Airworthiness Directives; Hamilton Standard Propellers Models 14RF-9, 14RF-19, 14RF-21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF- 15, 14SF-17, 14SF-19, and 14SF-23; and Hamilton Standard/British Aerospace 6/5500/F

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 61 › 61 FR 617

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 95-ANE-73; Amendment 39-9477, AD 96-01-01]

Airworthiness Directives; Hamilton Standard Propellers Models

14RF-9, 14RF-19, 14RF-21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF-

15, 14SF-17, 14SF-19, and 14SF-23; and Hamilton Standard/British

Aerospace 6/5500/F

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD) that

is applicable to Hamilton Standard Propeller Models 14RF-9, 14RF-19,

14RF-21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF-15, 14SF-17, 14SF-

19, and 14SF-23; and Hamilton Standard/British Aerospace 6/5500/F. This

action supersedes priority letter AD 95-18-06R1, that was issued on

August 30, 1995, that currently requires ultrasonic shear wave

inspection on all Hamilton Standard 14RF-9 propeller blades, and

ultrasonic shear wave inspection on certain Hamilton Standard Propeller

Models 14RF-19, 14RF-21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF-15,

14SF-17, 14SF-19, and 14SF-23; and Hamilton Standard/British Aerospace

6/5500/F propeller blades. This action requires that all blades of

applicable Hamilton Standard propellers be calibrated for ultrasonic

transmissibility before conducting the ultrasonic shear wave

inspection. This action improves the crack detection capability of the

ultrasonic shear wave inspection. This action also decreases the

repetitive inspection interval for the 14RF-9, 14SF-5, -7, -11, -15, -

17, -19, and -23 from 1,250 flight cycles to 500 flight cycles. This

action also establishes a new ultrasonic shear wave inspection interval

of 1,000 flight cycles for the 14RF-19 and 2,500 flight cycles for the

14RF-21 and the 6/5500/F. This AD also removes 14SFL11 propellers from

service. This AD is prompted by reports that the existing ultrasonic

shear wave inspection may not detect cracks as originally determined

with some blades due to geometric differences. The actions specified by

this AD are intended to prevent separation of a propeller blade due to

cracks initiating in the blade taper bore, that can result in aircraft

damage, and possible loss of the aircraft.

DATES: Effective January 19, 1996.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of January 19, 1996.

Comments for inclusion in the Rules Docket must be received on or

before January 29, 1996.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), New England Region, Office of the Assistant Chief

Counsel, Attention: Rules Docket No. 95-ANE-73, 12 New England

Executive Park, Burlington, MA 01803-5299.

The service information referenced in this AD may be obtained from

Hamilton Standard, One Hamilton Road, Windsor Locks, CT 06096-1010;

telephone (203) 654-6876. This information may be examined at the FAA,

New England Region, Office of the Assistant Chief Counsel, 12 New

England Executive Park, Burlington, MA; or at the Office of the Federal

Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Frank Walsh, Aerospace Engineer,

Boston Aircraft Certification Office, FAA, Engine & Propeller

Directorate, 12 New England Executive Park, Burlington, MA 01803,

telephone (617) 238-7152, fax: (617) 238-7199.

SUPPLEMENTARY INFORMATION: On August 30, 1995, the Federal Aviation

Administration (FAA) issued priority letter airworthiness directive

(AD) 95-18-06R1 applicable to Hamilton Standard Propeller Models 14RF-

9, 14RF-19, 14RF-21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF-15,

14SF-17, 14SF-19, and 14SF-23; and Hamilton Standard/British Aerospace

6/5500/F propellers, which requires ultrasonic shear wave inspection on

all Hamilton Standard 14RF-9 propeller blades, and ultrasonic shear

wave inspection on certain Hamilton Standard Models 14RF-19, -21; and

14SF-5, -7, -11, L11, -15, -17, -19, and -23; and Hamilton Standard/

British Aerospace 6/5500/F propeller blades. That AD action was

prompted by a report of a Hamilton Standard 14RF-9 propeller blade

installed on an Embraer EMB-120 aircraft that had separated inflight.

