Updates to Marine Engineering Standards

FederalRegulations

Ask Donna

How this section applies to your facts.

Federal Register › Vol. 86 › 86 FR 57896

This text was captured on Aug 14, 2026. It is a snapshot, not a live feed, so check the official code before relying on it.

Text

DEPARTMENT OF HOMELAND SECURITY Coast Guard 46 CFR Parts 50, 52, 53, 54, 56, 57, 58, 59, 61, 62, 63, and 64 [Docket No. USCG-2020-0634] RIN 1625-AC72 Updates to Marine Engineering Standards AGENCY:

Coast Guard, DHS.

ACTION:

Notice of proposed rulemaking.

SUMMARY:

The Coast Guard proposes to incorporate by reference updated marine engineering standards and eliminate outdated or unnecessarily prescriptive regulations in Title 46 of the Code of Federal Regulations (CFR) subchapter F. This proposed rule is part of a continuing effort for regulatory reform that increases compliance options for the regulated public while providing a cost savings to the regulated public and the U.S. government.

DATES:

Comments and related material must be received by the Coast Guard on or before December 20, 2021.

ADDRESSES:

You may submit comments identified by docket number USCG-2020-0634 using the Federal eRulemaking Portal at https://www.regulations.gov. See the “Public Participation and Request for Comments” portion of the SUPPLEMENTARY INFORMATION section for further instructions on submitting comments.

FOR FURTHER INFORMATION CONTACT:

For further information about this document call or email Thane Gilman, Systems Engineering Division (CG-ENG-3), 2703 Martin Luther King Jr. Ave. SE, Washington, DC 20593. Phone (202) 372-1383, Email: thane.gilman@uscg.mil.

SUPPLEMENTARY INFORMATION:

Table of Contents for Preamble

I. Public Participation and Request for Comments II. Abbreviations III. Background, Basis, and Purpose IV. Discussion of Proposed Rule A. General Discussion B. Standards Incorporated by Reference C. Standards Previously Approved for Incorporation by Reference D. Section by Section Analysis of Proposed Changes to the Regulatory Text V. Incorporation by Reference VI. Regulatory Analyses A. Regulatory Planning and Review B. Small Entities C. Assistance for Small Entities D. Collection of Information E. Federalism F. Unfunded Mandates Reform Act G. Taking of Private Property H

ted by Reference C. Standards Previously Approved for Incorporation by Reference D. Section by Section Analysis of Proposed Changes to the Regulatory Text V. Incorporation by Reference VI. Regulatory Analyses A. Regulatory Planning and Review B. Small Entities C. Assistance for Small Entities D. Collection of Information E. Federalism F. Unfunded Mandates Reform Act G. Taking of Private Property H. Civil Justice Reform I. Protection of Children J. Indian Tribal Governments K. Energy Effects L. Technical Standards M. Environment I. Public Participation and Request for Comments

The Coast Guard views public participation as essential to effective rulemaking, and will consider all comments and material received during the comment period. Your comment can help shape the outcome of this rulemaking. If you submit a comment, please include the docket number for this rulemaking, indicate the specific section of this document to which each comment applies, and provide a reason for each suggestion or recommendation.

We encourage you to submit comments through the Federal eRulemaking Portal at www.regulations.gov. If you cannot submit your material by using www.regulations.gov, call or email the person in the FOR FURTHER INFORMATION CONTACT section of this proposed rule for alternate instructions. Documents mentioned in this proposed rule, and all public comments, will be available in our online docket at www.regulations.gov, and can be viewed by following that website's instructions. Additionally, if you visit the online docket and sign up for email alerts, you will be notified when comments are posted or if a final rule is published.

We accept anonymous comments. All comments received will be posted without change to https://www.regulations.gov and will include any personal information you have provided. For more about privacy and submissions in response to this document, see the Department of Homeland Security's (DHS) eRulemaking System of Records notice (85 FR 14226, March 11, 2020)

posted or if a final rule is published.

We do not plan to hold a public meeting but we will consider doing so if public comments indicate that a meeting would be helpful. We would issue a separate Federal Register notice to announce the date, time, and location of such a meeting.

II. Abbreviations

ABYC American Boat and Yacht Council ABS American Bureau of Shipping ANSI American National Standards Institute API American Petroleum Institute ASME American Society of Mechanical Engineers ASTM ASTM International BLS Bureau of Labor Statistics BPVC Boiler and Pressure Vessel Code CFR Code of Federal Regulations CG-5PS United States Coast Guard Commercial Regulations and Standards Directorate CGA Compressed Gas Association DHS Department of Homeland Security FR Federal Register GPO Government Publishing Office GS General Service IBR Incorporation by Reference IMO International Maritime Organization ISO International Organization for Standardization MISLE Marine Information for Safety and Law Enforcement MSC Marine Safety Center MSS Manufacturers Standardization Society of the Valve and Fitting Industry, Inc. NAICS North American Industry Classification System NFPA National Fire Protection Association NPRM Notice of Proposed Rulemaking OFR Office of the Federal Register OMB Office of Management and Budget OPM Office of Personnel Management PV Pressure Vessel RA Regulatory Analysis RFA The Regulatory Flexibility Act of 1980 § Section SAE SAE International SBA Small Business Administration SOLAS International Convention for Safety of Life at Sea UL Underwriters Laboratories U.S.C. United States Code III

tice of Proposed Rulemaking OFR Office of the Federal Register OMB Office of Management and Budget OPM Office of Personnel Management PV Pressure Vessel RA Regulatory Analysis RFA The Regulatory Flexibility Act of 1980 § Section SAE SAE International SBA Small Business Administration SOLAS International Convention for Safety of Life at Sea UL Underwriters Laboratories U.S.C. United States Code III. Background, Basis, and Purpose

This notice of proposed rulemaking (NPRM) incorporates by reference updated marine engineering standards in Title 46 of the Code of Federal Regulations (CFR) subchapter F, including standards for boilers, pressure vessels, auxiliary machinery, piping, valves, and fittings, for various types of vessels; adds a limited number of alternative standards; and eliminates outdated or unnecessarily prescriptive regulations.

The Office of Management and Budget (OMB) directs, via OMB Circular A-119, that federal agencies use industry-based voluntary consensus standards in lieu of government-unique requirements where appropriate. The Coast Guard actively participates in the development of industry standards of safety for marine equipment at the International Maritime Organization (IMO), the International Organization for Standardization (ISO), ASTM International (ASTM), American Society of Mechanical Engineers (ASME), and other standards-setting bodies that belong to the American National Standards Institute (ANSI). Recently published editions of these standards provide necessary updates to materials, testing practices, and technologies, enhancing safety and compliance.

ng practices, and technologies, enhancing safety and compliance.

The United States Coast Guard has statutory authority to promulgate regulations under Title 43, United States Code (U.S.C.), section 1333(d); and Title 46 U.S.C. 3306 and 3703, and the Department of Homeland Security Delegation No. 0170.1, which delegates authority under these statutes to the Commandant of the Coast Guard. 43 U.S.C. 1333(d) grants the Secretary the authority to promulgate and enforce regulations with respect to lights and other warning devices, safety equipment, and other matters relating to the promotion of safety of life and property on artificial islands, installations, and other devices. 46 U.S.C. 3306(a)(1) authorizes the Secretary to prescribe regulations for the design, construction, alteration, repair, and operation of vessels subject to inspection, including equipment, appliances, propulsion machinery, auxiliary machinery, boilers, unfired pressure vessels, piping, and electric installations. Additionally, 46 U.S.C. 3703(a) grants the Secretary authority to regulate tank vessels regarding the construction, alteration, repair, maintenance, operation, and equipping of vessels that may be necessary for increased protection against hazards to life and property, for navigation and vessel safety, and for enhanced protection of the marine environment.

IV. Discussion of Proposed Rule

A. General Discussion

In general, the proposed rule would make the following changes:

1. Corrections—we would amend several sections to correct inadvertent errors or deletions. We would also remove material that is obsolete or superfluous to an efficient and effective marine safety regulatory scheme, and update contact information for Coast Guard offices and standards organizations.

2. Stylistic Revisions—we would revise the language of some sections, primarily for greater clarity

. Corrections—we would amend several sections to correct inadvertent errors or deletions. We would also remove material that is obsolete or superfluous to an efficient and effective marine safety regulatory scheme, and update contact information for Coast Guard offices and standards organizations.

2. Stylistic Revisions—we would revise the language of some sections, primarily for greater clarity. This includes revising sentences containing the word “shall” to use “must” or another grammatically equivalent word or phrase in accordance with plain language guidelines, and standardizing terms that were variously presented as compound words, hyphenated constructions, or multi-word phrases using the format preferred by the Government Publishing Office (GPO).

3. Updated cross references—we would update cross references to reflect the relocation, within the CFR, of pertinent provisions. We would also standardize designations for tables, figures, notes, and formulas using the format preferred by the Office of the Federal Register (OFR).

