Airworthiness Directives; CFE Company Model CFE738-1-1B Turbofan Engines

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 65 › 65 FR 691

This text was captured on Sep 30, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

Rules and Regulations

Federal Register

________________________________________________________________________

The Code of Federal Regulations is sold by the Superintendent of Documents.

Prices of new books are listed in the first FEDERAL REGISTER issue of each

week.

========================================================================

and Regulations

=======================================================================

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 99-NE-39-AD; Amendment 39-11497; AD 99-27-16]

RIN 2120-AA64

Airworthiness Directives; CFE Company Model CFE738-1-1B Turbofan

Engines

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),

applicable to CFE Company Model CFE738-1-1B turbofan engines. This AD

requires, on certain engines identified by serial numbers: a one-time

visual inspection of Stage 2 high pressure turbine (HPT) aft cooling

plates for nicks, dents, and scratches, and if present, dimensional

inspection of indentation depth; repair, if indentation is within

acceptable limits, and, if necessary, replacement with serviceable

parts. This AD also requires inspection for raised metal on the Stage 2

HPT rotor disk post aft surface that mates with the Stage 2 HPT aft

cooling plate, and removal of the raised metal, if present. This

amendment is prompted by reports of Stage 2 HPT aft cooling plates that

were dented during the assembly of the cooling plate to the Stage 2

disk due to raised metal on the stage 2 HPT disk post aft mating

surface. The actions specified by this AD are intended to prevent aft

HPT cooling plate failure, which could result in an uncontained engine

failure and damage to the airplane.

DATES: Effective February 10, 2000.

The incorporation by reference of certain publications listed in

the regulations is approved by the Director of the Federal Register as

of February 10, 2000.

ADDRESSES: The service information referenced in this AD may be

obtained from CFE Company, Data Distribution, MS 64-03/2101-201, PO Box

29003 Phoenix, AZ 85038-9003; telephone (602) 365-2493, fax (602) 365-

5577. This information may be examined at the Federal Aviation

Administration (FAA), New England Region, Office of the Regional

Counsel, 12 New England Executive Park, Burlington, MA; or at the

Office of the Federal Register, 800 North Capitol Street, NW, suite

700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Keith Mead, Aerospace Engineer, Engine

Certification Office, FAA, Engine and Propeller Directorate, 12 New

England Executive Park, Burlington, MA 01803-5299; telephone (781) 238-

7744, fax (781) 238-7199.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal

Aviation Regulations (14 CFR part 39) to include an airworthiness

directive (AD) that is applicable to certain CFE Company Model CFE738-

1-1B turbofan engines was published in the Federal Register on

September 28, 1999 (64 FR 52259). That action proposed to require, on

certain engines identified by serial numbers: a one-time visual

inspection of Stage 2 high pressure turbine (HPT) aft cooling plates

for nicks, dents, and scratches, and if present, dimensional inspection

of indentation depth; repair, if indentation is within acceptable

limits, and, if necessary, replacement with serviceable parts. This Ad

also requires inspection for raised metal on the Stage 2 HPT rotor disk

post aft surface that mates with the Stage 2 HPT aft cooling plate, and

removal of the raised metal, if present. That action was prompted by

reports of Stage 2 HPT aft cooling plates that were dented during the

assembly of the cooling plate to the Stage 2 disk due to raised metal

on the stage 2 HPT disk post aft mating surface. That condition, if not

corrected, could result in aft HPT cooling plate failure, which could

result in an uncontained engine failure and damage to the airplane.

No Comments Received

Interested persons have been afforded an opportunity to participate

in the making of this amendment. No comments were received on the

proposal or the FAA's determination of the cost to the public. The FAA

has determined that air safety and the public interest require the

adoption of the rule as proposed.

Economic Analysis

There are approximately 72 engines of the affected design in the

worldwide fleet. The FAA estimates that 48 engines installed on

aircraft of US registry will be affected by this AD, that it will take

approximately 4 work hours per engine to accomplish the required

inspection if the inspection does not take place during scheduled

maintenance, and that the average labor rate is $60 per work hour.

Required parts cost approximately $1,536 per engine. Based on these

figures, the total cost impact of the AD on US operators is estimated

to be $106,560.

Regulatory Impact

The regulations adopted herein will not have a substantial direct

effect on the States, on the relationship between the national

Government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, it

is determined that this final rule does not have federalism

implications under Executive Order (EO) 13132.