Since the issuance of that priority letter AD, the FAA and Hamilton

Standard have been working to improve the crack detection capability of

the ultrasonic inspection method as well as working to refine the crack

growth rate prediction methodology. The results of this work form the

basis for the new inspection method and the change in repetitive

inspection interval. This AD will require that propeller blades be

calibrated for ultrasonic transmissibility before conducting an

ultrasonic shear wave inspection, thereby improving the detection

capability of the ultrasonic shear wave inspection technique. This

action will also decrease the repetitive inspection interval for the

14RF-9, 14SF-5, -7, -11, -15, -17, -19, and -23 from 1,250 flight

cycles to 500 flight cycles. This action will further establish a new

ultrasonic shear wave inspection interval of 1,000 flight cycles for

the 14RF-19 and 2,500 flight cycles for the 14RF-21 and the 6/5500/F

propeller models. This AD also requires removal of the life limited

14SFL11 propellers currently in service, approximately four propellers.

These 14SFL11 propellers will be replaced with the Hamilton Standard

Model 247F propellers. The actions specified by this AD are intended to

prevent the separation of a propeller blade due to cracks initiating in

the blade taper bore, that can result in aircraft damage, and possible

loss of aircraft control.

This AD references two ultrasonic inspection methods, one that can

be accomplished without removing the lead from the taper bore which

permits an on wing inspection and a second inspection that requires the

blade be removed and inspected at an FAA approved facility. The

inspection that is conducted without removing the lead from the taper

bore cannot be accomplished on some blades because of ultrasonic

transmissibility problems caused by the lead wool absorbing the signal.

These blades must be removed and inspected at an FAA approved facility

where the lead wool will be extracted.

The FAA has reviewed and approved the technical contents of the

following Hamilton Standard Alert Service Bulletins (ASB's): No. 14RF-

9-61-A91, No. 14RF-19-61-A55, No. 14RF-21-61-A73, No. 14SF-61-A93, and

No. 6/5500/F-61-A41, all dated December 7, 1995, and No. 14RF-9-61-A91,

Rev 1, No. 14RF-19-61-A55, Rev 1, No. 14RF-21-61-A73, Rev 1, No. 14SF-

61-A93, Rev 1, and No. 6/5500/F-61-A41, Rev 1, all dated December 15,

1995, that describe procedures for ultrasonic shear wave inspections of

the blade taper bores for cracks after the lead wool has

been removed. The Rev. 1 ASB's permit the installation of a plastic

cone in the taper bore that will enhance resistance to corrosion and

mechanical damage. Inspection procedures are the same.

In addition the FAA has approved ASB's No. 14RF-9-61-A95, No. 14RF-

19-61-A57, No. 14RF-21-61-A75, No. 14SF-61-A95, and No. 6/5500/F-61-

A43, all dated December 18, 1995, and No. 14RF-9-61-A95, Rev 1, No.

14RF-19-61-A57, Rev 1, No. 14RF-21-61-A75, Rev 1, No. 14SF-61-A95, Rev

1, and No. 6/5500/F-61-A43, Rev 1, all dated December 21, 1995, that

describe ultrasonic shear wave inspection that can be accomplished

without removing the lead from the taper bore which permits an on-wing

inspection of the blade taper bores for cracks. The Rev. 1 ASB's do not

require immediate removal of the blades that cannot be inspected for

cracks due to the lead wool absorbing the ultrasonic signal. These

blades may be removed at any time within the applicable compliance

period. Inspection procedures are the same.

Since an unsafe condition has been identified that is likely to

exist or develop on other propellers of this same type design, this AD

supersedes priority letter AD 95-18-06R1 to require all Hamilton

Standard Model 14RF-9, -19, -21; and 14SF-5, -7, -11, -15, -17, -19,

and -23; and Hamilton Standard/British Aerospace 6/5500/F propeller

blades be calibrated for ultrasonic transmissibility before conducting

an ultrasonic shear wave inspection. The actions and inspection

intervals for each propeller model are required to be accomplished in

accordance with the service bulletins described previously.

Since a situation exists that requires the immediate adoption of

this regulation, it is found that notice and opportunity for prior

public comment hereon are impracticable, and that good cause exists for

making this amendment effective in less than 30 days.

Comments Invited

Although this action is in the form of a final rule that involves

requirements affecting flight safety and, thus, was not preceded by

notice and an opportunity for public comment, comments are invited on

this rule. Interested persons are invited to comment on this rule by

submitting such written data, views, or arguments as they may desire.