4. Updated industry standards—we would update cross-references to industry standards by adding new references, replacing references to superseded standards or editions, and by conforming text accordingly. We incorporate these updated standards because they reflect the latest available technologies, practices, and procedures that are recommended by consensus bodies, ship classification societies and other maritime organizations with experience in the industry. As the baseline upon which other standards, rules, and equivalency requests are evaluated, it is important that subchapter F incorporate up-to-date references. The class rules of the American Bureau of Shipping (ABS), in particular, are incorporated by reference in multiple locations within subchapter F and 46 CFR Chapter I

ocieties and other maritime organizations with experience in the industry. As the baseline upon which other standards, rules, and equivalency requests are evaluated, it is important that subchapter F incorporate up-to-date references. The class rules of the American Bureau of Shipping (ABS), in particular, are incorporated by reference in multiple locations within subchapter F and 46 CFR Chapter I. It is important to note that while these rules set the regulatory baseline or standard for specific engineering systems and equipment, the Coast Guard has also authorized classification societies in accordance with 46 CFR part 8. These authorized classification societies are listed on the Coast Guard website 1 and have been delegated the authority to perform certain functions and certifications using their respective class rules for vessels enrolled in the Alternate Compliance Program. For vessels not enrolled in the Alternate Compliance Program, the class rules of an authorized classification society may be proposed as an alternative to the ABS class rules incorporated by reference for engineering systems and equipment. The following table indicates the sections we propose to amend, and why.

1 https://www.dco.uscg.mil/Our-Organization/Assistant-Commandant-for-Prevention-Policy-CG-5P/Inspections-Compliance-CG-5PC-/Commercial-Vessel-Compliance/Flag-State-Control-Division/ClassSocAuth/.

BILLING CODE 9110-04-P EP19OC21.007

EP19OC21.008

EP19OC21.009

EP19OC21.010

EP19OC21.011

BILLING CODE 9110-04-C B. Standards Incorporated by Reference To Be Updated or Added

Following this paragraph, we include an alphabetical list of the standards we propose to update or add, each with a listing of the sections in which they appear in Title 46 of the CFR

ntrol-Division/ClassSocAuth/.

BILLING CODE 9110-04-P EP19OC21.007

EP19OC21.008

EP19OC21.009

EP19OC21.010

EP19OC21.011

BILLING CODE 9110-04-C B. Standards Incorporated by Reference To Be Updated or Added

Following this paragraph, we include an alphabetical list of the standards we propose to update or add, each with a listing of the sections in which they appear in Title 46 of the CFR. For each standard listed, we describe the topics covered by the standard, the proposed changes to the standard, any difference between the older edition of standards currently included within the CFR via incorporation by reference (IBR) and the edition proposed for adoption, and a list of subparts or sections that reference the standard.

• American Bureau of Shipping (ABS) standard ABS Rules for Building and Classing Marine Vessels, 2020, Part 4, Vessel Systems and Machinery. This standard updates the 2003 standard, incorporated by reference in §§ 58.01-5, 58.05-1, 58.10-15, 58.20-5, 58.25-5, 62.25-30, 62.35-5, 62.35-35, 62.35-40, 62.35-50, and 62.50-30. In 2020, ABS changed the name of the Steel Vessel Rules to Marine Vessel Rules. All parts and sections contain the same information along with updates to reflect the current technologies for commercial vessels.

• American Boat and Yacht Council (ABYC) standard ABYC P-1-14, Installation of Exhaust Systems for Propulsion and Auxiliary Engines (2009 standard reaffirmed 2014). This standard updates the 1973 standard, incorporated by reference at § 58.10-5. It contains the rules and guidance for the safe installation and operation of exhaust systems for propulsion and auxiliary engines. Updates to the standard are editorial (non-substantive) in nature.

and guidance for the safe installation and operation of exhaust systems for propulsion and auxiliary engines. Updates to the standard are editorial (non-substantive) in nature.

• ANSI Z21.22-2015, Relief valves for hot water supply systems. This standard updates the 1986 edition incorporated by reference at § 63.25-3. This standard establishes requirements for relief valves for hot water systems. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

• API Recommended Practice 14C, Analysis, Design, Installation, and Testing of Safety Systems for Offshore Production Facilities, Eighth Edition, February 2017. This standard updates the 1986 edition, incorporated by reference in § 58.60-9. The updates made to the standard are editorial in nature.

• API STD 53, Well Control Equipment Systems for Drilling Wells, fifth edition. This standard replaces API Recommended Practice 53 (API RP 53), the second edition of which is currently incorporated by reference at § 58.60-7. API STD 53 promotes best safety practices for the oil and gas industry during drilling operations, principally focusing on blowout prevention.

• API STD 607, Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seats, seventh edition (2016). This standard replaces the fourth edition of API STD 607 (1993), incorporated by reference at § 56.20-15. This standard specifies fire type-testing of valves that contain nonmetallic materials and pressure-containing capabilities after the fire test.

• ASME Boiler and Pressure Vessel Code, Section I, Rules for Construction of Power Boilers (2019 edition)

onmetallic Seats, seventh edition (2016). This standard replaces the fourth edition of API STD 607 (1993), incorporated by reference at § 56.20-15. This standard specifies fire type-testing of valves that contain nonmetallic materials and pressure-containing capabilities after the fire test.

• ASME Boiler and Pressure Vessel Code, Section I, Rules for Construction of Power Boilers (2019 edition). The 2001 edition is currently incorporated by reference at §§ 52.01-2, 52.01-5, 52.01-50, 52.01-95, 52.01-100, 52.01-105, 52.01-110, 52.01-115, 52.01-120, 52.01-135, 52.01-140, 52.01-145, 52.05-1, 52.05-15, 52.05-20, 52.05-30, 52.05-45, 52.15-1, 52.15-5, 52.20-1, 52.20-25, 52.25-3, 52.25-5, 52.25-7, 52.25-10, 56.15-1, 56.20-1, 56.60-1, 56.70-15, 56.95-10, 58.30-15, and 59.10-5. By means of this rule, we propose to remove the references at §§ 56.20-1 and 56.70-15. This portion of the ASME Boiler and Pressure Vessel Code (BPVC) provides rules for construction of power boilers, electric

• ASME Boiler and Pressure Vessel Code, Section IV, Rules for Construction of Heating Boilers (2019 edition). The 2004 edition is currently incorporated by reference at §§ 53.01-3, 53.01-5, 53.01-10, 53.05-1, 53.05-2, 53.05-3, 53.05-5, 53.10-1, 53.10-3, 53.10-10, 53.10-15, and 53.12-1. This code contains requirements, specific prohibitions, and non-mandatory guidance for construction of heating boilers. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the code. It is the internationally accepted authoritative standard for design and construction of heating boilers. Incorporating the latest editions ensures compliance with current industry practices. The 2019 code updates Section IV by adding stress values to Table HF-30001 and adding language to various parts to allow for electronic signatures

orate interpretations, and to clarify the intent of the code. It is the internationally accepted authoritative standard for design and construction of heating boilers. Incorporating the latest editions ensures compliance with current industry practices. The 2019 code updates Section IV by adding stress values to Table HF-30001 and adding language to various parts to allow for electronic signatures.

• ASME Boiler and Pressure Vessel Code, Section VII, Recommended Guidelines for the Care of Power Boilers (2019 edition). The 2001 edition is currently incorporated by reference at §§ 59.01-2. This code contains requirements, specific prohibitions, and non-mandatory guidance for construction of power boilers. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the code. It is the internationally accepted authoritative standard for operating, maintaining, examining, and care of power boilers. Incorporating the latest editions ensures compliance with current industry practices. The changes made to the standard are structural and stylistic. ASME Boiler and Pressure Vessel Code, Section VIII, Rules for Construction of Pressure Vessels (2019 edition). The 1998 edition is currently incorporated by reference at §§ 54.01-2, 54.01-5, 54.01-15, 54.01-18, 54.01-25, 54.01-30, 54.01-35, 54.03-1, 54.05-1, 54.10-1, 54.10-3, 54.10-5, 54.10-10, 54.10-15, 54.15-1, 54.15-5, 54.15-10, 54.15-13, 54.20-1, 54.20-3, 54.25-1, 54.25-3, 54.25-8, 54.25-10, 54.25-15, 54.25-20, 54.30-3, 54.30-5, 54.30-10, 56.15-1, 56.20-1, 56.25-5, 56.30-10, 56.30-30, 56.60-1, 56.60-2, 56.60-15, 56.95-10, 58.30-15, 59.10-5, and 59.10-10. By means of this rule, we propose to remove the references at §§ 54.01-15, 56.20-1, and 56.30-30. The 1989 edition is also incorporated by reference at §§ 64.5, 64.11, 64.13, 64.21, 64.25, and 64.31, and reference is made to the use of a constant from the 1974 edition in a calculation at § 64.63

-1, 56.25-5, 56.30-10, 56.30-30, 56.60-1, 56.60-2, 56.60-15, 56.95-10, 58.30-15, 59.10-5, and 59.10-10. By means of this rule, we propose to remove the references at §§ 54.01-15, 56.20-1, and 56.30-30. The 1989 edition is also incorporated by reference at §§ 64.5, 64.11, 64.13, 64.21, 64.25, and 64.31, and reference is made to the use of a constant from the 1974 edition in a calculation at § 64.63. However, these earlier editions would remain unchanged within the CFR, as part 64 is applicable only to marine portable tanks for which the Coast Guard's Marine Safety Center (MSC) received an application on or before May 1, 1991. This code contains requirements, specific prohibitions, and non-mandatory guidance for construction of pressure vessels. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the code. It is the internationally accepted authoritative standard for design and construction of heating boilers. Incorporating the latest editions ensures compliance with current industry practices. The 2019 edition allows for additional design methods from Div. 2 to be used in Div. 1 by creating new appendix 46. Revisions were also made for clarity.

