Miscellaneous Minor and Technical Amendments

SUMMARY: The Occupational Safety and Health Administration (OSHA) has

initiated a comprehensive line-by-line review of its standards

published in the Code of Federal Regulations (CFR) as directed by

President Clinton in March 1995. From this review, OSHA has identified

a number of sections and provisions of these standards for correction

and technical amendment. In this document, OSHA is making corrections,

deleting redundant provisions, and clarifying and reorganizing various

other provisions throughout OSHA's standards in the CFR. This document

does not change the substantive requirements of the standards.

EFFECTIVE DATE: May 6, 1996. The incorporations by reference of the

consensus standards listed in Secs. 1926.1002, 1926.1003, and 1928.51

are approved by the Director of the Federal Register as of May 6, 1996.

FOR FURTHER INFORMATION CONTACT: Ms. Anne Cyr, Office of Information

and Consumer Affairs, OSHA, U.S. Department of Labor, Room N-3647, 200

Constitution Avenue, N.W., Washington, D.C. 20210; telephone: (202)

219-8615.

SUPPLEMENTARY INFORMATION:

I. Background

In March 1995, the President directed Federal agencies to undertake

a line-by-line review of their regulations to determine where they

could be simplified or clarified. OSHA initiated such a review, and as

a result completed a document on May 31, 1995, entitled ``OSHA's

Regulatory Reform Initiatives.'' That document detailed the Agency's

findings as to which regulations could be deleted or revised to improve

compliance by employers and, consequently, provide enhanced

occupational safety and health protection to employees. This regulatory

improvement process involves revocation of outdated and obsolete

provisions, consolidation of repetitious provisions, and clarification

of confusing language.

The Agency is beginning this process with this document, by

addressing minor clarifications, corrections, and technical amendments

to OSHA standards. These do not require notice and comment. A detailed

discussion of these actions is provided below under ``Summary and

Explanation.'' In addition, the Agency plans to undertake several more

regulatory reform initiatives. OSHA is developing a proposal to make

substantive changes in various standards to diminish regulatory burdens

without reducing worker protections. OSHA also intends to take actions

to reduce paperwork and shorten and simplify its standards that are

codified in the CFR.

II. Summary and Explanation

A. Merging the 13 Carcinogen Standards Into Single Standards in 29 CFR

Parts 1910, 1915, and 1926

Thirteen similar standards for carcinogenic chemicals are codified

in subpart Z of OSHA's General Industry standards at 29 CFR 1910.1003

through 1016. The regulatory requirements for each are similar, with

the few differences based principally on the corrosiveness of the

substance, or its physical state at room temperature. Because of their

similarities, OSHA has decided to combine the 13 standards into a

single rule. Accordingly, OSHA is issuing a technical amendment

combining the 13 carcinogenic chemical standards into a single

consolidated standard at Sec. 1910.1003, entitled ``13 Carcinogens.''

No substantive revisions have been made to any provisions of the 13

carcinogenic chemical standards. Where requirements vary for different

chemicals, paragraphs are being added to Sec. 1910.1003 to include

these differing requirements.

The standards for the 13 carcinogenic chemicals found under 29 CFR

Parts 1915 and 1926 are being consolidated in the same manner. They

will be consolidated under single standards for each of these parts,

Secs. 1915.1003 and 1926.1103, titled ``13 Carcinogens.''

B. Consensus Standards and Organizations and Incorporation by Reference

Statements in 29 CFR Part 1910

Among the provisions being removed from the CFR are the following

12 General Industry sections that list the addresses of consensus

organizations: 29 CFR 1910.40, 1910.70, 1910.100, 1910.116, 1910.140,

1910.148, 1910.171, 1910.190, 1910.222, 1910.247, 1910.257, and

1910.275. These addresses are being consolidated into Sec. 1910.6,

titled ``Incorporation by Reference.'' The addresses have been updated

and may be used to obtain copies of the original consensus standards

that were incorporated into these sections. Consistent with this

revision, Sec. 1910.6 is being amended to include a list of the

consensus standards incorporated by reference into the CFR, as well as

references to the OSHA-related CFR sections developed from each of

these incorporated consensus standards.

Copies of the original consensus standards are also available from

OSHA area offices.

The following 14 sections of 29 CFR part 1910 contain only

identifying information regarding the consensus standards which were

originally used as sources for OSHA standards: 29 CFR 1910.31, 1910.39,

1910.69, 1910.99, 1910.115, 1910.139, 1910.150, 1910.153, 1910.170,

1910.189, 1910.221, 1910.246, 1910.256, and 1910.274. Because OSHA has

revised and updated many of its standards over the past 25 years, the

references to the original sources for these standards are no longer

valid. Accordingly, OSHA is deleting these references. The

parenthetical note entitled ``Source'' at the bottom of

Sec. 1910.68(e)(3) is being removed as well.

In this document, OSHA is also consolidating all ``incorporation by

reference'' (IBR) statements into Sec. 1910.6. These statements are

currently scattered throughout part 1910. The paragraphs affected by

this change are: Sec. 1910.133(b) (1) and (2), 1910.135(b) (1) and (2),

1910.136(b) (1) and (2), and Sec. 1910.266 (d)(3)(iv), (e)(2)(i),

(f)(3) (ii) through (iv), (f)(4), and (f)(5)(i).

C. Effective Dates Codified Under 29 CFR Part 1910

Several OSHA standards published in the CFR provide information

regarding the date the standard was to become effective. In general,

effective dates are not included or retained as part of the CFR. In

addition, the effective dates published in the CFR under these

provisions have expired. OSHA therefore is revising or deleting the

effective date provisions of the following standards, as appropriate:

Secs. 1910.17, 1910.66, 1910.114, 1910.145, 1910.157, 1910.158,

1910.182, 1910.216, 1910.217, 1910.261, 1910.265, and 1910.272.

D. Editorial Corrections to 29 CFR part 1910

The following miscellaneous editorial corrections are being made to

29 CFR part 1910:

1. Because internal units within a CFR section are to be referred

to as

[[Page 9229]]

``paragraphs,'' the phrase ``subdivision (A) of this subdivision'' in

Sec. 1910.68(c)(7)(ii)(B) is being revised to read ``paragraph

(c)(7)(ii)(A) of this section,'' while the phrase ``subparagraph

(6)(ii) of this paragraph'' in Sec. 1910.94(c)(4)(iii) is being changed

to read ``paragraph (c)(6)(ii) of this section.''

2. In the first sentence of Sec. 1910.20(c)(13)(i), the word

``least'' is being changed to ``latest.''

3. In Sec. 1910.94, the term ``[Reserved]'' at the beginning of

paragraph (c)(5)(iii) is being removed, and the succeeding designation

letter ``(A)'' is being moved immediately to the right of the ``(iii)''

at the beginning of the paragraph.

4. The table titled ``OSHA Onsite Consultation Project Directory''

in Appendix G to Sec. 1910.95 is being deleted. Since this table was

first published, numerous revisions have occurred to the entries cited

in the directory, making the information in this table obsolete.

5. In two places (Appendix H to Sec. 1910.95 and Appendix D to

subpart L of 29 CFR part 1910), an out-of-date telephone number for

OSHA's Technical Data Center, ``523-9700,'' is being changed to the

current number, ``219-7500.''

6. In Sec. 1910.120, the comma that runs into the beginning of the

word ``uncontrolled'' near the middle of paragraph (a)(1)(i) is being

removed to improve clarity.

7. In paragraphs (d)(2), (d)(4), and (d)(6) of Sec. 1910.145, the

paragraph designation ``(i)'' is being removed because these paragraphs

have no subsequent designations.

8. In the listing for OSHA's Publications Office under Appendix B

to Sec. 1910.177, an out-of-date telephone number, ``523-9667,'' is

being changed to the current number ``219-4667.''

9. In table O-10 following Sec. 1910.217(f)(4), the fourth entry in

the first column that reads ``1\1/2\ to 5\1/2\'' is being changed to

read ``3\1/2\ to 5\1/2\.''

10. In Sec. 1910.217(g), the title ``Director of the Office of

Standards Development'' is being changed to read ``Director of the

Directorate of Safety Standards Programs.''

11. In Sec. 1910.440, the phrase ``Health, Education and Welfare''

in paragraphs (b)(1) and (b)(5)(ii) is being revised to read ``Health

and Human Services.''

E. Revisions to 29 CFR Part 1926 Standards Incorporated From 29 CFR

Part 1910

Minor corrections and technical amendments also are being made to

several 29 CFR part 1926 (Construction Industry) standards that were

incorporated from 29 CFR part 1910 (General Industry) in a previous

rulemaking notice (June 30, 1993, 58 FR 35076). This previous action

made no substantive changes to the incorporated standards, but the

publication of these standards introduced various typographical errors

and omissions. In addition, some changes were made to properly reflect

the legal history and their adoption under the relevant statutes.

F. Miscellaneous Technical Amendments to 29 CFR Part 1926

On April 20, 1982 (47 FR 16986), OSHA published a final rule that

consolidated standards addressing ship repair, shipbuilding, and

shipbreaking, located under 29 CFR parts 1915 through 1917, into 29 CFR

part 1915 (``Shipyard employment''). Paragraph (b) of Sec. 1926.30

(``Shipbuilding and ship repairing''), however, still refers to old

parts 1916 and 1917. These references are being corrected.

Several changes are being made to Sec. 1926.31 to provide current

addresses and cross-references.

G. Revisions to Standards Addressing Roll-Over Protection Structures

for Tractors Under 29 CFR Parts 1926 and 1928

Various provisions of OSHA standards that specify minimum test

procedures and performance requirements for manufacturers who design

and construct roll-over protective structures (ROPS) and overhead

protection attached to tractors used in construction work and

agricultural operations are being removed. OSHA is removing these

detailed specifications from the CFR because they are design criteria

generally not useful to employers. The Agency is replacing them with

references to the source consensus standards from which they were

developed. The references will be provided in footnotes to the relevant

provisions of the OSHA standards. The substantive requirements are

unchanged.

This rulemaking involves the following amendments:

1. Paragraphs (c) through (i), and (k) of Sec. 1926.1002 are

deleted and replaced with a reference to Society of Automotive

Engineers (SAE) consensus standard J334a in paragraph (a)(1) of

Sec. 1926.1002.

2. Paragraphs (c) through (g) of Sec. 1926.1003 are deleted and

replaced with a reference to SAE J167 in paragraph (a)(1) of

Sec. 1926.1003.

3. Sections 1928.52 and 1928.53 and Appendix B to subpart C of 29

CFR part 1928 are deleted and replaced by references to SAE J168 and

J334 and American Society of Agricultural Engineers consensus standards

306.3 and 336.1 in paragraph (b)(1) of Sec. 1928.51.

H. Revisions to the Cadmium Standard Under 29 CFR Part 1928

The cadmium standard for the Agriculture Industry, Sec. 1928.1027,

duplicates the cadmium standard of 29 CFR part 1910. The Agency has

determined that publishing the full text of the standard under part

1928 is unnecessary because the requirements of the standard can be

found in the General Industry cadmium standard (Sec. 1910.1027). A

cross-reference from the agriculture industry standards to

Sec. 1910.1027 is being inserted in place of the full text of the

standard. OSHA also is adding paragraph (a)(6) to Sec. 1928.21

specifying that the cadmium standard under part 1910 is applicable to

the agriculture industry.

I. Agreements With and Grants to States

The primary purpose of 29 CFR part 1901 has been to interpret and

apply section 18(h) of the Occupational Safety and Health Act of 1970

(the Act). Since the State agreements that were permitted under section

18(h) have been obsolete since 1972, most of part 1901 is no longer

necessary. Therefore OSHA is revoking all of part 1901, with the

exception of the first sentence of Sec. 1901.2. That sentence

interprets the preemption language in section 18(a) of the Act and is

relied on by courts in preemption cases. That language is being moved

to become the fourth sentence in paragraph (a) of 29 CFR 1902.1.

Part 1950 of title 29 CFR interprets and applies section 23 (a) and

(b) of the Act, which authorizes the Secretary of Labor to make grants

to the States for certain development and planning purposes with regard

to occupational safety and health State plans. As the statutory

authority for making these grants to the States expired in 1973, it is

being revoked.

Part 1951 of title 29 CFR contains procedures for making grants to

the States to assist them in administering and enforcing programs for

occupational safety and health contained in State plans. Since

financial grant rules and regulations can be found in 29 CFR part 97

and in Office of Management and Budget Circular A-102, part 1951 is

redundant and is being revoked.

III. Exemption From Notice and Comment Procedures

OSHA has determined that this rulemaking is not subject to the

[[Page 9230]]

procedures for public notice-and-comment rulemaking specified under

section 4 of the Administrative Procedure Act (5 U.S.C. 553) or sec.

6(b) of the Occupational Safety and Health Act of 1970 (29 U.S.C.

655(b)) because this rulemaking does not affect the substantive

requirements or coverage of the standards involved. This rulemaking

does not modify or revoke existing rights and obligations, and new

rights and obligations have not been established. Under this

rulemaking, the Agency is merely correcting or clarifying existing

regulatory requirements. OSHA therefore finds that public notice-and-

comment procedures are unnecessary within the meaning of 5 U.S.C.

553(b)(3)(B) and 29 CFR 1911.5.

IV. Clearance of Information Collection Requirement

On August 29, 1995, the Office of Management and Budget (OMB)

published a new 5 CFR part 1320 (60 FR 44978), implementing the

information collection provisions of the Paperwork Reduction Act of

1995 (PRA 95) (Pub. L. 104-13, May 22, 1995). Part 1320, which became

effective on October 1, 1995, sets forth procedures for information

collection requirements. The Act changed the previous law in several

significant ways. Among other things, it redefined ``collection of

information'' to include third-party and public disclosures.

To be in compliance with PRA 95 by October 1995, the Department of

Labor published a document in the Federal Register seeking generic

clearances from OMB for a number of existing information collection

requests (60 FR 35228, July 6, 1995). This was necessary as third-party

disclosure paperwork burden hours were previously deleted from the

Information Collection Requests as adjustments resulting from the Dole,

Secretary of Labor et al. v. United Steelworkers of America, Opinion of

the Court 494 U.S. 26, 33 (1990) decision. The 13 carcinogen standards'

information collection requests were part of this overall generic

clearance.

On September 19, 1995, OMB approved the information collection

requirements contained in the 13 carcinogen standards until August 31,

1996. Each of the 13 carcinogen standards currently set out the OMB

approval number at the end of the corresponding CFR section. While this

final rule combines the 13 carcinogens under a single CFR section

(which appears in OSHA's standards as Secs. 1910.1003, 1915.1003, and

1926.1103), it does not affect or change the burden of those

requirements. The OMB numbers for the 13 carcinogens standards are

unchanged, and being are listed as a group at the end of the combined

carcinogens section.

The 13 separate information collection requests will be combined

into one information collection request when submitting the package to

OMB for approval later this year. This package will be submitted under

OMB number 1218-0085.

List of Subjects

29 CFR Part 1901

Intergovernmental relations, Occupational safety and health.

29 CFR Part 1902

Occupational safety and health, State and local government.

29 CFR Part 1910

Hazardous materials, Incorporation by reference, Occupational

safety and health.

29 CFR Part 1915

Shipyards, Occupational safety and health, Protective equipment.

29 CFR Part 1926

Construction industry, Hazardous materials, Incorporation by

reference, Occupational safety and health.

29 CFR Part 1928

Agriculture, Incorporation by reference, Occupational safety and

health, Protective equipment.

29 CFR Parts 1950 and 1951

Grant programs--health, Grant programs--labor, Occupational safety

and health, Reporting and recordkeeping requirements.

V. Authority

This document was prepared under the direction of Joseph A. Dear,

Assistant Secretary of Labor for Occupational Safety and Health, U.S.

