker Report. For airplanes that have

accumulated more than 30,000 total landings, that Fokker service

bulletin recommends accomplishment of the modification of certain upper

stringers of the outer wing prior to January 1, 1995. These commenters

state that such a compliance time would impose a tremendous economic

burden, since a majority of the airplanes in their fleet have already

accumulated more than 30,000 total landings; therefore, some of these

commenters suggest a compliance date of January 1, 1996, instead. One

of these commenters requests that the compliance time be revised to an

interval that coincides with the operator's regularly scheduled

maintenance.-

The FAA concurs that the compliance time for accomplishing the

modification described in Fokker Service Bulletin F27/57-68, Revision

1, dated May 17, 1993, may be extended to January 1, 1996, for

airplanes that have accumulated more than 30,000 total landings.

However, the FAA finds that in order to ensure safety in the interim,

an additional x-ray inspection must be performed until such time that

the airplane is modified, or prior to January 1, 1996. This extension

to the compliance time should allow operators to accomplish the

modification coincidentally with regularly scheduled maintenance.

Accordingly, the final rule has been revised to add a new paragraph (b)

to specify this provision. -

As a result of recent communications with the Air Transport

Association (ATA) of America, the FAA has learned that, in general,

some operators may misunderstand the legal effect of AD's on airplanes

that are identified in the applicability provision of the AD, but that

have been altered or repaired in the area addressed by the AD. The FAA

points out that all airplanes identified in the applicability provision

of an AD are legally subject to the AD. If an airplane has been altered

or repaired in the affected area in such a way as to affect compliance

with the AD, the owner or operator is required to obtain FAA approval

for an alternative method of compliance with the AD, in accordance with

the paragraph of each AD that provides for such approvals. A note has

been added to this final rule to clarify this requirement. -

Additionally, the FAA has recently reviewed the figures it has used

over the past several years in calculating the economic impact of AD

activity. In order to account for various inflationary costs in the

airline industry, the FAA has determined that it is necessary to

increase the labor rate used in these calculations from $55 per work

hour to $60 per work hour. The economic impact information, below, has

been revised to reflect this increase in the specified hourly labor

rate.-

After careful review of the available data, including the comments

noted above, the FAA has determined that air safety and the public

interest require the adoption of the rule with the changes previously

described. The FAA has determined that these changes will neither

increase the economic burden on any operator nor increase

the scope of the AD.-

The FAA estimates that 58 airplanes of U.S. registry will be

affected by this AD, within the initial threshold. Since not all

affected airplanes will be required to accomplish every modification

referenced in each of the service bulletins, the cost impact of the

modifications required by this AD is estimated in the following table.

This cost includes the price of modification kits, and the estimated

labor rate is $60 per work hour. It does not include the cost of

downtime, planning, set up, familiarization, or tool acquisition.

----------------------------------------------------------------------------------------------------------------

No. of Cost of Total cost for

Service bulletin number affected No. of work parts per Cost per affected

airplanes hours airplane airplane airplanes

----------------------------------------------------------------------------------------------------------------

55-33 (B-77)................................ 5 40 $314 $2,714.00 $13,570.00

55-12 (B-67)................................ 5 20 121 1,321.00 6,605.00

55-12 (Part II)............................. 5 30 168 1,968.00 9,840.00

55-61 Revision 2............................ 13 45 2,235 4,935.00- 64,155.00

57-68 Revision 1............................ 58 556 1,279 34,639.00 2,009,062.00

53-19 (B-45) Issue 3........................ 5 22 0 1,320.00 6,600.00

53-58 (B-149)............................... 5 16 0 960.00 4,800.00

53-76 (B-211)............................... 13 0.25 0 15.00 195.00

57-7 Issue 1................................ 5 32 400 2,320.00 11,600.00-

----------------------------------------------------------------------------------------------------------------