• ASME Boiler and Pressure Vessel Code, Section IX, Welding, Brazing, and Fusing Qualifications (2019 edition). This standard updates the 1989 edition currently incorporated at §§ 56.70-5, 56.70-20, 56.75-2, 57.01-1, 57.01-1,57.02-2, 57.02-3, 57.02-4, 57.03-1, 57.04-1, 57.05-1, 57.06-1, 57.06-3, 57.06-4, and 59.10-5. By means of this rule, we propose to newly incorporate this standard at § 56.85-10 and to remove the references at §§ 57.01-1, 57.02-3, and 57.06-3

ng, and Fusing Qualifications (2019 edition). This standard updates the 1989 edition currently incorporated at §§ 56.70-5, 56.70-20, 56.75-2, 57.01-1, 57.01-1,57.02-2, 57.02-3, 57.02-4, 57.03-1, 57.04-1, 57.05-1, 57.06-1, 57.06-3, 57.06-4, and 59.10-5. By means of this rule, we propose to newly incorporate this standard at § 56.85-10 and to remove the references at §§ 57.01-1, 57.02-3, and 57.06-3. This standard establishes the qualifications of welders, welding operators, brazers, and brazing operators and the procedures employed in welding or brazing, and has been regularly revised to accommodate technological developments, address administrative requirements, incorporate interpretations, and clarify the intent of the code. It is the internationally accepted authoritative standard for pressure vessels.

• ASME B1.1-2003 (reaffirmed 2008), Unified Inch Screw Threads (UN and UNR Thread Form). This standard updates the 1982 edition, incorporated by reference at §§ 56.25-20 and 56.60-1, and specifies the thread form, series, class, allowance, tolerance, and designation for unified screw threads. The revision changes some of the values in tables provided in the standard. These changes in value were the result of the application of consistent eight decimal and round rules established in ASME B1.30-1992.

• ASME B1.20.1-2013, Pipe Threads, General Purpose (Inch). This standard updates the 1983 edition incorporated by reference at § 56.60-1, and covers the dimensions and gauging of pipe threads. The revisions to the standard include editorial changes, changes in calculations and figures, and clarification of figures.

• ASME B1.20.3-1976, Dryseal Pipe Threads (Inch), January 1, 1976, reaffirmed 2013 (“ASME B1.20.3”), IBR approved for § 56.60-1. We are updating the reaffirmation date of this standard to conform with its most recent reaffirmation. This document primarily provides specific dimensions for tapered pipe threads of various common sizes, and has not changed substantially

and clarification of figures.

• ASME B16.1-2015, Gray Iron Pipe Flanges and Flanged Fittings, Classes 25, 125, and 250. This standard updates the 1998 standard for these fittings as incorporated by reference in §§ 56.60-1 and 56.60-10. It covers pressure-temperature ratings, markings, and materials for Classes 25, 125, and 250 gray iron pipe flanges and flanged fittings. Updates include editorial changes, revisions and corrections to the 1998 edition.

• ASME B16.3-2016, Malleable Iron Threaded Fittings, Classes 150 and 300. This standard updates the 1998 edition incorporated by reference at § 56.60-1, and covers pressure-temperature ratings, dimensions, markings, and materials for Classes 150 and 300 malleable iron threaded fittings. Updates to the standard are editorial in nature, with changes made to update verbiage and readings.

• ASME B16.4-2016, Gray Iron Threaded Fittings, Classes 125 and 250.

• ASME B16.5-2017, Pipe Flanges and Flanged Fittings, NPS 1/2 through NPS 24 Metric/Inch Standard. This standard updates the 2003 edition incorporated by reference at §§ 56.25-20, 56.30.10, and 56.60-1. It covers pressure-temperature ratings, materials, dimensions, tolerances, marking, testing, and methods of designing openings for pipe flanges and flanged fittings. The updates made to this standard include updating materials and requirements for forgings.

pe flanges and flanged fittings. The updates made to this standard include updating materials and requirements for forgings.

• ASME B16.11-2016, Forged Fittings, Socket-Welding and Threaded. This standard updates the 2001 edition incorporated by reference at §§ 56.30-5 and 56.60-1. It covers pressure-temperature ratings, materials, dimensions, tolerances, marking, and testing for forged fittings. Updates to the standard include the addition of another type of fitting, format and reference revisions, and marking requirements.

• ASME B16.14-2013, Ferrous Pipe Plugs, Bushings, and Locknuts with Pipe Threads. This standard updates the 1991 edition incorporated by reference at § 56.60-1. It covers pressure-temperature ratings, materials, dimensions, tolerances, marking, testing, and threading for various threaded ferrous pipe fittings. The updates to this standard were mostly editorial and conforming in nature, with revisions to section 8 requiring threads and gauging practices to conform to ASME B1.20.1 and other B16 standards.

• ASME B16.15-2013, Cast Copper Alloy Threaded Fittings, Classes 125 and 250. This standard updates the 1985 edition that is currently incorporated by reference at § 56.60-1. It covers pressure-temperature ratings, materials, dimensions, tolerances, marking, testing, and threading requirements for Classes 125 and 250 of cast copper alloy fittings. The standard was updated in 2004, and 2011, and the 2013 edition revises section 7, requiring threading and gauging practices be identical to ASME B1.20.1 and other B16 standards.

• ASME B16.20-2012, Metallic Gaskets for Pipe Flanges, Ring-Joint, Spiral-Wound, and Jacketed. This standard updates the 1998 edition incorporated by reference at § 56.60-1. It covers materials, dimensions, tolerances, and markings for metal ring-joint gaskets, spiral-wound metal gaskets, metal-jacketed gaskets, and grooved metal gaskets with covering layers

ASME B1.20.1 and other B16 standards.

• ASME B16.21-2016, Nonmetallic Flat Gaskets for Pipe Flanges. This standard updates the 2005 edition incorporated by reference at § 56.60-1. It covers types, sizes, materials, and dimensions for gaskets used with flanges. The 2016 edition primarily expands the scope of the standard to include values greater than size 12 NPS.

• ASME B16.23-2016, Cast Copper Alloy Solder Joint Drainage Fittings: DWV. This standard updates the 2002 edition incorporated by reference at § 56.60-1. It covers materials, dimensions, tolerances, and markings for cast copper alloy solder joint drainage fittings, designed for use in drain, waste, and vent systems. The updates in the 2016 edition are editorial in nature, with updates to verbiage and readings.

• ASME B16.25-2012, Buttwelding Ends. This standard updates the 2003 edition incorporated by reference at §§ 56.30-5, 56.60-1, and 56.70-10. It covers the preparation of buttwelding ends of piping components to be joined into a piping system by welding and includes requirements for welding bevels, for external and internal shaping of heavy-wall components, and for preparation of internal ends (including dimensions and tolerances). The updates to the standard are editorial in nature, and include updated reference and tables.

• ASME B16.29-2012, Wrought Copper Alloy Solder-Joint Drainage Fittings-DWV. This standard updates the 2007 edition currently incorporated at § 56.60-1

welding bevels, for external and internal shaping of heavy-wall components, and for preparation of internal ends (including dimensions and tolerances). The updates to the standard are editorial in nature, and include updated reference and tables.

• ASME B16.29-2012, Wrought Copper Alloy Solder-Joint Drainage Fittings-DWV. This standard updates the 2007 edition currently incorporated at § 56.60-1. This standard covers the materials, marking, sizes, and dimensions for wrought copper and copper alloy solder-joint drainage fittings, and was updated editorially in 2012.

• ASME B16.34-2017, Valves—Flanged, Threaded, and Welding End. This standard updates the 1996 edition currently incorporated by reference at §§ 56.20-1 and 56.60-1, though we propose to remove the reference at § 56.20-1 through this rule. This standard applies to new construction and covers pressure-temperature ratings, dimensions, tolerances, materials, testing and marking for flanged, threaded, and welding end valves. The standard updates the materials manufactured list to include valves up to NPS 60 and changes were made to allowable materials.

• ASME B18.2.1-2012, Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch Series). This standard updates the 1996 edition incorporated by reference at §§ 56.25-20 and 56.60-1. It covers the dimensional requirements for nine product types of inch series bolts and screws recognized as American National Standard. The 2012 standard provides significant revisions to illustrations in tables 6, 7 and 8 which provided the wrong dimensions for several figures.

• ASME B18.2.2-2015, Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Couplings Nuts (Inch Series). This standard updates the 1987 edition incorporated by reference at §§ 56.25-20 and 56.60-1. It covers complete general and dimensional data for various types of inch series hex and square nuts.

• ASME B31.1-2016, Power Piping, ASME Code for Pressure Piping, B31

• ASME B31.1-2016, Power Piping, ASME Code for Pressure Piping, B31. This standard updates the 2001 edition currently incorporated by reference at §§ 56.01-3, 56.01-5, 56.07-5, 56.07-10, 56.10-1, 56.10-5, 56.15-1, 56.15-5, 56.20-1, 56.25-7, 56.30-1, 56.30-5, 56.30-10, 56.30-20, 56.35-1, 56.50-1, 56.50-15, 56.50-40, 56.50-65, 56.50-70, 56.50-97, 56.60-1, 56.65-1, 56.70-10, 56.70-15, 56.80-5, 56.80-15, 56.95-1, 56.95-10, and 56.97-1. By means of this rule, we propose to add a new reference at § 56.70-5 and remove the existing references at §§ 56.15-5, 56.20-1, 56.30-10, 56.50-15, and 56.50-65. This standard prescribes requirements for the design, materials, fabrication, inspection, operation, and maintenance of piping systems. The updates to the standard were numerous, with many revisions to nomenclature and additions to stress test values for several items in various tables.

