Airworthiness Directives; Boeing Model 737-100 and -200 Series Airplanes

Federal RegisterMar 14, 1997

Ask Donna

What actually matters in this document.

Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 96-NM-152-AD]

RIN 2120-AA64

Airworthiness Directives; Boeing Model 737-100 and -200 Series

Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Supplemental notice of proposed rulemaking; reopening of

comment period.

-----------------------------------------------------------------------

SUMMARY: This document revises an earlier proposed airworthiness

directive (AD), applicable to all Boeing Model 737-100 and -200 series

airplanes, that would have required replacement of certain outboard and

inboard wheel halves with improved wheel halves. That action also would

have required cleaning and inspecting certain outboard and inboard

wheel halves for corrosion, missing paint in large areas, and cracks;

and repair or replacement of the wheel halves with serviceable wheel

halves, if necessary. That proposal was prompted by a review of the

design of the flight control systems on Model 737 series airplanes.

This action revises the proposed rule by extending the compliance time,

revising the applicability of the AD, and clarifying part and serial

numbers of affected wheel assemblies and halves. The actions specified

by this proposed AD are intended to prevent failure of the wheel

flanges, which could result in damage to the hydraulics systems, jammed

flight controls, loss of electrical power, or other combinations of

failures; and consequent reduced controllability of the airplane.

DATES: Comments must be received by April 3, 1997.

ADDRESSES: Submit comments in triplicate to the Federal Aviation

Administration (FAA), Transport Airplane Directorate, ANM-103,

Attention: Rules Docket No. 96-NM-152-AD, 1601 Lind Avenue, SW.,

Renton, Washington 98055-4056. Comments may be inspected at this

location between 9:00 a.m. and 3:00 p.m., Monday through Friday, except

Federal holidays.

The service information referenced in the proposed rule may be

obtained from Allied Signal Aerospace Company, Bendix Wheels and Brakes

Division, South Bend, Indiana 46624; and Bendix, Aircraft Brake and

Strut Division, 3520 West Mestmoor Street, South Bend, Indiana 46624.

This information may be examined at the FAA, Transport Airplane

Directorate, 1601 Lind Avenue, SW., Renton, Washington.

FOR FURTHER INFORMATION CONTACT: David Herron, Aerospace Engineer,

Systems and Equipment Branch, ANM-130S, FAA, Seattle Aircraft

Certification Office, 1601 Lind Avenue, SW., Renton, Washington;

telephone (206) 227-2672; fax (206) 227-1181.

SUPPLEMENTARY INFORMATION:

Comments Invited

Interested persons are invited to participate in the making of the

proposed rule by submitting such written data, views, or arguments as

they may desire. Communications shall identify the Rules Docket number

and be submitted in triplicate to the address specified above. All

communications received on or before the closing date for comments,

specified above, will be considered before taking action on the

proposed rule.

The proposals contained in this notice may be changed in light of

the comments received.

Comments are specifically invited on the overall regulatory,

economic, environmental, and energy aspects of the proposed rule. All

comments submitted will be available, both before and after the closing

date for comments, in the Rules Docket for examination by interested

persons. A report summarizing each FAA-public contact concerned with

the substance of this proposal will be filed in the Rules Docket.

Commenters wishing the FAA to acknowledge receipt of their comments

submitted in response to this notice must submit a self-addressed,

stamped postcard on which the following statement is made: ``Comments

to Docket Number 96-NM-152-AD.'' The postcard will be date stamped and

returned to the commenter.

[[Page 12124]]

Availability of NPRMs

Any person may obtain a copy of this NPRM by submitting a request

to the FAA, Transport Airplane Directorate, ANM-103, Attention: Rules

Docket No. 96-NM-152-AD, 1601 Lind Avenue, SW., Renton, Washington

98055-4056.

Discussion

A proposal to amend part 39 of the Federal Aviation Regulations (14

CFR part 39) to add an airworthiness directive (AD), applicable to all

Boeing Model 737-100 and -200 series airplanes, was published as a

notice of proposed rulemaking (NPRM) in the Federal Register on August

28, 1996 (61 FR 44245). That NPRM would have required replacement of

certain outboard and inboard wheel halves with improved wheel halves.