Department of Labor, 200 Constitution Avenue, N.W., Washington, D.C.

20210.

Signed at Washington, D.C., this 8th day of February, 1996.

Joseph A. Dear,

Assistant Secretary of Labor.

Accordingly, pursuant to sections 4, 6, and 8 of the Occupational

Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657), sec. 107 of

the Contract Work Hours and Safety Standards Act (40 U.S.C. 333), and

Secretary of Labor's Order No. 1-90 (55 FR 9033), title 29 CFR chapter

XVII is amended as set forth below.

PART 1901--[REMOVED AND RESERVED]

1. Part 1901 is removed and reserved.

PART 1902--STATE PLANS FOR THE DEVELOPMENT AND ENFORCEMENT OF STATE

STANDARDS

1. The authority citation for part 1902 continues to read as

follows:

Authority: Secs. 8 and 18 of the Occupational Safety and Health

Act of 1970, 29 U.S.C. 657 and 667.

2. Paragraph (a) of Sec. 1902.1 is revised to read as follows:

Sec. 1902.1 Purpose and scope.

(a) This part applies the provisions of section 18 of the Williams-

Steiger Occupational Safety and Health Act of 1970 (hereinafter

referred to as the Act) relating to State plans for the development and

enforcement of State occupational safety and health standards. The

provisions of the part set forth the procedures by which the Assistant

Secretary for Occupational Safety and Health (hereinafter referred to

as the Assistant Secretary) under a delegation of authority from the

Secretary of Labor (Secretary's Order No. 12-71, 36 FR 8754, May 12,

1971) will approve or reject State plans submitted to the Secretary. In

the Act, Congress declared it to be its purpose and policy ``* * * to

assure so far as possible every working man and woman in the Nation

safe and healthful working conditions and to preserve our human

resources'' by, among other actions and programs, ``* * * encouraging

the State to assume the fullest responsibility for the administration

and enforcement of their occupational safety and health laws. Section

18(a) of the Act is read as preventing any State agency or court from

asserting jurisdiction under State law over any occupational safety or

health issue with respect to which a Federal standard has been issued

under section 6 of the Act. However, section 18(b) provides that any

State that desires to assume responsibility for the development and

enforcement therein of occupational safety and health standards

relating to issues covered by corresponding standards promulgated under

section 6 of the Act shall submit a plan for doing so to the Assistant

Secretary.

* * * * *

PART 1910--OCCUPATIONAL SAFETY AND HEALTH STANDARDS

Subpart A--General

1. The authority citation for subpart A is revised to read as

follows:

[[Page 9231]]

Authority: Secs. 4, 6 and 8 of the Occupational Safety and

Health Act of 1910 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754); 8-76 (41 FR 25059); 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911; 5

U.S.C. 553.

2. In Sec. 1910.6, paragraph (a) is redesignated as paragraph

(a)(1); paragraph (b) is redesignated as paragraph (a)(3) and revised;

paragraph (c) is redesignated as paragraph (a)(2); and new paragraphs

(a)(4) and (b) through (w) are added to read as follows:

Sec. 1910.6 Incorporation by reference.

(a) * * *

(3) The materials listed in paragraphs (b) through (w) of this

section are incorporated by reference in the corresponding sections

noted as they exist on the date of the approval, and a notice of any

change in these materials will be published in the Federal Register.

These incorporations by reference were approved by the Director of the

Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.

(4) Copies of the following standards that are issued by the

respective private standards organizations may be obtained from the

issuing organizations. The materials are available for purchase at the

corresponding addresses of the private standards organizations noted

below. In addition, all are available for inspection at the Office of

the Federal Register, 800 North Capitol Street, NW., suite 700,

Washington DC, and through the OSHA Docket Office, room N2625, U.S.

Department of Labor, 200 Constitution Ave., Washington, DC 20210, or

any of its regional offices.

(b) The following material is available for purchase from the

American Conference of Governmental Industrial Hygienists (ACGIH), 1014

Broadway, Cincinnati OH 45202:

(1) ACGIH Manual ``Industrial Ventilation'' (1970), incorporation

by reference (IBR) approved for Sec. 1910.94(d) (7)(iv) and (8)(i).

(2) Threshold Limit Values and Biological Exposure Indices for

1986-87 (1986), IBR approved for Sec. 1910.120, PEL definition.

(c) The following material is available for purchase from the

American Society of Agricultural Engineers (ASAE), 2950 Niles Road,

Post Office Box 229, St. Joseph, MI 49085:

(1) ASAE Emblem for Identifying Slow Moving Vehicles, ASAE S276.2

(1968), IBR approved for Sec. 1910.145(d)(10).

(2) [Reserved]

(d) The following material is available for purchase from the

Agriculture Ammonia Institute-Rubber Manufacturers (AAI-RMA)

Association, 1400 K St. NW, Washington DC 20005:

(1) AAI-RMA Specifications for Anhydrous Ammonia Hose, IBR approved

for Sec. 1910.111(b)(8)(i).

(2) [Reserved]

(e) The following material is available for purchase from the

American National Standards Institute (ANSI), 11 West 42nd St., New

York, NY 10036:

(1) ANSI A10.2-44 Safety Code for Building Construction, IBR

approved for Sec. 1910.144(a)(1)(ii).

(2) ANSI A10.3-70 Safety Requirements for Explosive-Actuated

Fastening Tools, IBR approved for Sec. 1910.243(d)(1)(i).

(3) ANSI A11.1-65 (R 70) Practice for Industrial Lighting, IBR

approved for Secs. 1910.219(c)(5)(iii); 1910.261 (a)(3)(i), (c)(10),

and (k)(21); and 1910.265(c)(2).

(4) ANSI A11.1-65 Practice for Industrial Lighting, IBR approved

for Secs. 1910.262(c)(6) and 1910.265(d)(2)(i)(a).

(5) ANSI A12.1-67 Safety Requirements for Floor and Wall Openings,

Railings, and Toe Boards, IBR approved for Secs. 1910.66 Appendix D,

(c)(4); 1910.68 (b)(4) and (b)(8)(ii); 1910.261 (a)(3)(ii), (b)(3),

(c)(3)(i), (c)(15)(ii), (e)(4), (g)(13), (h)(1), (h)(3)(vi), (j)(4)

(ii) and (iv), (j)(5)(i), (k)(6), (k)(13)(i), and (k)(15).

(6) ANSI A13.1-56 Scheme for the Identification of Piping Systems,

IBR approved for Secs. 1910.253(d)(4)(ii); 1910.261(a)(3)(iii);

1910.262(c)(7).

(7) ANSI A14.1-68 Safety Code for Portable Wood Ladders,

Supplemented by ANSI A14.1a-77, IBR approved for Sec. 1910.261

(a)(3)(iv) and (c)(3)(i).

(8) ANSI A14.2-56 Safety Code for Portable Metal Ladders,

Supplemented by ANSI A14.2a-77, IBR approved for Sec. 1910.261

(a)(3)(v) and (c)(3)(i).

(9) ANSI A14.3-56 Safety Code for Fixed Ladders, IBR approved for

Secs. 1910.68(b) (4) and (12); 1910.179(c)(2); and 1910.261 (a)(3)(vi)

and (c)(3)(i).

(10) ANSI A17.1-65 Safety Code for Elevators, Dumbwaiters and

Moving Walks, Including Supplements, A17.1a (1967); A17.1b (1968);

A17.1c (1969); A17.1d (1970), IBR approved for Sec. 1910.261

(a)(3)(vii), (g)(11)(i), and (l)(4).

(11) ANSI A17.2-60 Practice for the Inspection of Elevators,

Including Supplements, A17.2a (1965), A17.2b (1967), IBR approved for

Sec. 1910.261(a)(3)(viii).

(12) ANSI A90.1-69 Safety Standard for Manlifts, IBR approved for

Sec. 1910.68(b)(3).

(13) ANSI A92.2-69 Standard for Vehicle Mounted Elevating and

Rotating Work Platforms, IBR approved for Sec. 1910.67 (b)(1), (2),

(c)(3), and (4) and 1910.268(s)(1)(v).

(14) ANSI A120.1-70 Safety Code for Powered Platforms for Exterior

Building Maintenance, IBR approved for Sec. 1910.66 App. D (b) through

(d).

(15) ANSI B7.1-70 Safety Code for the Use, Care and Protection of

Abrasive Wheels, IBR approved for Secs. 1910.94(b)(5)(i)(a);

1910.215(b)(12); and 1910.218(j)(5).

(16) ANSI B15.1-53 (R 58) Safety Code for Mechanical Power

Transmission Apparatus, IBR approved for Secs. 1910.68(b)(4) and

1910.261 (a)(3)(ix), (b)(1), (e)(3), (e)(9), (f)(4), (j)(5)(iv),

(k)(12), and (l)(3).

(17) ANSI B20.1-57 Safety Code for Conveyors, Cableways, and

Related Equipment, IBR approved for Secs. 1910.218(j)(3); 1910.261

(a)(3)(x), (b)(1), (c)(15)(iv), (f)(4), and (j)(2); 1910.265(c)(18)(i).

(18) ANSI B30.2-43 (R 52) Safety Code for Cranes, Derricks, and

Hoists, IBR approved for Sec. 1910.261 (a)(3)(xi), (c)(2)(vi), and

(c)(8) (i) and (iv).

(19) ANSI B30.2.0-67 Safety Code for Overhead and Gantry Cranes,

IBR approved for Secs. 1910.179(b)(2); 1910.261 (a)(3)(xii), (c)(2)(v),

and (c)(8) (i) and (iv).

(20) ANSI B30.5-68 Safety Code for Crawler, Locomotive, and Truck

Cranes, IBR approved for Secs. 1910.180(b)(2) and 1910.261(a)(3)(xiii).

(21) ANSI B30.6-69 Safety Code for Derricks, IBR approved for

Secs. 1910.181(b)(2) and 1910.268(j)(4)(iv) (E) and (H).

(22) ANSI B31.1-55 Code for Pressure Piping, IBR approved for

Sec. 1910.261(g)(18)(iii).

(23) ANSI B31.1-67, IBR approved for Sec. 1910.253(d)(1)(i)(A)

(24) ANSI B31.1a-63 Addenda to ANSI B31.1 (1955), IBR approved for

Sec. 1910.261(g)(18)(iii).

(25) ANSI B31.1-67 and Addenda B31.1 (1969) Code for Pressure

Piping, IBR approved for Secs. 1910.103(b)(1)(iii)(b);

1910.104(b)(5)(ii); 1910.218 (d)(4) and (e)(1)(iv); and 1910.261

(a)(3)(xiv) and (g)(18)(iii).

(26) ANSI B31.2-68 Fuel Gas Piping, IBR approved for

Sec. 1910.261(g)(18)(iii).

(27) ANSI B31.3-66 Petroleum Refinery Piping, IBR approved for

Sec. 1910.103(b)(3)(v)(b).

(28) ANSI B31.5-66 Addenda B31.5a (1968) Refrigeration Piping, IB

approved for Secs. 1910.103(b)(3)(v)(b) and 1910.111(b)(7)(iii).

(29) ANSI B56.1-69 Safety Standard for Powered Industrial Trucks,

IBR approved for Secs. 1910.178(a) (2) and (3) and 1910.261 (a)(3)(xv),

(b)(6), (m)(2), and (m)(5)(iii).

[[Page 9232]]

(30) ANSI B57.1-65 Compressed Gas Cylinder Valve Outlet and Inlet

Connections, IBR approved for Sec. 1910.253(b)(1)(iii).

(31) ANSI B71.1-68 Safety Specifications for Power Lawn Mowers, IBR

approved for Sec. 1910.243(e)(1)(i).

(32) ANSI B175.1-1991, Safety Requirements for Gasoline-Powered

Chain Saws 1910.266(e)(2)(i).

(33) ANSI C1-71 National Electrical Code, IBR approved for

Sec. 1910.66 Appendix D (c)(22) (i) and (vii).

(34) ANSI C33.2-56 Safety Standard for Transformer-Type Arc Welding

Machines, IBR approved for Sec. 1910.254(b)(1).

(35) ANSI D8.1-67 Practices for Railroad Highway Grade Crossing

Protection, IBR approved for Sec. 1910.265(c)(31)(i).

(36) ANSI H23.1-70 Seamless Copper Water Tube Specification, IBR

approved for Sec. 1910.110(b) (8)(ii) and (13)(ii)(b)(1).

(37) ANSI H38.7-69 Specification for Aluminum Alloy Seamless Pipe

and Seamless Extruded Tube, IBR approved for Sec. 1910.110(b)(8)(i).

(38) ANSI J6.4-71 Standard Specification for Rubber Insulating

Blankets, IBR approved for Sec. 1910.268 (f)(1) and (n)(11)(v).

(39) ANSI J6.6-71 Standard Specification for Rubber Insulating

Gloves, IBR approved for Sec. 1910.268 (f)(1) and (n)(11)(iv).

(40) ANSI K13.1-67 Identification of Gas Mask Canisters, IBR

approved for Sec. 1910.261 (a)(3)(xvi) and (h)(2)(iii).

(41) ANSI K61.1-60 Safety Requirements for the Storage and Handling

of Anhydrous Ammonia, IBR approved for Sec. 1910.111(b)(11)(i).

(42) ANSI K61.1-66 Safety Requirements for the Storage and Handling

of Anhydrous Ammonia, IBR approved for Sec. 1910.111(b)(11)(i).

(43) ANSI O1.1-54 (R 61) Safety Code for Woodworking Machinery, IBR

approved for Sec. 1910.261 (a)(3)(xvii), (e)(7), and (i)(2).

(44) ANSI S1.4-71 (R 76) Specification for Sound Level Meters, IBR

approved for Sec. 1910.95 Appendixes D and I.

(45) ANSI S1.11-71 (R 76) Specification for Octave, Half-Octave and

Third-Octave Band Filter Sets, IBR approved for Sec. 1910.95 Appendix

D.

(46) ANSI S3.6-69 Specifications for Audiometers, IBR approved for

Sec. 1910.95(h)(2) and (5)(ii) and Appendix D.

(47) ANSI Z4.1-68 Requirements for Sanitation in Places of

Employment, IBR approved for Sec. 1910.261 (a)(3)(xviii) and

(g)(15)(vi).

(48) ANSI Z4.2-42 Standard Specifications for Drinking Fountains,

IBR approved for Sec. 1910.142(c)(4).

(49) ANSI Z9.1-51 Safety Code for Ventilation and Operation of Open

Surface Tanks, IBR approved for Secs. 1910.94(c)(5)(iii)(e) and

1910.261 (a)(3)(xix), (g)(18)(v), and (h)(2)(i).

(50) ANSI Z9.2-60 Fundamentals Governing the Design and Operation

of Local Exhaust Systems, IBR approved for Secs. 1910.94 (a)(4)(i)

introductory text, (a)(6) introductory text, (b)(3)(ix), (b)(4) (i) and

(ii), (c)(3)(i) introductory text, (c)(5)(iii)(b), (c)(7)(iv)(a),

(d)(1)(ii), (d)(3), (d)(7)(iv), (d)(8)(i); 1910.261 (a)(3)(xx), (g)(1)

(i) and (iii), and (h)(2)(ii).

(51) ANSI Z12.12-68 Standard for the Prevention of Sulfur Fires and

Explosions, IBR approved for Sec. 1910.261 (a)(3)(xxi), (d)(1)(i),

(f)(2)(iv), and (g)(1)(i).

(52) ANSI Z12.20-62 (R 69) Code for the Prevention of Dust

Explosions in Woodworking and Wood Flour Manufacturing Plants, IBR

approved for Sec. 1910.265(c)(20)(i).

(53) ANSI Z21.30-64 Requirements for Gas Appliances and Gas Piping

Installations, IBR approved for Sec. 1910.265(c)(15).

