Airworthiness Directives; Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 Series Airplanes

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 62 › 62 FR 1044

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 96-NM-88-AD; Amendment 39-9869; AD 96-26-05]

RIN 2120-AA64

Airworthiness Directives; Fokker Model F27 Mark 100, 200, 300,

400, 500, 600, and 700 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),

applicable to all Fokker Model F27 Mark 100, 200, 300, 400, 500, 600,

and 700 series airplanes, that requires an inspection to detect

cracking of the torque tube assembly of the left-hand (LH) elevator and

surrounding structure; and to detect loose or sheared rivets in that

assembly. This amendment also requires either replacement or repair of

discrepant parts, as appropriate. This amendment is prompted by a

report of fatigue cracking found on the torque tube support of the LH

elevator. The actions specified by this AD are intended to ensure that

cracking is detected and corrected in a timely manner so as to prevent

failure of the torque tube or its support structure, which could result

in reduced controllability of the airplane.

DATES: Effective February 12, 1997.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of February 12, 1997.

ADDRESSES: The service information referenced in this AD may be

obtained from Fokker Aircraft USA, Inc., 1199 North Fairfax Street,

Alexandria, Virginia 22314. This information may be examined at the

Federal Aviation Administration (FAA), Transport

Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton,

Washington; or at the Office of the Federal Register, 800 North Capitol

Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Ruth Harder, Aerospace Engineer,

Standardization Branch, ANM-113, FAA, Transport Airplane Directorate,

1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206)

227-1721; fax (206) 227-1149.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal

Aviation Regulations (14 CFR part 39) to include an airworthiness

directive (AD) that is applicable to all Fokker Model F27 Mark 100,

200, 300, 400, 500, 600, and 700 series airplanes was published in the

Federal Register on September 13, 1996 (61 FR 48439). That action

proposed to require a one-time inspection to detect fatigue cracking of

the torque tube of the left-hand (LH) elevator and its surrounding

structure, and repair, if necessary. That action also proposed to

require an inspection to detect loose or sheared rivets of the same

torque tube assembly, and replacement with serviceable rivets, if

necessary.

Interested persons have been afforded an opportunity to participate

in the making of this amendment. No comments were submitted in response

to the proposal or the FAA's determination of the cost to the public.

Conclusion

The FAA has determined that air safety and the public interest

require the adoption of the rule as proposed.

Cost Impact

The FAA estimates that 34 Fokker Model F27 Mark 100, 200, 300, 400,

500, 600, and 700 series airplanes of U.S. registry will be affected by

this AD, that it will take approximately 4 work hours per airplane to

accomplish the required actions, and that the average labor rate is $60

per work hour. Based on these figures, the cost impact of the AD on

U.S. operators is estimated to be $8,160, or $240 per airplane.

The cost impact figure discussed above is based on assumptions that

no operator has yet accomplished any of the requirements of this AD

action, and that no operator would accomplish those actions in the

future if this AD were not adopted.

Should an operator be required to replace the torque tube assembly

of the LH elevator, the FAA estimates that it will take approximately 2

work hours per airplane to accomplish, and that the average labor rate

is $60 per work hour. Replacement of the assembly will cost

approximately $1,500 per airplane. Based on these figures, the cost

impact of the replacement is estimated to be $1,620 per airplane.

Regulatory Impact

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is

not a ``significant regulatory action'' under Executive Order 12866;

(2) is not a ``significant rule'' under DOT Regulatory Policies and

Procedures (44 FR 11034, February 26, 1979); and (3) will not have a

significant economic impact, positive or negative, on a substantial

number of small entities under the criteria of the Regulatory

Flexibility Act. A final evaluation has been prepared for this action

and it is contained in the Rules Docket. A copy of it may be obtained

from the Rules Docket at the location provided under the caption

ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

96-26-05 Fokker: Amendment 39-9869. Docket 96-NM-88-AD.

Applicability: All Model F27 Mark 100, 200, 300, 400, 500, 600,

and 700 series airplanes, certificated in any category.

Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must request approval for an

alternative method of compliance in accordance with paragraph (d) of

this AD. The request should include an assessment of the effect of

the modification, alteration, or repair on the unsafe condition

addressed by this AD; and, if the unsafe condition has not been

eliminated, the request should include specific proposed actions to

address it.

Compliance: Required as indicated, unless accomplished

previously.

To ensure that cracking is detected and corrected in a timely

manner so as to prevent failure of the torque tube of the left-hand

(LH) elevator or its support structure, which could result in

reduced controllability of the airplane, accomplish the following:

(a) Prior to the accumulation of 45,000 total flight cycles, or

within 4 months after the effective date of this AD, whichever

occurs later, perform an inspection to detect cracking of the torque

tube assembly and the surrounding structure of the LH elevator, and

to detect any loose or sheared rivets of that assembly, in

accordance with ``Part 1'' of the Accomplishment Instructions of

Fokker Service Bulletin F27/55-66, dated December 21, 1994.

(b) If no cracking is detected, and if no loose or sheared rivet

is detected, during the inspection required by paragraph (a) of this

AD: No further action is required by this AD.

(c) If any discrepancy is detected during the inspection

required by paragraph (a) of this AD: Accomplish the applicable

requirements of paragraph (c)(1), (c)(2), or (c)(3) of this AD at

the time specified in that paragraph, and in accordance with Fokker

Service Bulletin F27/55-66, dated December 21, 1994.

(1) If any cracking of the torque tube is detected, or if any

loose or sheared rivet is detected: Prior to further flight, replace

the discrepant part(s) in accordance with ``Part 2,'' paragraph A.,

of the Accomplishment Instructions of the service bulletin.

Note 2: Fokker Service Bulletin F27/55-66 references Fokker

Service Bulletin F27/55-40 as an additional source of service

information for procedures to replace the torque tube assembly with

a serviceable assembly.

(2) If any cracking of the rib at station 300 is detected: Prior

to further flight, repair in accordance with ``Part 2,'' paragraph

B., of the Accomplishment Instructions of the service bulletin.

(3) If any cracking in the torque tube support is detected:

Prior to further flight, accomplish the requirements of either

paragraph (c)(3)(i) or (c)(3)(ii) of this AD, as applicable.

(i) If the crack length does not exceed 30 mm, stop drill the

crack and, thereafter, repeat the inspection specified in paragraph

(a) of this AD at intervals not to exceed 50 flight hours, in

accordance with ``Part 2,'' paragraph C., of the Accomplishment

Instructions of the service bulletin.

(ii) If the crack length exceeds 30 mm, repair in accordance

with a method approved by the Manager, Standardization Branch, ANM-

113.

(d) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Standardization Branch, ANM-113,

FAA, Transport Airplane Directorate. Operators shall submit their

requests through an appropriate FAA Principal Maintenance Inspector,

who may add comments and then send it to the Manager,

Standardization Branch, ANM-113.

Note 3: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Standardization Branch, ANM-113.

(e) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished.

(f) The actions shall be done in accordance with Fokker Service

Bulletin F27/55-66, dated December 21, 1994. This incorporation by

reference was approved by the Director of the Federal Register in

accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be

obtained from Fokker Aircraft USA, Inc., 1199 North Fairfax Street,

Alexandria, Virginia 22314. Copies may be inspected at the FAA,

Transport Airplane Directorate, Alexandria, Virginia 22314. Copies

may be inspected at the FAA, Transport Airplane Directorate, 1601

Lind Avenue, SW., Renton, Washington; or at the Office of the

Federal Register, 800 North Capitol Street, NW., suite 700,

Washington, DC.

(g) This amendment becomes effective on February 12, 1997.

Issued in Renton, Washington, on December 23, 1996.

Darrell M. Pederson,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 97-476 Filed 1-7-97; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.

Airworthiness Directives; Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 Series Airplanes · 62 FR 1044 | Frix