For the reasons discussed above, I certify that this action (1) is

not a ``significant regulatory action'' under EO 12866; (2) is not a

``significant rule'' under DOT Regulatory Policies and Procedures (44

FR 11034, February 26, 1979); and (3) will not have a significant

economic impact, positive or negative, on a substantial number of small

entities under the criteria of the Regulatory Flexibility Act. A final

evaluation has been prepared for this action and it is contained in the

Rules Docket. A copy of it may be obtained from the Rules Docket at the

location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by

reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration amends part 39 of

the

Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

99-27-16 CFE Company: Amendment 39-11497. Docket 99-NE-39-AD.

Applicability: CFE Model CFE738-1-1B turbofan engines, serial

numbers (S/Ns) 105267 through 105339, inclusive. These engines are

installed on but not limited to Dassault-Breguet Falcon 2000 series

aircraft.

Note 1: This airworthiness directive (AD) applies to each engine

identified in the preceding applicability provision, regardless of

whether it has been modified, altered, or repaired in the area

subject to the requirements of this AD. For engines that have been

modified, altered, or repaired so that the performance of the

requirements of this AD is affected, the owner/operator must request

approval for an alternative method of compliance in accordance with

paragraph (b) of this AD. The request should include an assessment

of the effect of the modification, alteration, or repair on the

unsafe condition addressed by this AD; and, if the unsafe condition

has not been eliminated, the request should include specific

proposed actions to address it.

Compliance: Required as indicated, unless accomplished

previously.

To prevent aft HPT cooling plate failure, which could result in

an uncontained engine failure and damage to the airplane, accomplish

the following:

Inspections and Follow-On Actions

(a) At the next engine shop visit after the effective date of

this AD where the HPT assembly is sufficiently disassembled to

afford access to the Stage 2 HPT aft cooling plate, but not later

than 4500 part cycles-since-new (CSN), accomplish the following in

accordance with CFE Alert Service Bulletin (ASB) No. CFE738-A72-

8031, Revision 1, dated June 23, 1999, as follows:

(1) Inspect the stage 2 HPT aft cooling plate for nicks, dents,

and scratches on surface D in accordance with the requirements of

ASB No. CFE738-A72-8031, paragraph 2.B.(1).

(2) Repair those stage 2 HPT aft cooling plates with indentation

less than 0.003 inch deep in accordance with ASB No. CFE738-A72-

8031. paragraph 2.B.(1).

(3) Remove from service prior to further flight those stage 2

HPT aft cooling plates that have nicks, dents, and/or scratches that

exceed the acceptance limits in accordance with ASB No. CFE738-A72-

8031 paragraph 2.B.(1), and replace with serviceable parts.

(4) Inspect the stage 2 HPT rotor disk post aft mating surface

for raised metal, and remove raised metal if present in accordance

with ASB No. CFE738-A72-8031, paragraph 2.B.(2).

Alternative Methods of Compliance

(b) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Engine Certification Office (ECO).

Operators shall submit their request through an appropriate FAA

Principal Maintenance Inspector, who may add comments and then send

it to the Manager, ECO.

Note 2: Information concerning the existence of approved

alternative methods of compliance with this airworthiness directive,

if any, may be obtained from the ECO.

Ferry Flights

(c) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the inspection requirements of this AD can be accomplished.

Incorporation by Reference

(d) The actions required by this AD shall be done in accordance

with the following CFE ASB:

------------------------------------------------------------------------

Document No. Revision Pages Date

------------------------------------------------------------------------

CFE738-A72-8031.............. 1............ 1 June 23, 1999.

Original..... 2-5 May 17, 1999.

Total pages: 5.

------------------------------------------------------------------------

This incorporation by reference was approved by the Director of

the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR

part 51. Copies may be obtained from CFE Company, Data Distribution,

MS 64-03/2101-201, P.O. , PO Box 29003 Phoenix, AZ 85038-9003;

telephone (602) 365-2493, fax (602) 365-5577. Copies may be

inspected at the FAA, New England Region, Office of the Regional

Counsel, 12 New England Executive Park, Burlington, MA; or at the

Office of the Federal Register, 800 North Capitol Street, NW, suite

700, Washington, DC.

(e) This amendment becomes effective on February 10, 2000.

Issued in Burlington, Massachusetts, on December 29, 1999.

Jay J. Pardee,

Manager, Engine and Propeller Directorate, Aircraft Certification

Service.

[FR Doc. 00-133 Filed 1-5-00; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.

Airworthiness Directives; CFE Company Model CFE738-1-1B Turbofan Engines · 65 FR 691 | Frix