• ASME B31.3-2018, Process Piping, ASME Code for Pressure Piping, B31. This standard updates the 1987 edition currently incorporated by reference at § 58.60-7, and would also be adopted for § 56.60-1. ASME B31.3 is the industry standard for low temperature piping. It is a more appropriate reference for low temperature piping than ASME B31.1, which is the current main reference document for Part 56. A specific standard for low temperature piping is needed due to the increase in liquefied natural gas (LNG) as a ship fuel. LNG is cryogenic, necessitating the use of very specific materials.

• ASME B31.5-2016, Refrigeration Piping and Heat Transfer Components, ASME Code for Pressure Piping, B31. This standard updates the 1987 edition, incorporated by reference at § 58.20-5 and 58.20-20

Part 56. A specific standard for low temperature piping is needed due to the increase in liquefied natural gas (LNG) as a ship fuel. LNG is cryogenic, necessitating the use of very specific materials.

• ASME B36.10M-2015, Welded and Seamless Wrought Steel Pipe. This standard updates the 2004 edition incorporated by reference at §§ 56.07-5, 56.30-20, and 56.60-1. This standard covers the standardization of dimensions of welded and seamless wrought steel pipe for high or low temperatures and pressure. The 2015 edition updates the standard with editorial changes and revisions.

• ASME CSD-1-2018, Controls and Safety Devices for Automatically Fired Boilers. This standard updates the 2004 edition currently incorporated by reference at §§ 63.10-1, 63.15-1, and 63.20-1. This standard establishes requirements for the assembly, installation, maintenance, and operation of controls and safety devices on automatically operated boilers. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the standard. It is the internationally accepted authoritative standard on controls and safety devices for pressure vessels.

• ASME SA-675-2021, Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties. This standard replaces the 1998 edition currently incorporated at § 56.60-2. The standard is identical to ASTM A675 in that it covers special quality carbon steel bars and bar size shapes to specific mechanical properties, most importantly tensile strength. The current standard has minor technical differences from the 1998 edition, such as minor changes to maximum carbon content of certain steel grades

standard replaces the 1998 edition currently incorporated at § 56.60-2. The standard is identical to ASTM A675 in that it covers special quality carbon steel bars and bar size shapes to specific mechanical properties, most importantly tensile strength. The current standard has minor technical differences from the 1998 edition, such as minor changes to maximum carbon content of certain steel grades.

• ASTM A20/A20M-19, Standard Specification for General Requirements for Steel Plates for Pressure Vessels. The 1997 edition is currently incorporated by reference at §§ 54.05-10 and 54.25-10. This standard provides a group of common requirements that apply to rolled steel plates used for pressure vessels. It has been regularly updated to address advancements in steel plate chemical compositions, manufacturing processes, and material testing.

• ASTM A36/A36M-14, Standard Specification for Carbon Structural Steel. This standard updates the 1997 edition incorporated by reference at § 56.30-10. This standard covers “carbon steel shapes, plates, and bars of structural quality for use in rivet, bolted, or welded construction . . .for general purposes.” The updates to the standard include updates to material construction limits for plate products greater than 15 inches.

• ASTM A47A47M-99 (Reapproved 2014), Standard Specification for Ferritic Malleable Iron Castings. This standard updates the 1995 edition incorporated by reference at § 56.60-1. This standard, which covers ferritic malleable castings for general engineering usage at temperatures from normal ambient to approximately 400°C (750 °F), is routinely updated to reflect updates in technology and practices.

itic malleable castings for general engineering usage at temperatures from normal ambient to approximately 400°C (750 °F), is routinely updated to reflect updates in technology and practices.

• ASTM A53/A53M-12, Standard Specification for Pipe, Steel, Black and Hot Dipped, Zinc-Coated, Welded and Seamless. This standard updates the 1998 edition incorporated by reference at §§ 56.10-5 and 56.60-1. It covers seamless and welded black and hot-dipped galvanized steel pipes and is updated to reflect changes in material composition for copper content of a type of pipe, as well as some editorial changes.

• ASTM A126-04, Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings (Reapproved 2014). This standard updates the 1995 edition incorporated by reference at § 56.60-1. It covers three classes of gray iron for castings intended for use as valve pressure retaining parts, pipe fittings, and flanges and is updated to reflect changes in material testing.

• ASTM A135/A135M-19, Standard Specification for Electric-Resistance-Welded Steel Pipe. This standard updates the 1997 edition incorporated by reference at § 56.60-1. It covers two grades of electric-resistance-welded steel pipe in NPS 2 to NPS 30 wall thickness. The standard has been updated to reflect changes in material testing and some editorial changes.

• ASTM A193/A193M-19, Standard Specification for Alloy-Steel and Stainless Steel Bolting for High-Temperature Service or High Pressure Service and Other Special Purpose Applications. This updates the 1998 standard incorporated by reference at § 58.30-15. This standard covers alloy and stainless steel bolting materials and components for pressure vessels, valves, flanges, and fittings for high temperature or high-pressure service. The updates to this standard are editorial in nature with minor technical changes and changes in material testing and grading.

• ASTM A197/A197M-00 (Reapproved 2015), Standard Specification for Cupola Malleable Iron

15. This standard covers alloy and stainless steel bolting materials and components for pressure vessels, valves, flanges, and fittings for high temperature or high-pressure service. The updates to this standard are editorial in nature with minor technical changes and changes in material testing and grading.

• ASTM A197/A197M-00 (Reapproved 2015), Standard Specification for Cupola Malleable Iron. This standard updates the 1992 edition incorporated by reference at § 56.60-1. It covers malleable irons for castings made by the cupola process. The standard has been updated to reflect changes in material testing, as well as with some editorial changes.

• ASTM A203/A203M-17, Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel. The 1997 edition is currently incorporated by reference at § 54.05-20. This standard covers nickel-alloy steel plates intended for pressure vessels. It has been revised twice since 1997 to update the chemical composition requirements of nickel-alloy steel and to eliminate prescriptive “current practice” thickness limits. Instead, thickness is only limited by the capacity of the composition to meet specified mechanical properties.

• ASTM A210/A210M-19, Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes. This standard updates the 1996 edition incorporated by reference at § 56.60-1. It covers minimum-wall-thickness, seamless medium-carbon steel, boiler flues, including safe ends, arch and stay tubes, and superheater tubes and is updated to reflect changes in material testing and grading, as well as some editorial changes.

• ASTM A268/A268M-10 (Reapproved 2016), Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service. This standard updates the 1996 edition incorporated by reference at § 56.60-1. It covers minimum-wall-thickness, stainless steel tubing for general corrosion-resisting and high-temperature service

d grading, as well as some editorial changes.

• ASTM A276/A276M-17, Standard Specification for Stainless Steel Bars and Shapes. This standard updates the 1998 edition incorporated by reference at § 56.60-2. It covers hot-finished or cold-finished bars except bars for forging. The updated standard reflects changes in material testing and grading, as well as some editorial changes.

• ASTM A312/A312M-17, Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes. This standard updates the 1995 edition incorporated by reference at §§ 56.50-105 and 56.60-1. The standard covers overs seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service. The standard is updated to reflect changes in material testing and grading, as well as some editorial changes.

• ASTM A333/A333M-16, Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness. This standard updates the 1994 edition incorporated by reference at §§ 56.50-105 and 56.60-1. It covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures and in other applications requiring notch toughness and is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A334/A334M-04a (Reapproved 2016), Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service

nal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures and in other applications requiring notch toughness and is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A334/A334M-04a (Reapproved 2016), Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service. This standard updates the 1994 edition incorporated by reference at §§ 56.50-105 and 56.60-1. It covers nominal (average) wall seamless and welded carbon and alloy steel tubes intended for use at low temperatures and in other applications requiring notch toughness and is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A350/A350M-17, Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components. The standard updates the 1997 edition incorporated by reference at § 56.50-105. This standard covers several grades of carbon and low-alloy steel forged or ring-rolled flanges, forged fittings and valves intended primarily for low-temperature service and requiring notch toughness testing. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A352/A352M-17, Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature Service. The standard updates the 1998 edition incorporated by reference at § 56.50-105. This standard covers steel castings for valves, flanges, fittings, and other pressure-containing parts. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

s, and other pressure-containing parts. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A358/A358M-15, Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications. The standard updates the 1992 edition incorporated by reference at § 56.60-1. This standard covers the grades of alloy and stainless steel piping suitable for corrosive or high-temperature service. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A370-19, Standard Test Methods and Definitions for Mechanical Testing of Steel Products. The 1997 edition is currently incorporated by reference at § 54.25-20. This standard covers procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. It has been revised almost annually since 1997 to address advancements in testing technology and practices.