Based on the above figures, the total cost impact of the proposed

AD on U.S. operators is estimated to be 2,126,427.-

The total cost impact figure discussed above is based on

assumptions that no operator has yet accomplished any of the

requirements of this AD action, and that no operator would accomplish

those actions in the future if this AD were not adopted. -

The FAA recognizes that the modifications will require a large

number of work hours to accomplish. However, the threshold specified in

each of the service bulletins referenced by the Fokker Report should

allow ample time for the accomplishment of the modifications

coincidentally with scheduled major airplane inspection and maintenance

activities, thereby minimizing the costs associated with special

airplane scheduling.-

The FAA recognizes that the obligation to maintain aircraft in an

airworthy condition is vital, but sometimes expensive. Because AD's

require specific actions to address specific unsafe conditions, they

appear to impose costs that would not otherwise be borne by operators.

However, because of the general obligation of operators to maintain

aircraft in an airworthy condition, this appearance is deceptive.

Attributing those costs solely to the issuance of this AD is

unrealistic because, in the interest of maintaining safe aircraft, most

prudent operators would accomplish the required actions even if they

were not required to do so by the AD. -

A full cost-benefit analysis has not been accomplished for this AD.

As a matter of law, in order to be airworthy, an aircraft must conform

to its type design and be in a condition for safe operation. The type

design is approved only after the FAA makes a determination that it

complies with all applicable airworthiness requirements. In adopting

and maintaining those requirements, the FAA has already made the

determination that they establish a level of safety that is cost-

beneficial. When the FAA, as in this AD, makes a finding of an unsafe

condition, this means that the original cost-beneficial level of safety

is no longer being achieved and that the required actions are necessary

to restore that level of safety. Because this level of safety has

already been determined to be cost-beneficial, a full cost-benefit

analysis for this AD would be redundant and unnecessary.-

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.-

For the reasons discussed above, I certify that this action (1) is

not a ``significant regulatory action'' under Executive Order 12866;

(2) is not a ``significant rule'' under DOT Regulatory Policies and

Procedures (44 FR 11034, February 26, 1979); and (3) will not have a

significant economic impact, positive or negative, on a substantial

number of small entities under the criteria of the Regulatory

Flexibility Act. A final evaluation has been prepared for this action

and it is contained in the Rules Docket. A copy of it may be obtained

from the Rules Docket at the location provided under the caption

ADDRESSES.

List of Subjects in 14 CFR Part 39-

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment -

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES-

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. App. 1354(a), 1421 and 1423; 49 U.S.C.

106(g); and 14 CFR 11.89.

Sec. 39.13 [Amended]-

2. Section 39.13 is amended by adding the following new

airworthiness directive:

94-26-08 Fokker: Amendment 39-9103. Docket 93-NM-229-AD.

Applicability: Model F27 Mark 100, 200, 300, 400, 500, 600, and

700 airplanes, as listed in Fokker Report Number SE-278, ``F27 Aging

Aircraft Project--Final Document,'' Issue 3, dated February 1, 1993;

certificated in any category.

-Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must use the authority

provided in paragraph (c) to request approval from the FAA. This

approval may address either no action, if the current configuration

eliminates the unsafe condition; or different actions necessary to

address the unsafe condition described in this AD. Such a request

should include an assessment of the effect of the

changed configuration on the unsafe condition addressed by this AD.

In no case does the presence of any modification, alteration, or

repair remove any airplane from the applicability of this AD. -

Compliance: Required as indicated, unless accomplished

previously. -

To prevent structural failure, accomplish the following: -

(a) Except as provided for by paragraph (b) of this AD, prior to

reaching the incorporation thresholds listed in Part II of Fokker

Report Number SE-278, ``F27 Aging Aircraft Project--Final

Document,'' Issue 3, dated February 1, 1993 (hereinafter referred to

as the ``Fokker Report''), accomplish the structural modifications

listed in Part II of the Fokker Report.

