Airworthiness Directives; Airbus Model A310 and A300-600 Series Airplanes

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 63 › 63 FR 1738

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 96-NM-247-AD; Amendment 39-10282; AD 98-01-20]

RIN 2120-AA64

Airworthiness Directives; Airbus Model A310 and A300-600 Series

Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD) that

is applicable to certain Airbus Model A310 and A300-600 series

airplanes. This action requires a one-time inspection of the attachment

bolts and washers for the forward cargo container and pallet latches in

the aft cargo compartment to determine if bolts and washers having the

correct part numbers are installed; and replacement of the bolts and

washers with parts having the correct part numbers, if necessary. This

AD also requires revising the Airplane Flight Manual and certain

supplements to specify certain cargo loading procedures that must be

used until the inspection is accomplished. This amendment is prompted

by issuance of mandatory continuing airworthiness information by a

foreign civil airworthiness authority. The actions specified in this AD

are intended to prevent cargo from shifting in flight, and consequent

structural damage and reduced controllability of the airplane.

DATES: Effective January 27, 1998.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of January 27, 1998.

Comments for inclusion in the Rules Docket must be received on or

before February 11, 1998.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), Transport Airplane Directorate, ANM-114,

Attention: Rules Docket No. 96-NM-247-AD, 1601 Lind Avenue, SW.,

Renton, Washington 98055-4056.

The service information referenced in this AD may be obtained from

Airbus Industrie, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex,

France. This information may be examined at the FAA, Transport Airplane

Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the

Office of the Federal Register, 800 North Capitol Street, NW., suite

700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Norman B. Martenson, Manager,

International Branch, ANM-116, FAA, Transport Airplane Directorate,

1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)

227-2110; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION: The Direction Generale de l'Aviation Civile

(DGAC), which is the airworthiness authority for France, notified the

FAA that an unsafe condition may exist on certain Airbus Model A310 and

A300-600 series airplanes. The DGAC advises that operators have

experienced difficulties with the installation of the latches for the

forward cargo containers and pallets in the aft cargo compartment.

Investigation revealed that, in some cases, incorrect part numbers for

the attachment bolts and washers of these latches had been installed.

If the proper attachment hardware is not installed, the forward cargo

container or pallet latches could detach from the floor when subjected

to high acceleration forces during takeoff, landing, and flight. This

condition, if not corrected, could result in cargo shifting in flight,

and consequent structural damage and reduced controllability of the

airplane.

Explanation of Relevant Service Information

Airbus has issued All Operator Telex (AOT) 25 05, Revision 03,

dated June 25, 1997, which describes procedures for a one-time

inspection of the attachment bolts and washers for the forward cargo

container and pallet latches in the aft cargo compartment to determine

if bolts and washers having the correct part number are installed; and

replacement of the bolts and washers with parts having the correct part

numbers, if necessary. The AOT also describes procedures for loading

the aft cargo compartment for in-service operation. Accomplishment of

the one-time inspection and any necessary corrective action eliminates

the need for use of these loading procedures. Accomplishment of the

actions specified in the AOT is intended to adequately address the

identified unsafe condition. The DGAC classified this AOT as mandatory

and issued French airworthiness directive 97-143-227(B), dated July 2,

1997, in order to assure the continued airworthiness of these airplanes

in France.

FAA's Conclusions

These airplane models are manufactured in France and are type

certificated for operation in the United States under the provisions of

section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and

the applicable bilateral airworthiness agreement. Pursuant to this

bilateral airworthiness agreement, the DGAC has kept the FAA informed

of the situation described above. The FAA has examined the findings of

the DGAC, reviewed all available information, and determined that AD

action is necessary for products of this type design that are

certificated for operation in the United States.

Explanation of Requirements of Rule

Since an unsafe condition has been identified that is likely to

exist or develop on other airplanes of the same type design registered

in the United States, this AD will require a one-time inspection of the

attachment bolts and washers for the forward cargo container and pallet

latches in the aft cargo compartment to determine if bolts and washers

having the correct part numbers are installed; and replacement of the

bolts and washers with parts having the correct part numbers, if

necessary. The one-time inspection is required to be accomplished in

accordance with the AOT described previously.

This AD also requires revising the Limitations Sections of the FAA-

approved Airplane Flight Manual (AFM), AFM Supplements, and Airplane

Weight and Balance Supplements to specify certain cargo loading

procedures. Accomplishment of the one-time inspection and any necessary

corrective action terminates the requirement for revising the AFM, AFM

Supplements, and Airplane Weight and Balance Supplements.

Determination of Rule's Effective Date

Since a situation exists that requires the immediate adoption of

this regulation, it is found that notice and opportunity for prior

public comment hereon are impracticable, and that good cause exists for

making this amendment effective in less than 30 days.

Comments Invited

Although this action is in the form of a final rule that involves

requirements affecting flight safety and, thus, was not preceded by

notice and an opportunity for public comment, comments are invited on

this rule. Interested persons are invited to comment on this rule by

submitting such written data, views, or arguments as they may desire.