(54) ANSI Z24.22-57 Method of Measurement of Real-Ear Attenuation

of Ear Protectors at Threshold, IBR approved for

Sec. 1910.261(a)(3)(xxii).

(55) ANSI Z33.1-61 Installation of Blower and Exhaust Systems for

Dust, Stock, and Vapor Removal or Conveying, IBR approved for

Secs. 1910.94(a)(4)(i); 1910.261 (a)(3)(xxiii) and (f)(5); and

1910.265(c)(20)(i).

(56) ANSI Z33.1-66 Installation of Blower and Exhaust Systems for

Dust, Stock, and Vapor Removal or Conveying, IBR approved for

Sec. 1910.94(a)(2)(ii).

(57) ANSI Z35.1-68 Specifications for Accident Prevention Signs,

IBR approved for Sec. 1910.261 (a)(3)(xxiv) and (c)(16).

(58) ANSI Z41.1-67 Men's Safety Toe Footwear, IBR approved for

Secs. 1910.94(a)(5)(v); 1910.136(b)(2) and 1910.261(i)(4).

(59) ANSI Z41-91, Personal Protection-Protective Footwear, IBR

approved for Sec. 1910.136(b)(1).

(60) ANSI Z48.1-54 Method for Marking Portable Compressed Gas

Containers to Identify the Material Contained, IBR approved for

Secs. 1910.103(b)(1)(i)(c); 1910.110(b)(5)(iii); and

1910.253(b)(1)(ii).

(61) ANSI Z48.1-54 (R 70) Method for Marking Portable Compressed

Gas Containers To Identify the Material Contained, IBR approved for

Secs. 1910.111(e)(1) and 1910.134(d)(4).

(62) ANSI Z49.1-67 Safety in Welding and Cutting, IBR approved for

Sec. 1910.252(c)(1)(iv) (A) and (B).

(63) ANSI Z53.1-67 Safety Color Code for Marking Physical Hazards

and the Identification of Certain Equipment, IBR approved for

Secs. 1910.97(a)(3)(ii); 1910.145(d) (2), (4), and (6).

(64) ANSI Z54.1-63 Safety Standard for Non-Medical X-Ray and Sealed

Gamma Ray Sources, IBR approved for Sec. 1910.252(d) (1)(vii) and

(2)(ii).

(65) ANSI Z87.1-68 Practice of Occupational and Educational Eye and

Face Protection, IBR approved for Secs. 1910.133(b)(2);

1910.252(b)(2)(ii)(I); and 1910.261 (a)(3)(xxv), (d)(1)(ii), (f)(5),

(g)(10), (g)(15)(v), (g)(18)(ii), and (i)(4).

(66) ANSI Z87.1-89, Practice for Occupational and Educational Eye

and Face Protection, IBR approved for Sec. 1910.133(b)(1).

(67) ANSI Z88.2-69 Practices for Respiratory Protection, IBR

approved for Secs. 1910.94(c)(6)(iii)(a); 1910.134(c); and 1910.261

(a)(3)(xxvi), (b)(2), (f)(5), (g)(15)(v), (h)(2) (iii) and (iv), and

(i)(4).

(68) ANSI Z89.1-69 Safety Requirements for Industrial Head

Protection, IBR approved for Secs. 1910.135(b)(2); and 1910.261

(a)(3)(xxvii), (b)(2), (g)(15)(v), and (i)(4).

(69) ANSI Z89.1-86, Protective Headwear for Industrial Workers

Requirements, IBR approved for Sec. 1910.135(b)(1).

(70) ANSI Z89.2-71 Safety Requirements for Industrial Protective

Helmets for Electrical Workers, Class B, IBR approved for

Sec. 1910.268(i)(1).

(f) The following material is available for purchase from the

American Petroleum Institute (API), 1220 L Street NW, Washington DC

20005:

(1) API 12A (Sept. 1951) Specification for Oil Storage Tanks With

Riveted Shells, 7th Ed., IBR approved for Sec. 1910.106(b)(1)(i)(a)(2).

(2) API 12B (May 1958) Specification for Bolted Production Tanks,

11th Ed., With Supplement No. 1, Mar. 1962, IBR approved for

Sec. 1910.106(b)(1)(i)(a)(3).

(3) API 12D (Aug. 1957) Specification for Large Welded Production

Tanks, 7th Ed., IBR approved for Sec. 1910.106(b)(1)(i)(a)(3).

(4) API 12F (Mar. 1961) Specification for Small Welded Production

Tanks, 5th Ed., IBR approved for Sec. 1910.106(b)(1)(i)(a)(3).

(5) API 620, Fourth Ed. (1970) Including Appendix R, Recommended

Rules for Design and Construction of Large Welded Low Pressure Storage

Tanks, IBR approved for Secs. 1910.103(c)(1)(i)(a);

1910.106(b)(1)(iv)(b)(1); and 1910.111(d)(1) (ii) and (iii).

(6) API 650 (1966) Welded Steel Tanks for Oil Storage, 3rd Ed., IBR

approved for Sec. 1910.106(b)(1)(iii)(a)(2).

[[Page 9233]]

(7) API 1104 (1968) Standard for Welding Pipelines and Related

Facilities, IBR approved for Sec. 1910.252(d)(1)(v).

(8) API 2000 (1968) Venting Atmospheric and Low Pressure Storage

Tanks, IBR approved for Sec. 1910.106(b)(2)(iv)(b)(1).

(9) API 2201 (1963) Welding or Hot Tapping on Equipment Containing

Flammables, IBR approved for Sec. 1910.252(d)(1)(vi).

(g) The following material is available for purchase from the

American Society of Mechanical Engineers (ASME), United Engineering

Center, 345 East 47th Street, New York, NY 10017:

(1) ASME Boiler and Pressure Vessel Code, Sec. VIII, 1949, 1950,

1952, 1956, 1959, and 1962 Ed., IBR approved for Secs. 1910.110

(b)(10)(iii) (Table H-26), (d)(2) (Table H-31); (e)(3)(i) (Table H-32),

(h)(2) (Table H-34); and 1910.111(b)(2)(vi);

(2) ASME Code for Pressure Vessels, 1968 Ed., IBR approved for

Secs. 1910.106(i)(3)(i); 1910.110(g)(2)(iii)(b)(2); and

1910.217(b)(12);

(3) ASME Boiler and Pressure Vessel Code, Sec. VIII, 1968, IBR

approved for Secs. 1910.103; 1910.104(b)(4)(ii); 1910.106

(b)(1)(iv)(b)(2) and (i)(3)(ii); 1910.107; 1910.110(b)(11) (i)(b) and

(iii)(a)(1); 1910.111(b)(2) (i), (ii), and (iv); and 1910.169(a)(2) (i)

and (ii);

(4) ASME Boiler and Pressure Vessel Code, Sec. VIII, Paragraph UG-

84, 1968, IBR approved for Sec. 1910.104 (b)(4)(ii) and (b)(5)(iii);

(5) ASME Boiler and Pressure Vessel Code, Sec. VIII, Unfired

Pressure Vessels, Including Addenda (1969), IBR approved for

Secs. 1910.261; 1910.262; 1910.263(i)(24)(ii);

(6) Code for Unfired Pressure Vessels for Petroleum Liquids and

Gases of the API and the ASME, 1951 Ed., IBR approved for

Sec. 1910.110(b)(3)(iii); and

(7) ASME B56.6-1992 (with addenda), Safety Standard for Rough

Terrain Forklift Trucks, IBR approved for Sec. 1910.266(f)(4).

(h) The following material is available for purchase from the

American Society for Testing and Materials (ASTM), 1916 Race Street,

Philadelphia, PA 19103:

(1) ASTM A 47-68 Malleable Iron Castings, IBR approved for

Sec. 1910.111(b)(7)(vi).

(2) ASTM A 53-69 Welded and Seamless Steel Pipe, IBR approved for

Secs. 1910.110(b)(8)(i) (a) and (b) and 1910.111(b)(7)(iv).

(3) ASTM A 126-66 Gray Iron Casting for Valves, Flanges and Pipe

Fitting, IBR approved for Sec. 1910.111(b)(7)(vi).

(4) ASTM A 391-65 (ANSI G61.1-1968) Alloy Steel Chain, IBR approved

for Sec. 1910.184(e)(4).

(5) ASTM A 395-68 Ductile Iron for Use at Elevated Temperatures,

IBR approved for Sec. 1910.111(b)(7)(vi).

(6) ASTM B 88-69 Seamless Copper Water Tube, IBR approved for

Sec. 1910.110(b) (8)(i)(a) and (13)(ii)(b)(1).

(7) ASTM B 88-66A Seamless Copper Water Tube, IBR approved for

Sec. 1910.252(d)(1)(i)(A)(2).

(8) ASTM B 117-64 Salt Spray (Fog) Test, IBR approved for

Sec. 1910.268(g)(2)(i)(A).

(9) ASTM B 210-68 Aluminum-Alloy Drawn Seamless Tubes, IBR approved

for Sec. 1910.110(b)(8)(ii).

(10) ASTM B 241-69, IBR approved for Sec. 1910.110(b)(8)(i)

introductory text.

(11) ASTM D 5-65 Test for Penetration by Bituminous Materials, IBR

approved for Sec. 1910.106(a)(17).

(12) ASTM D 56-70 Test for Flash Point by Tag Closed Tester, IBR

approved for Sec. 1910.106(a)(14)(i).

(13) ASTM D 86-62 Test for Distillation of Petroleum Products, IBR

approved for Secs. 1910.106(a)(5) and 1910.119(b) ``Boiling point.''

(14) ASTM D 88-56 Test for Saybolt Viscosity, IBR approved for

Sec. 1910.106(a)(37).

(15) ASTM D 93-71 Test for Flash Point by Pensky Martens, IBR

approved for Sec. 1910.106(a)(14)(ii).

(16) ASTM D 323-68, IBR approved for Sec. 1910.106(a)(30)

(17) ASTM D 445-65 Test for Viscosity of Transparent and Opaque

Liquids, IBR approved for Sec. 1910.106(a)(37).

(18) ASTM D 1692-68 Test for Flammability of Plastic Sheeting and

Cellular Plastics, IBR approved for Sec. 1910.103(c)(1)(v)(d).

(19) ASTM D 2161-66 Conversion Tables For SUS, IBR approved for

Sec. 1910.106(a)(37).

(i) The following material is available for purchase from the

American Welding Society (AWS), 550 NW, LeJeune Road, P.O. Box 351040,

Miami FL 33135:

(1) AWS A3.0 (1969) Terms and Definitions, IBR approved for

Sec. 1910.251(c).

(2) AWS A6.1 (1966) Recommended Safe Practices for Gas Shielded Arc

Welding, IBR approved for Sec. 1910.254(d)(1).

(3) AWS B3.0-41 Standard Qualification Procedure, IBR approved for

Sec. 1910.67(c)(5)(i).

(4) AWS D1.0-1966 Code for Welding in Building Construction, IBR

approved for Sec. 1910.27(b)(6).

(5) AWS D2.0-69 Specifications for Welding Highway and Railway

Bridges, IBR approved for Sec. 1910.67(c)(5)(iv).

(6) AWS D8.4-61 Recommended Practices for Automotive Welding

Design, IBR approved for Sec. 1910.67(c)(5)(ii).

(7) AWS D10.9-69 Standard Qualification of Welding Procedures and

Welders for Piping and Tubing, IBR approved for

Sec. 1910.67(c)(5)(iii).

(j) The following material is available for purchase from the

Department of Commerce:

(1) Commercial Standard, CS 202-56 (1961) ``Industrial Lifts and

Hinged Loading Ramps,'' IBR approved for Sec. 1910.30(a)(3).

(2) Publication ``Model Performance Criteria for Structural Fire

Fighters' Helmets,'' IBR approved for Sec. 1910.156(e)(5)(i).

(k) The following material is available for purchase from the

Compressed Gas Association (CGA), 1235 Jefferson Davis Highway,

Arlington, VA 22202:

(1) CGA C-6 (1968) Standards for Visual Inspection of Compressed

Gas Cylinders, IBR approved for Sec. 1910.101(a).

(2) CGA C-8 (1962) Standard for Requalification of ICC-3HT

Cylinders, IBR approved for Sec. 1910.101(a).

(3) CGA G-1 (1966) Acetylene, IBR approved for Sec. 1910.102(a).

(4) CGA G-1.3 (1959) Acetylene Transmission for Chemical Synthesis,

IBR approved for Sec. 1910.102(b).

(5) CGA G-1.4 (1966) Standard for Acetylene Cylinder Charging

Plants, IBR approved for Sec. 1910.102(b).

(6) CGA G-7.1 (1966) Commodity Specification, IBR approved for

Sec. 1910.134(d)(1).

(7) CGA G-8.1 (1964) Standard for the Installation of Nitrous Oxide

Systems at Consumer Sites, IBR approved for Sec. 1910.105.

(8) CGA P-1 (1965) Safe Handling of Compressed Gases, IBR approved

for Sec. 1910.101(b).

(9) CGA P-3 (1963) Specifications, Properties, and Recommendations

for Packaging, Transportation, Storage and Use of Ammonium Nitrate, IBR

approved for Sec. 1910.109(i)(1)(ii)(b).

(10) CGA S-1.1 (1963) and 1965 Addenda. Safety Release Device

Standards--Cylinders for Compressed Gases, IBR approved for

Secs. 1910.101(c); 1910.103(c)(1)(iv)(a)(2).

(11) CGA S-1.2 (1963) Safety Release Device Standards, Cargo and

Portable Tanks for Compressed Gases, IBR approved for

Secs. 1910.101(c); 1910.103(c)(1)(iv)(a)(2).

(12) CGA S-1.3 (1959) Safety Release Device Standards-Compressed

Gas Storage Containers, IBR approved for

Secs. 1910.103(c)(1)(iv)(a)(2); 1910.104(b)(6)(iii); and

1910.111(d)(4)(ii)(b).

[[Page 9234]]

(13) CGA 1957 Standard Hose Connection Standard, IBR approved for

Sec. 1910.253(e) (4)(v) and (5)(iii).

(14) CGA and RMA (Rubber Manufacturer's Association) Specification

for Rubber Welding Hose (1958), IBR approved for

Sec. 1910.253(e)(5)(i).

(15) CGA 1958 Regulator Connection Standard, IBR approved for

Sec. 1910.253(e) (4)(iv) and (6).

(l) The following material is available for purchase from the Crane

Manufacturer's Association of America, Inc. (CMAA), 1 Thomas Circle NW,

Washington DC 20005:

(1) CMAA Specification 1B61, Specifications for Electric Overhead

Traveling Cranes, IBR approved for Sec. 1910.179(b)(6)(i).

(2) [Reserved].

(m) The following material is available for purchase from the

General Services Administration:

(1) GSA Pub. GG-B-0067b, Air Compressed for Breathing Purposes, or

Interim Federal Specifications, Apr. 1965, IBR approved for

Sec. 1910.134(d)(4).

(2) [Reserved]

(n) The following material is available for purchase from the

Department of Health and Human Services:

(1) Publication No. 76-120 (1975), List of Personal Hearing

Protectors and Attenuation Data, IBR approved for Sec. 1910.95 App. B.

(2) [Reserved]

(o) The following material is available for purchase from the

Institute of Makers of Explosives (IME), 420 Lexington Avenue, New

York, NY 10017:

(1) IME Pamphlet No. 17, 1960, Safety in the Handling and Use of

Explosives, IBR approved for Secs. 1910.261 (a)(4)(iii) and

(c)(14)(ii).

(2) [Reserved]

(p) The following material is available for purchase from the

National Electrical Manufacturer's Association (NEMA):

(1) NEMA EW-1 (1962) Requirements for Electric Arc Welding

Apparatus, IBR approved for Secs. 1910.254(b)(1).

