[No title available]
FederalRegulations
Ask Donna
How this section applies to your facts.
Federal Register › Vol. 60 › 60 FR 328
Text
been added to this final rule to clarify
this requirement. The FAA has
determined that this addition will
neither increase the economic burden
on any operator nor increase the scope
of the AD.
The FAA has recently reviewed the
figures it has used over the past several
years in calculating the economic
impact of AD activity. In order to
account for various inflationary costs in
the airline industry, the FAA has
determined that it is necessary to
increase the labor rate used in these
calculations from $55 per work hour to
$60 per work hour. The economic
impact information, below, has been
revised to reflect this increase in the
specified hourly labor rate.
There are approximately 20 Lockheed
Model 382 series airplanes of the
affected design in the worldwide fleet.
The FAA estimates that it will will take
approximately 4 work hours per
airplane to accomplish the required
actions, and that the average labor rate
is $60 per work hour. Based on these
figures, the total cost impact of the AD
on U.S. operators is estimated to be
$4,800, or $240 per airplane.
The total cost impact figure discussed
above is based on assumptions that no
operator has yet accomplished any of
the requirements of this AD action, and
that no operator would accomplish
those actions in the future if this AD
were not adopted.
The regulations adopted herein will
not have substantial direct effects on the
States, on the relationship between the
national government and the States, or
on the distribution of power and
responsibilities among the various
levels of government. Therefore, in
accordance with Executive Order 12612,
it is determined that this final rule does
not have sufficient federalism
implications to warrant the preparation
of a Federalism Assessment.
For the reasons discussed above, I
certify that this action (1) is not a
``significant regulatory action'' under
Executive Order 12866; (2) is not a
``significant rule'' under DOT
Regulatory Policies and Procedures (44
FR 11034, February 26, 1979); and (3)
will not have a significant economic
impact, positive or negative, on a
substantial number of small entities
under the criteria of the Regulatory
Flexibility Act. A final evaluation has
been prepared for this action and it is
contained in the Rules Docket. A copy
of it may be obtained from the Rules
Docket at the location provided under
the caption ADDRESSES .
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation
safety, Incorporation by reference,
Safety.
Adoption of the Amendment
Accordingly, pursuant to the
authority delegated to me by the
Administrator, the Federal Aviation
Administration amends part 39 of the
Federal Aviation Regulations (14 CFR
part 39) as follows:
PART 39ÐAIRWORTHINESS
DIRECTIVES
1. The authority citation for part 39
continues to read as follows:
Authority: 49 U.S.C. App. 1354(a), 1421
and 1423; 49 U.S.C. 106(g); and 14 CFR
11.89.
§ 39.13 [Amended]
2. Section 39.13 is amended by
adding the following new airworthiness
directive:
94-26-15 Lockheed Aeronautical Systems
Company: Amendment 39-9110. Docket
94-NM-88-AD.
Applicability: Model 382, 382B, 382E,
382F, and 382G series airplanes, as listed in
Hercules Service Bulletin 382-57-74 (82-688), dated January 31, 1994; certificated in
any category.
Note 1: This AD applies to each airplane
identified in the preceding applicability
provision, regardless of whether it has been
modified, altered, or repaired in the area
subject to the requirements of this AD. For
airplanes that have been modified, altered, or
repaired so that the performance of the
requirements of this AD is affected, the
owner/operator must use the authority
provided in paragraph (b) to request approval
from the FAA. This approval may address
either no action, if the current configuration
eliminates the unsafe condition; or different
actions necessary to address the unsafe
condition described in this AD. Such a
request should include an assessment of the
effect of the changed configuration on the
unsafe condition addressed by this AD. In no
case does the presence of any modification,
alteration, or repair remove any airplane from
the applicability of this AD.
Compliance: Required as indicated, unless
accomplished previously.
To prevent structural failure of the outer
wing assembly, accomplish the following:
(a) Within 30 days after the effective date
of this AD, or prior to the accumulation of
18,000 total flight hours, whichever occurs
later, perform an ultrasonic inspection to
determine the distance between the edge of
each of the six most outboard fasteners on
kingpin riser number 18 and the edge of the
riser, in accordance with Appendix A of
Hercules Service Bulletin 382-57-74 (82-688), dated January 31, 1994.
(1) If all six of these fasteners are
positioned 0.31 inch or more from the
kingpin riser edge: No further action is
required by this AD.
(2) If any of the six most outboard fasteners
is positioned less than 0.31 inch from the
edge of the kingpin riser: Prior to the
applicable threshold specified in Table 1 of
Hercules Service Bulletin 382-57-74 (82-688), or prior to further flight if that
threshold has been exceeded as of the
effective date of this AD, perform an
ultrasonic inspection to detect cracks in the
kingpin riser, in accordance with Inspection
Procedure SP-265 (Appendix B) of the
service bulletin.
Note 2: For airplanes on which an outer
wing replacement is installed, the total flight
hours threshold is counted from the time of
outer wing replacement.
(i) If no crack is found, repeat this
inspection, thereafter, at intervals not to
exceed 7,400 flight hours.
(ii) If any cracked kingpin riser is found,
prior to further flight, repair in accordance
with a method approved by the Manager,
Atlanta Aircraft Certification Office (ACO),
FAA, Small Airplane Directorate. Repeat this
inspection, thereafter, at intervals not to
exceed 7,400 flight hours.
(b) An alternative method of compliance or
adjustment of the compliance time that
provides an acceptable level of safety may be
used if approved by the Manager, Atlanta
ACO, FAA, Small Airplane Directorate.
Operators shall submit their requests through
an appropriate FAA Principal Maintenance
Inspector, who may add comments and then
send it to the Manager, Atlanta ACO.
Note 3: Information concerning the
existence of approved alternative methods of
compliance with this AD, if any, may be
obtained from the Atlanta ACO.
(c) Special flight permits may be issued in
accordance with sections 21.197 and 21.199
of the Federal Aviation Regulations (14 CFR
21.197 and 21.199) to operate the airplane to
a location where the requirements of this AD
can be accomplished.
(d) The inspections shall be done in
accordance with Hercules Service Bulletin
382-57-74 (82-688), dated January 31, 1994
(includes Attachment 1, and Appendices A
and B). This incorporation by reference was
approved by the Director of the Federal
Register in accordance with 5 U.S.C. 552(a)
and 1 CFR part 51. Copies may be obtained
from Lockheed Aeronautical Systems
Support Company, Field Support
Department, Department 693, Zone 0755,
2251 Lake Park Drive, Smyrna, Georgia
30080. Copies may be inspected at the FAA,
Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the
FAA, Small Airplane Directorate, Atlanta
Certification Office, Campus Building, 1701
Columbia Avenue, Suite 2-160, College Park,
Georgia; or at the Office of the Federal
Register, 800 North Capitol Street, NW., suite
700, Washington, DC.
(e) This amendment becomes effective on
February 3, 1995.
Issued in Renton, Washington, on
December 21, 1994.
Darrell M. Pederson,
Acting Manager, Transport Airplane
Directorate, Aircraft Certification Service.
[FR Doc. 95-48 Filed 1-3-95; 8:45 am]
BILLING CODE 4910-13-U
This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.