• ASTM A376/A376M-17, Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Service. The standard updates the 1998 edition incorporated by reference at §§ 56.60-1 and 56.60-2. This standard covers grades of hydrogen and nitrogen for seamless austenitic steel pipes made for high-temperature service. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A403/A403M-16, Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings. The standard updates the 1998 edition incorporated by reference at § 56.60-1. This standard covers wrought stainless steel fittings for pressure piping applications. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A420/A420M-16, Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service

ndard updates the 1998 edition incorporated by reference at § 56.60-1. This standard covers wrought stainless steel fittings for pressure piping applications. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A420/A420M-16, Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service. The standard updates the 1996 edition incorporated by reference at §§ 56.50-105 and 56.60-1. This standard covers fittings for use in pressure piping and pressure vessel service at low temperatures. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A522/A522M-14, Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service. The standard updates the 1995 edition incorporated by reference at § 56.50-105. This standard covers 8 or 9% nickel-alloy steel forged or rolled flanges, fittings, valves, and parts intended for use in welded pressure vessels for low-temperature service. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A575-96 (Reapproved 2013), Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades. The standard updates the 1996 (reapproved in 2007) edition incorporated by reference at § 56.60-2. This standard covers hot-wrought merchant quality steel bars produced to a chemical composition. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM A576-17, Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality. The standard updates the 1990 edition (reapproved in 2012) incorporated by reference at § 56.60-2. This standard covers hot-wrought special quality steel bars. The standard is updated to reflect editorial revisions and corrections

ct editorial revisions as well as changes in material grading and testing.

• ASTM B16/B16M-10 (Reapproved 2015), Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines. The standard updates the 1992 edition incorporated by reference at § 56.60-2. This standard establishes the requirements for free-cutting brass rod, bar, wire and shapes of any specified cross section produced from copper alloy suitable for high speed screw matching applications and moderate thread rolling. The standard is updated to reflect editorial revisions as well as changes in material composition, grading, and testing.

• ASTM B21/B21M-20, Standard Specification for Naval Brass Rod, Bar, and Shapes. The standard updates the 1996 edition incorporated by reference at § 56.60-2. It establishes the requirements for naval brass rod, bar, and shapes produced from copper alloy, including dimensions, workmanship and appearance, testing methods, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B26/B26-M-18, Standard Specification for Aluminum-Alloy Sand Castings. The standard updates the 1997 edition incorporated by reference at § 56.60-2. It covers specifications aluminum-alloy sand castings used in general purpose applications, including dimensions, workmanship and appearance, testing methods, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B42-20, Standard Specification for Seamless Copper Pipe, Standard Sizes. The standard updates the 1996 edition incorporated by reference at § 56.60-1

used in general purpose applications, including dimensions, workmanship and appearance, testing methods, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B42-20, Standard Specification for Seamless Copper Pipe, Standard Sizes. The standard updates the 1996 edition incorporated by reference at § 56.60-1. This standard covers the requirements for seamless copper pipe in all nominal or standard pipe sizes, both regular and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B43-15, Standard Specification for Seamless Red Brass

• ASTM B68/B68M-19, Standard Specification for Seamless Copper Tube, Bright Annealed. The standard updates the 1995 edition incorporated by reference at § 56.60-1. This standard covers the requirements for bright annealed seamless copper tube suitable for use in refrigeration, oil lines, and gasoline lines, where tubing with an interior surface free from scale and dirt is required. This standard was also updated in 2011. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B75/B75M-19, Standard Specification for Seamless Copper Tube. The standard updates the 1997 edition incorporated by reference at § 56.60-1. This standard establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications. This standard was also updated in 2011. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B85/B85M-18, Standard Specification for Aluminum-Alloy Die Castings. The standard updates the 1996 edition incorporated by reference at § 56.60-2

seamless round, rectangular, and square copper tube suitable for general engineering applications. This standard was also updated in 2011. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B85/B85M-18, Standard Specification for Aluminum-Alloy Die Castings. The standard updates the 1996 edition incorporated by reference at § 56.60-2. It covers aluminum alloy die castings for use in general purpose applications, including dimensions, workmanship and appearance, testing methods, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B96/B96M-16, Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels. The standard updates the 1993 edition incorporated by reference at §§ 56.60-2 and 58.50-5. This standard establishes requirements for copper-silicon alloy plate, sheet, strip, and rolled bar for drawing, forming, stamping, bonding, and general engineering applications. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B111/B111M-18a, Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock. The standard updates the 1995 edition incorporated by reference at § 56.60-1. It establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions in the tables provided in the standard.

re, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions in the tables provided in the standard.

• ASTM B122/B122M-16, Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar. This updates the 1998 standard incorporated by reference at § 58.50-5. This standard establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar, including testing methods, material and manufacture, mechanical properties, and performance requirements. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM B124/B124M-18, Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes. The standard updates the 1996 edition incorporated by reference at § 56.60-2. It establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B127-19, Standard Specification for Nickel-Copper Alloy Plate, Sheet, and Strip. This updates the 1993 standard incorporated by reference at §§ 58.50-5 and 58.50-10. This standard covers the requirements for rolled nickel-copper alloy plate, sheet, and strip including testing methods, material and manufacture, mechanical properties, and performance requirements. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM B152/B152M-19, Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar. This updates the 1997 standard incorporated by reference at § 58.50-5

ip including testing methods, material and manufacture, mechanical properties, and performance requirements. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM B152/B152M-19, Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar. This updates the 1997 standard incorporated by reference at § 58.50-5. This standard covers the requirements for copper sheet, strip, plate, and rolled bar, including testing methods, material and manufacture, mechanical properties, and performance requirements. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM B161-05 (Reapproved 2019), Standard Specification for Nickel Seamless Pipe and Tube. The standard updates the 1993 edition incorporated by reference at § 56.60-1. It covers the requirements for nickel and low-carbon nickel in the form of cold-worked seamless pipe and tubes, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B165-19, Standard Specification for Nickel-Copper Alloy Seamless Pipe and Tube. The standard updates the 1993 edition incorporated by reference at § 56.60-1. It covers the requirements for nickel-copper alloy in the form of cold-worked seamless pipe and tubes, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing

d Tube. The standard updates the 1993 edition incorporated by reference at § 56.60-1. It covers the requirements for nickel-copper alloy in the form of cold-worked seamless pipe and tubes, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B167-18, Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS N06235) Seamless Pipe and Tube. The standard updates the 1997 edition incorporated by reference at § 56.60-1. The standard covers cold-worked annealed, hot worked, annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B171/B171M-18, Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers. The standard updates the 1995 edition incorporated by reference at § 56.60-2. It covers the requirements for copper-alloy plate, sheet, and circles cut from plate and sheet for pressure vessels, condensers, and heat exchangers, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B209-14, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate. This updates the 1996 standard incorporated by reference at §§ 58.50-5 and 58.50-10

t exchangers, including testing methods, material and manufacture, mechanical properties, and performance requirements. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B209-14, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate. This updates the 1996 standard incorporated by reference at §§ 58.50-5 and 58.50-10. This standard covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate, including testing methods,

• ASTM B210/B210M-19a, Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes. The standard updates the 1995 edition incorporated by reference at § 56.60-1. It covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose and pressure application in alloys. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B234-17, Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers. This standard updates the 1995 standard incorporated by reference at § 56.60-1. It covers aluminum-alloy drawn seamless round tube in straight lengths for use in surface condensers, evaporators, and heat exchangers. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B241/B241M-16, Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube. The standard updates the 1996 edition incorporated by reference at § 56.60-1. It covers aluminum and aluminum-alloy seamless pipe intended for pressure applications, and outlines the standard sizes and tempers necessary. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B280-18, Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service

ated by reference at § 56.60-1. It covers aluminum and aluminum-alloy seamless pipe intended for pressure applications, and outlines the standard sizes and tempers necessary. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B280-18, Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service. The standard updates the 1997 edition incorporated by reference at § 56.60-1. This standard establishes the requirements for seamless copper tube intended for use in the connection, repairs, or alterations of air conditioning or refrigeration units in the field. The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B283/B283M-18, Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed). The standard updates the 1996 edition incorporated by reference at § 56.60-2. This standard establishes the requirements for copper and copper alloy die forgings produced by the hot pressing method. The standard is updated to reflect editorial revisions as well as changes in chemical compositions and material grading and testing.

• ASTM B315-19, Standard Specification for Seamless Copper Alloy Pipe and Tube. The standard updates the 1993 edition incorporated by reference at § 56.60-1. This standard establishes the requirements for seamless copper alloy tube intended for general engineering purposes. The standard is updated to reflect editorial revisions.

• ASTM B361-16, Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings. The standard updates the 1995 edition, incorporated by reference at § 56.60-1. It covers factory-made wrought aluminum and aluminum-alloy welding fittings (butt-welding or socket-end parts). The standard is updated to reflect editorial revisions as well as changes in material grading and testing

B361-16, Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings. The standard updates the 1995 edition, incorporated by reference at § 56.60-1. It covers factory-made wrought aluminum and aluminum-alloy welding fittings (butt-welding or socket-end parts). The standard is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM B858-06 (Reapproved 2018), Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys. The standard updates the 1995 edition, incorporated by reference at § 56.60-2. This test method describes a procedure to determine the presence of residual stress in wrought copper alloy products that may lead to stress corrosion cracking. The standard is updated to reflect editorial revisions as well as changes in material testing.