Note 2: Compliance in accordance with Fokker Service Bulletin

F27/57-68, Revision 1, dated May 17, 1993, constitutes compliance

with Fokker Service Bulletin F27/57-68, dated July 17, 1992, which

is referenced in the Fokker Report.-

Note 3: The modifications required by this paragraph do not

terminate the inspection requirements of any other AD unless that AD

specifies that any such modification constitutes terminating action

for that inspection requirement.

(b) For airplanes that have accumulated 30,000 total landings or

more as of the threshold specified in Fokker Service Bulletin F27/

57-68, Revision 1, dated May 17, 1993, referenced in the Fokker

Report: The incorporation threshold for accomplishing the structural

modification may be extended to January 1, 1996, if an x-ray

inspection of the stringers at stations 11260, 12660, and 13460 is

performed in accordance with Part 2 of Fokker Service Bulletin F27/

57-68, Revision 1, dated May 17, 1993, at the time specified in

either paragraph (b)(1) or (b)(2) of this AD, as applicable. If

cracking is detected, prior to further flight, repair in accordance

with paragraph 1.D.(1)(c) of the service bulletin.-

(1) For airplanes on which the inspections of the top skin of

stringers 4 through 7 are currently being performed in accordance

with Part 2 of Fokker Service Bulletin F27/57-68, Revision 1, dated

May 17, 1993: Within 4,000 landings from the immediately preceding

inspection.-

(2) For airplanes on which the inspections of the top skin of

stringers 4 through 7 are not currently being performed in

accordance with Part 2 of Fokker Service Bulletin F27/57-68,

Revision 1, dated May 17, 1993: Within 2 months after the effective

date of this AD, -

(c) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Standardization Branch, ANM-113,

FAA, Transport Airplane Directorate. Operators shall submit their

requests through an appropriate FAA Principal Maintenance Inspector,

who may add comments and then send it to the Manager,

Standardization Branch, ANM-113.

-Note 4: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Standardization Branch, ANM-113.

(d) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished. -

(e) The structural modifications shall be done in accordance

with Fokker Report Number SE-278, ``F27 Aging Aircraft Project--

Final Document,'' Issue 3, dated February 1, 1993, which contains

the following list of effective pages:-

------------------------------------------------------------------------

Revision

Page number- level shown Date shown on page

on page-

------------------------------------------------------------------------

-1-3, II.3..................... 3 February 1, 1993.

4-7, I.2-I.14.................. 2 February 1, 1993.

I.1, I.15, I.16, II.1, II.2, 1 May 3, 1991.

II.4, III.1, III.2.

------------------------------------------------------------------------

APPENDIX A

------------------------------------------------------------------------

APP. A-1....................... 2 February 1, 1993.

------------------------------------------------------------------------

APPENDIX B

------------------------------------------------------------------------

1-13........................... 2 February 1, 1993.

------------------------------------------------------------------------

APPENDIX C

------------------------------------------------------------------------

1.............................. Original September 27, 1990.

2-5-........................... (These

pages are

not dated)

------------------------------------------------------------------------

APPENDIX D

------------------------------------------------------------------------

1-5-........................... Original February 1, 1993.

------------------------------------------------------------------------

APPENDIX E

------------------------------------------------------------------------

``Structural Maintenance May 22, 1991.-

Program Guidelines. . .''.

``Structural Maintenance May 22, 1991.

Program Task. . .''.

Table of Contents.............. May 22, 1991.

1-17........................... Original May 22, 1991.

------------------------------------------------------------------------

This incorporation by reference was approved by the Director of

the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR

part 51. Copies may be obtained from Fokker Aircraft USA, Inc., 1199

North Fairfax Street, Alexandria, Virginia 22314. Copies may be

inspected at the FAA, Transport Airplane Directorate, 1601 Lind

Avenue, SW., Renton, Washington; or at the Office of the Federal

Register, 800 North Capitol Street, NW., suite 700, Washington, DC.-

(f) This amendment becomes effective on February 3, 1995.

Issued in Renton, Washington, on December 19, 1994.

Darrell M. Pederson,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 95-51 Filed 1-3-95; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.