Airworthiness Directives; The Uninsured Relative Workshop Inc. Vector Parachute Systems

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 64 › 64 FR 751

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 98-CE-101-AD; Amendment 39-10977; AD 99-01-11]

RIN 2120-AA64

Airworthiness Directives; The Uninsured Relative Workshop Inc.

Vector Parachute Systems

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD) that

applies to all The Uninsured Relative Workshop Inc. (doing business as

and referred to herein as Relative Workshop) vector parachute systems

that were manufactured between January 1, 1996, and September 10, 1998.

This AD requires inspecting the amp fittings on the end of the

breakaway housing for proper swaging, and re-swaging any incorrectly

swaged fittings using the Nicopress or Swage-It swaging

tool. This AD is the result of a quality control problem on Relative

Workshop vector parachute systems. In particular, a loose amp fitting

was found on the breakaway housing during packing of one of these

vector parachute systems. Further analysis reveals that the amp

fittings on the end of the stainless steel breakaway housing were

improperly swaged, and that this condition could exist on any of the

2,127 parachute systems that were manufactured during the above-

referenced time period. The actions specified by this AD are intended

to prevent the amp fittings from coming off the stainless steel

breakaway housing, which could result in an unintentional partial

breakaway of the main chute and interference with the deployment of the

reserve parachute.

DATES: Effective January 29, 1999.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of January 29, 1999.

Comments for inclusion in the Rules Docket must be received on or

before February 26, 1999.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), Central Region, Office of the Regional Counsel,

Attention: Rules Docket No. 98-CE-101-AD, Room 1558, 601 E. 12th

Street, Kansas City, Missouri 64106.

Service information that applies to this AD may be obtained from

Relative Workshop, 1645 North Lexington Avenue, DeLand, Florida 32724;

telephone: (904) 736-7589; facsimile: (904) 734-7537. This information

may also be examined at the Federal Aviation Administration (FAA),

Central Region, Office of the Regional Counsel, Attention: Rules Docket

No. 98-CE-101-AD, Room 1558, 601 E. 12th Street, Kansas City, Missouri

64106; or at the Office of the Federal Register, 800 North Capitol

Street, NW, suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Donald J. Young, Aerospace Engineer,

FAA, Atlanta Aircraft Certification Office, One Crown Center, 1895

Phoenix Boulevard, suite 450, Atlanta, Georgia 30349; telephone: (770)

703-6079; facsimile: (770) 703-6097.

SUPPLEMENTARY INFORMATION:

Discussion

The FAA has received information regarding a quality control

problem on Relative Workshop vector parachute systems. A loose amp

fitting on the breakaway housing was found during packing of one of

these Relative Workshop vector parachute systems. Further analysis

reveals that the amp fittings on the end of the stainless steel

breakaway housing were improperly swaged. This problem could exist on

any of the 2,127 Relative Workshop vector parachute system that were

manufactured between January 1, 1996, and September 10, 1998.

This condition, if not detected and corrected in a timely manner,

could result in an unintentional partial breakaway of the main chute

and

interference with deployment of the reserve parachute.

Relevant Service Information

Relative Workshop has issued Product Service Bulletin #091098-B,

dated September 10, 1998, which specifies procedures for inspecting the

amp fittings on the end of the breakaway housing for proper swaging,

and re-swaging any incorrectly swaged fittings using the

Nicopress or Swage-It swaging tool.

The FAA's Determination

After examining the circumstances and reviewing all available

information related to the incident described above, including the

above-referenced service information, the FAA has determined that AD

action should be taken to prevent the amp fittings from coming off the

stainless steel breakaway housing, which could result in an

unintentional partial breakaway of the main chute and interference with

the deployment of the reserve parachute.

Explanation of the Provisions of the AD

Since an unsafe condition has been identified that is likely to

exist or develop in other The Uninsured Relative Workshop Inc. vector

parachute systems that were manufactured between January 1, 1996, and

September 10, 1998, the FAA is issuing an AD. This AD requires

inspecting the amp fittings on the end of the breakaway housing for

proper swaging, and re-swaging any incorrectly swaged fittings using

the Nicopress or Swage-It swaging tool. Accomplishment of the

actions specified in this AD is required in accordance with Relative

Workshop Product Service Bulletin #091098-B, dated September 10, 1998.

Determination of the Effective Date of the AD

Since a situation exists that requires the immediate adoption of

this regulation, it is found that notice and opportunity for public

prior comment hereon are impracticable, and that good cause exists for

making this amendment effective in less than 30 days.