Communications should identify the Rules Docket number and be submitted

in triplicate to the address specified under the caption ADDRESSES. All

communications received on or before the closing date for comments will

be considered, and this rule may be amended in light of the comments

received. Factual information that supports the commenter's ideas and

suggestions is extremely helpful in evaluating the effectiveness of the

AD action and determining whether additional rulemaking action would be

needed.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the rule that might

suggest a need to modify the rule. All comments submitted will be

available, both before and after the closing date for comments, in the

Rules Docket for examination by interested persons. A report that

summarizes each FAA-public contact concerned with the substance of this

AD will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this notice must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket Number 95-ANE-73.'' The postcard will be date stamped and

returned to the commenter.

The regulations adopted herein will not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this final

rule does not have sufficient federalism implications to warrant the

preparation of a Federalism Assessment.

The FAA has determined that this regulation is an emergency

regulation that must be issued immediately to correct an unsafe

condition in aircraft, and is not a ``significant regulatory action''

under Executive Order 12866. It has been determined further that this

action involves an emergency regulation under DOT Regulatory Policies

and Procedures (44 FR 11034, February 26, 1979). If it is determined

that this emergency regulation otherwise would be significant under DOT

Regulatory Policies and Procedures, a final regulatory evaluation will

be prepared and placed in the Rules Docket. A copy of it, if filed, may

be obtained from the Rules Docket at the location provided under the

caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 USC 106(g), 40101, 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

96-01-01 Hamilton Standard: Amendment 39-9477. Docket No. 95-ANE-73.

Supersedes AD 95-18-06R1.

Applicability: Hamilton Standard Models 14RF-9, -14RF-19, 14RF-

21; and 14SF-5, 14SF-7, 14SF-11, 14SFL11, 14SF-15, 14SF-17, 14SF-19,

and 14SF-23; and Hamilton Standard/British Aerospace 6/5500/F

propellers installed on but not limited to Embraer EMB-120, EMB-

120RT; Aerospatiale ATR42-100, ATR42-300, ATR42-320, ATR72, ATR72-

210; deHavilland DHC-8-100 series, DHC-8-200 series, DHC-8-300

series; SAAB-SCANIA SF 340B; Canadair CL-215T, CL-415;

Construcciones Aeronauticas SA (CASA) CN-235 series; and British

Aerospace ATP aircraft.

Note: This airworthiness directive (AD) applies to each

propeller identified in the preceding applicability provision,

regardless of whether it has been modified, altered, or repaired in

the area subject to the requirements of this AD. For propellers that

have been modified, altered, or repaired so that the performance of

the requirements of this AD is affected, the owner/operator must use

the authority provided in paragraph (n) to request approval from the

Federal Aviation Administration (FAA). This approval may address

either no action, if the current configuration eliminates the unsafe

condition, or different actions necessary to address the unsafe

condition described in this AD. Such a request should include an

assessment of the effect of the changed configuration on the unsafe

condition addressed by this AD. In no case does the presence of any

modification, alteration, or repair remove any propeller from the

applicability of this AD.

Compliance: Required as indicated, unless accomplished

previously.

To prevent separation of a propeller blade due to cracks

initiating in the blade taper bore, that can result in aircraft

damage, and possible loss of aircraft control, accomplish the

following:

(a) For Hamilton Standard Model 14RF-9 propeller blades, with

Serial Numbers less than 882038 and listed in Hamilton Standard

Alert Service Bulletins (ASB's) No. 14RF-9-61-A95, dated December

18, 1995, or No. 14RF-9-61-A95, Rev 1, dated December 21, 1995,

installed on but not limited to Embraer EMB-120 and EMB-120RT series

aircraft, accomplish the following:

(1) Within the next 150 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14RF-9-61-A95, dated

December 18, 1995, or No. 14RF-9-61-A95, Rev 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standard ASB's No. 14RF-9-61-A91, dated

December 7, 1995, or No. 14RF-9-61-A91, Rev 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-

9-61-A95, dated December 18, 1995, or No. 14RF-9-61-A95, Rev 1,

dated December 21, 1995, within 500 flight cycles since last

inspection or 150 flight cycles after the effective date of this AD,

whichever occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14RF-9-61-A95, dated

December 18, 1995, or No. 14RF-9-61-A95, Rev 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal, must be

inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 14RF-9-61-A91, dated December 7, 1995,

or No. 14RF-9-61-A91, Rev 1 dated December 15, 1995, within the next

150 flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-9-61-A95, dated December 18, 1995, or No. 14RF-9-61-A95, Rev 1,

dated December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-9-

61-A91 dated December 7, 1995, or No. 14RF-9-61-A91, Rev 1 dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-9-61-A91, dated December 7, 1995, or No. 14RF-9-61-A91, Rev 1,

dated December 15, 1995, must be removed from service, and replaced

with a serviceable part prior to further flight.