(2) [Reserved]

(q) The following material is available for purchase from the

National Fire Protection Association (NFPA), Batterymarch Park, Quincy,

MA 02269:

(1) NFPA 30 (1969) Flammable and Combustible Liquids Code, IBR

approved for Sec. 1910.178(f)(1).

(2) NFPA 32-1970 Standard for Dry Cleaning Plants, IBR approved for

Sec. 1910.106(j)(6)(i).

(3) NFPA 33-1969 Standard for Spray Finishing Using Flammable and

Combustible Material, IBR approved for Secs. 1910.94(c) (1)(ii), (2),

(3) (i) and (iii), and (5).

(4) NFPA 34-1966 Standard for Dip Tanks Containing Flammable or

Combustible Liquids, IBR approved for Sec. 1910.94(d)(2)(iv).

(5) NFPA 35-1970 Standard for the Manufacture of Organic Coatings,

IBR approved for Sec. 1910.106(j)(6)(ii).

(6) NFPA 36-1967 Standard for Solvent Extraction Plants, IBR

approved for Sec. 1910.106(j)(6)(iii).

(7) NFPA 37-1970 Standard for the Installation and Use of

Stationary Combustion Engines and Gas Turbines, IBR approved for

Secs. 1910.106(j)(6)(iv) and 1910.110 (b)(20)(iv)(c) and (e)(11).

(8) NFPA 51B-1962 Standard for Fire Protection in Use of Cutting

and Welding Processes, IBR approved for Sec. 1910.252(a)(1)

introductory text.

(9) NFPA 54-1969 Standard for the Installation of Gas Appliances

and Gas Piping, IBR approved for Sec. 1910.110(b)(20)(iv)(a).

(10) NFPA 54A-1969 Standard for the Installation of Gas Piping and

Gas Equipment on Industrial Premises and Certain Other Premises, IBR

approved for Sec. 1910.110(b)(20)(iv)(b).

(11) NFPA 58-1969 Standard for the Storage and Handling of

Liquefied Petroleum Gases (ANSI Z106.1-1970), IBR approved for

Secs. 1910.110 (b)(3)(iv) and (i)(3) (i) and (ii); and 1910.178(f)(2).

(12) NFPA 59-1968 Standard for the Storage and Handling of

Liquefied Petroleum Gases at Utility Gas Plants, IBR approved for

Secs. 1910.110 (b)(3)(iv) and (i)(2)(iv).

(13) NFPA 62-1967 Standard for the Prevention of Dust Explosions in

the Production, Packaging, and Handling of Pulverized Sugar and Cocoa,

IBR approved for Sec. 1910.263(k)(2)(i).

(14) NFPA 68-1954 Guide for Explosion Venting, IBR approved for

Sec. 1910.94(a)(2)(iii).

(15) NFPA 70-1971 National Electrical Code, IBR approved for

Sec. 1910.66 App. D(c)(2).

(16) NFPA 78-1968 Lightning Protection Code, IBR approved for

Sec. 1910.109(i)(6)(ii).

(17) NFPA 80-1968 Standard for Fire Doors and Windows, IBR approved

for Sec. 1910.106(d)(4)(i).

(18) NFPA 80-1970 Standard for the Installation of Fire Doors and

Windows, IBR approved for Sec. 1910.253(f)(6)(i)(I).

(19) NFPA 86A-1969 Standard for Oven and Furnaces Design, Location

and Equipment, IBR approved for Secs. 1910.107 (j)(1) and (l)(3) and

1910.108 (b)(2) and (d)(2).

(20) NFPA 91-1961 Standard for the Installation of Blower and

Exhaust Systems for Dust, Stock, and Vapor Removal or Conveying (ANSI

Z33.1-61), IBR approved for Sec. 1910.107(d)(1).

(21) NFPA 91-1969 Standards for Blower and Exhaust Systems, IBR

approved for Sec. 1910.108(b)(1).

(22) NFPA 96-1970 Standard for the Installation of Equipment for

the Removal of Smoke and Grease Laden Vapors from Commercial Cooking

Equipment, IBR approved for Sec. 1910.110(b)(20)(iv)(d).

(23) NFPA 101-1970 Code for Life Safety From Fire in Buildings and

Structures, IBR approved for Sec. 1910.261(a)(4)(ii).

(24) NFPA 203M-1970 Manual on Roof Coverings, IBR approved for

Sec. 1910.109(i)(1)(iii)(c).

(25) NFPA 251-1969 Standard Methods of Fire Tests of Building

Construction and Materials, IBR approved for Secs. 1910.106 (d)(3)(ii)

introductory text and (d)(4)(i).

(26) NFPA 302-1968 Fire Protection Standard for Motor-Craft

(Pleasure and Commercial), IBR approved for Sec. 1910.265(d)(2)(iv)

introductory text.

(27) NFPA 385-1966 Recommended Regulatory Standard for Tank

Vehicles for Flammable and Combustible Liquids, IBR approved for

Sec. 1910.106(g)(1)(i)(e)(1).

(28) NFPA 496-1967 Standard for Purged Enclosures for Electrical

Equipment in Hazardous Locations, IBR approved for

Sec. 1910.103(c)(1)(ix)(e)(1).

(29) NFPA 505-1969 Standard for Type Designations, Areas of Use,

Maintenence, and Operation of Powered Industrial Trucks, IBR approved

for Sec. 1910.110(e)(2)(iv).

(30) NFPA 566-1965 Standard for the Installation of Bulk Oxygen

Systems at Consumer Sites, IBR approved for Secs. 1910.253 (b)(4)(iv)

and (c)(2)(v).

(31) NFPA 656-1959 Code for the Prevention of Dust Ignition in

Spice Grinding Plants, IBR approved for Sec. 1910.263(k)(2)(i).

(32) NFPA 1971-1975 Protective Clothing for Structural Fire

Fighting, IBR approved for Sec. 1910.156(e)(3)(ii) introductory text.

(r) The following material is available for purchase from the

National Food Plant Institute, 1700 K St. NW., Washington, DC 20006:

(1) Definition and Test Procedures for Ammonium Nitrate Fertilizer

(Nov. 1964), IBR approved for Sec. 1910.109 Table H-22, ftn. 3.

(2) [Reserved]

(s) The following material is available for purchase from the

National Institute for Occupational Safety and Health (NIOSH):

(1) Registry of Toxic Effects of Chemical Substances, 1978, IBR

approved for Sec. 1910.20(c)(13)(i) and Appendix B.

(2) Development of Criteria for Fire Fighters Gloves; Vol. II, Part

II; Test

[[Page 9235]]

Methods, 1976, IBR approved for Sec. 1910.156(e)(4)(i) introductory

text.

(3) NIOSH Recommendations for Occupational Safety and Health

Standards (Sept. 1987), IBR approved for Sec. 1910.120 PEL definition.

(t) The following material is available for purchase from the

Public Health Service:

(1) U.S. Pharmacopeia, IBR approved for Sec. 1910.134(d)(1).

(2) Publication No. 934 (1962), Food Service Sanitation Ordinance

and Code, Part V of the Food Service Sanitation Manual, IBR approved

for Sec. 1910.142(i)(1).

(u) The following material is available for purchase from the

Society of Automotive Engineers (SAE), 485 Lexington Avenue, New York,

NY 10017:

(1) SAE J185, June 1988, Recommended Practice for Access Systems

for Off-Road Machines, IBR approved for Sec. 1910.266(f)(5)(i).

(2) SAE J231, January 1981, Minimum Performance Criteria for

Falling Object Protective Structure (FOPS), IBR approved for

Sec. 1910.266(f)(3)(ii).

(3) SAE J386, June 1985, Operator Restraint Systems for Off-Road

Work Machines, IBR approved for Sec. 1910.266(d)(3)(iv).

(4) SAE J397, April 1988, Deflection Limiting Volume-ROPS/FOPS

Laboratory Evaluation, IBR approved for Sec. 1910.266(f)(3)(iv).

(5) SAE 765 (1961) SAE Recommended Practice: Crane Loading

Stability Test Code, IBR approved for Sec. 1910.180 (c)(1)(iii) and

(e)(2)(iii)(a).

(6) SAE J1040, April 1988, Performance Criteria for Rollover

Protective Structures (ROPS) for Construction, Earthmoving, Forestry

and Mining Machines, IBR approved for Sec. 1910.266(f)(3)(ii).

(v) The following material is available for purchase from the

Fertilizer Institute, 1015 18th Street NW, Washington, DC 20036:

(1) Standard M-1 (1953, 1955, 1957, 1960, 1961, 1963, 1965, 1966,

1967, 1968), Superseded by ANSI K61.1-1972, IBR approved for

Sec. 1910.111(b)(1) (i) and (iii).

(2) [Reserved]

(w) The following material is available for purchase from

Underwriters Laboratories (UL), 207 East Ohio Street, Chicago, IL

60611:

(1) UL 58-61 Steel Underground Tanks for Flammable and Combustible

Liquids, 5th Ed., IBR approved for Sec. 1910.106(b)(1)(iii)(a)(1).

(2) UL 80-63 Steel Inside Tanks for Oil-Burner Fuel, IBR approved

for Sec. 1910.106(b)(1)(iii)(a)(1).

(3) UL 142-68 Steel Above Ground Tanks for Flammable and

Combustible Liquids, IBR approved for Sec. 1910.106(b)(1)(iii)(a)(1).

Subpart B--Adoption and Extension of Established Federal Standards

3. The authority citation for subpart B is revised to read as

follows:

Authority: Secs. 4, 6 and 8 of the Occupational Safety and

Health Act, 29 U.S.C. 653, 655, 657; Walsh-Healey Act, 41 U.S.C. 35

et seq; Service Contract Act of 1965, 41 U.S.C. 351 et seq; sec.

107, Contract Work Hours and Safety Standards Act (Construction

Safety Act), 40 U.S.C. 333; sec. 41, Longshore and Harbor Workers'

Compensation Act, 33 U.S.C. 941; National Foundation of Arts and

Humanities Act, 20 U.S.C. 951 et seq.; Secretary of Labor's Order

No. 12-71 (36 FR 8754); 8-76 (41 FR 25059), 9-83 (48 FR 35736), or

1-90 (55 FR 9033), as applicable; and 29 CFR part 1911.

Sec. 1910.17 [Amended]

4. In Sec. 1910.17, paragraphs (a) and (b) are removed and reserved

and in paragraph (c), the phrase ``Except as provided in paragraph (b)

of this section, except'' which appears at the beginning of the

paragraph, is removed and the word ``Except'' is added in its place.

Subpart C--General Safety and Health Provisions

5. The authority citation for subpart C continues to read as

follows:

Authority: Sec. 8 of the Occupational Safety and Health Act, 29

U.S.C. 657; Secretary of Labor's Order No. 9-83 (48 FR 35736); and

29 CFR part 1911.

Sec. 1910.20 [Amended]

6. In the first sentence of Sec. 1910.20(c)(13)(i), the word

``least'' is revised to read ``latest'' and the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added after

the words ``Substances (RTECS)''.

Subpart D--Walking-Working Surfaces

7. The authority citation for subpart D is revised to read as

follows:

Authority: Secs. 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, and 657); Secretary of

Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48

FR 35736), or 1-90 (55 FR 9033), as applicable; and 29 CFR part

1911.

Sec. 1910.30 [Amended]

8. In Sec. 1910.30(a)(3), the phrase ``, which is incorporated by

reference as specified in Sec. 1910.6'' is added after the words

``Department of Commerce'' at the end of the paragraph.

Sec. 1910.31 [Removed]

9. Section 1910.31 is removed.

Sec. 1910.32 [Removed]

10. Section 1910.32 is removed.

Subpart E--Means of Egress

11. The authority citation for subpart E continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1910.39 [Removed]

12. Section 1910.39 is removed.

Sec. 1910.40 [Removed]

13. Section 1910.40 is removed.

Subpart F--Powered Platforms, Manlifts, and Vehicle-Mounted Work

Platforms

14. The authority citation for subpart F is revised to read as

follows:

Authority: Secs. 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, and 657); Secretary of

Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48

FR 35736), or 1-90 (55 FR 9033), as applicable; and 29 CFR part

1911.

Sec. 1910.66 [Amended]

15. Paragraph (k) of Sec. 1910.66 is removed.

Sec. 1910.67 [Amended]

16. In the introductory text to Sec. 1910.67(b)(1), at the end of

the first sentence, after the words ``including appendix,'' the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

17. In the introductory text to Sec. 1910.67(c)(5), after the words

``Society (AWS) Standards'' the phrase ``which are incorporated by

reference as specified in Sec. 1910.6,'' is added.

Sec. 1910.68 [Amended]

18. In Sec. 1910.68(b)(3), after the designation ``A90.1-1969,''

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

19. In Sec. 1910.68(b)(4), the following new final sentence is

added: ``The preceding ANSI standards are incorporated by reference as

specified in Sec. 1910.6.''

20. In Sec. 1910.68(c)(7)(ii)(b), the phrase ``subdivision (a) of

the subdivision'' is changed to read ``paragraph (c)(7)(ii)(a) of this

section''.

21. The parenthetical note entitled ``Source'' that appears at the

end of the section is removed.

Sec. 1910.69 [Removed]

22. Section 1910.69 is removed.

[[Page 9236]]

Sec. 1910.70 [Removed]

23. Section 1910.70 is removed.

Subpart G--Occupational Health and Environmental Controls

24. The authority citation for subpart G is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Sec. 1910.94 [Amended]

25. In Sec. 1910.94(a)(2)(iii), following the designation ``(NFPA

91-1961)'' that appears near the end of the second sentence, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added and the words ``Guide. NFPA 68-1954'' that appear at the end of

the paragraph are revised to read ``Guide, NFPA 68-1954, which is

incorporated by reference as specified in Sec. 1910.6''.

26. At the end of the introductory text to Sec. 1910.94(a)(4)(i),

following the designation ``ANSI Z33.1-1961,'' the phrase ``, which are

incorporated by reference as specified in Sec. 1910.6'' is added.

27. In Sec. 1910.94(a)(5)(v)(a), following the designation ``Z41.1-

1967'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

28. In Sec. 1910.94(b)(5)(i)(a), following the designation ``B7.1-

1970'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

29. In Sec. 1910.94(c)(1)(ii), following the designation ``NFPA No.

33-1969'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

30. In Sec. 1910.94(c)(4)(iii), the phrase ``subparagraph (6)(ii)

of this paragraph'' that appears at the end of the paragraph is changed

to read ``paragraph (c)(6)(ii) of this section.''

31. In Sec. 1910.94(c)(5)(i)(a), the phrase ``subdivision (iii) of

this subparagraph'' is changed to read ``paragraph (c)(5)(iii) of this

section.''

32. In Sec. 1910.94(c)(5)(iii), the bracketed designation

``[Reserved]'' for the introductory text is removed.

33. In Sec. 1910.94(c)(5)(iii)(e), following the designation

``Z9.1-1951'' that appears at the end of the first sentence, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

34. In the first sentence of Sec. 1910.94(c)(6)(ii), the phrase

``subdivision (i) of this subparagraph'' is revised to read ``paragraph

(c)(6)(i) of this section.''

35. In Sec. 1910.94(c)(6)(iii)(a), following the designation

``Z88.2-1969'' that appears near the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6,''

is added.

36. In Sec. 1910.94(c)(7)(iv)(e), the phrase ``paragraph (f) of

this subdivision'' that appears at the end of the paragraph is revised

to read ``paragraph (c)(7)(iv)(f) of this section.''

37. In Sec. 1910.94(d)(2)(iv), following the words ``Fire

Protection Association'' that appear at the end of the second sentence,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

38. In Sec. 1910.94(d)(7)(iv), following the words ``Governmental

Industrial Hygienists 1970'' that appear at the end of the first

sentence, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added.