That NPRM also would have required cleaning and inspecting certain

outboard and inboard wheel halves for corrosion, missing paint in large

areas, and cracks; and repair or replacement of the wheel halves with

serviceable wheel halves, if necessary. That NPRM was prompted by a

review of the design of the flight control systems on Model 737 series

airplanes. The actions specified by that NPRM are intended to prevent

damage to the wheel flanges, which could result in failure of the

hydraulics systems, jammed flight controls, loss of electrical power,

or other combinations of failures; and consequent reduced

controllability of the airplane.

Actions Since Issuance of Previous Proposal

Due consideration has been given to the comments received in

response to the NPRM.

Support for the Proposal

Two commenters support the proposed rule.

Requests to Reopen Comment Period

Several commenters request that the proposal be reissued and the

public comment period reopened. The commenters ask that the intent of

the proposal be clarified. The commenters state that the proposal

appears to require that an inspection and a replacement be accomplished

concurrently within 180 days. Allied Signal indicates that it is

unclear why operators should be required to replace wheel halves and

then inspect those wheel halves that were just removed.

In its justification for the request to reopen the comment period,

another commenter states that the issue addressed in the proposed AD

arises from a failure that occurred on a military aircraft. The

commenter indicates that, when maintained properly and operated on

civilian airliners, certain wheel halves are not subject to the

questionable maintenance practices and adverse operational conditions

often associated with military hardware. The commenter adds that, in

particular, the inspections required at tire replacement occur far more

frequently due to utilization differences. The commenter believes that

strengthened inspection requirements in accordance with the latest

manufacturer's recommendations can provide for safe operation of the

older wheels until replacements would normally be available.

The FAA concurs with the commenters' requests to reopen the comment

period for this proposed rule and to provide clarification of the

intent of the proposal. The intent of this proposed AD is that the

affected fleet be equipped eventually with more resilient wheel halves

that provide greater tolerance for corrosion and handling damage. Some

failures of wheel halves have occurred because indications of corrosion

or handling damage were not detected in a timely manner. Therefore, the

FAA included a requirement in the original NPRM indicating that, until

the time that the existing wheel halves can be replaced with the more

resilient wheel halves, repetitive cleaning and inspections of the

wheel halves must be performed in accordance with the cleaning/

inspection method described in Allied Signal Service Bulletin No. 737-

32-026. Accomplishment of these repetitive actions will ensure that an

acceptable level of safety is maintained until the wheel halves are

replaced.

The FAA has revised this supplemental NPRM to clarify these issues:

The repetitive inspection requirement, which appeared as

paragraph (b) of the original NPRM, is contained in paragraph (a) of

this supplemental NPRM. Paragraph (a) of this supplemental NPRM has

been revised to clarify that the inspections of the wheel halves must

be repeated until the wheel halves are replaced.

The replacement requirement, which appeared in paragraph

(a) of the original NPRM, is contained in paragraph (b) of this

supplemental NPRM. Paragraph (b) of this supplemental NPRM has been

revised to clarify that accomplishment of the replacement terminates

the repetitive inspections required by paragraph (a).

Request for Extended Compliance Time

Three commenters express concern that replacement of certain

outboard and inboard wheel halves with improved halves cannot be

supported within the proposed compliance time of 180 days. One of these

commenters, Allied Signal, suggests that the compliance time be

extended to 365 days, and that paragraph (c) of the original NPRM be

deleted. Allied Signal indicates that the lead time necessary to order

and receive forgings, machine, finish, and ship replacement wheels

involves approximately 120 days, which is a significant portion of the

proposed 180-day compliance time. Allied Signal states that it does not

have sufficient information to determine how many wheels need

replacement, and may not have this information until a final rule is

effective and orders for replacements arrive.

