Airworthiness Directives; Boeing Model 747 Series Airplanes

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 62 › 62 FR 302

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 96-NM-280-AD; Amendment 39-9868; AD 96-26-52]

RIN 2120-AA64

Airworthiness Directives; Boeing Model 747 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This document publishes in the Federal Register an amendment

adopting Airworthiness Directive (AD) T96-26-52 that was sent

previously to all known U.S. owners and operators of Boeing Model 747

series airplanes by individual telegrams. This AD requires repetitive

inspections of the access doors to the midspar/spring beam fuse pins on

all engine pylons to detect cracks on the external surface; repetitive

inspections of each midspar/spring beam fuse pin to detect if it

protrudes beyond its mating nut by a specified distance; and repair of

any discrepancy found. This action is prompted by a report indicating

that a fuse pin had migrated on an inboard spring beam fitting on the

Number 1 engine pylon of a Boeing Model 747-400 airplane. The actions

specified by this AD are intended to prevent migration of this fuse

pin, which, if not detected and corrected in a timely manner, could

result in failure of the engine pylon and consequent separation of the

engine from the wing.

DATES: Effective January 8, 1997, to all persons except those persons

to whom it was made immediately effective by telegraphic AD T96-26-52,

issued December 20, 1996, which contained the requirements of this

amendment.

Comments for inclusion in the Rules Docket must be received on or

before March 4, 1997.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), Transport Airplane Directorate, ANM-103,

Attention: Rules Docket No. 96-NM-280-AD, 1601 Lind Avenue, SW.,

Renton, Washington 98055-4056.

Service information pertaining to this rulemaking action may be

obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle,

Washington 98124-2207. This information may be examined at the FAA,

Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,

Washington.

FOR FURTHER INFORMATION CONTACT: Tamara L. Dow, Aerospace Engineer,

Airframe Branch, ANM-120S, FAA, 1601 Lind Avenue, SW., Renton,

Washington 98055-4056, telephone (206) 227-2771; fax (206) 227-1181.

SUPPLEMENTARY INFORMATION: On December 20, 1996, the FAA issued

telegraphic AD T96-26-52, which is applicable to certain Boeing Model

747 series airplanes.

That action was prompted by a report indicating that a fuse pin had

migrated \5/8\ inch out of an inboard spring beam fitting on the Number

1 engine pylon of a Boeing Model 747-400 series airplane. In addition,

the mating nut to this pin had backed off approximately \3/10\ inch

from full engagement with the pin. The discrepant fuse pin was detected

after maintenance personnel observed that the access door (part number

65B94112-43) to this fuse pin protruded outward from its adjacent pylon

structure.

At the time this discrepancy was found, the airplane had

accumulated 12,446 total hours time-in-service, and accomplished 1,439

total landings. Prior to delivery of this airplane in June 1994, the

manufacturer had installed fuse pins in the spring beam fitting that

are made of 15-5 corrosion resistant steel (``third generation pins'').

These pins replaced existing pins made of 4330 or 4340 steel.

Migration of the fuse pin, if not detected and corrected in a

timely manner, could result in failure of the engine pylon and

consequent separation of the engine from the wing.

Other Relevant Rulemaking

The FAA previously had issued AD 95-13-05 [amendment 39-9285 (60 FR

33333, dated June 28, 1995; as corrected at 60 FR 35452, July 7,

1995)], which applies to certain Boeing Model 747 series airplanes

equipped with Rolls Royce Model RB211 series engines. The FAA also had

issued AD 95-13-06 [amendment 39-9286 (60 FR 33338, June 28, 1995; as

corrected at 60 FR 37500, July 20, 1995)], which applies to certain

Model 747 series airplanes equipped with General Electric Model CF6-

80C2 series engines or Pratt & Whitney Model PW4000 series engines.

These AD's, which are almost identical, require modification of the

nacelle strut and wing structure of the applicable airplanes. Among the

actions required by both AD's is the installation of a mechanical

secondary retention to prevent the fuse pins for the midspar/spring

beam fittings from migrating.

At the time the discrepancy described above was discovered, the

nacelle strut and wing modification had not yet been accomplished on

the incident airplane;

consequently, the secondary retention device had not yet been installed

either. (The secondary retention device has been installed during

production of airplanes beginning at line number 1047.)

Explanation of Requirements of the Rule

Since the unsafe condition described is likely to exist or develop

on other airplanes of the same type design, the FAA issued Telegraphic

AD T96-26-52 to prevent migration of this fuse pin, subsequent failure

of the engine pylon, and consequent separation of the engine from the

wing. The AD requires repetitive detailed visual inspections of the

access doors to the midspar/spring beam fuse pins on all engine pylons

to detect cracks on the external surface, and repair, if necessary. In

addition, the AD requires repetitive detailed visual inspections of

each midspar/spring beam fuse pin to detect if it protrudes beyond its

mating nut by a specified distance, and repair, if necessary. These

inspections are to be repeated until the terminating modifications

currently required by AD 95-13-05 or AD 95-13-06, as applicable, are

accomplished.

Since it was found that immediate corrective action was required,

notice and opportunity for prior public comment thereon were

impracticable and contrary to the public interest, and good cause

existed to make the AD effective immediately by individual telegrams

issued on December 20, 1996, to all known U.S. owners and operators of

Boeing Model 747 series airplanes. These conditions still exist, and

the AD is hereby published in the Federal Register as an amendment to

section 39.13 of the Federal Aviation Regulations (14 CFR 39.13) to

make it effective to all persons.

