Section 223.120 Incorporations by Reference

Section 223.120  Incorporations by Reference

The following materials are incorporated by reference. These

incorporations do not include any later amendments or editions.

a)         40

CFR 59, subpart D, appendix A, Determination of Volatile Matter Content of

Methacrylate Multicomponent Coatings Used as Traffic Marking Coatings, 64 Fed.

Reg. 35002 (June 30, 1999).

b)         40

CFR 59, subpart C, National Volatile Organic Compound Emission Standards for

Consumer Products, 69 Fed. Reg. 18803 (April 4, 2004).

c)         40

CFR 60, appendix A, Method 24, Determination of Volatile Matter Content, Water

Content, Density, Volume Solids, and Weight Solids of Surface Coatings, 36 Fed.

Reg. 24877  (December 23, 1971).

d)         40

CFR 82, subpart A, appendix A, Class I Controlled Substances, 68 Fed. Reg.

42892 (July 18, 2003) and appendix B, Class II Controlled Substances, 68 Fed.

Reg. 2859 (January 21, 2003).

e)         29

CFR 1910.1200(d)(4), Hazard Communication, 61 Fed. Reg. 9245 (March 7, 1996).

f)         ASTM

International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken PA

19428-2959.

1)         ASTM

E119-05a, Standard Test Methods for Fire Tests of Building Construction and

Materials, approved November 1, 2005.

2)         ASTM

D523-89 (1999), Standard Test Method for Specular Gloss, approved May 10, 1999.

3)         ASTM

D1640-03, Standard Test Methods for Drying, Curing, or Film Formation of

Organic Coatings at Room Temperature, approved December 1, 2003.

4)         ASTM

D3912-95 (2001), Test Method for Chemical Resistance of Coating Used in

Light-Water Nuclear Power Plants, reapproved 2001.

5)         ASTM

D4082-02, Test Method for Effects of Radiation on Coatings Used in Light-Water

Nuclear Power Plants, approved 2002.

6)         ASTM

D4214-98, Standard Test Methods for Evaluating the Degree of Chalking of Exterior

Paint Films, approved August 10, 1998

STM

D3912-95 (2001), Test Method for Chemical Resistance of Coating Used in

Light-Water Nuclear Power Plants, reapproved 2001.

5)         ASTM

D4082-02, Test Method for Effects of Radiation on Coatings Used in Light-Water

Nuclear Power Plants, approved 2002.

6)         ASTM

D4214-98, Standard Test Methods for Evaluating the Degree of Chalking of Exterior

Paint Films, approved August 10, 1998.

7)         ASTM

D1613-03, Standard Test Method for Acidity in Volatile Solvents and Chemical

Intermediates Used in Paint, Varnish, Lacquer, and Related Products, approved

October 1, 2003.

8)         ASTM

E84-07, Standard Test Method for Surface Burning Characteristics of Building

Materials, approved 2007.

9)         ASTM

D4359-90 (2006), Standard Test Method for Determining Whether a Material is a

Liquid or a Solid, reapproved 2006.

10)         ASTM

E260-96 (2006), Standard Practice for Packed Column Gas Chromatography,

reapproved 2006.

11)         ASTM

E2167-01, Standard Guide for Selection and Use of Stone Consolidants (see

section 4, Stone Consolidant), approved 2001.

12)         ASTM

C836-06, Specification for High Solids Content, Cold Liquid-Applied Elastomeric

Waterproofing Membrane for Use with Separate Wearing Course, approved 2006.

13)         ASTM

D86-07b, Standard Test Method for Distillation of Petroleum Products at

Atmospheric Pressure, approved 2007.

g)       South

Coast Air Quality Management District, 21865 Copley Dr., Diamond Bar CA

91765.

1)         South

Coast Air Quality Management District (SCAQMD) Method 304-91, Determination of

Volatile Organic Compounds in Various Materials, revised February 1996.

2)         SCAQMD

Method 303-91, Determination of Exempt Compounds, revised February 1993.

3)         SCAQMD

Method 318-95, Determination of Weight Percent Elemental Metal in Coatings by

X-Ray Diffraction, approved July 1996.

4)         SCAQMD

Rule 1174, Ignition Method Compliance Certification Protocol (adopted October

5, 1990)

e Organic Compounds in Various Materials, revised February 1996.

2)         SCAQMD

Method 303-91, Determination of Exempt Compounds, revised February 1993.

3)         SCAQMD

Method 318-95, Determination of Weight Percent Elemental Metal in Coatings by

X-Ray Diffraction, approved July 1996.

4)         SCAQMD

Rule 1174, Ignition Method Compliance Certification Protocol (adopted October

5, 1990).

h)         Bay

Area Air Quality Management District Office, 939 Ellis Street, San Francisco CA

94109.

1)         Bay

Area Air Quality Management District (BAAQMD) Method 43, Determination of

Volatile Methylsiloxanes in Solvent-Based Coatings, Inks, and Related

Materials, proposed amendment February 4, 2004.

2)         BAAQMD

Method 41, Determination of Volatile Organic Compounds in Solvent-Based

Coatings and Related Materials Containing Parachlorobenzotrifluoride, proposed

amendment February 4, 2004.

i)          California

Air Resources Board (CARB) Method 310, Determination of Volatile Organic

Compounds in Consumer Products and Reactive Organic Compounds in Aerosol

Coating Products, amended May 5, 2005.  California Air Resources Board, 1001 I

Street, PO Box 2815, Sacramento CA 95812.

j)          California

Code of Regulations (CCR), title 17 § 94509(h), Standards for Consumer Products

(2005).

k)         California Code, Health

and Safety Code, § 41712(h)(2) (2005).

l)          17 CCR

Article 4, Alternate Control Plan §§ 94540-94555 (1996).

m)        17 CCR § 94511,

Innovative Products (1997).

n)         17 CCR § 94503.5,

Innovative Products (1996).

o)         7 USC

136 to 136y, FIFRA, Environmental Pesticide Control, published January 19,

2004, in Supplement III of the 2000 Edition of the United States Code.

p)         Federal

Specification MMM-A-181D, Adhesives, Phenol, Resorcinol, or Melamine Base

(1980).