• ASTM D92-18, Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester. This updates the 1997 standard incorporated by reference at § 58.30-10. The standard describes the determination of the flash point and fire point of petroleum products by manual or automated Cleveland open cup apparatus. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM D93-19, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester. This updates the 1997 standard incorporated by reference at § 58.01-10. These test methods cover the determination of the flash point of petroleum products in the temperature range from 40 °C to 370 °C by manual or automated Pensky-Martens closed-cup apparatus. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM D323-15a, Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method). This updates the 1994 standard incorporated by reference at § 58.16-5

s in the temperature range from 40 °C to 370 °C by manual or automated Pensky-Martens closed-cup apparatus. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM D323-15a, Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method). This updates the 1994 standard incorporated by reference at § 58.16-5. This standard covers test method procedures for the determination of vapor pressure of gasoline, volatile crude oil, and other volatile petroleum products. The updates to this standard are editorial in nature with minor technical changes, or changes in material testing and grading.

• ASTM D665-19, Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water. This standard updates the standard from 1998, incorporated by reference at § 61.20-17. It covers test methods evaluating the ability of inhibited mineral oils, particularly steam-turbine oils, to aid in rust prevention of ferrous parts. The edits to this standard are editorial in nature.

• ASTM E23-18, Standard Test Methods for Notched Bar Impact Testing of Metallic Materials. The standard updates the 1996 edition, incorporated by reference at §§ 54.05-5 and 56.50-105. This test method describes notched-bar impact testing of metallic materials. The standard is updated to reflect editorial revisions as well as changes in material testing.

• ASTM E208-19, Standard Test Method for Conducting Drop-Weight Test to Determine Nil-Ductility Transition Temperature of Ferritic Steels. The standard updates the 1995 edition, currently incorporated by reference at § 54.05-5. This standard describes methods of determining nil-ductile transition (NDT) of ferritic steels. It has been revised three times since 1995 to address advancements in testing methods.

• ASTM F1006-86 (Reapproved 2018), Standard Specification for Entrainment Separators for Use in Marine Piping Applications

ls. The standard updates the 1995 edition, currently incorporated by reference at § 54.05-5. This standard describes methods of determining nil-ductile transition (NDT) of ferritic steels. It has been revised three times since 1995 to address advancements in testing methods.

• ASTM F1006-86 (Reapproved 2018), Standard Specification for Entrainment Separators for Use in Marine Piping Applications. The standard updates the 1986 edition (reapproved in 2008), incorporated by reference at § 56.60-1. It covers the minimum requirements for the pressure-temperature rating, testing, and making of pressure-containing vessels for entrainment separators and is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM F1007-18, Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application. This standard updates the 1986 edition (reapproved in 2007), incorporated by reference at § 56.60-1. It covers the design, manufacturing, and testing of packed slip tube expansion joints used in pipelines for thermal growth and contraction and is updated to reflect editorial revisions as well as changes in material grading and testing.

• ASTM F1020-86 (Reapproved 2018), Standard Specification for Line-Blind Valves for Marine Applications.

• ASTM F1120-87 (Reapproved 2015), Standard Specification for Circular Metallic Bellows Type Expansion Joints for Piping Applications. This standard reapproves the 1987 edition (reapproved last in 2010), incorporated by reference at § 56.60-1. It establishes the requirements for design, manufacture, inspection, and testing of circular metallic bellows-type expansion joints for piping applications.

incorporated by reference at § 56.60-1. It establishes the requirements for design, manufacture, inspection, and testing of circular metallic bellows-type expansion joints for piping applications.

• ASTM F1123-87 (Reapproved 2015), Standard Specification for Non-Metallic Expansion Joints. This standard reapproves the 1987 edition (reapproved last in 2010), incorporated by reference at § 56.60-1. It provides the minimum requirements for construction, materials, performance, and dimensional requirements of arch-type non-metallic expansion joints.

• ASTM F1139-88 (Reapproved 2015), Standard Specification for Steam Traps and Drains. This standard reapproves the 1988 edition (reapproved last in 2010), incorporated by reference at § 56.60-1. This standard provides the minimum requirements for the design, fabrication, pressure rating, marking, and testing of steam traps and drains.

• ASTM F1155-10 (Reapproved 2015), Standard Practice for Selection and Application of Piping System Materials. ASTM F1155 already specifies a list of acceptable material and design standards for many shipboard systems. This standard is currently not incorporated by reference in 46 CFR part 56, and would be incorporated by reference in §§ 56.50-60, 56.50-105, 56.60-1, and 56.60-15. Incorporating F1155 would enable the removal of the following standards from Part 56:

○ ASME B16.9, Factory-Made Wrought Steel Buttwelding Fittings.

○ ASME B16.10, Face-to-Face and End-to-End Dimensions of Valves.

○ ASME B16.18, Cast Copper Alloy Solder Joint Pressure Fittings.

○ ASME B16.22, Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings.

○ ASME B16.24, Cast Copper Alloy Pipe Flanges, Flanged Fittings, and Valves Classes 150, 300, 600, 900, 1500, and 2500.

○ ASME B16.42, Ductile Iron Pipe Flanges and Flanged Fittings Classes 150 and 300.

○ ASTM A106/A106M, Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service

ittings.

○ ASME B16.22, Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings.

○ ASME B16.24, Cast Copper Alloy Pipe Flanges, Flanged Fittings, and Valves Classes 150, 300, 600, 900, 1500, and 2500.

○ ASME B16.42, Ductile Iron Pipe Flanges and Flanged Fittings Classes 150 and 300.

○ ASTM A106/A106M, Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service.

○ ASTM A139/A139M, Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over).

○ ASTM A182/A182M, Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service.

○ ASTM A192/A192M, Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service.

○ ASTM A194/A194M, Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both.

○ ASTM A213/A213M, Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes.

○ ASTM A214/A214M, Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes.

○ ASTM A234/A234M, Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service.

○ ASTM A249/A249M, Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes.

○ ASTM A307, Standard Specification for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength.

○ ASTM A320/A320M, Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service.

○ ASTM A335/A335M, Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service.

○ ASTM A351/A351M, Standard Specification for Castings, Austenitic, for Pressure-Containing Parts.

○ ASTM A395/A395M, Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures

d by reference at § 56.60-1. It covers reinforced thermosetting resin pipe systems with nominal pipe sizes 1 through 48 in. (25 through 1200 mm). The update reflects editorial revisions as well as changes in material grading and testing.

• ASTM F1199-88 (Reapproved 2015), Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150 °F Maximum). This standard reapproves the 1988 edition (reapproved last in 2010) incorporated by reference at § 56.60-1. It covers the minimum requirements for the design, fabrication, rating, marking, and testing of cast and welded pipe line strainers.

• ASTM F1200-88 (Reapproved 2016), Standard Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150 °F). This standard reapproves the 1988 edition (reapproved last in 2010), incorporated by reference at § 56.60-1. It covers the minimum requirements for the design, fabrication, rating, marking, and testing of welded pipe line strainers.

• ASTM F1201-88 (Reapproved 2016), Standard Specification for Fluid Conditioner Fittings in Piping Applications above 0 °F. This standard reapproves the 1988 edition (reapproved last in 2010), incorporated by reference at § 56.60-1. It provides the minimum requirements for pressure-retaining components of fluid conditioner fittings. It addresses the pressure-retaining component design, fabrication, rating, marking, and testing.

• ASTM F1323-14, Standard Specification for Shipboard Incinerators. This standard updates the 2001 standard currently incorporated by reference at § 63.25-9. It establishes requirements for design, manufacture, performance, operation, functioning, and testing of shipboard incinerators and has been regularly revised to accommodate technological

t § 63.25-9. It establishes requirements for design, manufacture, performance, operation, functioning, and testing of shipboard incinerators and has been regularly revised to accommodate technological

• ASTM F1387-19, Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings. This standard updates the 1993 edition currently incorporated by reference at § 56.30-25. The standard covers performance characteristics required for mechanically attached fillings used in piping and tubing systems. The changes made to the standard include updates to references, deleting cancelled United States Military Specifications and Standards, corrections to notes and tables, and clarifications on required testing.

• ASTM F1476-07 (Reapproved 2013), Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications. This standard reapproves the 2007 edition, which updated the 1995 edition incorporated by reference at § 56.30-35. The specification provides the performance characteristics and qualification tests required for gasketed mechanical couplings, including grooved-type mechanical couplings for grooved end pipe. The changes made to the standard in 2007 were editorial in nature, and with some changes to material testing and grading.

• ASTM F1548-01 (Reapproved 2018), Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications. This standard reapproves the 2001 edition, which updated the 1994 edition incorporated by reference at § 56.30-35. It defines classification, materials, test requirements, inspection certification, marking and packing of fittings for use with gasketed mechanical couplings. The changes made to the standard in 1999 were editorial in nature, with some changes to material testing and grading.

• Compressed Gas Association (CGA) standard CGA S-1.2-2009, Pressure Relief Device Standards—Part 2—Portable Containers for Compressed Gases

cation, materials, test requirements, inspection certification, marking and packing of fittings for use with gasketed mechanical couplings. The changes made to the standard in 1999 were editorial in nature, with some changes to material testing and grading.

