Airworthiness Directives; General Electric Company CF6-80C2 Series Turbofan Engines

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 64 › 64 FR 749

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 98-ANE-75-AD; Amendment 39-10968; AD 99-01-01]

RIN 2120-AA64

Airworthiness Directives; General Electric Company CF6-80C2

Series Turbofan Engines

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD) that

is applicable to General Electric Company CF6-80C2 series turbofan

engines. This action requires a one-time visual inspection to ensure

the correct accessory gearbox (AGB) idler adapter inserts are

installed, and, if necessary, removal of AGB idler adapters with the

improper inserts. This amendment is prompted by a report of a failure

of a fuel tube flange connection due to improper AGB idler adapter

inserts that resulted in a high pressure fuel leak and engine fire. The

actions specified in this AD are intended to identify and remove AGB

idler adapters with improper inserts, which can result in an engine

fire and damage to the aircraft.

DATES: Effective January 21, 1999.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of January 21, 1999.

Comments for inclusion in the Rules Docket must be received on or

before March 8, 1999.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), New England Region, Office of the Regional

Counsel, Attention: Rules Docket No. 98-ANE-75-AD, 12 New England

Executive Park, Burlington, MA 01803-5299. Comments may also be sent

via the Internet using the following address: ``9-ad-

[email protected]''. Comments sent via the Internet must contain the

docket number in the subject line.

The service information referenced in this AD may be obtained from

General Electric Aircraft Engines, c/o Commercial Technical

Publications, 1 Neumann Way, Rm. 230, Cincinnati, OH 45215-1988;

telephone (513) 552-2005, fax (513) 552-2816. This information may be

examined at the FAA, New England Region, Office of the Regional

Counsel, 12 New England Executive Park, Burlington, MA; or at the

Office of the Federal Register, 800 North Capitol Street, NW., suite

700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Ian Dargin, Aerospace Engineer, Engine

Certification Office, FAA, Engine and Propeller Directorate, 12 New

England Executive Park, Burlington, MA 01803-5299; telephone (781) 238-

7178, fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: The Federal Aviation Administration (FAA)

has received a report of an engine fire on an Airbus A300 aircraft with

General Electric Company (GE) Model CF6-80C2A5 turbofan engines

installed. The investigation into the cause of the fire identified a

high pressure fuel leak at the fuel cross-over tube to accessory

gearbox (AGB) idler adapter flange interface. The fuel leak occurred

due to shearing of the idler adapter threads by the threaded inserts,

allowing the inserts to pull out. This was attributed to incorrect

Service Bulletin (SB) instructions which created a situation where a

repair station installed improper inserts into the AGB idler adapter

housing at a previous maintenance shop visit.

The maintenance on the idler adapter was performed using GE SB 72-

743, dated August 25, 1994, that provided instructions for AGB idler

adapter rework on P/N 9395M78G06 adapters to improve the reliability

and correct a fuel leak problem that had been identified on engines in

revenue service. Idler adapters that were reworked were required to be

remarked to P/N 9395M78G08. The instructions in SB 72-743 were

incorrect and could have resulted in repair stations installing

improper inserts into the idler adapter. GE issued supplemental

instructions by way of Repair Document 032-273-S1, dated April 8, 1998,

which addresses the problem in SB 72-743 and has proven to be an

acceptable repair procedure. Furthermore, GE has published SB 72-743,

Revision 1, dated November 2, 1998, to cancel the rework of any AGB

idler adapter in accordance with the original issue of the SB.

Presently, the total number of GE CF6-80C2 engines that have

incorporated SB 72-743 and that could have improper inserts installed

is not known. Therefore, work performed using SB 72-743 by any repair

facility is suspect at this time. This condition, if not corrected, can

result in shearing of the idler adapter threads and pullout of the

threaded inserts from the AGB idler adapter which could result in a

high pressure fuel leak leading to a potential engine fire and damage

to the aircraft.

The FAA has reviewed and approved the technical contents of GE CF6-

80C2 Alert Service Bulletins (ASB) 73-A283, Revision 2, dated November

18, 1998, Revision 1, dated October 30, 1998, and Original, dated

September 18, 1998. These ASBs describe procedures for a one-time

visual inspection on AGB idler adapters, P/N 9395M78G08, that had been

reworked from a P/N 9395M78G06 configuration, to ensure the correct AGB

idler adapter threaded inserts are installed, and if necessary, removal

of AGB idler adapters with the improper inserts.

Since an unsafe condition has been identified that is likely to

exist or develop on other engines of the same type design, this AD is

being issued to prevent an engine fire and damage to the aircraft. This

AD requires a one-time visual inspection to ensure the correct AGB

idler adapter threaded inserts are installed, and if necessary, removal

of the AGB idler adapters with the improper inserts. The actions are

required to be accomplished in accordance with the ASB described

previously.

Since a situation exists that requires the immediate adoption of

this regulation, it is found that notice and opportunity for prior

public comment hereon are impracticable, and that good cause exists for

making this amendment effective in less than 30 days.

Comments Invited

Although this action is in the form of a final rule that involves

requirements affecting flight safety and, thus, was not preceded by

notice and an opportunity for public comment, comments are invited on

this rule. Interested persons are invited to comment on this rule by

submitting such written data, views, or arguments as they may desire.

Communications should identify the Rules Docket number and be submitted

in triplicate to the address specified under the caption ADDRESSES. All

communications received on or before the closing date for comments will

be considered, and this rule may be amended in light of the comments

received. Factual information that supports the commenter's ideas and

suggestions is extremely helpful in evaluating the effectiveness of the

AD action and determining whether additional rulemaking action would be

needed.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the rule that might

suggest a need to modify the rule. All comments submitted will be

available, both before and after the closing date for comments, in the

Rules Docket for examination by interested persons. A report that

summarizes each FAA-public contact concerned with the substance of this

AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this notice must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket Number 98-ANE-75-AD.'' The postcard will be date stamped and

returned to the commenter.