In light of these requests, the FAA has reconsidered the compliance

times proposed in the original NPRM. The FAA considers that the

compliance time of 180 days (and thereafter at each tire change) for

inspections of the wheel halves, as proposed in paragraph (b) of the

original NPRM, is appropriate. The FAA considers that these repetitive

inspections must be accomplished at the originally proposed intervals

in order to provide an acceptable level of safety until the replacement

can be accomplished.

However, in consideration of parts availability, the FAA has

determined that the compliance time for replacement of the wheel halves

can be extended from 180 days to two years without compromising safety,

and that paragraph (c) of the original NPRM can be removed from this

supplemental NPRM. Given this revised compliance time for

accomplishment of the replacement, the FAA estimates that approximately

four tire changes would be accomplished in the two-year period prior to

the time the replacement would be required. The compliance time

specified in paragraph (b) of this supplemental NPRM has been revised

accordingly. In addition, paragraph (c) of the original NPRM has been

removed from this supplemental NPRM.

Requests for Clarification of Part Numbering System

Two commenters request clarification of the part numbering system

specified in the proposal. Further, Allied Signal recommends that

serial number H-1049 be used in all places where serial number H-999

appeared in the NPRM to avoid numerical discrepancies and to ensure

adequate coverage of these wheel halves. Allied Signal submits two sets

of suggested changes to the NPRM: one set based on an intent to remove

all affected wheels from service, and the other set based on an intent

to inspect all affected

[[Page 12125]]

wheels and remove from service only those with cracks.

Allied Signal states that a misunderstanding exists with regard to

the serial numbering system used by Aircraft Landing Systems (formerly

Bendix). Allied Signal clarifies that wheels having a ``B'' prefix

serial number are original equipment wheels shipped from the factory.

Individual inboard and individual outboard wheel halves are given the

same ``B'' serial number on the final production line and mated

together to form a complete wheel assembly. Wheel halves having serial

numbers with an ``H'' prefix are replacement service halves.

Availability of a service wheel half allows an operator to replace a

damaged wheel half instead of the entire wheel assembly. Individual

inboard and outboard service halves are not mated together to form a

complete assembly; they are shipped independently of each other.

Allied Signal also clarifies that Bendix Service Information Letter

(SIL) 392, Revision 1, dated November 15, 1979, and Allied Signal

Service Bulletin No. 737-32-026, dated April 26, 1988, apply to both

the ``H'' and ``B'' prefix serial numbers, not just the ``H'' prefix

serial numbers used in the ``B'' prefix wheel assemblies.

The FAA agrees that clarification of the part and serial numbers

specified in the original NPRM is necessary. As stated previously, the

FAA intends that all affected wheels be removed from service; the FAA

concurs with the changes suggested by Allied Signal based on that

intent. Paragraphs (a) and (b) of this supplemental NPRM reflect the

appropriate part and serial numbers provided by Allied Signal. In

addition, serial number H-1049 has been specified in this supplemental

NPRM in place of serial number H-999.

Request to Revise the Applicability of the Proposed AD

The Air Transport Association (ATA) of America, on behalf of one of

its members, requests that the applicability of the proposed AD be

limited only to the Bendix main wheel assemblies that prompted the

airworthiness concern. The ATA states that the proposed applicability

affects even operators with BFGoodrich brakes. The commenter concludes

that, unless operators of airplanes equipped with BFGoodrich brakes

submit a request for and receive approval of an alternative method of

compliance (AMOC), those operators are considered in noncompliance with

the AD.

The FAA concurs with the commenter's request to revise the

applicability of the original NPRM. This FAA has revised the

applicability of this supplemental NPRM to specify that the proposed

rule applies only to Boeing Model 737-100 and -200 series airplanes

equipped with Bendix main wheel assemblies having part number 2601571-

1. Paragraphs (a) and (b) of the supplemental NPRM specify the serial

numbers of the inboard and outboard wheel halves that are affected.

The FAA also clarifies that operators of airplanes equipped with

BFGoodrich brakes would not be required to submit a request for

approval of an AMOC. Although the applicability of the original NPRM

identified the affected airplanes as ``all Model 737-100 and -200

series airplanes,'' paragraphs (a) and (b) specified clearly that only

those airplanes equipped with Bendix main wheel assemblies having

certain part and serial numbers are affected by the proposed rule.