• Compressed Gas Association (CGA) standard CGA S-1.2-2009, Pressure Relief Device Standards—Part 2—Portable Containers for Compressed Gases. The 1979 edition is currently incorporated by reference at § 54.15-10. This standard covers the recommended minimum requirements for pressure relief devices used on portable containers for compressed gases that comply with regulations of the U.S. Department of Transportation or the corresponding regulations of Transport Canada. It has been revised at least five times since 1979 to address advancements in technology and changes in U.S. and Canadian regulations.

• Standards of the Expansion Joint Manufacturers Association, Tenth Edition (2015). This edition replaces the 1980 edition currently incorporated in § 56.60-1. This standard specifies the design and manufacturing requirements for expansion joints, including metallic bellows type, used in piping systems to accommodate pipe movements due to temperature expansion/contraction, and slight misalignments in joined piping sections.

• Fluid Controls Institute Inc. (FCI), FCI 69-1, Pressure Rating Standard for Steam Traps, 2017. The 2017 edition replaces the edition currently incorporated at § 56.60-1. This standard covers the minimum design, fabrication, pressure rating and marking of pressure-containing housings for steam traps. Revisions to this document consist mainly of editorial changes and modifications to definitions.

ressure-containing housings for steam traps. Revisions to this document consist mainly of editorial changes and modifications to definitions.

• International Convention for Safety of Life at Sea (SOLAS), 1974 as amended. This standard is not currently codified within 46 CFR part 56 or part 58, though its applicability to passenger vessels on international voyages is mentioned in § 56.50-50(c)(2). However, the CFR codifies language taken directly from SOLAS in a number of places in Titles 33 and 46 CFR. Incorporating specific SOLAS regulations by reference, in § 56.50-50 for bilge systems and § 58.25-10 for steering gear, would allow for an alternative to the prescriptive technical requirements of the CFR. SOLAS is an international maritime treaty that sets minimum safety standards in the construction, equipment, and operation of merchant ships. This requires no updates, merely the adoption of a standard already in place in practice.

• IMO Resolution MEPC.244(66), Standard Specification for Shipboard Incinerators, 2014. This document is proposed for addition as an alternate method of compliance to the requirements for shipboard incinerators in § 63.25-9. IMO MEPC.244(66) is the IMO's updated standard for shipboard incinerator design, defining the engineering requirements and environmental air emissions limits for ship incinerators.

• IMO Resolution MSC.337(91), Code on Noise Levels on Board Ships, 2012. This document replaces the older IMO Resolution A.468(XII), Code on Noise Levels on Board Ships, incorporated by reference in § 58.01-50. The Code on Noise Levels on Board Ships is intended to provide standards to prevent and mitigate the occurrence of hazardous noise levels on board ships, and to provide standards for an acceptable working and living environment for seafarers. The 2012 Code on Noise Levels on Board Ships reflects technology improvements and mandatory requirements not included in the older IMO Resolution, and is intended to provide the basis for a design standard

ded to provide standards to prevent and mitigate the occurrence of hazardous noise levels on board ships, and to provide standards for an acceptable working and living environment for seafarers. The 2012 Code on Noise Levels on Board Ships reflects technology improvements and mandatory requirements not included in the older IMO Resolution, and is intended to provide the basis for a design standard.

• ISO 9096:2017(E), Stationary source emissions—Manual determination of mass concentration of particulate matter. This standard updates the 2003 edition currently incorporated by reference at § 63.25-9. This standard establishes methods for measurement of particulate matter concentration in waste gases. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

• ISO 13617:2019(E), Ships and marine technology—Shipboard incinerators—Requirements. This standard updates the 2001 edition currently incorporated by reference at § 63.25-9. This standard establishes design, manufacture, performance, operation, functioning and testing of incinerators. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

• ISO 15540:2016(E), Ships and marine technology—Fire resistance of non-metallic hose assemblies and non-metallic compensators—Test methods. This standard replaces the 1999 edition currently incorporated in § 56.60-25. It specifies the temperatures, duration, and pressure testing associated with fire tests used to qualify nonmetallic hose for use in ship piping systems.

ntly incorporated in § 56.60-25. It specifies the temperatures, duration, and pressure testing associated with fire tests used to qualify nonmetallic hose for use in ship piping systems.

• Manufacturers Standardization Society of the Valve and Fitting Industry, Inc. (MSS) standard MSS SP-6-2017, Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings. This standard updates the 2001 edition, incorporated by reference at §§ 56.25-10 and 56.60-1. This standard pertains to the finish of gasket contact faces of pipe flanges and connecting-end flanges of valves and fittings. The changes made to the standard were largely editorial in nature; however there are also some changes to definitions and material limitations.

• MSS SP-9-2013, Spot Facing for Bronze, Iron, and Steel Flanges. This standard updates the 2001 edition, incorporated by reference at § 56.60-1. It applies to the spot facing for U.S. customary bolting of pipe flanges in

• MSS SP-25 (ANSI/MSS SP-25-2018), Standard Marking System for Valves, Fittings, Flanges and Unions. The 1998 edition is currently incorporated by reference at § 54.01-25, while the 2001 edition is incorporated by reference at §§ 56.15-1, 56.20-5, and 56.60-1. This standard provides a marking system for new valves, fittings, flanges, and unions used in piping connections that include (but are not limited to) flanged, soldered, brazed, threaded, or welded joints. Markings are used for product identification and to assist in proper application. The standard has been revised three times since 1998 to address changes in industry practices.

• MSS SP-51-2012, Class 150LW Corrosion Resistant Flanges and Cast Flanged Fittings. This standard updates the 2003 edition, incorporated by reference at § 56.60-1. This standard establishes the design dimensions, tolerances, and pressure-temperature ratings for flanged steel fittings for both Metric and Imperial units

been revised three times since 1998 to address changes in industry practices.

• MSS SP-53-2012, Quality Standard for Steel Castings and Forgings for Valves, Flanges, Fittings, and Other Piping Components—Magnetic Particle Examination Method. This standard updates the 1995 edition, incorporated by reference at § 56.60-1. It provides methods and acceptance standards for magnetic particle examination of ferritic steel valves, flanges, fittings, and other piping components by use of dry magnetic powder or wet magnetic particles. The changes made to the standard are editorial in nature, with some changes to material testing, design and grading.

• MSS SP-55 (ANSI/MSS-SP-55-2011), Quality Standard for Steel Castings for Valves, Flanges and Fittings and Other Piping Components—Visual Method for Evaluation of Surface Irregularities. This standard updates the 2001 edition, incorporated by reference at § 56.60-1. The document describes common irregularities found in the castings of steel pipe fittings and flanges, as well as acceptable criteria for evaluating irregularities. The changes made to the standard are editorial in nature, with some changes to material testing, design and grading.

• MSS SP-58 (ANSI/MSS SP-58-2009), Pipe Hangers and Supports—Materials, Design, Manufacture, Selection, Application, and Installation. This standard updates the 1993 edition, incorporated by reference at § 56.60-1. MSS-SP-58 specifies the design criteria and minimum strength requirements for hangars used to mount piping systems to ship bulkheads and decks. The changes made to the standard are editorial in nature, with some changes to material testing, design and grading

sign, Manufacture, Selection, Application, and Installation. This standard updates the 1993 edition, incorporated by reference at § 56.60-1. MSS-SP-58 specifies the design criteria and minimum strength requirements for hangars used to mount piping systems to ship bulkheads and decks. The changes made to the standard are editorial in nature, with some changes to material testing, design and grading.

• MSS SP-61-2019, Pressure Testing of Valves. This standard updates the 2003 edition incorporated by reference at § 56.60-1. The document provides standardized technical requirements and acceptance criteria for the pressure testing of valves.

• National Fire Protection Association (NFPA) standard NFPA 302, Fire Protection Standard for Pleasure and Commercial Motor Craft, 2020 Edition. This standard provides the minimum requirements on boats for the prevention of fire and explosion, mitigation of carbon monoxide hazards, and life safety in case of fire. It updates the 1989 standard incorporated by reference at § 58.10-5. The updates to this standard are editorial in nature with minor technical changes, and changes in material testing and grading.

• SAE International (SAE) standard SAE J429 MAY2014, Mechanical and Material Requirements for Externally Threaded Fasteners. This standard updates the 1989 standard incorporated by reference at § 58.30-15. It covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for screw-and-washer assemblies, and U-bolts.The updates to this standard are editorial in nature with minor technical changes, and changes in material testing and grading.

• SAE J1475 JUN2014, Hydraulic Hose Fittings for Marine Applications. This standard updates the 1996 edition currently incorporated in § 53.01-10. It covers the materials, design, and testing requirements for fittings used with flexible hose assemblies for use in ship piping systems

o this standard are editorial in nature with minor technical changes, and changes in material testing and grading.

• SAE J1928 JUN2018, Devices Providing Backfire Flame Control for Gasoline Engines in Marine Applications. This standard updates the 1989 standard incorporated by reference at § 58.10-5. It covers the minimum requirements for design, construction, and testing of devices to prevent the propagation of backfire flame from a gasoline engine to the surrounding atmosphere. The updates to this standard are editorial in nature with minor technical changes, and changes in material testing and grading.

• SAE J1942 MAR2019, Hose and Hose Assemblies for Marine Applications. This standard updates the 1997 edition currently incorporated in § 56.60-25. It defines the design and testing requirements, including fire tests, for non-metallic flexible hose assemblies used in shipboard piping systems. Changes to this standard are administrative in nature, including updated testing frequency and record retention requirements.