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

The FAA has determined that this regulation is an emergency

regulation that must be issued immediately to correct an unsafe

condition in aircraft, and is not a ``significant regulatory action''

under Executive Order 12866. It has been determined further that this

action involves an emergency regulation under DOT Regulatory Policies

and Procedures (44 FR 11034, February 26, 1979). If it is determined

that this emergency regulation otherwise would be significant under DOT

Regulatory Policies and Procedures, a final regulatory evaluation will

be prepared and placed in the Rules Docket. A copy of it, if filed, may

be obtained from the Rules Docket at the location provided under the

caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

99-01-01 General Electric Company: Amendment 39-10968 Docket 98-

ANE-75-AD.

Applicability: General Electric Company (GE) CF6-80C2 series

turbofan engines, with Accessory Gearbox (AGB) idler adapters, Part

Number (P/N) 9395M78G08 that had been reworked from a P/N 9395M78G06

configuration using GE CF6-80C2 Service Bulletin (SB) 72-743, dated

August 25, 1994, excluding those parts that were repaired by GE

Repair Document 032-273-S1, dated April 8, 1998. These engines are

installed on but not limited to Airbus A300 and A310 series, and

Boeing 747, 767, and MD-11 aircraft.

Note 1: Methods of determining if a P/N 9395M78G08 AGB idler

adapter had been reworked from a P/N 9395M78G06 configuration

include a record search or a visual inspection of the AGB idler

adapter part number in accordance with GE CF6-80C2 Alert Service

Bulletin (ASB) 73-A283, Revision 2, dated November 18, 1998,

Revision 1, dated October 30, 1998, or Original, dated September 18,

1998.

Note 2: This airworthiness directive (AD) applies to each engine

identified in the preceding applicability provision, regardless of

whether it has been modified, altered, or repaired in the area

subject to the requirements of this AD. For engines that have been

modified, altered, or repaired so that the performance of the

requirements of this AD is affected, the owner/operator must request

approval for an alternative method of compliance in accordance with

paragraph (c) of this AD. The request should include an assessment

of the effect of the modification, alteration, or repair on the

unsafe condition addressed by this AD; and, if the unsafe condition

has not been eliminated, the request should include specific

proposed actions to address it.

Compliance: Required as indicated, unless accomplished

previously.

To prevent an engine fuel leak, which can result in an engine

fire and damage to the aircraft, accomplish the following:

(a) Within 10 days after the effective date of this AD:

(1) Perform a visual inspection of AGB idler adapter inserts in

accordance with paragraph (2)(B) of the Accomplishment Instructions

of GE CF6-80C2 ASB 73-A283, Revision 2, dated November 18, 1998,

Revision 1, dated October 30, 1998, or Original, dated September 18,

1998.

(2) Remove the AGB adapter from service and replace with a

serviceable part those adapters with one or more inserts that are

flush with or extend past the back face of the casting.

(b) For the purpose of this AD, a serviceable part is defined as

any AGB idler adapter, except for P/Ns 9395M78G08 that had been

reworked from a P/N 9395M78G06 configuration having one or more

inserts flush with or extended past the back face of the casting, as

described in GE CF6-80-C2 ASB 73-A283, Revision 2, dated November

18, 1998, Revision 1, dated October 30, 1998, or Original, dated

September 18, 1998.

(c) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Engine Certification Office.

Operators shall submit their requests through an appropriate FAA

Principal Maintenance Inspector, who may add comments and then send

it to the Manager, Engine Certification Office.

Note 3: Information concerning the existence of approved

alternative methods of compliance with this airworthiness directive,

if any, may be obtained from the Engine Certification Office.

(d) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the aircraft to a location where

the requirements of this AD can be accomplished.

(e) The actions required by this AD shall be done in accordance

with the following GE CF6-80C2 ASBs:

----------------------------------------------------------------------------------------------------------------

Document No. Pages Revision Date

----------------------------------------------------------------------------------------------------------------

73-A283........................ 1.................... 2.................... November 18, 1998.

2-4.................. 1.................... October 30, 1998.

5.................... Original............. September 18, 1998.

6-27................. 1.................... October 30, 1998.

Total pages: 27.

73-A283........................ 1-4.................. 1.................... October 30, 1998.

5.................... Original............. September 18, 1998.

6-27................. 1.................... October 30, 1998.

Total pages: 27

73-A283........................ 1-9.................. Original............. September 18, 1998.

Total pages: 9.............

----------------------------------------------------------------------------------------------------------------

This incorporation by reference was approved by the Director of the

Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part

51. Copies may be obtained from General Electric Aircraft Engines,

c/o Commercial Technical Publications, 1 Neumann Way, Rm. 230,

Cincinnati, OH 45215-1988; telephone (513) 552-2005, fax (513) 552-

2816. Copies may be inspected at the FAA, New England Region, Office

of the Regional Counsel, 12 New England Executive Park, Burlington,

MA; or at the Office of the Federal Register, 800 North Capitol

Street, NW., suite 700, Washington, DC.

(f) This amendment becomes effective on January 21, 1999.

Issued in Burlington, Massachusetts, on December 23, 1998.

David A. Downey,

Assistant Manager, Engine and Propeller Directorate, Aircraft

Certification Service.

[FR Doc. 99-10 Filed 1-5-99; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.

Airworthiness Directives; General Electric Company CF6-80C2 Series Turbofan Engines · 64 FR 749 | Frix