Therefore, operators of airplanes equipped with other main wheel

assemblies are not subject to the requirements of this AD, and would

have no reason to apply for approval of an AMOC.

Request to Revise Statement of Findings of Critical Design Review

Team

One commenter requests the second paragraph of the Discussion

section that appeared in the preamble to the proposed rule be revised

to accurately reflect the findings of the Critical Design Review (CDR)

team. The commenter asks that the FAA delete the one sentence in that

paragraph, which read: ``The recommendations of the team include

various changes to the design of the flight control systems of these

airplanes, as well as correction of certain design deficiencies.'' The

commenter suggests that the following sentences should be added: ``The

team did not find any design issues that could lead to a definite cause

of the accidents that gave rise to this effort. The recommendations of

the team include various changes to the design of the flight control

systems of these airplanes, as well as incorporation of certain design

improvements in order to enhance its already acceptable level of

safety.''

The FAA acknowledges that the CDR team did not find any design

issue that could lead to a definite cause of the accidents that gave

rise to this effort. However, as a result of having conducted the CDR

of the flight control systems on Boeing Model 737 series airplanes, the

team indicated that there are a number of recommendations that should

be addressed by the FAA for each of the various models of the Model

737. In reviewing these recommendations, the FAA has concluded that

they address unsafe conditions that must be corrected through the

issuance of AD's. Therefore, the FAA does not concur that these design

changes merely ``enhance [the Model 737's] already acceptable level of

safety.''

Conclusion

Since these changes provide significant clarification of the intent

and requirements of the originally proposed rule, the FAA has

determined that it is in the public interest to reopen the comment

period to provide additional opportunity for public comment.

Cost Impact

There are approximately 634 Boeing Model 737-100 and -200 series

airplanes of the affected design in the worldwide fleet. The FAA

estimates that 241 airplanes of U.S. registry would be affected by this

proposed AD.

The FAA estimates that it would take approximately 4 work hours per

airplane to accomplish the proposed replacement of wheel halves, and

that the average labor rate is $60 per work hour. Required parts would

cost approximately $20,212 per airplane. Based on these figures, the

cost impact of the proposed replacement on U.S. operators is estimated

to be $4,928,932, or $20,452 per airplane.

The FAA also estimates that it would take approximately 2 work

hours per airplane to accomplish the proposed cleaning and inspection,

and that the average labor rate is $60 per work hour. Based on these

figures, the cost impact of the proposed cleaning and inspection on

U.S. operators is estimated to be $28,920, or $120 per airplane.

The cost impact figures discussed above are based on assumptions

that no operator has yet accomplished any of the proposed requirements

of this AD action, and that no operator would accomplish those actions

in the future if this AD were not adopted.

Regulatory Impact

The regulations proposed herein would not have substantial direct

effects on the States, on the relationship between the national

government and the States, or on the distribution of power and

responsibilities among the various levels of government. Therefore, in

accordance with Executive Order 12612, it is determined that this

proposal would not have sufficient federalism implications to warrant

the preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this proposed

regulation: (1) Is not a ``significant regulatory action''

[[Page 12126]]

under Executive Order 12866; (2) is not a ``significant rule'' under

the DOT Regulatory Policies and Procedures (44 FR 11034, February 26,

1979); and (3) if promulgated, will not have a significant economic

impact, positive or negative, on a substantial number of small entities

under the criteria of the Regulatory Flexibility Act. A copy of the

draft regulatory evaluation prepared for this action is contained in

the Rules Docket. A copy of it may be obtained by contacting the Rules

Docket at the location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, pursuant to the authority delegated to me by the

Administrator, the Federal Aviation Administration proposes to amend

part 39 of the Federal Aviation Regulations (14 CFR part 39) as

follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new

airworthiness directive:

BOEING: Docket 96-NM-152-AD.

Applicability: Boeing Model 737-100 and -200 series airplanes

equipped with Bendix main wheel assemblies having part number

2601571-1, certificated in any category.