Sec. 1910.95 [Amended]

39. In Sec. 1910.95(h)(2), following the designation ``S3.6-1969''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6,'' is added.

40. In Appendix G to Sec. 1910.95, under the heading entitled

``Where Can Equipment AND Technical Advice be Obtained,'' the last

sentence of the second paragraph is removed.

41. In Appendix G to Sec. 1910.95, the table entitled ``OSHA Onsite

Consultation Project Directory'' is removed.

42. In Appendix H to Sec. 1910.95, the telephone number for OSHA's

Technical Data Center that appears near the end of the last paragraph

is revised to read ``(202) 219-7500''.

Sec. 1910.97 [Amended]

43. In Sec. 1910.97(a)(3)(ii), following the designation ``Z53.1-

1953'' that appears near the end of the first sentence, the phrase

``which is incorporated by reference as specified in Sec. 1910.6,'' is

added.

Sec. 1910.99 [Removed]

44. Section 1910.99 is removed.

Sec. 1910.100 [Removed]

45. Section 1910.100 is removed.

Subpart H--Hazardous Materials

46. The authority citation for subpart H is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Sections 1910.103, 1910.106-1910.111, and 1910.119 are also

issued under 29 CFR part 1911.

Section 1910.119 is also issued under sec. 304, Clean Air Act

Amendments of 1990 (Pub. L. 101-549, Nov. 15, 1990, reprinted at 29

U.S.C. 655 Note (Supp. 1991)).

Section 1910.120 is also issued under sec. 126, Superfund

Amendments and Reauthorization Act of 1986 as amended (29 U.S.C. 655

Note), 5 U.S.C. 553, and 29 CFR part 1911.

Sec. 1910.101 [Amended]

47. In Sec. 1910.101(a), following the designation ``C-8-1962''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

48. In Sec. 1910.101(b), following the designation ``P-1-1965''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

49. In Sec. 1910.101(c), following the designation ``S-1.2-1963''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.102 [Amended]

50. In Sec. 1910.102(a), following the designation ``G-1-1966''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

51. In Sec. 1910.102(b), following the designation ``G-1.3-1959''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

52. In Sec. 1910.102(c), following the designation ``G-1.4-1966''

that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.103 [Amended]

53. In Sec. 1910.103(b)(1)(i)(a)(1), following the words ``Pressure

Vessels--1968'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

54. In Sec. 1910.103(b)(1)(i)(c), following the designation

``Z48.1-1954'' that appears at the end of the first sentence, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

55. In Sec. 1910.103(b)(1)(iii)(b), following the designation

``B31.1-1969'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

[[Page 9237]]

56. In Sec. 1910.103(c)(1)(i)(a), following the parenthetical

``(April 1965)'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

57. In Sec. 1910.103(c)(1)(iv)(a)(1), following the phrase ``Gas

Storage Containers'' that appears at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

58. In Sec. 1910.103(c)(1)(v)(b), following the words ``as a

guide'' that appear at the end of the paragraph, the phrase ``, which

are incorporated by reference as specified in Sec. 1910.6'' is added.

59. In Sec. 1910.103(c)(1)(v)(d), following the designation ``ASTM

Procedures D1692-68'' that appears near the end of the second sentence,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6,'' is added.

Sec. 1910.104 [Amended]

60. In Sec. 1910.104(b)(4)(ii), following the words ``Pressure

Vessels--1968'' that appear at the end of the first sentence, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

61. In Sec. 1910.105(b)(5)(ii), following the designation

``B31.10a-1969'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

62. In Sec. 1910.105(b)(6)(iii), following the designation ``S-1,

Part 3'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.105 [Amended]

63. In Sec. 1910.105, following the designation ``G-8.1-1964'' that

appears at the end of the section, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.106 [Amended]

64. In Sec. 1910.106(a)(5), following the designation ``ASTM D-86-

62'' that appears near the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6,'' is added.

65. In Sec. 1910.106(a)(14)(i), following the parenthetical

designation ``(ASTM D-56-70)'' that appears near the end of the

paragraph, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6,'' is added.

66. In Sec. 1910.106(a)(14)(ii), the following new sentence is

added at the end of the paragraph: ``The preceding ASTM standards are

incorporated by reference as specified in Sec. 1910.6.''

67. In Sec. 1910.106(a)(17), following the designation ``D-5-65''

that appears at the end of the first sentence, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

68. In Sec. 1910.106(a)(30), following the designation ``ASTM D323-

68'' that appears at the end of the paragraph, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6,'' is added.

69. In Sec. 1910.106(b)(1)(i)(a), the phrase ``(b) through (e) of

this subdivision'' that appears at the end of the paragraph is changed

to read ``paragraphs (b)(1)(i) (b) through (e) of this section''.

70. In Sec. 1910.106(b)(1)(iii)(a), at the end of the introductory

text and preceding the colon, the following phrase is added: ``the

following consensus standards that are incorporated by reference as

specified in Sec. 1910.6''.

71. In Sec. 1910.106(b)(1)(iv)(b), at the end of the introductory

text and preceding the colon, the following phrase is added: ``the

following consensus standards that are incorporated by reference as

specified in Sec. 1910.6''.

72. In Sec. 1910.106(b)(2)(ii)(b), the phrase ``subdivision (c) of

this subdivision'' that appears in the first sentence is changed to

read ``paragraph (b)(2)(ii)(c) of this section''.

73. In Sec. 1910.106(b)(2)(iv)(b)(1), following the words ``Storage

Tanks'' the phrase ``, which is incorporated by reference as specified

in Sec. 1910.6'' is added before the semicolon.

74. In Sec. 1910.106(d)(3)(ii), at the end of the first sentence in

the introductory text, following the designation ``NFPA 251-1969,'' the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6,'' is added.

75. In Sec. 1910.106(d)(4)(i), near the end of the next-to-last

sentence, the phrase ``which is incorporated by reference as specified

in Sec. 1910.6,'' is added following the designation ``NFPA 80-1968''.

76. In Sec. 1910.106(j)(6), at the end of the introductory text,

the following phrase is added immediately preceding the colon: ``that

are incorporated by reference as specified in Sec. 1910.6''.

Sec. 1910.107 [Amended]

77. In Sec. 1910.107(d)(1), the phrase ``, which is incorporated

by reference as specified in Sec. 1910.6'' is added following the

designation ``NFPA 91-1961''.

78. In Sec. 1910.107(e)(5), following the words ``Pressure

Vessels--1968'' that appear at the end of the next-to-last sentence,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

79. In Sec. 1910.107(j)(1), the phrase ``, which is incorporated by

reference as specified in Sec. 1910.6'' is added following the

designation ``NFPA 86A-1969''.

Sec. 1910.108 [Amended]

80. In Sec. 1910.108(b)(1), at the end of the second sentence,

following the designation ``(NFPA Pamphlet No. 91-1969),'' the phrase

``, which are incorporated by reference as specified in Sec. 1910.6''

is added.

81. In Sec. 1910.108(b)(2), following the designation ``(NFPA No.

86A-1969)'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.109 [Amended]

82. In Sec. 1910.109(i)(1)(ii)(b), the address ``1235 Jefferson

Davis Highway, Arlington, VA 22202'' is removed and the phrase ``which

is incorporated by reference as specified in Sec. 1910.6'' is added in

its place.

83. In Sec. 1910.109(i)(2)(iii)(c), following the designation

``NFPA 203M-1970'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

84. In Sec. 1910.109(i)(6)(ii), following the designation ``NFPA

78-1968'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.110 [Amended]

85. In Sec. 1910.110(b)(3)(i), following the words ``Pressure

Vessel code, 1968 edition'' that appear at the end of the paragraph,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

86. In Sec. 1910.110(b)(3)(iii), near the end of the first

sentence, following the words ``Mechanical Engineers,'' the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6,'' is

added.

87. In the introductory text to Sec. 1910.110(b)(5)(i), the phrase

``subparagraph (3)(i) of this paragraph, except as provided in

subparagraph (3)(iv) of this paragraph'' is revised to read ``paragraph

(b)(3)(i) of this section, except as provided in paragraph (b)(3)(iv)

of this section''.

88. In Sec. 1910.110(b)(5)(iii), following the words `` the

Material Contained'' that appear at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

[[Page 9238]]

89. In Sec. 1910.110(b)(8)(i), following the designation ``(ASTM,

B241-69)'' that appears in the middle of the second sentence of the

introductory text, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added.

90. In Sec. 1910.110(b)(8)(i)(a), following the words ``Flash

Welded Pipe'' that appear near the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6,'' is

added.

91. In Sec. 1910.110(b)(8)(ii), following the designation ``(ASTM

B88-69)'' that appears at the end of the second sentence, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

92. In Sec. 1910.110(b)(8)(ii), following the designation ``ASTM

B210-68'' that appears in the middle of the third sentence, the

parenthetical phrase ``(which is incorporated by reference as specified

in Sec. 1910.6)'' is added.

93. In Sec. 1910.110(b)(20)(iv), following the words ``with the

following'' that appear at the end of the introductory text, the phrase

``NFPA consensus standards, which are incorporated by reference as

specified in Sec. 1910.6'' is added.

94. In Sec. 1910.110(e)(2)(iv), following the designation ``NFPA

505-1969'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.111 [Amended]

95. In Sec. 1910.111(b)(1)(i), following the words ``Anhydrous

Ammonia, M-1,'' that appear near the end of the paragraph, the

parenthetical phrase ``(both of which are incorporated by reference as

specified in Sec. 1910.6)'' is added.

96. In Sec. 1910.111(b)(7)(iii), near the end of the paragraph,

following the designation ``addenda B31.1a-1968'' the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6,'' is added.

97. In Sec. 1910.111(b)(7)(iv), near the end of the first sentence,

following the words ``Flash Welded Pipe,'' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6,'' is added.

98. In Sec. 1910.111(b)(7)(vi), at the end of the paragraph,

following the words ``Class B or C,'' the phrase ``all of which are

incorporated by reference as specified in Sec. 1910.6'' are added.

99. In Sec. 1910.111(d)(1)(ii), following the designations

``R2.2.1, or R2.3'' that appear near the end of the paragraph, the

phrase ``which are incorporated by reference as specified in

Sec. 1910.6'' is added.

100. In Sec. 1910.111(d)(4)(ii)(b), in the middle of the first

sentence, following the words ``Storage Containers, 1959,'' the phrase

``which is incorporated by reference as specified in Sec. 1910.6,'' is

added.

101. In Sec. 1910.111(e)(1), following the designation ``Z48.1-1954

(R1970)'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.114 [Removed]

102. Section 1910.114 is removed.

Sec. 1910.115 [Removed]

103. Section 1910.115 is removed.

Sec. 1910.116 [Removed]

104. Section 1910.116 is removed.

Sec. 1910.119 [Amended]

105. In Sec. 1910.119(b), in the definition of ``Boiling point,''

following the designation ``ASTM D-86-62'' that appears near the end of

the paragraph, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added.

Sec. 1910.120 [Amended]

106. In Sec. 1910.120(a)(1)(i), the comma at the beginning of the

word ``uncontrolled'' near the middle of the paragraph is removed.

107. In Sec. 1910.120(a)(3), in the definition of ``published

exposure level,'' the words ``dated 1986 incorporated by reference''

that appear near the beginning of the paragraph are revised to read

``dated 1986, which is incorporated by reference as specified in

Sec. 1910.6.'' In addition, the words ``dated 1987 incorporated by

reference'' that appear at the end of the paragraph are revised to read

``dated 1987, which is incorporated by reference as specified in

Sec. 1910.6.''

Subpart I--Personal Protective Equipment

108. The authority citation for subpart I continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1910.133 [Amended]

109. In the first sentence of Sec. 1910.133(b)(1), the phrase ``as

specified in Sec. 1910.6'' is added following the words ``incorporated

by reference,'' and the remaining text to the paragraph after the first

sentence is removed.

110. In the first sentence of Sec. 1910.133(b)(2), the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6,'' is

added after the designation ``Z87.1-1968,'' and the remaining text to

the paragraph after the first sentence is removed.

Sec. 1910.135 [Amended]

111. In the first sentence of Sec. 1910.135(b)(1), the phrase ``as

specified in Sec. 1910.6'' is added before the comma that follows the

words ``incorporated by reference,'' and the remaining text to the

paragraph after the first sentence is removed.

112. In the first sentence of Sec. 1910.135(b)(2), the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6,'' is

added after the designation ``Z89.1-1969,'' and the remaining text to

the paragraph after the first sentence is removed.

Sec. 1910.136 [Amended]

113. In the first sentence of Sec. 1910.136(b)(1), the phrase ``as

specified in Sec. 1910.6'' is added before the comma that follows the

words ``incorporated by reference,'' and the remaining text to the

paragraph after the first sentence is removed.

114. In the first sentence of Sec. 1910.136(b)(2), the phrase ``as

specified in Sec. 1910.6,'' is added before the comma that follows the

words ``incorporated by reference,'' and the remaining text to the

paragraph after the first sentence is removed.

Sec. 1910.139 [Removed]

115. Section 1910.139 is removed.

Sec. 1910.140 [Removed]

116. Section 1910.140 is removed.

Subpart J--General Environmental Controls

117. The authority citation for subpart J continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sections 1910.141, 1910.142, and 1910.145-1910.147 also issued

under 29 CFR part 1911.

Sec. 1910.142 [Amended]

118. In Sec. 1910.142(c)(4), near the end of the paragraph,

following the designation ``Z42-1942,'' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6.'' is added.

119. In Sec. 1910.142(i)(1), at the end of the paragraph, following

the designation ``Publication 934 (1965)'' the phrase

[[Page 9239]]

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.144 [Amended]

120. In Sec. 1910.144(a)(1)(ii), at the end of the second sentence,

following the designation ``A10.2-1944,'' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6.'' is added.

Sec. 1910.145 [Amended]

121. In Sec. 1910.145(a)(2), the phrase ``on and after August 31,

1971,'' is removed.

122. In Sec. 1910.145(d) (2)(i), (4)(i), and (6)(i), the paragraph

designation (i) is removed from each paragraph.

123. In Sec. 1910.145(d)(2), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6.'' is added following the designation ``Z53.1-1967''.

124. In Sec. 1910.145(d)(10), at the end of the paragraph, the

phrase ``, which are incorporated by reference as specified in

Sec. 1910.6.'' is added following the designation ``(ANSI B114.1-

1971)''.

Sec. 1910.148 [Removed]

125. Section 1910.148 is removed.

Sec. 1910.149 [Removed]

126. Section 1910.149 is removed.

Sec. 1910.150 [Removed]

127. Section 1910.150 is removed.

Subpart K--Medical and First Aid

128. The authority citation for subpart K is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1910.153 [Removed]

129. Section 1910.153 is removed.

Subpart L--Fire Protection

130. The authority citation for subpart L continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1910.156 [Amended]

131. In the introductory text of Sec. 1910.156(e)(3)(ii), near the

end of the paragraph, the phrase ``which is incorporated by reference

as specified in Sec. 1910.6,'' is added following the words ``

`Structural Fire Fighting' ''.

132. In the second sentence of the introductory text to

Sec. 1910.156(e)(4)(i), near the end of the paragraph, the phrase

``which is incorporated by reference as specified in Sec. 1910.6,'' is

added following the words `` `Part II: Test Methods' ''.

133. In Sec. 1910.156(e)(5)(i), following the parenthetical

``(August 1977)'' that appears near the end of the paragraph, the

phrase ``which is incorporated by reference as specified in

Sec. 1910.6,'' is added.

Sec. 1910.157 [Amended]

134. In Sec. 1910.157(c)(5), the phrase ``The employer shall

permanently remove from service by January 1, 1982,'' that appears at

the beginning of the paragraph is revised to read ``The employer shall

remove from service''.