• Underwriters Laboratories (UL) standard UL 174, Standard for Safety, Household Electric Storage Tank Water Heaters, Eleventh Edition, 2004 (reapproved in 2016). The 1996 edition is currently incorporated by reference at §§ 53.01-10 and 63.25-3. This standard contains requirements and non-mandatory guidance for household electric storage tank water heaters. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the standard

roved in 2016). The 1996 edition is currently incorporated by reference at §§ 53.01-10 and 63.25-3. This standard contains requirements and non-mandatory guidance for household electric storage tank water heaters. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the intent of the standard. Incorporating the latest edition ensures compliance with current industry practices.

• UL 296, UL Standard for Safety Oil Burners, 11th Edition (“2017 UL 296”). This standard updates the 1993 edition currently incorporated by reference at § 63.15-5. This standard establishes requirements for oil burners intended for firing appliances and devices such as boilers, central, floor, wall, and special furnaces, storage tank water, air, and direct-fired air heater units. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

• UL 343, UL Standard for Safety Pumps for Oil-Burning Appliances, 2008. This standard updates the 1997 edition currently incorporated by reference at § 63.15-3. This standard establishes requirements for pumps intended for use as part of oil-burning appliances or installed in fuel-oil piping systems serving equipment. It has been regularly revised to accommodate technological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

ological developments, to address administrative requirements, to incorporate interpretations, and to clarify the standard intent. It is the internationally accepted standard.

• UL 1453, Standard for Safety, Electric Booster and Commercial Storage Tank Water Heaters, Sixth Edition, 2016. This standard would replace the 1995 standard, currently incorporated by reference at §§ 53.01-10 and 63.25-3. This standard contains requirements for electric booster water heaters, electric commercial storage tank water heaters, and remote control assemblies for such heaters, rated 600 volts or less, that are over 120 gallons

C. Standards Previously Approved for Incorporation by Reference

The following standards were previously approved for incorporation by reference and are included in the proposed regulatory text because either the current format of the reference does not comply with current OFR requirements or the proposed text is a revision that includes an existing reference to the standard. We do not propose to change the existing IBR approval.

• ASME B36.19M-2004 Stainless Steel Pipe, October 25, 2004 (“ASME B36.19M”), IBR approved for §§ 56.07-5 and 56.60-1.

• IMO A.467(XII), Guidelines for Acceptance of Non-Duplicated Rudder Actuators for Tankers, Chemical Tankers and Gas Carriers of 10,000 Tons Gross Tonnage and Above But Less Than 100,000 Tonnes Deadweight, 1981 (“IMO A.467(XII)”), IBR approved for § 58.25-60.

• IMO Resolution A.753(18) Guidelines for the Application of Plastic Pipes on Ships, adopted on 4 November 1993 (“IMO Resolution A.753(18)”), IBR approved for § 56.60-25.

• IMO Resolution MEPC.76(40), Standard Specification for Shipboard Incinerators (Sep. 25, 1997) (“IMO MEPC.76(40)”), IBR approved for § 63.25-9.

• IMO Resolution MSC.313(88), Amendments to the Guidelines for the Application of Plastic Pipes on Ships, adopted 26 November 2010 (“IMO Resolution MSC.313(88)”), IBR approved for § 56.60-25

3 (“IMO Resolution A.753(18)”), IBR approved for § 56.60-25.

• IMO Resolution MEPC.76(40), Standard Specification for Shipboard Incinerators (Sep. 25, 1997) (“IMO MEPC.76(40)”), IBR approved for § 63.25-9.

• IMO Resolution MSC.313(88), Amendments to the Guidelines for the Application of Plastic Pipes on Ships, adopted 26 November 2010 (“IMO Resolution MSC.313(88)”), IBR approved for § 56.60-25.

• The International Convention for the Prevention of Pollution from Ships (MARPOL 73/78), Annexes I, II, III, and V (1978) (“IMO MARPOL 73/78”), IBR approved for § 63.25-9.

• ISO 10396, Stationary source emissions—Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems, Second edition (Feb. 1, 2007) (“ISO 10396”), IBR approved for § 63.25-9.

• MSS SP-45-2003, Bypass and Drain Connections, 2003 (“MSS SP-45”), IBR approved for §§ 56.20-20 and 56.60-1.

D. Section by Section Analysis of Proposed Changes to the Regulatory Text

In addition to updating existing standards incorporated by reference, adding new standards, and removing obsolete standards, we propose to modify technical regulatory text in the following sections of Subchapter F. For the convenience of the reader, the list below excludes purely stylistic revisions and corrections of drafting errors.

Part 50—General Provisions

Section 50.05-5 Existing Boilers, Pressure Vessels or Piping Systems

Modifying paragraph (b) to eliminate redundant text and more clearly describe the requirements for recalculating the maximum allowable working pressure.

Section 50.05-20 Steam-Propelled Motor Boats

Replacing the words “motor boats” with the more current and universally used “vessels”.

Section 50.10-23 Marine Safety Center

Modifying the contact information for the MSC and the details for electronically submitting documents

ate redundant text and more clearly describe the requirements for recalculating the maximum allowable working pressure.

Section 50.05-20 Steam-Propelled Motor Boats

Replacing the words “motor boats” with the more current and universally used “vessels”.

Section 50.10-23 Marine Safety Center

Modifying the contact information for the MSC and the details for electronically submitting documents.

Section 50.20-5 Procedures for Submittal of Plans

Modifying the procedures for submitting plans to the Coast Guard by eliminating the requirements in paragraph (b) for plans to be submitted in triplicate, since most plans are electronically submitted, and by deleting unnecessary detail in paragraph (c).

Section 50.20-10 Number of Copies of Plans Required

Deleting this section. Submittal of plans is adequately addressed in § 50.20-5.

Section 50.20-15 Previously Approved Plans

Deleting the unnecessary text “(including work accomplished under a different contract)” in paragraph (a).

Section 50.20-30 Alternative Materials or Methods of Construction

Modifying paragraph (a) to include the word “materials” and deleting paragraph (b). These changes improve the clarity of the section.

Section 50.25-1 General

Deleting paragraph (e) as unnecessary because nonmetallic flexible hoses, including those intended for hydraulic service, are adequately addressed in § 56.60-25.

Section 50.25-7 Testing of Products Required To Be Certified in Presence of Marine Inspector

Deleting paragraphs (c) and (d) as unnecessary. When specific testing conditions are required, they are specified in the applicable standards or regulations.

Part 52—Power Boilers

Replacing the words “boiler pressure vessel code” with “BPVC” throughout all of part 52, as BPVC is recognized as the appropriate acronym for the ASME Boiler Pressure Vessel Code.

Section 52.01-52.25 Power Boilers

Modifying various paragraphs to delete text already addressed in ASME BPVC

ions are required, they are specified in the applicable standards or regulations.

Part 52—Power Boilers

Replacing the words “boiler pressure vessel code” with “BPVC” throughout all of part 52, as BPVC is recognized as the appropriate acronym for the ASME Boiler Pressure Vessel Code.

Section 52.01-52.25 Power Boilers

Modifying various paragraphs to delete text already addressed in ASME BPVC.

Section 52.01-3 Definitions

Deleting definitions listed in this section but not currently used in Part 52 and not needed going forward, as there is no need to define a term if it is not used later in the regulatory text. Deleted terms include: High temperature water boiler, packaged boiler, Fired steam boiler, Hybrid boiler, Shell, Heads, Dished heads, Stayed heads, Water wall, Header, Domes, Steam chimneys, Corrugated furnace, Plain furnace, Combustion chamber, Separate combustion chamber, Common combustion chamber, Crown or top plate, Curved bottom plate, Combustion chamber tube sheet, Combustion chamber back sheet, Seamless tube, Electric resistance welded tube, Stay tube, Tube sheet, Ligament, Longitudinal ligament, Circumferential ligament, Diagonal ligament, Stays and supports, Solid screw staybolt, Welded collar, Hollow screw staybolt, Flexible staybolt, Sling stay, Crowfoot, Crowfoot stay, Diagonal stay, Gusset stay, Dog stay, Girder, Structural stiffeners, Reinforcement, Pressure loaded pilot actuated safety valve, Spring loaded pilot actuated safety valve, Spring loaded pilot valve, Relief valve, Safety relief valve, Conventional safety relief valve, Balanced safety relief valve, Internal spring safety relief valve, Power actuated relief valve, Breaking pin device, Shear pin device, Frangible disk device, Bursting disk device, Feed valve, Salinometer cocks, Expanding, Beading, Bell mouthing, Telltale hole, Openings, Pressure, Absolute pressure, Internal pressure, and External pressure. And, deleting Figure 52.01-3—Acceptable Types of Boiler Stays

anced safety relief valve, Internal spring safety relief valve, Power actuated relief valve, Breaking pin device, Shear pin device, Frangible disk device, Bursting disk device, Feed valve, Salinometer cocks, Expanding, Beading, Bell mouthing, Telltale hole, Openings, Pressure, Absolute pressure, Internal pressure, and External pressure. And, deleting Figure 52.01-3—Acceptable Types of Boiler Stays. Figure 52.01-3 is not necessary, as the ASME BPVC

Section 52.01-50 Fusible Plugs (Modifies A-19 Through A-21)