Comments Invited

Although this action is in the form of a final rule that involves

requirements affecting flight safety and, thus, was not preceded by

notice and an opportunity for public comment, comments are invited on

this rule. Interested persons are invited to comment on this rule by

submitting such written data, views, or arguments as they may desire.

Communications shall identify the Rules Docket number and be submitted

in triplicate to the address specified under the caption ADDRESSES. All

communications received on or before the closing date for comments will

be considered, and this rule may be amended in light of the comments

received. Factual information that supports the commenter's ideas and

suggestions is extremely helpful in evaluating the effectiveness of the

AD action and determining whether additional rulemaking action would be

needed.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the rule that might

suggest a need to modify the rule. All comments submitted will be

available, both before and after the closing date for comments, in the

Rules Docket for examination by interested persons. A report that

summarizes each FAA-public contact concerned with the substance of this

AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this rule must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket Number 96-NM-280-AD.'' The postcard will be date stamped and

returned to the commenter.

Regulatory Impact

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

The FAA has determined that this regulation is an emergency

regulation that must be issued immediately to correct an unsafe

condition in aircraft, and that it is not a ``significant regulatory

action'' under Executive Order 12866. It has been determined further

that this action involves an emergency regulation under DOT Regulatory

Policies and Procedures (44 FR 11034, February 26, 1979). If it is

determined that this emergency regulation otherwise would be

significant under DOT Regulatory Policies and Procedures, a final

regulatory evaluation will be prepared and placed in the Rules Docket.

A copy of it, if filed, may be obtained from the Rules Docket at the

location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

96-26-52 Boeing: Amendment 39-9868. Docket 96-NM-280-AD.

Applicability: Model 747 series airplanes having line numbers 1

through 1046, inclusive; certificated in any category; that meet all

of the following criteria:

equipped with Pratt & Whitney Model PW4000 series

engines, or General Electric Model CF6-80C2 series engines, or Rolls

Royce Model RB211 series engines;

on which fuse pins having part numbers 310U2301-101, -

116, -117, or -120 (``third generation'' fuse pins) are installed at

the midspar/spring beam fittings of the engine pylon; and

on which the modification of the nacelle strut and wing

structure in accordance with Boeing Alert Service Bulletin 747-

54A2156 or Boeing Alert Service Bulletin 747-54A2157, as applicable,

has not been accomplished.

Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

otherwise modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must request approval for an

alternative method of compliance in accordance with paragraph (c) of

this AD. The request should include an assessment of the effect of

the modification, alteration, or repair on the unsafe condition

addressed by this AD; and, if the unsafe condition has not been

eliminated, the request should include specific proposed actions to

address it.

Compliance: Required as indicated, unless accomplished

previously.

To prevent failure of the engine pylon and consequent separation

of the engine from the wing, due to migration of the fuse pins

installed at the midspar/spring beam fittings of the pylon,

accomplish the following:

(a) Within 15 days after the receipt of this AD, accomplish the

requirements of paragraphs (a)(1) and (a)(2) of this AD.

(1) Perform a detailed visual inspection of the access doors to

each midspar/spring beam fuse pin on each engine pylon to detect

cracks on the external surface of the doors.

(i) If no cracking is detected during the inspection, repeat

that inspection at intervals not to exceed 150 landings or 1,000

hours time-in-service, whichever occurs first.

(ii) If any cracking is detected during the inspection, prior to

further flight, repair in accordance with a method approved by the

Manager, Seattle Aircraft Certification Office

(ACO), FAA, Transport Airplane Directorate. Thereafter, repeat the

inspection at intervals not to exceed 150 landings or 1,000 hours

time-in-service, whichever occurs first.

(2) Gain access through the aft fairing doors of each engine

pylon to each midspar/spring beam fuse pin and its mating, self-

locking nut, and perform a detailed visual inspection of each fuse

pin to verify that at least one thread of the fuse pin protrudes

beyond its mating, self-locking nut.

(i) If no discrepancy is detected during the inspection, repeat

that inspection at intervals not to exceed 150 landings or 1,000

hours time-in-service, whichever occurs first.

(ii) If the inspection reveals that at least one thread does not

protrude beyond its mating, self-locking nut, prior to further

flight, repair in accordance with a method approved by the Manager,

Seattle ACO, FAA, Transport Airplane Directorate. Thereafter, repeat

the inspection at intervals not to exceed 150 landings or 1,000

hours time-in-service, whichever occurs first.

(b) Accomplishment of the modification of the nacelle strut and

wing structure in accordance with Boeing Alert Service Bulletin 747-

54A2156, Revision 2, dated December 21, 1995, or earlier revisions

(for airplanes equipped with General Electric Model CF6-80C2 series

engines, or Pratt & Whitney PW4000 series engines); or Boeing Alert

Service Bulletin 747-54A2157, Revision 2, dated November 14, 1996,

or earlier revisions (for airplanes with Rolls Royce Model RB211

series engines); as applicable; constitutes terminating action for

the repetitive detailed visual inspections required by paragraphs

(a)(1) and (a)(2) of this AD.

(c) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Seattle ACO, FAA, Transport

Airplane Directorate. Operators shall submit their requests through

an appropriate FAA Principal Maintenance Inspector, who may add

comments and then send it to the Manager, Seattle ACO.

Note 2: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Seattle ACO.

(d) Special flight permits may be issued in accordance with

Sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished.

(e) This amendment becomes effective on January 8, 1997, to all

persons except those persons to whom it was made immediately

effective by telegraphic AD T96-26-52, issued on December 20, 1996,

which contained the requirements of this amendment.

Issued in Renton, Washington, on December 23, 1996.

S. R. Miller,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 97-114 Filed 1-2-97; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.