Sec. 1910.158 [Amended]

135. In Sec. 1910.158(c)(3)(iii), the phrase ``Beginning January 1,

1981, the'' that appears at the beginning of the paragraph is removed

and the word ``The'' is added in its place.

136. In paragraph (c)(4), the phrase ``Beginning July 1, 1981,

the'' that appears at the beginning of the paragraph is removed and the

word ``The'' is added in its place.

Subpart L, Appendix D--[Amended]

137. In Appendix D to Subpart L (Secs. 1910.155-1910.165), in the

listing for the address of OSHA's Technical Data Center that appears

almost at the end of the appendix, the telephone number ``523-9700'' is

changed to ``219-7500''.

Subpart M--Compressed Gas and Compressed Air Equipment

138. The authority citation for subpart M continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1910.169 [Amended]

139. In Sec. 1910.169(a)(2)(i), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``Code Section VIII''.

Sec. 1910.170 [Removed]

140. Section 1910.170 is removed.

Sec. 1910.171 [Removed]

141. Section 1910.171 is removed.

Subpart N--Materials Handling and Storage

142. The authority citation for subpart N is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Sec. 1910.177 [Amended]

143. In Appendix B to Sec. 1910.177, in the listing for the address

of OSHA's Publications Office that appears at the end of the appendix,

the telephone number ``523-9667'' is revised to ``219-4667''.

Sec. 1910.178 [Amended]

144. In Sec. 1910.178(a)(2), near the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``B56.1-1969''.

145. In Sec. 1910.178(f)(1), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``(NFPA No. 30-

1969)''.

146. In Sec. 1910.178(f)(2), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``(NFPA No. 58-

1969)''.

Sec. 1910.179 [Amended]

147. In Sec. 1910.179(b)(2), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``B30.2.0-1967''.

148. In Sec. 1910.179(b)(6)(i), near the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``Specification No.

61''.

149. In Sec. 1910.179(c)(2), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``A14.3-1956''.

Sec. 1910.180 [Amended]

150. In Sec. 1910.180(b)(2), at the end of the second sentence, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``B30.5-1968''.

151. In Sec. 1910.180(c)(1)(i), the phrase ``subdivisions (ii) and

(iii) of this subparagraph'' that appears at the end of the paragraph

is changed to read ``paragraphs (c)(1) (ii) and (iii) of this

section''.

152. In Sec. 1910.180(c)(1)(iii), near the end of the paragraph,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``(SAE) No. J765''.

153. In the introductory text to Sec. 1910.180(d)(3), the phrase

[[Page 9240]]

``subdivision (2)(i) of this subparagraph'' that appears near the

middle of the first sentence is changed to read ``paragraph (d)(2)(i)

of this section''.

Sec. 1910.181 [Amended]

154. In Sec. 1910.181(b)(2), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``B30.6-1969''.

Sec. 1910.182 [Removed]

155. Section 1910.182 is removed.

Sec. 1910.184 [Amended]

156. In Sec. 1910.184(e)(4), at the end of the first sentence, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``Specification A391-

65''.

Sec. 1910.189 [Removed]

157. Section 1910.189 is removed.

Sec. 1910.190 [Removed]

158. Section 1910.190 is removed.

Subpart O--Machinery and Machine Guarding

159. The authority citation for subpart 0 is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Sec. 1910.215 [Amended]

160. In Sec. 1910.215(b)(12), at the end of the first sentence, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the designation ``ANSI B7.1-1970.''

Sec. 1910.216 [Amended]

161. In Sec. 1910.216, paragraphs (a) (1) and (2) are removed and

reserved.

Sec. 1910.217 [Amended]

162. In Sec. 1910.217(b)(12), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the words ``Pressure Vessels, 1968

Edition''.

163. In Sec. 1910.217(c)(1)(ii), the phrase ``subdivision (i) of

this subparagraph'' is revised to read ``paragraph (c)(1)(i) of this

section''.

164. In Sec. 1910.217, the words ``after December 31, 1976'' that

appear at the end of paragraph (c)(3)(v) are removed.

165. In Sec. 1910.217, the words ``section. This requirement shall

be complied with by November 1, 1975;'' that appear at the end of

paragraph (c)(5)(i) are removed and ``section;'' is added in their

place.

166. In Sec. 1910.217, the phrase ``Effective February 1, 1975,

the'' that appears at the beginning of the introductory text to

paragraph (d)(1) is removed and the word ``The'' is added in its place.

167. In table O-10 following Sec. 1910.217(f)(4), the fourth entry

in the first column that reads ``1\1/2\ to 5\1/2\'' is revised to read

``3\1/2\ to 5\1/2\''.

168. In Sec. 1910.217(g), the phrase ``Director of the Office of

Standards Development'' is revised to read ``Director of the

Directorate of Safety Standards Programs''.

Sec. 1910.218 [Amended]

169. In Sec. 1910.218 (d)(4) and (e)(1)(iv), at the end of the

paragraphs, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added following the date ``April 28,

1971''.

170. In Sec. 1910.218(j)(3), at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the words ``Related Equipment.''

171. In Sec. 1910.218(j)(5), near the end of the paragraph, the

phrase ``which is incorporated by reference as specified in

Sec. 1910.6,'' is added following the words ``Abrasive Wheels.''

Sec. 1910.219 [Amended]

172. In Sec. 1910.219(c)(5)(iii), following the designation

``A11.1-1965 (R-1970)'' that appears at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

Sec. 1910.220 [Removed]

173. Section 1910.220 is removed.

Sec. 1910.221 [Removed]

174. Section 1910.221 is removed.

Sec. 1910.222 [Removed]

175. Section 1910.222 is removed.

Subpart P--Hand and Portable Powered Tools and Other Hand-Held

Equipment

176. The authority citation for subpart P is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Section 1910.243 also issued under 29 CFR part 1910.

Sec. 1910.243 [Amended]

177. In Sec. 1910.243(d)(1)(i), following the designation ``ANSI

A10.3-1970'' that appears at the end of the first sentence, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

178. In Sec. 1910.243(e)(1)(i), following the designation ``ANSI

B71.1-X1968'' that appears at the end of the first sentence, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.245 [Removed]

179. Section 1910.245 is removed.

Sec. 1910.246 [Removed]

180. Section 1910.246 is removed.

Sec. 1910.247 [Removed]

181. Section 1910.247 is removed.

Subpart Q--Welding, Cutting and Brazing

182. The authority citation for subpart Q continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059); 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 5 U.S.C. 553; 29 CFR

part 1911.

Sec. 1910.251 [Amended]

183. In Sec. 1910.251(c), the designation ``A3.0-969'' that appears

at the end of the paragraph is revised to read ``A3.0-1969'' and the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added immediately following it.

Sec. 1910.252 [Amended]

184. In Sec. 1910.252(a)(1), following the designation ``Standard

51B, 1962'' that appears at the end of the first sentence of the

introductory text, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added.

185. In Sec. 1910.252(b)(2)(ii)(I), following the words ``Face

Protection'' that appear at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

186. In Sec. 1910.252(d)(1)(v), following the designation ``API

Std. 1104-1968'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

187. In Sec. 1910.252(d)(1)(vi), following the designation ``API

Std. PSD 2201-1963'' that appears at the end of the paragraph, the

phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

188. In Sec. 1910.252(d)(1)(vii), following the designation ``ANSI

Z54.1-1963'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

[[Page 9241]]

Sec. 1910.253 [Amended]

189. In Sec. 1910.253(b)(1)(ii), following the designation ``ANSI

Z48.1-1954'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

190. In Sec. 1910.253(b)(1)(iii), following the designation ``ANSI

Z57.1-1965'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

191. In Sec. 1910.253(b)(4)(iv), following the designation ``NFPA

No. 566-1965'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

192. In the introductory text to Sec. 1910.253(d)(1)(i)(A),

following the designation ``ANSI B31.1-1967,'' the phrase ``which is

incorporated by reference as specified in Sec. 1910.6,'' is added.

193. In Sec. 1910.253(d)(1)(i)(A)(2), following the designation

``ASTM B88-66a'' that appears at the end of the paragraph, the phrase

``, which is incorporated by reference as specified in Sec. 1910.6'' is

added.

194. In Sec. 1910.253(d)(4)(ii), following the designation ``ANSI

A13.1-1956'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

195. In Sec. 1910.253(e)(4) (iv) and (v), following the words

``Compressed Gas Association'' that appear at the end of both

paragraphs, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added.

196. In Sec. 1910.253(e)(5)(i), following the words ``Rubber

Manufacturers Association'' that appear at the end of the paragraph,

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added.

197. In Sec. 1910.253(f)(6)(i)(I), following the designation ``NFPA

80-1970'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.254 [Amended]

198. In Sec. 1910.254(b)(1), following the words ``Underwriters'

Laboratories'' that appear at the end of the paragraph, the phrase ``,

both of which are incorporated by reference as specified in

Sec. 1910.6'' is added.

199. In Sec. 1910.254(d)(1), following the words ``Welding

Society'' that appear at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.256 [Removed]

200. Section 1910.256 is removed.

Sec. 1910.257 [Removed]

201. Section 1910.257 is removed.

Subpart R--Special Industries

202. The authority citation for subpart R is revised to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Sections 1910.261, 1910.262, 1910.265 through 1910.269,

1910.274, and 1910.275 also issued under 29 CFR part 1910.

Sec. 1910.261 [Amended]

203. In Sec. 1910.261(a)(3), before the colon at the end of the

introductory text, the phrase ``, which are incorporated by reference

as specified in Sec. 1910.6'' is added.

204. In the introductory text of Sec. 1910.261(a)(4), the phrase

``, which are incorporated by reference as specified in Sec. 1910.6,''

is added after the words ``following standards'' that appear at the

beginning of the sentence.

205. In Sec. 1910.261, paragraph (n) is removed.

Sec. 1910.262 [Amended]

206. In Sec. 1910.262(c)(6), following the designation ``A11.1-

1965'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

207. In Sec. 1910.262(c)(7), following the designation ``A13.1-

1956'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

208. In Sec. 1910.262(h)(1)(i), following the words ``Pressure

Vessels, 1968'' that appear at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

Sec. 1910.263 [Amended]

209. In Sec. 1910.263(i)(24)(ii), following the words ``Pressure

Vessels, 1968'' that appear at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

210. In Sec. 1910.263(k)(2)(i), the comma is removed and the word

``and'' is added in its place immediately preceding the reference

``NFPA 656-1959,'' and following the words ``Grinding Plants)'' that

appear at the end of the paragraph, the phrase ``, which are

incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.265 [Amended]

211. In Sec. 1910.265(c)(2), following the designation ``A11.1-

1965'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

212. In Sec. 1910.265(c)(15), following the designation ``Z21.30-

1964'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

213. In Sec. 1910.265(c)(18)(i), following the designation ``B20.1-

1957'' that appears at the end of the paragraph, the phrase ``, which

is incorporated by reference as specified in Sec. 1910.6'' is added.

214. In Sec. 1910.265(c)(20)(i), following the words ``Flour

Manufacturing Plants)'' that appear at the end of the paragraph, the

phrase ``, which are incorporated by reference as specified in

Sec. 1910.6'' is added.

215. In Sec. 1910.265(c)(30)(iv), following the designation

``B56.1-1969'' that appears at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

216. In Sec. 1910.265(c)(31)(i), following the words ``Crossing

Protection'' that appear in the parenthetical near the end of the

paragraph, the phrase ``, which is incorporated by reference as

specified in Sec. 1910.6'' is added within the parenthetical.

217. In Sec. 1910.265(d)(2)(i)(a), following the words ``Industrial

Lighting'' that appear at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

218. In the introductory text of Sec. 1910.265(d)(2)(iv), following

the designation ``NFPA No. 302-1968'' that appears at the end of the

paragraph, the phrase ``which is incorporated by reference as specified

in Sec. 1910.6,'' is added.

219. Paragraph (j) of Sec. 1910.265 is removed.

Sec. 1910.266 [Amended]

220. In Sec. 1910.266(d)(3)(iv), following the words ``Work

Machines'' at the end of the first sentence, the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added and

the remaining text of the paragraph after the first sentence is

removed.

221. At the end of the first sentence of Sec. 1910.266(e)(2)(i),

following the words `` `Chain Saws','' the phrase``, which is

incorporated by reference as specified in Sec. 1910.6'' is added and

the text of the paragraph after the third sentence is removed.

[[Page 9242]]

222. At the end of the first sentence of Sec. 1910.266(f)(3)(ii),

the phrase ``, which is incorporated by reference as specified in

Sec. 1910.6'' is added following the words ``Mining Machines' '' and

the remaining text of the paragraph after the first sentence is

removed.

223. In Sec. 1910.266(f)(3)(iii), at the end of the first sentence,

following the words ``Protective Structures (FOPS)'' ' the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added and the remaining text of the paragraph after the first sentence

is removed.

224. At the end of the first sentence of Sec. 1910.266(f)(3)(iv),

following the words ``Laboratory Evaluation','' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added and

the remaining text of the paragraph after the first sentence is

removed.

225. At the end of the first sentence of Sec. 1910.266(f)(4),

following the words ``Forklift Trucks','' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added and

the remaining text of the paragraph after the first sentence is

removed.

226. At the end of the first sentence of Sec. 1910.266(f)(5)(i),

following the words ``for Off-Road Machines','' the phrase ``which is

incorporated by reference as specified in Sec. 1910.6,'' is added and

the remaining text of the paragraph after the first sentence is

removed.

Sec. 1910.268 [Amended]

227. In Sec. 1910.268(f)(1), the following new sentence is added to

the end of the paragraph: ``(ANSI J6.6-1971 and ANSI J6.4-1971 are

incorporated by reference as specified in Sec. 1910.6.)''

228. In Sec. 1910.268(g)(2)(i)(A), the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added

following the designation ``B117-64'' that appears near the end of the

first sentence.

229. In Sec. 1910.268(h)(3), the phrase ``After April 30, 1975,

portable'' that appears at the beginning of the paragraph is removed

and the word ``Portable'' is added in its place.

230. In Sec. 1910.268(i)(1), the following new sentence is added at

the end of the paragraph: ``ANSI Z89.2-1971 is incorporated by

reference as specified in Sec. 1910.6.''

231. In Sec. 1910.268(j)(4)(iv)(E), following the words ``for

Derricks'' ' that appear at the end of the paragraph, the phrase ``,

which is incorporated by reference as specified in Sec. 1910.6'' is

added.

232. At the end of the first sentence of Sec. 1910.268(s)(1)(v),

following the designation ``A92.2-1969'' the phrase ``, which is

incorporated by reference as specified in Sec. 1910.6'' is added.

Sec. 1910.272 [Amended]

233. In Sec. 1910.272(k)(1), the phrase ``Not later than March 30,

1989, all'' that appears at the beginning of the paragraph is removed

and the word ``All'' is added in its place.

234. In paragraph (o)(1) introductory text, the phrase ``Not later

than April 1, 1991, all'' appearing at the beginning of the paragraph

is removed and the word ``All'' is added in its place.

235. In paragraph (p)(3), the phrase ``Not later than April 1,

1991, all'' that appears at the beginning of the paragraph is removed

and the word ``All'' is added in its place.

236. In the introductory text to paragraphs (p) (4) and (6) and in

paragraph (p)(5), the phrase ``Not later than April 1, 1991, all'' that

appears at the beginning of the paragraphs is removed and the word

``All'' is added in its place.

Sec. 1910.274 [Removed]

237. Section Sec. 1910.274 is removed.

Sec. 1910.275 [Removed]

238. Section 1910.275 is removed.

Subpart T--Commercial Diving Operations

239. The authority citation for subpart T continues to read as

follows:

Authority: Sections 4, 6, and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); sec. 107, Contract

Work Hours and Safety Standards Act (Construction Safety Act) (40

U.S.C. 333); sec. 41, Longshore and Harbor Workers' Compensation Act

(33 U.S.C. 941); Secretary of Labor's Order No. 12-71 (36 FR 87540);

8-76 (41 FR 25059); 9-83 (48 FR 35736), or 1-90 (55 FR 9033), as

applicable; and 29 CFR part 1911.