Communications shall identify the Rules Docket number and be submitted

in triplicate to the address specified under the caption ADDRESSES. All

communications received on or before the closing date for comments will

be considered, and this rule may be amended in light of the comments

received. Factual information that supports the commenter's ideas and

suggestions is extremely helpful in evaluating the effectiveness of the

AD action and determining whether additional rulemaking action would be

needed.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the rule that might

suggest a need to modify the rule. All comments submitted will be

available, both before and after the closing date for comments, in the

Rules Docket for examination by interested persons. A report that

summarizes each FAA-public contact concerned with the substance of this

AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this rule must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket Number 96-NM-247-AD.'' The postcard will be date stamped and

returned to the commenter.

Regulatory Impact

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

The FAA has determined that this regulation is an emergency

regulation that must be issued immediately to correct an unsafe

condition in aircraft, and that it is not a ``significant regulatory

action'' under Executive Order 12866. It has been determined further

that this action involves an emergency regulation under DOT Regulatory

Policies and Procedures (44 FR 11034, February 26, 1979). If it is

determined that this emergency regulation otherwise would be

significant under DOT Regulatory Policies and Procedures, a final

regulatory evaluation will be prepared and placed in the Rules Docket.

A copy of it, if filed, may be obtained from the Rules Docket at the

location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

98-01-20 Airbus Industrie: Amendment 39-10282. Docket 96-NM-247-AD.

Applicability: Model A310 and A300-600 airplanes on which Airbus

Modification 6919 or 11849 has not been accomplished; certificated

in any category.

Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

otherwise modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must request approval for an

alternative method of compliance in accordance with paragraph (c) of

this AD. The request should include an assessment of the effect of

the modification, alteration, or repair on the unsafe condition

addressed by this AD; and, if the unsafe condition has not been

eliminated, the request should include specific proposed actions to

address it.

Compliance: Required as indicated, unless accomplished

previously.

To prevent cargo from shifting in flight, and consequent

structural damage and reduced controllability of the airplane,

accomplish the following:

(a) Within 5 days after the effective date of this AD: Revise

the Limitations Section of all FAA-approved Airplane Flight Manuals

(AFM) and AFM Supplements, and the Limitations Section of all FAA-

approved Airplane Weight and Balance Supplements, to include the

following information for loading of cargo containers or pallets in

the aft cargo compartment. This may be accomplished by inserting a

copy of this AD in all AFM's, AFM Supplements, and Weight and

Balance Supplements.

``Limitations

Do not load cargo in the most forward position in the lower deck

aft cargo compartment, just aft of frame 54. Additionally, the

second most forward position in the lower deck aft cargo

compartment, if used, must be occupied by Unit Load Devices (ULD's)

over the full width.

If half size ULD's are loaded in the aft cargo compartment, the

following loading procedure may be accomplished:

On both the left and right sides of the aft cargo compartment,

the most forward position and the second most forward position must

be either both loaded or both empty. In the case where these

positions are empty, all aft cargo compartment latches must be

raised.''

(b) Within 1,000 flight hours after the effective date of this

AD, perform a one-time inspection of the attachment bolts and

washers for the forward cargo container and pallet latches in the

aft cargo compartment to determine if bolts and washers having the

correct part numbers are installed, in accordance with Airbus All

Operator Telex (AOT) 25 05, Revision 03, dated June 25, 1997. If any

discrepancy is found, prior to further flight, accomplish corrective

action in accordance with the AOT. Accomplishment of this

inspection, and corrective action, if necessary, constitutes

terminating action for the requirement of paragraph (a) of this AD;

after these actions are accomplished, the previously required AFM

limitation may be removed from the AFM and AFM supplements.

(c) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, International Branch, ANM-116, FAA,

Transport Airplane Directorate. Operators shall submit their

requests through an appropriate FAA Principal Maintenance Inspector,

who may add comments and then send it to the Manager, International

Branch, ANM-116.

Note 2: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the International Branch, ANM-116.

(d) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished.

(e) The one-time inspection shall be done in accordance with

Airbus All Operator Telex (AOT) 25 05, Revision 03, dated June 25,

1997. This incorporation by reference was approved by the Director

of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR

part 51. Copies may be obtained from Airbus Industrie, 1 Rond Point

Maurice Bellonte, 31707 Blagnac Cedex, France. Copies may be

inspected at the FAA, Transport Airplane Directorate, 1601 Lind

Avenue, SW., Renton, Washington; or at the Office of the Federal

Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

Note 3: The subject of this AD is addressed in French

airworthiness directive 97-143-227(B), dated July 2, 1997.

(f) This amendment becomes effective on January 27, 1998.

Issued in Renton, Washington, on December 31, 1997.

Darrell M. Pederson,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 98-316 Filed 1-9-98; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.