Airworthiness Directives; Empresa Brasileira de Aeronautica S.A., Models EMB-110P1 and EMB-110P2 Airplanes

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 63 › 63 FR 1337

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 96-CE-66-AD; Amendment 39-10273; AD 98-01-10]

RIN 2120-AA64

Airworthiness Directives; Empresa Brasileira de Aeronautica S.A.,

Models EMB-110P1 and EMB-110P2 Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment supersedes Airworthiness Directive (AD) 87-03-

10, which currently requires repetitively inspecting the fillet area of

both the left and right main landing gear (MLG) wheel axle/piston tube

support junction area for cracks on Empresa Brasileira de Aeronautica

S.A. (EMBRAER) Models EMB-110P1 and EMB-110P2 airplanes, and requires

replacing any MLG wheel axle/piston tube assembly where a crack is

found. AD 87-03-10 also provided the option of reworking this area when

no cracks were found as terminating action for the repetitive

inspections. The Federal Aviation Administration's policy on aging

commuter-class aircraft is to eliminate or, in certain instances,

reduce the number of certain repetitive short-interval inspections when

improved parts or modifications are available. This AD requires the

following on EMBRAER Models EMB 110-P1 and EMB 110-P2 airplanes that do

not have an ``R'' stamped on both the left and right MLG wheel axle/

piston tube assembly end-piece: inspecting (one-time) the fillet area

of each MLG wheel axle/piston tube support junction area to assure that

the area is free of cracks, replacing any MLG wheel axle/piston tube

assembly if a crack is found, and reworking this area on both the left

and right MLG's, as terminating action for the repetitive inspections

that are currently required by AD 87-03-10. The actions specified in

this AD are intended to prevent failure of the MLG wheel axle/piston

tube assembly caused by fatigue cracking, which could result in loss of

control of the airplane during landing operations.

DATES: Effective February 9, 1998.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of February 9, 1998.

ADDRESSES: Service information that applies to this AD may be obtained

from EMBRAER, Av. Brig Faira Lima 2170, 12227-901, Sao Jose dos Campos-

SP, Brazil. This information may also be examined at the Federal

Aviation Administration (FAA), Central Region, Office of the Regional

Counsel, Attention: Rules Docket 96-CE-66-AD, Room 1558, 601 E. 12th

Street, Kansas City, Missouri 64106; or at the Office of the Federal

Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Mr. Curtis Jackson, Aerospace

Engineer, FAA, Atlanta Aircraft Certification Office, Campus Building,

1701 Columbia Avenue, suite 2-160, College Park, Georgia 30337-2748;

telephone (404) 305-7358; facsimile (404) 305-7348.

SUPPLEMENTARY INFORMATION:

Events Leading to the Issuance of This AD

A proposal to amend part 39 of the Federal Aviation Regulations (14

CFR part 39) to include an AD that would apply to EMBRAER Models EMB-

110P1 and EMB-110P2 airplanes that do not have an ``R'' stamped on both

the left and right MLG wheel axle/piston tube assembly end-piece was

published in the Federal Register as a notice of proposed rulemaking

(NPRM) on March 12, 1997 (62 FR 11384). The NPRM proposed to supersede

AD 87-03-10 with a new AD that would require inspecting (one-time) the

fillet area of both the left and right MLG wheel axle/piston tube

support junction area to assure that the area is free of cracks,

replacing any MLG wheel axle/piston tube assembly if a crack is found,

and reworking this area on both the left and right MLG's, as

terminating action for the repetitive inspections that are currently

required by AD 87-03-10. Airplanes that have an ``R'' stamped on both

the left and right MLG wheel axle/piston tube assembly end-piece either

(1) have a design configuration that is different from the unsafe

condition specified in this document; or (2) the airplanes already have

both the left and right MLG wheel axle/piston tube assembly reworked.

Accomplishment of the proposed inspection as specified in the NPRM

would be in accordance with EMBRAER Service Bulletin (SB) No. 110-032-

0068, dated December 20, 1985. Accomplishment of the proposed rework as

specified in the NPRM would be required in accordance with EMBRAER SB

No. 110-032-0071, Change No. 01, dated June 21, 1988.

Interested persons have been afforded an opportunity to participate

in the making of this amendment. No comments were received on the

proposed rule or the FAA's determination of the cost to the public.