Sec. 1910.440 [Amended]

240. In Sec. 1910.440(b) (1) and (5)(ii), the phrase ``Health,

Education and Welfare'' is revised to read ``Health and Human

Services''.

Subpart Z--Toxic and Hazardous Substances

241. The authority citation for subpart Z is revised to read as

follows:

Authority: Sections 6 and 8 of the Occupational Safety and

Health Act of 1970 (29 U.S.C. 655 and 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; and 29 CFR part 1911.

All of subpart Z issued under sec. 6(b) of the Occupational

Safety and Health Act, except those substances that have exposure

limits listed in Tables Z-1, Z-2, and Z-3 of 29 CFR 1910.1000. The

latter were issued under sec. 6(a) (29 U.S.C. 655(a)).

Section 1910.1000, Tables Z-1, Z-2, and Z-3 also issued under 5

U.S.C. 553. Section 1910.1000, Tables Z-1, Z-2, and Z-3 not issued

under 29 CFR part 1911 except for the arsenic (organic compounds),

benzene, and cotton dust listings.

Section 1910.1001 also issued under sec. 107 of Contract Work

Hours and Safety Standards Act (40 U.S.C. 333) and 5 U.S.C. 553.

Section 1910.1002 not issued under 29 U.S.C. 655 or 29 CFR part

1911; also issued under 5 U.S.C. 553.

Sections 1910.1003 through 1910.1018 also issued under 29 U.S.C.

653.

Section 1910.1025 also issued under 5 U.S.C. 553 and 29 U.S.C.

653.

Sections 1910.1028 and 1910.1030 also issued under 29 U.S.C.

653.

Section 1910.1043 also issued under 5 U.S.C. 551 et seq.

Sections 1910.1045, 1910.1047, and 1910.1048 also issued under

29 U.S.C. 653.

Section 1910.1200 also issued under 5 U.S.C. 553.

Section 1910.1450 is also issued under sec. 6(b), 8(c), and

8(g)(2), Pub. L. 91-596, 84 Stat. 1593, 1599, 1600 (29 U.S.C. 655

and 657).

242. Section 1910.1003 is revised to read as follows:

Sec. 1910.1003 13 Carcinogens.

(a) Scope and application. (1) This section applies to any area in

which the 13 carcinogens addressed by this section are manufactured,

processed, repackaged, released, handled, or stored, but shall not

apply to transshipment in sealed containers, except for the labeling

requirements under paragraphs (e)(2), (3) and (4) of this section. The

13 carcinogens are the following:

4-Nitrobiphenyl, Chemical Abstracts Service Register Number (CAS

No.) 92933;

alpha-Naphthylamine, CAS No. 134327;

methyl chloromethyl ether, CAS No. 107302;

3,3'-Dichlorobenzidine (and its salts) CAS No. 91941;

bis-Chloromethyl ether, CAS No. 542881;

beta-Naphthylamine, CAS No. 91598;

Benzidine, CAS No. 92875;

4-Aminodiphenyl, CAS No. 92671;

Ethyleneimine, CAS No. 151564;

beta-Propiolactone, CAS No. 57578;

2-Acetylaminofluorene, CAS No. 53963;

4-Dimethylaminoazo-benezene, CAS No. 60117; and

N-Nitrosodimethylamine, CAS No. 62759.

(2) This section shall not apply to the following:

(i) Solid or liquid mixtures containing less than 0.1 percent by

weight or volume of 4-Nitrobiphenyl; methyl chloromethyl ether; bis-

chloromethyl ether; beta-Naphthylamine; benzidine or 4-Aminodiphenyl;

and

(ii) Solid or liquid mixtures containing less than 1.0 percent by

[[Page 9243]]

weight or volume of alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and

its salts); Ethyleneimine; beta-Propiolactone; 2-Acetylaminofluorene;

4-Dimethylaminoazobenzene, or N-Nitrosodimethylamine.

(b) Definitions. For the purposes of this section:

Absolute filter is one capable of retaining 99.97 percent of a mono

disperse aerosol of 0.3 m particles.

Authorized employee means an employee whose duties require him to

be in the regulated area and who has been specifically assigned by the

employer.

Clean change room means a room where employees put on clean

clothing and/or protective equipment in an environment free of the 13

carcinogens addressed by this section. The clean change room shall be

contiguous to and have an entry from a shower room, when the shower

room facilities are otherwise required in this section.

Closed system means an operation involving a carcinogen addressed

by this section where containment prevents the release of the material

into regulated areas, non-regulated areas, or the external environment.

Decontamination means the inactivation of a carcinogen addressed by

this section or its safe disposal.

Director means the Director, National Institute for Occupational

Safety and Health, or any person directed by him or the Secretary of

Health and Human Services to act for the Director.

Disposal means the safe removal of the carcinogens addressed by

this section from the work environment.

Emergency means an unforeseen circumstance or set of circumstances

resulting in the release of a carcinogen addressed by this section that

may result in exposure to or contact with the material.

External environment means any environment external to regulated

and nonregulated areas.

Isolated system means a fully enclosed structure other than the

vessel of containment of a carcinogen addressed by this section that is

impervious to the passage of the material and would prevent the entry

of the carcinogen addressed by this section into regulated areas,

nonregulated areas, or the external environment, should leakage or

spillage from the vessel of containment occur.

Laboratory-type hood is a device enclosed on the three sides and

the top and bottom, designed and maintained so as to draw air inward at

an average linear face velocity of 150 feet per minute with a minimum

of 125 feet per minute; designed, constructed, and maintained in such a

way that an operation involving a carcinogen addressed by this section

within the hood does not require the insertion of any portion of any

employee's body other than his hands and arms.

Nonregulated area means any area under the control of the employer

where entry and exit is neither restricted nor controlled.

Open-vessel system means an operation involving a carcinogen

addressed by this section in an open vessel that is not in an isolated

system, a laboratory-type hood, nor in any other system affording

equivalent protection against the entry of the material into regulated

areas, non-regulated areas, or the external environment.

Protective clothing means clothing designed to protect an employee

against contact with or exposure to a carcinogen addressed by this

section.

Regulated area means an area where entry and exit is restricted and

controlled.

(c) Requirements for areas containing a carcinogen addressed by

this section. A regulated area shall be established by an employer

where a carcinogen addressed by this section is manufactured,

processed, used, repackaged, released, handled or stored. All such

areas shall be controlled in accordance with the requirements for the

following category or categories describing the operation involved:

(1) Isolated systems. Employees working with a carcinogen addressed

by this section within an isolated system such as a ``glove box'' shall

wash their hands and arms upon completion of the assigned task and

before engaging in other activities not associated with the isolated

system.

(2) Closed system operation. (i) Within regulated areas where the

carcinogens addressed by this section are stored in sealed containers,

or contained in a closed system, including piping systems, with any

sample ports or openings closed while the carcinogens addressed by this

section are contained within, access shall be restricted to authorized

employees only.

(ii) Employees exposed to 4-Nitrobiphenyl; alpha-Naphthylamine;

3,3'-Dichlorobenzidine (and its salts); beta-Naphthylamine; benzidine;

4-Aminodiphenyl; 2-Acetylaminofluorene; 4-Dimethylaminoazo-benzene; and

N-Nitrosodimethylamine shall be required to wash hands, forearms, face,

and neck upon each exit from the regulated areas, close to the point of

exit, and before engaging in other activities.

(3) Open-vessel system operations. Open-vessel system operations as

defined in paragraph (b)(13) of this section are prohibited.

(4) Transfer from a closed system, charging or discharging point

operations, or otherwise opening a closed system. In operations

involving ``laboratory-type hoods,'' or in locations where the

carcinogens addressed by this section are contained in an otherwise

``closed system,'' but is transferred, charged, or discharged into

other normally closed containers, the provisions of this paragraph

shall apply.

(i) Access shall be restricted to authorized employees only.

(ii) Each operation shall be provided with continuous local exhaust

ventilation so that air movement is always from ordinary work areas to

the operation. Exhaust air shall not be discharged to regulated areas,

nonregulated areas or the external environment unless decontaminated.

Clean makeup air shall be introduced in sufficient volume to maintain

the correct operation of the local exhaust system.

(iii) Employees shall be provided with, and required to wear,

clean, full body protective clothing (smocks, coveralls, or long-

sleeved shirt and pants), shoe covers and gloves prior to entering the

regulated area.

(iv) Employees engaged in handling operations involving the

carcinogens addressed by this section shall be provided with and

required to wear and use a half-face, filter-type respirator for dusts,

mists, and fumes, in accordance with Sec. 1910.134. A respirator

affording higher levels of protection may be substituted.

(v) Prior to each exit from a regulated area, employees shall be

required to remove and leave protective clothing and equipment at the

point of exit and at the last exit of the day, to place used clothing

and equipment in impervious containers at the point of exit for

purposes of decontamination or disposal. The contents of such

impervious containers shall be identified, as required under paragraphs

(e) (2), (3), and (4) of this section.

(vi) Drinking fountains are prohibited in the regulated area.

(vii) Employees shall be required to wash hands, forearms, face,

and neck on each exit from the regulated area, close to the point of

exit, and before engaging in other activities and employees exposed to

4-Nitrobiphenyl; alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and its

salts); beta-Naphthylamine; Benzidine; 4-Aminodiphenyl; 2-

Acetylaminofluorene; 4-Dimethylaminoazo-benzene; and N-

Nitrosodimethylamine shall be required to shower after the last exit of

the day.

[[Page 9244]]

(5) Maintenance and decontamination activities. In cleanup of leaks

of spills, maintenance, or repair operations on contaminated systems or

equipment, or any operations involving work in an area where direct

contact with a carcinogen addressed by this section could result, each

authorized employee entering that area shall:

(i) Be provided with and required to wear clean, impervious

garments, including gloves, boots, and continuous-air supplied hood in

accordance with Sec. 1910.134;

(ii) Be decontaminated before removing the protective garments and

hood;

(iii) Be required to shower upon removing the protective garments

and hood.

(d) General regulated area requirements--(1) [Reserved]

(2) Emergencies. In an emergency, immediate measures including, but

not limited to, the requirements of paragraphs (d)(2) (i) through (v)

of this section shall be implemented.

(i) The potentially affected area shall be evacuated as soon as the

emergency has been determined.

(ii) Hazardous conditions created by the emergency shall be

eliminated and the potentially affected area shall be decontaminated

prior to the resumption of normal operations.

(iii) Special medical surveillance by a physician shall be

instituted within 24 hours for employees present in the potentially

affected area at the time of the emergency. A report of the medical

surveillance and any treatment shall be included in the incident

report, in accordance with paragraph (f)(2) of this section.

(iv) Where an employee has a known contact with a carcinogen

addressed by this section, such employee shall be required to shower as

soon as possible, unless contraindicated by physical injuries.

(v) An incident report on the emergency shall be reported as

provided in paragraph (f)(2) of this section.

(vi) Emergency deluge showers and eyewash fountains supplied with

running potable water shall be located near, within sight of, and on

the same level with locations where a direct exposure to Ethyleneimine

or beta-Propiolactone only would be most likely as a result of

equipment failure or improper work practice.

(3) Hygiene facilities and practices. (i) Storage or consumption of

food, storage or use of containers of beverages, storage or application

of cosmetics, smoking, storage of smoking materials, tobacco products

or other products for chewing, or the chewing of such products are

prohibited in regulated areas.

(ii) Where employees are required by this section to wash, washing

facilities shall be provided in accordance with Sec. 1910.141(d) (1)

and (2) (ii) through (vii).

(iii) Where employees are required by this section to shower,

shower facilities shall be provided in accordance with

Sec. 1910.141(d)(3).

(iv) Where employees wear protective clothing and equipment, clean

change rooms shall be provided for the number of such employees

required to change clothes, in accordance with Sec. 1910.141(e).

(v) Where toilets are in regulated areas, such toilets shall be in

a separate room.

(4) Contamination control. (i) Except for outdoor systems,

regulated areas shall be maintained under pressure negative with

respect to nonregulated areas. Local exhaust ventilation may be used to

satisfy this requirement. Clean makeup air in equal volume shall

replace air removed.

(ii) Any equipment, material, or other item taken into or removed

from a regulated area shall be done so in a manner that does not cause

contamination in nonregulated areas or the external environment.

(iii) Decontamination procedures shall be established and

implemented to remove carcinogens addressed by this section from the

surfaces of materials, equipment, and the decontamination facility.

(iv) Dry sweeping and dry mopping are prohibited for 4-

Nitrobiphenyl; alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and its

salts); beta-Naphthylamine; Benzidine; 4-Aminodiphenyl; 2-

Acetylaminofluorene; 4-Dimethylaminoazo-benzene and N-

Nitrosodimethylamine.

(e) Signs, information and training--(1) Signs--(i) Entrances to

regulated areas shall be posted with signs bearing the legend:

CANCER-SUSPECT AGENT

AUTHORIZED PERSONNEL ONLY

(ii) Entrances to regulated areas containing operations covered in

paragraph (c)(5) of this section shall be posted with signs bearing the

legend:

CANCER-SUSPECT AGENT EXPOSED IN THIS AREA

IMPERVIOUS SUIT INCLUDING GLOVES, BOOTS, AND AIR-SUPPLIED HOOD REQUIRED

AT ALL TIMES

AUTHORIZED PERSONNEL ONLY

(iii) Appropriate signs and instructions shall be posted at the

entrance to, and exit from, regulated areas, informing employees of the

procedures that must be followed in entering and leaving a regulated

area.

(2) Container contents identification. (i) Containers of a

carcinogen addressed by this section and containers required under

paragraphs (c)(4)(v) and (c)(6) (vii)(B) and (viii)(B) of this section

that are accessible only to and handled only by authorized employees,

or by other employees trained in accordance with paragraph (e)(5) of

this section, may have contents identification limited to a generic or

proprietary name or other proprietary identification of the carcinogen

and percent.

(ii) Containers of a carcinogen addressed by this section and

containers required under paragraphs (c)(4)(v) and (c)(6) (vii)(B) and

(viii)(B) of this section that are accessible to or handled by

employees other than authorized employees or employees trained in

accordance with paragraph (e)(5) of this section shall have contents

identification that includes the full chemical name and Chemical

Abstracts Service Registry number as listed in paragraph (a)(1) of this

section.

(iii) Containers shall have the warning words ``CANCER-SUSPECT

AGENT'' displayed immediately under or adjacent to the contents

identification.

(iv) Containers whose contents are carcinogens addressed by this

section with corrosive or irritating properties shall have label

statements warning of such hazards noting, if appropriate, particularly

sensitive or affected portions of the body.

(3) Lettering. Lettering on signs and instructions required by

paragraph (e)(1) shall be a minimum letter height of 2 inches (5 cm).

Labels on containers required under this section shall not be less than

one-half the size of the largest lettering on the package, and not less

than 8-point type in any instance. Provided, That no such required

lettering need be more than 1 inch (2.5 cm) in height.

(4) Prohibited statements. No statement shall appear on or near any

required sign, label, or instruction that contradicts or detracts from

the effect of any required warning, information, or instruction.

(5) Training and indoctrination. (i) Each employee prior to being

authorized

[[Page 9245]]

to enter a regulated area, shall receive a training and indoctrination

program including, but not necessarily limited to:

(A) The nature of the carcinogenic hazards of a carcinogen

addressed by this section, including local and systemic toxicity;

(B) The specific nature of the operation involving a carcinogen

addressed by this section that could result in exposure;

(C) The purpose for and application of the medical surveillance

program, including, as appropriate, methods of self-examination;

(D) The purpose for and application of decontamination practices

and purposes;

(E) The purpose for and significance of emergency practices and

procedures;

(F) The employee's specific role in emergency procedures;

(G) Specific information to aid the employee in recognition and

evaluation of conditions and situations which may result in the release

of a carcinogen addressed by this section;

(H) The purpose for and application of specific first aid

procedures and practices;

(I) A review of this section at the employee's first training and

indoctrination program and annually thereafter.