(b) For Hamilton Standard Models 14SF-5, -7, -11, -15, and -23

propeller blades with Serial Numbers less than 882038 and listed in

Hamilton Standard ASB's No. 14SF-61-A95, dated December 18, 1995, or

No. 14SF-61-A95, Rev 1, dated December 21, 1995, installed on but

not limited to Aerospatiale ATR42-100, ATR42-300, ATR42-320, ATR72

and deHavilland DHC-8-100, DHC-8-200, DHC-8-300 series aircraft,

accomplish the following:

(1) Within the next 150 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95, Rev 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standard ASB's No. 14SF-61-A93, dated

December 7, 1995, or No. 14SF-61-A93, Rev 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishments Instructions of Hamilton Standard ASB's No.

14SF-61-A95, dated December 18, 1995, or No. 14SF-61-A95, Rev 1,

dated December 21, 1995, within 500 flight cycles since last

inspection or 150 flight cycles after the effective date of this AD,

whichever occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95, Rev 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal, must be

inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 14SF-61-A93, dated December 7, 1995, or

No. 14SF-61-A93, Rev 1, dated December 15, 1995, within the next 150

flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A95, dated December 18, 1995, or No. 14SF-61-A95, dated

December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14SF-61-

A93, dated December 7, 1995, or No. 14SF-61-A93, Rev 1, dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A93, dated December 7, 1995, or No. 14SF-61-A93, Rev 1,

dated December 15, 1995, must be removed from service and replaced

with a serviceable part prior to further flight.

(c) For Hamilton Standard Model 14RF-9 propeller blades with

Serial Numbers less than 882038 and not listed in Hamilton Standard

ASB's No. 14RF-9-61-A95, dated December 18, 1995, or No. 14RF-9-61-

A95, Rev 1, dated December 21, 1995, installed on but not limited to

Embraer EMB 120 and EMB 120RT series aircraft, accomplish the

following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14RF-9-61-A95, dated

December 18, 1995, or No. 14RF-61-A95, Rev 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standards ASB's No. 14RF-9-61-A91, dated

December 7, 1995, or No. 14RF-9-61-A91, Rev 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-

9-61-A95, dated December 18, 1995, or No. 14RF-9-61-A95, Rev 1,

dated December 21, 1995, within 300 flight cycles since last

inspection or 150 flight cycles after the effective date of this AD,

whichever occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14RF-9-61-A95, dated

December 18, 1995, or No. 14RF-9-61-A95, Rev. 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal, must be

inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 14RF-9-61-A91, dated December 7, 1995,

or No. 14RF-9-61-A91, Rev. 1, dated December 15, 1995, within the

next 300 flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-9-61-A95, dated December 18, 1995, or No. 14RF-9-61-A95, dated

December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-9-

61-A91, dated December 7, 1995, or No. 14RF-9-61-A91 Rev. 1, dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-9-61-A91, dated December 7, 1995, or No. 14RF-9-61-A91, Rev. 1,

dated December 15, 1995, must be removed from service and replaced

with a serviceable part prior to further flight.

(d) For Hamilton Standard Models 14SF-5, -7, -11, -15, -17, -19,

and -23 propeller blades with Serial Numbers less than 882038 and

not listed in ASB's No. 14SF-61-A95, dated December 18, 1995, or No.