Note 1: This AD applies to each airplane identified in the

preceding applicability provision, regardless of whether it has been

otherwise modified, altered, or repaired in the area subject to the

requirements of this AD. For airplanes that have been modified,

altered, or repaired so that the performance of the requirements of

this AD is affected, the owner/operator must request approval for an

alternative method of compliance in accordance with paragraph (c) of

this AD. The request should include an assessment of the effect of

the modification, alteration, or repair on the unsafe condition

addressed by this AD; and, if the unsafe condition has not been

eliminated, the request should include specific proposed actions to

address it.

Compliance: Required as indicated, unless accomplished

previously.

To prevent failure of the wheel flanges, which could result in

damage to the hydraulics systems, jammed flight controls, loss of

electrical power, or other combinations of failures; and consequent

reduced controllability of the airplane, accomplish the following:

(a) For airplanes equipped with a Bendix main wheel assembly

having part number (P/N) 2601571-1 with an inboard wheel half with

serial number (S/N) B-5999 or lower, or S/N H-1799 or lower; or with

an outboard wheel half with S/N B-5999 or lower, or S/N H-1049 or

lower; accomplish the following:

(1) Within 180 days after the effective date of this AD, and

thereafter at each tire change until the replacement required by

paragraph (b) of this AD is accomplished:

Accomplish the actions specified in paragraphs (a)(1)(i),

(a)(1)(ii), and (a)(1)(iii) of this AD, in accordance with the

Accomplishment Instructions of Allied Signal Service Bulletin No.

737-32-026, dated April 26, 1988, including Attachments 1 and 2.

(i) Clean any inboard and outboard wheel half specified in

paragraph (a) of this AD. And

(ii) Inspect the wheel halves for corrosion or missing paint. If

any corrosion is found, or if any paint is missing in large areas,

prior to further flight, strip or remove paint, and remove any

corrosion. And

(iii) Perform an eddy current inspection to detect cracks of the

bead seat area.

(2) If any cracking is found during the inspections required by

this paragraph, prior to further flight, repair or replace the wheel

halves with serviceable wheel halves in accordance with procedures

specified in the Component Maintenance Manual.

(b) For airplanes equipped with a Bendix main wheel assembly

having P/N 2601571-1 with an inboard wheel half with S/N B-5999 or

lower, or S/N H-1799 or lower; or with an outboard wheel half with

S/N B-5999 or lower, or S/N H-1049 or lower; accomplish the

following: Within 2 years after the effective date of this AD,

accomplish the actions specified in paragraphs (b)(1) and (b)(2) of

this AD, in accordance with Bendix Service Information Letter (SIL)

392, Revision 1, dated November 15, 1979. Accomplishment of the

replacement constitutes terminating action for the repetitive

inspections required by paragraph (a) of this AD.

(1) Remove any inboard wheel half specified in paragraph (b) of

this AD, and replace it with an inboard wheel half having P/N

2607046, S/N B-6000 or greater, or S/N H-1800 or greater. And

(2) Remove any outboard wheel half specified in paragraph (b) of

this AD, and replace it with an outboard wheel half having P/N

2607047, S/N B-6000 or greater, or S/N H-1050 or greater.

(c) An alternative method of compliance or adjustment of the

compliance time that provides an acceptable level of safety may be

used if approved by the Manager, Seattle Aircraft Certification

Office (ACO), FAA, Transport Airplane Directorate. Operators shall

submit their requests through an appropriate FAA Principal

Maintenance Inspector, who may add comments and then send it to the

Manager, Seattle ACO.

Note 2: Information concerning the existence of approved

alternative methods of compliance with this AD, if any, may be

obtained from the Seattle ACO.

(d) Special flight permits may be issued in accordance with

sections 21.197 and 21.199 of the Federal Aviation Regulations (14

CFR 21.197 and 21.199) to operate the airplane to a location where

the requirements of this AD can be accomplished. Issued in Renton,

Washington, on March 7, 1997.

Darrell M. Pederson,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

[FR Doc. 97-6438 Filed 3-13-97; 8:45 am]

BILLING CODE 4910-13-U

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.