The FAA's Determination

After careful review of all available information related to the

subject presented above, the FAA has determined that air safety and the

public interest require the adoption of the rule as proposed except for

minor editorial corrections. The FAA has determined that these minor

corrections will not change the meaning of the AD and will not add any

additional burden upon the public than was already proposed.

Cost Impact

The FAA estimates that 50 airplanes in the U.S. registry will be

affected by this AD, that it will take approximately 22 workhours

(inspection: 8 workhours; rework: 14 workhours) per airplane to

accomplish this AD, and that the average labor rate is approximately

$60 an hour. There is no cost for parts to accomplish this AD. Based on

these figures, the total cost impact of this AD on U.S. operators is

estimated to be $66,000.

The initial inspection cost of this AD is the same as that required

by AD 87-03-10. The difference in the inspection costs of this AD and

AD 87-03-10 is that this AD does not require the repetitive inspections

and AD 87-03-10 currently requires repetitive inspections every 1,000

landings. The required rework eliminates the repetitive inspection

requirement, and is optional in AD 87-03-10.

The FAA does not have any way of determining how many airplanes

have an ``R'' stamped on both the left and right MLG wheel axle/piston

tube support junction area end-piece and have these areas reworked,

and, therefore already have the actions of this AD accomplished. The

affected airplanes are no longer in production with few airplanes being

operated in the United States. Since AD 87-03-10 provided the option of

reworking the area on both the left and right MLG's as terminating

action for the repetitive inspections, the FAA believes that most of

the operators will have accomplished the rework and will not be

affected by this AD.

The FAA's Aging Commuter Aircraft Policy

The actions required by this AD are consistent with the FAA's aging

commuter aircraft policy, which briefly states that, when a

modification exists that could eliminate or reduce the number of

required critical inspections, the modification should be incorporated.

This policy is based on the FAA's determination that reliance on

critical repetitive inspections on airplanes utilized in commuter

service carries an unnecessary safety risk when a design change exists

that could eliminate or, in certain instances, reduce the number of

those critical inspections. In determining what inspections are

critical, the FAA considers (1) the safety consequences of the airplane

if the known problem is not detected by the inspection; (2) the

reliability of the inspection such as the probability of not detecting

the known problem; (3) whether the inspection area is difficult to

access; and (4) the possibility of damage to an adjacent structure as a

result of the problem.

The alternative to reworking the fillet area of the left and right

MLG wheel axle/piston tube support junction area is to rely on the

repetitive inspections currently required by AD 87-03-10 to detect

cracks in this area.

Regulatory Impact

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is

not a ``significant regulatory action'' under Executive Order 12866;

(2) is not a ``significant rule'' under DOT Regulatory Policies and

Procedures (44 FR 11034, February 26, 1979); and (3) will not have a

significant economic impact, positive or negative, on a substantial

number of small entities under the criteria of the Regulatory

Flexibility Act. A copy of the final evaluation prepared for this

action is

contained in the Rules Docket. A copy of it may be obtained by

contacting the Rules Docket at the location provided under the caption

ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by removing Airworthiness Directive

(AD) 87-03-10, Amendment 39-5524, and by adding a new AD to read as

follows:

98-01-10 Empresa Brasileira De Aeronautica S.A: Amendment 39-10273;

Docket 96-CE-66-AD. Supersedes AD 87-03-10, Amendment 39-5524.

Applicability: Models EMB-110P1 and EMB-110P2 airplanes, all

serial numbers, certificated in any category, that do not have an

``R'' stamped on both the left and right main landing gear (MLG)

wheel axle/piston tube assembly end-piece.

Note 1: Airplanes that have an ``R'' stamped on both the left

and right MLG wheel axle/piston tube assembly end-piece either (1)

have a design configuration that is different from the unsafe

condition specified in this AD; or (2) already have both the left

and right MLG wheel axle/piston tube support junction area reworked.

EMBRAER Service Bulletin (SB) No. 110-032-0071, Change No. 01, dated

June 21, 1988, includes procedures for this rework, including

stamping an ``R'' on both the left and right MLG wheel axle/piston

tube assembly end-piece.

Note 2: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must request approval for an

alternative method of compliance in accordance with paragraph (d) of

this AD. The request should include an assessment of the effect of

the modification, alteration, or repair on the unsafe condition

addressed by this AD; and, if the unsafe condition has not been

eliminated, the request should include specific proposed actions to

address it.