14SF-61-A95, Rev. 1, dated December 21, 1995, installed on but not

limited to Aerospatiale ATR42-100, ATR42-300, ATR42-320, ATR72,

ATR72-210 and deHavilland DHC-8-100, DHC-8-200, DHC-8-300 series

aircraft, accomplish the following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95 Rev. 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standards ASB's No. 14SF-61-A93, dated

December 7, 1995, or No. 14SF-61-A93, Rev. 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14SF-

61-A95, dated December 18, 1995, or No. 14SF-61-A95, Rev. 1, dated

December 21, 1995, within 500 flight cycles since last inspection or

300 flight cycles after the effective date of this AD, whichever

occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-

A95, Rev. 1, dated December 21, 1995, due to the lead wool absorbing

the ultrasonic signal, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14SF-61-

A93, dated December 7, 1995, or No. 14SF-61-A93, Rev. 1, dated

December 15, 1995, within the next 300 flight cycles after the

effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A95, dated December 18, 1995, or No. 14SF-61-A95, Rev. 1,

dated December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14SF-61-

A93, dated December 7, 1995, or No. 14SF-61-A93, Rev. 1, dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A93, dated December 7, 1995, or No. 14SF-61-A93, Rev. 1,

dated December 15, 1995, must be removed from service and replaced

with a serviceable part prior to further flight.

(e) For all Hamilton Standard Models 14SF-17, and -19 propeller

blades with Serial Numbers less than 882038, installed on but not

limited to Canadair CL-215T and CL-415 series aircraft, accomplish

the following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95, Rev. 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standards ASB's No. 14SF-61-A93, dated

December 7, 1995, or No. 14SF-61-A93, Rev. 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14SF-

61-A95, dated December 18, 1995, or No. 14SF-61-A95, Rev. 1, dated

December 21, 1995, within 500 flight cycles since last inspection or

300 flight cycles after the effective date of this AD, whichever

occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95, Rev. 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal, must be

inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 14SF-61-A93 dated December 7, 1995, or

No. 14SF-61-A93, Rev. 1, dated December 15, 1995, within the next

300 flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A95, dated December 18, 1995, or No. 14SF-61-A95 Rev. 1,

dated December 21, 1995, must be removed from service and inspected

in accordance with the Accomplishment Instructions of Hamilton

Standard ASB's No. 14SF-61-A93, dated December 7, 1995, or No. 14SF-

61-A93 Rev. 1, dated December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14SF-61-A93, dated December 7, 1995, or No. 14SF-61-93, Rev. 1,

dated December 15, 1995, must be removed from service and replaced

with a serviceable part prior to further flight.

(f) For all Hamilton Standard Models 14RF-19 propeller blades

with Serial Numbers less than 882038, installed on but not limited

to SAAB-SCANIA SF 340B series aircraft, accomplish the following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14RF-19-61-A57, dated

December 18, 1995, or No. 14RF-19-61-A57, Rev. 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standards ASB's No. 14RF-19-61-A55, dated

December 7, 1995, or No. 14RF-19-61-A55, Rev. 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-

19-61-A57, dated December 18, 1995, or No. 14RF-19-61-A57 Rev. 1,

dated December 21, 1995, within 1,000 flight cycles since last

inspection or 300 flight cycles after the effective date of this AD,

whichever occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14SF-61-A95, dated

December 18, 1995, or No. 14SF-61-A95 Rev. 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal inspect

in accordance with the Accomplishment Instructions of Hamilton

Standard ASB's No. 14SF-61-A93, dated December 7, 1995, or No. 14SF-

61-A93, Rev. 1, dated December 15, 1995, within the next 300 flight

cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's 14RF-19-

61-A57, dated December 18, 1995, or No. 14RF-19-61-A57, Rev. 1,

dated December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-19-

61-A55, dated December 7, 1995, or No. 14RF-19-61-A55, Rev. 1, dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 1,000 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-19-61-A55, dated December 7, 1995, or No. 14RF-19-61-A55, Rev.

1, dated December 15, 1995, must be removed from service and

replaced with a serviceable part prior to further flight.

