Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 60 › 60 FR 329

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 94-NM-108-AD; Amendment 39-9109; AD 94-26-14]

Airworthiness Directives; British Aerospace Model Viscount 744,

745D, and 810 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),

applicable to all British Aerospace Model Viscount 744, 745D, and 810

series airplanes, that requires inspections to detect cracks in the

chassis side bracing structure and in the chassis top strut support

intercostals inside the wings, and replacement of discrepant parts with

new parts. This proposal would also require inspection of the

intercostals to determine the specification of the material, if

necessary, and replacement of discrepant parts with new parts. This

amendment is prompted by a report of cracking in the chassis top strut

support intercostal in the side bracing structure inside the wing due

to the effects of metal fatigue. The actions specified by this AD are

intended to prevent such fatigue-related cracking, which could lead to

the failure of the chassis side bracing structure inside the wings and

consequent reduced structural integrity of the chassis support

structure.

DATES: Effective on February 3, 1995.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of February 3, 1995.

ADDRESSES: The service information referenced in this AD may be

obtained from British Aerospace Regional Aircraft Ltd., Engineering

Support Manager, Military Business Unit, Chadderton Works, Greengate,

Middleton, Manchester M24 1SA, England. This information may be

examined at the Federal Aviation Administration (FAA), Transport

Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton,

Washington; or at the Office of the Federal Register, 800 North Capitol

Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: William Schroeder, Aerospace Engineer,

Standardization Branch, ANM-113, FAA, Transport Airplane Directorate,

1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206)

227-2148; fax (206) 227-1320.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal

Aviation Regulations (14 CFR part 39) to include an airworthiness

directive (AD) that is applicable to all British Aerospace Model

Viscount 744, 745D, and 810 series airplanes was published in the

Federal Register on September 9, 1994 (59 FR 46596). That action

proposed to require repetitive detailed visual inspections to detect

cracks in the chassis side bracing structure and in the chassis top

strut support intercostals of the inner wings, and replacement of

discrepant parts with new parts. That action also proposed to require

an eddy current inspection to determine the specification of the

material of the intercostals, if necessary, and replacement of

discrepant parts with new parts.

Interested persons have been afforded an opportunity to participate

in the making of this amendment. Due consideration has been given to

the single comment received.

The commenter supports the proposed rule.

As a result of recent communications with the Air Transport

Association (ATA) of America, the FAA has learned that, in general,

some operators may misunderstand the legal effect of AD's on airplanes

that are identified in the applicability provision of the AD, but that

have been altered or repaired in the area addressed by the AD. The FAA

points out that all airplanes identified in the applicability provision

of an AD are legally subject to the AD. If an airplane has been altered

or repaired in the affected area in such a way as to affect compliance

with the AD, the owner or operator is required to obtain FAA approval

for an alternative method of compliance with the AD, in accordance with

the paragraph of each AD that provides for such approvals. A note has

been added to this final rule to clarify this requirement.

The FAA has recently reviewed the figures it has used over the past

several years in calculating the economic impact of AD activity. In

order to account for various inflationary costs in the airline

industry, the FAA has determined that it is necessary to increase the

labor rate used in these calculations from $55 per work hour to $60 per

work hour. The economic impact information, below, has been revised to

reflect this increase in the specified hourly labor rate.

After careful review of the available data, including the comment

noted above, the FAA has determined that air safety and the public

interest require the adoption of the rule with the changes previously

described. The FAA has determined that these changes will neither

increase the economic burden on any operator nor increase the scope of

the AD.

The FAA estimates that 25 Model Viscount 744 and 745D series

airplanes of U.S. registry will be affected by this AD, that it will

take approximately 15 work hours per airplane to accomplish the

required actions, and that the average labor rate is $60 per work hour.

Based on these figures, the total cost impact of the AD on U.S.

operators is estimated to be $22,500, or $900 per airplane, per

inspection cycle.

The FAA estimates that 4 Model Viscount 810 series airplanes of

U.S. registry will be affected by this AD, that it will take

approximately 15 work hours per airplane to accomplish the required

actions, and that the average labor rate is $60 per work hour. Based on

these figures, the total cost impact of the proposed AD on U.S.

operators is estimated to be $3,600, or $900 per airplane, per

inspection cycle.

Based on the above figures, the total cost impact of the actions

proposed by this AD on U.S. operators is estimated to be $26,100, or

$900 per airplane, per inspection cycle.

The total cost impact figure discussed above is based on

assumptions that no operator has yet accomplished any of the

requirements of this AD action, and that no operator would accomplish

those actions in the future if this AD were not adopted.