Comments Invited

Although this action is in the form of a final rule that involves

requirements affecting immediate flight safety and, thus, was not

preceded by notice and opportunity to comment, comments are invited on

this rule. Interested persons are invited to comment on this rule by

submitting such written data, views, or arguments as they may desire.

Communications should identify the Rules Docket number and be submitted

in triplicate to the address specified above. All communications

received on or before the closing date for comments will be considered,

and this rule may be amended in light of the comments received. Factual

information that supports the commenter's ideas and suggestions is

extremely helpful in evaluating the effectiveness of the AD action and

determining whether additional rulemaking action would be needed.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the rule that might

suggest a need to modify the rule. All comments submitted will be

available, both before and after the closing date for comments, in the

Rules Docket for examination by interested persons. A report that

summarizes each FAA-public contact concerned with the substance of this

AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this rule must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket No. 98-CE-101-AD.'' The postcard will be date stamped and

returned to the commenter.

Regulatory Impact

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

The FAA has determined that this regulation is an emergency

regulation that must be issued immediately to correct an unsafe

condition in parachutes, and is not a significant regulatory action

under Executive Order 12866. It has been determined further that this

action involves an emergency regulation under DOT Regulatory Policies

and Procedures (44 FR 11034, February 26, 1979). If it is determined

that this emergency regulation otherwise would be significant under DOT

Regulatory Policies and Procedures, a final regulatory evaluation will

be prepared and placed in the Rules Docket (otherwise, an evaluation is

not required). A copy of it, if filed, may be obtained from the Rules

Docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding a new airworthiness directive

(AD) to read as follows:

99-01-11 The Uninsured Relative Workshop Inc. (doing business as

and referred to herein as Relative Workshop): Amendment 39-10977;

Docket No. 98-CE-101-AD.

Applicability: All Vector II and III Parachute Systems That Were

Manufactured Between January 1, 1996, and September 10, 1998.

Note 1: This AD applies to any parachute system referenced in

the Applicability section of this AD, regardless of whether it has

been modified, altered, or repaired in the area subject to the

requirements of this AD. For those parachute systems that have been

modified, altered, or repaired so that the performance of the

requirements of this AD is affected, the owner/operator must request

approval for an alternative method of compliance in accordance with

paragraph (c) of this AD. The request should include an assessment

of the effect of the modification, alteration, or repair on the

unsafe condition addressed by this AD; and, if the unsafe condition

has not been eliminated, the request should include specific

proposed actions to address it.

Compliance: Required prior to the next jump after the effective

date of this AD, unless already accomplished.

To prevent the amp fittings from coming off the stainless steel

breakaway housing, which could result in an unintentional partial

breakaway of the main chute and interference with the deployment of

the reserve parachute, accomplish the following:

(a) Inspect the amp fittings on the end of the breakaway housing

for proper swaging, and re-swage any incorrectly swaged fittings

using the Nicopress or Swage-It swaging tool. Accomplish these

actions in accordance with Relative Workshop Product Service

Bulletin #091098-B, dated September 10, 1998.

Note 2: The above-referenced service bulletin may be obtained

from the manufacturer at the address in paragraph (d) of this AD or

through the Internet at ``http://www.relativeworkshop.com/''.

(b) As of the effective date of this AD, no person shall put

into service any of the affected parachute systems, unless the

parachute system has been inspected and modified (as necessary), as

specified in paragraph (a) of this AD.

(c) An alternative method of compliance or adjustment of the

compliance time that provides an equivalent level of safety may be

approved by the Manager, Atlanta Aircraft Certification Office

(ACO), One Crown Center, 1895 Phoenix Boulevard, Suite 450, Atlanta,

Georgia 30349. The request shall be forwarded through an appropriate

FAA Maintenance Inspector, who may add comments and then send it to

the Manager, Atlanta ACO.

Note 3: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Atlanta ACO.

(d) The inspection and modification required by this AD shall be

done in accordance with Relative Workshop Product Service Bulletin

#091098-B, dated September 10, 1998. This incorporation by reference

was approved by the Director of the Federal Register in accordance

with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from

Relative Workshop, 1645 North Lexington Avenue, DeLand, Florida

32724. Copies may be inspected at the FAA, Central Region, Office of

the Regional Counsel, Room 1558, 601 E. 12th Street, Kansas City,

Missouri, or at the Office of the Federal Register, 800 North

Capitol Street, NW, suite 700, Washington, DC.

(e) This amendment becomes effective on January 29, 1999.

Issued in Kansas City, Missouri, on December 22, 1998.

Michael Gallagher,

Manager, Small Airplane Directorate, Aircraft Certfication Service.

[FR Doc. 99-142 Filed 1-5-99; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.