(g) For all Hamilton Standard Model 14RF-21 propeller blades

with Serial Numbers less than 882038, installed on but not limited

to Construcciones Aeronautic SA (CASA) CN-235 series aircraft,

accomplish the following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 14RF-21-61-A75, dated

December 18, 1995, or No. 14RF-61-A75, Rev. 1, dated December 21,

1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standard ASB's No. 14RF-19-61-A55, dated

December 7, 1995, or No. 14RF-19-61-A55, Rev. 1, dated December 15,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-

19-61-A57, dated December 18, 1995, or No. 14RF-19-61-A57, Rev. 1,

dated December 21, 1995, within 1,000 flight cycles since last

inspection or 300 flight cycles after the effective date of this AD,

whichever occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 14RF-21-61-A75, dated

December 18, 1995, or No. 14RF-61-A75, Rev. 1, dated December 21,

1995, due to the lead wool absorbing the ultrasonic signal, must be

inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 14RF-21-61-A73, dated December 7, 1995,

or No. 14RF-21-61-A73, Rev. 1, dated December 15, 1995, within the

next 300 flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-21-61-A75, dated December 18, 1995, or No. 14RF-21-61-A75, Rev.

1, dated December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 14RF-21-

61-A73, dated December 7, 1995, or No. 14RF-21-61-A73, Rev. 1, dated

December 15, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 2,500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No.

14RF-21-61-A73, dated December 7, 1995, or No. 14RF-21-61-A73, Rev.

1, dated December 15, 1995, must be removed from service and

replaced with a serviceable part prior to further flight.

(h) For all Hamilton Standard/British Aerospace 6/5500/F

propeller blades, with Serial Numbers less than 882038, installed on

but not limited to British Aerospace ATP series aircraft, accomplish

the following:

(1) Within the next 300 flight cycles, after the effective date

of this AD, perform an ultrasonic shear wave inspection for cracks

in the blade taper bore in accordance with the Accomplishment

Instructions of Hamilton Standard ASB's No. 6/5500/F-61-A43, dated

December 18, 1995, or No. 6/5500/F-61-A43, Rev. 1, dated December

21, 1995.

(2) For propeller blades that have been previously inspected in

accordance with Hamilton Standard ASB's No. 6/5500/F-61-A41, dated

December 7, 1995, or No. 6/5500/F-61-A41, Rev. 1, dated December 18,

1995, perform an ultrasonic shear wave inspection in accordance with

the Accomplishment Instructions of Hamilton Standard ASB's No. 6/

5500/F-61-A43, or No. 6/5500/F-61-A43, Rev. 1, dated December 21,

1995, as applicable within 2,500 flight cycles since last inspection

or 300 flight cycles after the effective date of this AD, whichever

occurs later.

(3) Propeller blades that cannot be inspected for cracks in

accordance with Hamilton Standard ASB's No. 6/5500/F-61-A43, dated

December 18, 1995, or No. 6/5500/F-61-A43, Rev. 1, dated December

21, 1995, due to the lead wool absorbing the ultrasonic signal, must

be inspected in accordance with the Accomplishment Instructions of

Hamilton Standard ASB's No. 6/5500/F-61-A41, dated December 7, 1995,

or No. 6/5500/F-61-A41, Rev. 1, dated December 18, 1995, within the

next 300 flight cycles after the effective date of this AD.

(4) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No. 6/

5500/F-61-A43, dated December 18, 1995, or No. 6/5500/F-61-A43, Rev.

1, dated December 21, 1995, must be inspected in accordance with the

Accomplishment Instructions of Hamilton Standard ASB's No. 6/5500/F-

61-A41, dated December 7, 1995, or No. 6/5500/F-61-A41, Rev. 1,

dated December 18, 1995.

(5) Thereafter, perform repetitive ultrasonic shear wave

inspections at intervals not to exceed 2,500 flight cycles in

accordance with the applicable SB's.

(6) Propeller blades that have ultrasonic shear wave indications

that exceed the limits specified in Hamilton Standard ASB's No. 6/

5500/F-61-A41, dated December 7, 1995, or No. 6/5500/F-61-A41, Rev.

1, dated December 18, 1995, must be removed from service and

replaced with a serviceable part prior to further flight.

(i) For all currently installed Hamilton Standard Model 14SFL11

propellers installed on Aerospatiale ATR72-210 series aircraft

remove all 14SFL11 propellers from service within the next 150

flight cycles, after the effective date of this AD, and replace with

serviceable Hamilton Standard 247F propellers.

(j) The ultrasonic inspection of the propeller blade taper bore

must be performed by a Level II inspector who is qualified under the

guidelines established by the American Society of Nondestructive

Testing or MIL-STD-410 or FAA approved equivalent, and must be

trained by Hamilton Standard approved personnel on how to do this

inspection procedure. The individual returning the aircraft to

service is required to verify that the ultrasonic inspection was

accomplished in accordance with the requirements of this paragraph.