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is

not a ``significant regulatory action'' under Executive Order 12866;

(2) is not a ``significant rule'' under DOT Regulatory Policies and

Procedures (44 FR 11034, February 26, 1979); and (3) will not have a

significant economic impact, positive or negative, on a substantial

number of small entities under the criteria of the Regulatory

Flexibility Act. A final evaluation has been prepared for this action

and it is contained in the Rules Docket. A copy of it may be obtained

from the Rules Docket at the location provided under the caption

ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. App. 1354(a), 1421 and 1423; 49 U.S.C.

106(g); and 14 CFR 11.89.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

94-26-14 British Aerospace Regional Aircraft Limited (Formerly

British Aerospace Commercial Aircraft Limited, Vickers-Armstrongs

Aircraft Limited): Amendment 39-9109. Docket 94-NM-108-AD.

Applicability: All Model Viscount 744, 745D, and 810 series

airplanes, certificated in any category.

Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must use the authority

provided in paragraph (b) to request approval from the FAA. This

approval may address either no action, if the current configuration

eliminates the unsafe condition; or different actions necessary to

address the unsafe condition described in this AD. Such a request

should include an assessment of the effect of the changed

configuration on the unsafe condition addressed by this AD. In no

case does the presence of any modification, alteration, or repair

remove any airplane from the applicability of this AD.

Compliance: Required as indicated, unless accomplished

previously.

To prevent reduced structural integrity of the chassis,

accomplish the following:

(a) Within 6 months after the effective date of this AD, perform

a detailed visual inspection to detect cracks in the chassis side

bracing structure and in the chassis top strut support intercostals

inside the wings between stations 81 and 96, in accordance with

British Aerospace Viscount Preliminary Technical Leaflet (PTL) 332,

Issue 1, Disc 11 Doc.4, dated December 2, 1991 (for Model Viscount

744 and 745D series airplanes); or British Aerospace Viscount PTL

203, Issue 1, Disc 11 Doc.2, dated December 2, 1991 (for Model

Viscount 810 series airplanes); as applicable.

(1) If no cracking is detected in the chassis side bracing

structure, repeat the inspection thereafter at intervals not to

exceed 1,500 flight hours or 14 months, whichever occurs first.

(2) If any cracking is detected in the chassis side bracing

structure, prior to further flight, replace the cracked side of the

bracing structure with a new structure, in accordance with the

applicable PTL.

(3) If no cracking is detected in the chassis top strut support

intercostal, prior to further flight, perform an eddy current

inspection to determine the specification of the material (either

L72 or L73) of the intercostals, in accordance with the applicable

PTL.

(i) If the material is manufactured from L72, prior to further

flight, replace the chassis top strut support intercostal with a new

chassis top strut support intercostal, in accordance with the

applicable PTL.

(ii) If the material is manufactured from L73, no further action

is required by paragraph (a)(3) of this AD.

(4) If cracking is detected in the chassis top strut support

intercostal, prior to further flight, replace it with a new chassis

top strut support intercostal, in accordance with the applicable

PTL.

(b) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Standardization Branch, ANM-113,

FAA, Transport Airplane Directorate. Operators shall submit their

requests through an appropriate FAA Principal Maintenance Inspector,

who may add comments and then send it to the Manager,

Standardization Branch, ANM-113.

Note 2: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Standardization Branch, ANM-113.

(c) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished.

(d) The inspections and replacements shall be done in accordance

with British Aerospace Viscount Preliminary Technical Leaflet (PTL)

332, Issue 1, Disc 11 Doc.4, dated December 2, 1991 (for Model

Viscount 744 and 745D series airplanes); or British Aerospace

Viscount PTL 203, Issue 1, Disc 11 Doc.2, dated December 2, 1991

(for Model Viscount 810 series airplanes); as applicable. This

incorporation by reference was approved by the Director of the

Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part

51. Copies may be obtained from British Aerospace Regional Aircraft

Ltd., Engineering Support Manager, Military Business Unit,

Chadderton Works, Greengate, Middleton, Manchester M24 1SA, England.

Copies may be inspected at the FAA, Transport Airplane Directorate,

1601 Lind Avenue, SW., Renton, Washington; or at the Office of the

Federal Register, 800 North Capitol Street, NW., suite 700,

Washington, DC.

(e) This amendment becomes effective on February 3, 1995.

Issued in Renton, Washington, on December 21, 1994.

Darrell M. Pederson,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 95-49 Filed 1-3-95; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.

Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes · 60 FR 329 | Frix