Compliance: Required within the next 100 landings after the

effective date of this AD, unless already accomplished.

Note 3: If the number of landings is unknown, hours time-in-

service (TIS) may be used by multiplying the number of hours TIS by

0.50. If hours TIS are utilized to calculate the number of landings,

this would make the AD effective ``within the next 200 hours TIS

after the effective date of this AD.''

To prevent failure of a MLG wheel axle/piston tube assembly

caused by fatigue cracking, which could result in loss of control of

the airplane during landing operations, accomplish the following:

(a) Inspect, using either eddy current, dye penetrant, or

magnetic particle methods, the fillet area in both the left and

right MLG wheel axle/piston support junction area for cracks in

accordance with the instructions contained in EMBRAER SB No. 110-

032-0068, dated December 20, 1985. Included in this SB is ERAM SB

No. 32-22, which includes procedures for accomplishing this

inspection. If any cracks are found, prior to further flight,

replace the MLG wheel axle/piston tube assembly with an uncracked

assembly.

(b) Visually inspect the fillet radius in both the left and

right MLG wheel axle/piston tube support junction area to determine

whether the profile requires rework. Accomplish the inspection in

accordance with the instructions in ERAM SB No. 32-25, which is part

of EMBRAER SB No. 110-032-0071, Change No. 01, dated June 21, 1988.

(1) If the profile of the area of each MLG is like the one

presented in image (A) Figure 1 of ERAM SB No. 32-25, which is part

of EMBRAER SB No. 110-032-0071, Change No. 01, dated June 21, 1988,

prior to further flight, polish the junction area using a fine grit

abrasive cloth and stamp the letter ``R'' on the MLG wheel axle/

piston tube assembly end-pipe.

(2) If the profile of the area of each MLG is like the one

presented in image (B) Figure 1 of ERAM SB No. 32-25, which is part

of EMBRAER SB No. 110-032-0071, Change No. 01, dated June 21, 1988,

prior to further flight, accomplish the following in accordance with

EMBRAER SB No. 110-032-0071, Change No. 01, dated June 21, 1988:

(i) Rework each MLG wheel axle/piston tube support junction

area;

(ii) Polish each junction area using a fine grit abrasive cloth;

and

(iii) Stamp the letter ``R'' on each MLG wheel axle/piston tube

assembly end-pipe.

(c) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished.

(d) An alternative method of compliance or adjustment of the

compliance time that provides an equivalent level of safety may be

approved by the Manager, Atlanta Aircraft Certification Office

(ACO), Campus Building, 1701 Columbia Avenue, suite 2-160, College

Park, Georgia 30337-2748.

(1) The request shall be forwarded through an appropriate FAA

Maintenance Inspector, who may add comments and then send it to the

Manager, Atlanta ACO.

(2) Alternative methods of compliance approved in accordance

with AD 87-03-10 (superseded by this action) are not considered

approved as alternative methods of compliance with this AD.

Note 4: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Atlanta ACO.

(e) The inspection required by this AD shall be done in

accordance with EMBRAER Service Bulletin No. 110-032-0068, dated

December 20, 1985. The modification (rework, polishing, and

stamping) required by this AD shall be done in accordance with

EMBRAER Service Bulletin No. 110-032-0071, Change No. 01, dated June

21, 1988. This incorporation by reference was approved by the

Director of the Federal Register in accordance with 5 U.S.C. 552(a)

and 1 CFR part 51. Copies may be obtained EMBRAER, Av. Brig Faira

Lima 2170, 12227-901, Sao Jose dos Campos-SP, Brazil. Copies may be

inspected at the FAA, Central Region, Office of the Regional

Counsel, Room 1558, 601 E. 12th Street, Kansas City, Missouri, or at

the Office of the Federal Register, 800 North Capitol Street, NW.,

suite 700, Washington, DC.

(f) This amendment (39-10273) supersedes AD 87-03-10, Amendment

39-5524.

(g) This amendment (39-10273) becomes effective on February 9,

1998.

Issued in Kansas City, Missouri, on December 24, 1997.

Michael Gallagher,

Manager, Small Airplane Directorate, Aircraft Certification Service.

[FR Doc. 98-103 Filed 1-8-98; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.