(k) For repetitive inspections, propeller blades may be

evaluated to determine if the lead wool is absorbing the ultrasonic

signal at any time during the 500 flight cycle repetitive inspection

interval to determine if the lead wool removal is required to

complete the ultrasonic shear wave inspection.

(l) For the purpose of this AD, a flight cycle is defined as one

takeoff and the next landing of an aircraft. In addition, each touch

and go is defined as a flight cycle, and each water load pickup for

amphibian aircraft operation is defined as a flight cycle.

(m) Propeller blades removed from service after inspections

performed in accordance with AD 95-18-06R1, and subsequently

inspected in accordance with the requirements of this AD and found

to be serviceable, may be returned to service.

(n) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Boston Aircraft Certification

Office. The request should be forwarded through an appropriate FAA

Principal Maintenance Inspector, who may add comments and then send

it to the Manager, Boston Aircraft Certification Office.

Note: Information concerning the existence of approved

alternative methods of compliance with this airworthiness directive,

if any, may be obtained from the Boston Aircraft Certification

Office.

(o) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the aircraft to a location where

the requirements of this AD can be accomplished.

(p) The ultrasonic shear wave inspections and removal and

replacement of propeller blades shall be done in accordance with the

following Hamilton Standard Alert Service Bulletins:

------------------------------------------------------------------------

Document No. Revision Date

------------------------------------------------------------------------

No. 14RF-9-61-A91; Total Pages:40. ........ Dec. 7, 1995.

No. 14RF-9-61-A91; Total Pages: 42 1 Dec. 15, 1995.

No. 14RF-19-61-A55; Total Pages: ........ Dec. 7, 1995.

40.

No. 14RF-19-61-A55; Total Pages: 1 Dec. 15, 1995.

42.

No. 14RF-21-61-A73; Total Pages: ........ Dec. 7, 1995.

40.

No. 14RF-21-61-A73; Total Pages: 1 Dec. 15, 1995.

42.

No. 14SF-61-A93; Total Pages: 40.. ........ Dec. 7, 1995.

No. 14SF-61-A93, Total Pages: 42.. 1 Dec. 15, 1995.

No. 6/5500/F-61-A41; Total Pages: ........ Dec. 7, 1995.

40.

No. 6/5500/F-61-A41; Total Pages: 1 Dec. 18, 1995.

42.

No. 14RF-9-61-A95; Total Pages: 36 ........ Dec. 18, 1995.

No. 14RF-9-61-A95; Total Pages: 36 1 Dec. 21, 1995.

No. 14RF-19-61-A57; Total Pages: ........ Dec. 18, 1995.

35.

No. 14RF-19-61-A57; Total Pages: 1 Dec. 21,1995.

35.

No. 14RF-21-61-A75, Total Pages: ........ Dec. 18, 1995.

35.

No. 14RF-21-61-A75; Total Pages: 1 Dec. 21,1995.

35.

No. 14SF-61-A95; Total Pages: 37.. ........ Dec. 18, 1995.

No. 14SF-61-A95; Total Pages: 37.. 1 Dec. 21, 1995.

No. 6/5500/F-61-A43; Total Pages: ........ Dec. 18, 1995.

35.

No. 6/5500/F-61-A43; Total Pages: 1 Dec. 21, 1995.

35.

------------------------------------------------------------------------

This incorporation by reference was approved by the Director of

the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR

part 51. Copies may be obtained from Hamilton Standard, One Hamilton

Road, Windsor Locks, CT 06096-1010; telephone (203) 654-6876. This

information may be inspected at the FAA, New England Region, Office

of the Assistant Chief Counsel, 12 New England Executive Park,

Burlington, MA; or at the Office of the Federal Register, 800 North

Capitol Street, NW., suite 700, Washington, DC.

(q) This amendment supersedes priority letter AD 95-18-06R1,

issued August 30, 1995.

(r) This amendment becomes effective on January 19, 1996.

Issued in Burlington, Massachusetts, on December 26, 1995.

Jay J. Pardee,

Manager, Engine and Propeller Directorate, Aircraft Certification

Service.

[FR Doc. 96-268 Filed 1-8-96; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.