(ii) Specific emergency procedures shall be prescribed, and posted,

and employees shall be familiarized with their terms, and rehearsed in

their application.

(iii) All materials relating to the program shall be provided upon

request to authorized representatives of the Assistant Secretary and

the Director.

(f) Reports--(1) Operations. The information required in paragraphs

(f)(1) (i) through (iv) of this section shall be reported in writing to

the nearest OSHA Area Director. Any changes in such information shall

be similarly reported in writing within 15 calendar days of such

change:

(i) A brief description and in-plant location of the area(s)

regulated and the address of each regulated area;

(ii) The name(s) and other identifying information as to the

presence of a carcinogen addressed by this section in each regulated

area;

(iii) The number of employees in each regulated area, during normal

operations including maintenance activities; and

(iv) The manner in which carcinogens addressed by this section are

present in each regulated area; for example, whether it is

manufactured, processed, used, repackaged, released, stored, or

otherwise handled.

(2) Incidents. Incidents that result in the release of a carcinogen

addressed by this section into any area where employees may be

potentially exposed shall be reported in accordance with this

paragraph.

(i) A report of the occurrence of the incident and the facts

obtainable at that time including a report on any medical treatment of

affected employees shall be made within 24 hours to the nearest OSHA

Area Director.

(ii) A written report shall be filed with the nearest OSHA Area

Director within 15 calendar days thereafter and shall include:

(A) A specification of the amount of material released, the amount

of time involved, and an explanation of the procedure used in

determining this figure;

(B) A description of the area involved, and the extent of known and

possible employee exposure and area contamination;

(C) A report of any medical treatment of affected employees, and

any medical surveillance program implemented; and

(D) An analysis of the circumstances of the incident and measures

taken or to be taken, with specific completion dates, to avoid further

similar releases.

(g) Medical surveillance. At no cost to the employee, a program of

medical surveillance shall be established and implemented for employees

considered for assignment to enter regulated areas, and for authorized

employees.

(1) Examinations. (i) Before an employee is assigned to enter a

regulated area, a preassignment physical examination by a physician

shall be provided. The examination shall include the personal history

of the employee, family and occupational background, including genetic

and environmental factors.

(ii) Authorized employees shall be provided periodic physical

examinations, not less often than annually, following the preassignment

examination.

(iii) In all physical examinations, the examining physician shall

consider whether there exist conditions of increased risk, including

reduced immunological competence, those undergoing treatment with

steroids or cytotoxic agents, pregnancy, and cigarette smoking.

(2) Records. (i) Employers of employees examined pursuant to this

paragraph shall cause to be maintained complete and accurate records of

all such medical examinations. Records shall be maintained for the

duration of the employee's employment. Upon termination of the

employee's employment, including retirement or death, or in the event

that the employer ceases business without a successor, records, or

notarized true copies thereof, shall be forwarded by registered mail to

the Director.

(ii) Records required by this paragraph shall be provided upon

request to employees, designated representatives, and the Assistant

Secretary in accordance with 29 CFR 1910.20 (a) through (e) and (g)

through (i). These records shall also be provided upon request to the

Director.

(iii) Any physician who conducts a medical examination required by

this paragraph shall furnish to the employer a statement of the

employee's suitability for employment in the specific exposure.

Secs. 1910.1004-1910.1016 [Amended]

243. In Secs. 1910.1004, 1910.1006, 1910.1007, 1910.1008,

1910.1009, 1910.1010, 1910.1011, 1910.1012, 1910.1013, 1910.1014,

1910.1015, and 1910.1016, the text is removed in its entirety and

replaced with the following text (below the section heading) in each

section: ``See Sec. 1910.1003, 13 carcinogens.''.

Sec. 1910.1018 [Amended]

244. In Sec. 1910.1018(o)(1)(ii), the phrase ``and shall be

repeated at least quarterly for employees who have optional use of

respirators'' is removed.

Sec. 1910.1200 [Amended]

245. In Sec. 1910.1200, Appendix C--Information Sources (Advisory)

is removed.

Sec. 1910.1499 [Removed]

246. Section Sec. 1910.1499 is removed.

Sec. 1910.1500 [Removed]

247. Section Sec. 1910.1500 is removed.

PART 1915--OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD

EMPLOYMENT

1. The authority citation for part 1915 continues to read as

follows:

Authority: Sec. 41, Longshore and Harbor Workers Compensation

Act (33 U.S.C. 941); secs. 4, 6, and 8 of the Occupational Safety

and Health Act of 1970 (29 U.S.C. 653, 655, and 657); sec. 4 of the

Administrative Procedure Act (5 U.S.C. 553); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable; 29 CFR part 1911.

Subpart Z--Toxic and Hazardous Substances

2. Section 1915.1003 is revised to read as follows:

[[Page 9246]]

Sec. 1915.1003 13 Carcinogens.

(a) Scope and application. (1) This section applies to any area in

which the 13 carcinogens addressed by this section are manufactured,

processed, repackaged, released, handled, or stored, but shall not

apply to transshipment in sealed containers, except for the labeling

requirements under paragraphs (e) (2), (3) and (4) of this section. The

13 carcinogens are the following:

4-Nitrobiphenyl, Chemical Abstracts Service Register Number (CAS

No.) 92933;

alpha-Naphthylamine, CAS No. 134327;

methyl chloromethyl ether, CAS No. 107302;

3,3'-Dichlorobenzidine (and its salts) CAS No. 91941;

bis-Chloromethyl ether, CAS No. 542881;

beta-Naphthylamine, CAS No. 91598;

Benzidine, CAS No. 92875;

4-Aminodiphenyl, CAS No. 92671;

Ethyleneimine, CAS No. 151564;

beta-Propiolactone, CAS No. 57578;

2-Acetylaminofluorene, CAS No. 53963;

4-Dimethylaminoazo-benezene, CAS No. 60117; and

N-Nitrosodimethylamine, CAS No. 62759.

(2) This section shall not apply to the following:

(i) Solid or liquid mixtures containing less than 0.1 percent by

weight or volume of 4-Nitrobiphenyl; methyl chloromethyl ether; bis-

chloromethyl ether; beta-Naphthylamine; benzidine or 4-Aminodiphenyl;

and

(ii) Solid or liquid mixtures containing less than 1.0 percent by

weight or volume of alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and

its salts); Ethyleneimine; beta-Propiolactone; 2-Acetylaminofluorene;

4-Dimethylaminoazobenzene, or N-Nitrosodimethylamine.

(b) Definitions. For the purposes of this section:

Absolute filter is one capable of retaining 99.97 percent of a mono

disperse aerosol of 0.3 m particles.

Authorized employee means an employee whose duties require him to

be in the regulated area and who has been specifically assigned by the

employer.

Clean change room means a room where employees put on clean

clothing and/or protective equipment in an environment free of the 13

carcinogens addressed by this section. The clean change room shall be

contiguous to and have an entry from a shower room, when the shower

room facilities are otherwise required in this section.

Closed system means an operation involving a carcinogen addressed

by this section where containment prevents the release of the material

into regulated areas, non-regulated areas, or the external environment.

Decontamination means the inactivation of a carcinogen addressed by

this section or its safe disposal.

Director means the Director, National Institute for Occupational

Safety and Health, or any person directed by him or the Secretary of

Health and Human Services to act for the Director.

Disposal means the safe removal of the carcinogens addressed by

this section from the work environment.

Emergency means an unforeseen circumstance or set of circumstances

resulting in the release of a carcinogen addressed by this section that

may result in exposure to or contact with the material.

External environment means any environment external to regulated

and nonregulated areas.

Isolated system means a fully enclosed structure other than the

vessel of containment of a carcinogen addressed by this section that is

impervious to the passage of the material and would prevent the entry

of the carcinogen addressed by this section into regulated areas,

nonregulated areas, or the external environment, should leakage or

spillage from the vessel of containment occur.

Laboratory-type hood is a device enclosed on the three sides and

the top and bottom, designed and maintained so as to draw air inward at

an average linear face velocity of 150 feet per minute with a minimum

of 125 feet per minute; designed, constructed, and maintained in such a

way that an operation involving a carcinogen addressed by this section

within the hood does not require the insertion of any portion of any

employee's body other than his hands and arms.

Nonregulated area means any area under the control of the employer

where entry and exit is neither restricted nor controlled.

Open-vessel system means an operation involving a carcinogen

addressed by this section in an open vessel that is not in an isolated

system, a laboratory-type hood, nor in any other system affording

equivalent protection against the entry of the material into regulated

areas, non-regulated areas, or the external environment.

Protective clothing means clothing designed to protect an employee

against contact with or exposure to a carcinogen addressed by this

section.

Regulated area means an area where entry and exit is restricted and

controlled.

(c) Requirements for areas containing a carcinogen addressed by

this section. A regulated area shall be established by an employer

where a carcinogen addressed by this section is manufactured,

processed, used, repackaged, released, handled or stored. All such

areas shall be controlled in accordance with the requirements for the

following category or categories describing the operation involved:

(1) Isolated systems. Employees working with a carcinogen addressed

by this section within an isolated system such as a ``glove box'' shall

wash their hands and arms upon completion of the assigned task and

before engaging in other activities not associated with the isolated

system.

(2) Closed system operation. (i) Within regulated areas where the

carcinogens addressed by this section are stored in sealed containers,

or contained in a closed system, including piping systems, with any

sample ports or openings closed while the carcinogens addressed by this

section are contained within, access shall be restricted to authorized

employees only.

(ii) Employees exposed to 4-Nitrobiphenyl; alpha-Naphthylamine;

3,3'-Dichlorobenzidine (and its salts); beta-Naphthylamine; benzidine;

4-Aminodiphenyl; 2-Acetyleminofluorene; 4-Dimethylaminoazo-benzene; and

N-Nitrosodimethylamine shall be required to wash hands, forearms, face,

and neck upon each exit from the regulated areas, close to the point of

exit, and before engaging in other activities.

(3) Open-vessel system operations. Open-vessel system operations as

defined in paragraph (b)(13) of this section are prohibited.

(4) Transfer from a closed system, charging or discharging point

operations, or otherwise opening a closed system. In operations

involving ``laboratory-type hoods,'' or in locations where the

carcinogens addressed by this section are contained in an otherwise

``closed system'', but is transferred, charged, or discharged into

other normally closed containers, the provisions of this paragraph

shall apply.

(i) Access shall be restricted to authorized employees only.

(ii) Each operation shall be provided with continuous local exhaust

ventilation so that air movement is always from ordinary work areas to

the operation. Exhaust air shall not be discharged to regulated areas,

nonregulated areas or the external environment unless decontaminated.

Clean makeup air shall be introduced in sufficient volume to maintain

the correct operation of the local exhaust system.

(iii) Employees shall be provided with, and required to wear,

clean, full body protective clothing (smocks, coveralls, or long-

sleeved shirt and

[[Page 9247]]

pants), shoe covers and gloves prior to entering the regulated area.

(iv) Employees engaged in handling operations involving the

carcinogens addressed by this section shall be provided with and

required to wear and use a half-face, filter-type respirator for dusts,

mists, and fumes, in accordance with Sec. 1910.134. A respirator

affording higher levels of protection may be substituted.

(v) Prior to each exit from a regulated area, employees shall be

required to remove and leave protective clothing and equipment at the

point of exit and at the last exit of the day, to place used clothing

and equipment in impervious containers at the point of exit for

purposes of decontamination or disposal. The contents of such

impervious containers shall be identified, as required under paragraphs

(e) (2), (3), and (4) of this section.

(vi) Drinking fountains are prohibited in the regulated area.

(vii) Employees shall be required to wash hands, forearms, face,

and neck on each exit from the regulated area, close to the point of

exit, and before engaging in other activities and employees exposed to

4-Nitrobiphenyl; alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and its

salts); beta-Naphthylamine; Benzidine; 4-Aminodiphenyl; 2-

Acetylaminofluorene; 4-Dimethylaminoazo-benzene; and N-

Nitrosodimethylamine shall be required to shower after the last exit of

the day.

(5) Maintenance and decontamination activities. In cleanup of leaks

of spills, maintenance, or repair operations on contaminated systems or

equipment, or any operations involving work in an area where direct

contact with a carcinogen addressed by this section could result, each

authorized employee entering that area shall:

(i) Be provided with and required to wear clean, impervious

garments, including gloves, boots, and continuous-air supplied hood in

accordance with Sec. 1910.134;

(ii) Be decontaminated before removing the protective garments and

hood;

(iii) Be required to shower upon removing the protective garments

and hood.

(d) General regulated area requirements--(1) [Reserved]

(2) Emergencies. In an emergency, immediate measures including, but

not limited to, the requirements of paragraphs (d)(2) (i) through (v)

of this section shall be implemented.

(i) The potentially affected area shall be evacuated as soon as the

emergency has been determined.

(ii) Hazardous conditions created by the emergency shall be

eliminated and the potentially affected area shall be decontaminated

prior to the resumption of normal operations.

(iii) Special medical surveillance by a physician shall be

instituted within 24 hours for employees present in the potentially

affected area at the time of the emergency. A report of the medical

surveillance and any treatment shall be included in the incident

report, in accordance with paragraph (f)(2) of this section.

(iv) Where an employee has a known contact with a carcinogen

addressed by this section, such employee shall be required to shower as

soon as possible, unless contraindicated by physical injuries.

(v) An incident report on the emergency shall be reported as

provided in paragraph (f)(2) of this section.

(vi) Emergency deluge showers and eyewash fountains supplied with

running potable water shall be located near, within sight of, and on

the same level with locations where a direct exposure to Ethyleneimine

or beta-Propiolactone only would be most likely as a result of

equipment failure or improper work practice.

(3) Hygiene facilities and practices. (i) Storage or consumption of

food, storage or use of containers of beverages, storage or application

of cosmetics, smoking, storage of smoking materials, tobacco products

or other products for chewing, or the chewing of such products are

prohibited in regulated areas.

(ii) Where employees are required by this section to wash, washing

facilities shall be provided in accordance with Sec. 1910.141(d) (1)

and (2) (ii) through (vii).

(iii) Where employees are required by this section to shower,

shower facilities shall be provided in accordance with

Sec. 1910.141(d)(3).

(iv) Where employees wear protective clothing and equipment, clean

change rooms shall be provided for the number of such employees

required to change clothes, in accordance with Sec. 1910.141(e).

(v) Where toilets are in regulated areas, such toilets shall be in

a separate room.

(4) Contamination control. (i) Except for outdoor systems,

regulated areas shall be maintained under pressure negative with

respect to nonregulated areas. Local exhaust ventilation may be used to

satisfy this requirement. Clean makeup air in equal volume shall

replace air removed.

(ii) Any equipment, material, or other item taken into or removed

from a regulated area shall be done so in a manner that does not cause

contamination in nonregulated areas or the external environment.

(iii) Decontamination procedures shall be established and

implemented to remove carcinogens addressed by this section from the

surfaces of materials, equipment, and the decontamination facility.

(iv) Dry sweeping and dry mopping are prohibited for 4-

Nitrobiphenyl; alpha-Naphthylamine; 3,3'-Dichlorobenzidine (and its

salts); beta-Naphthylamine; Benzidine; 4-Aminodiphenyl; 2-

Acetylaminofluorene; 4-Dimethylaminoazo-benzene and N-

Nitrosodimethylamine.

(e) Signs, information and training--(1) Signs--(i) Entrances to

regulated areas shall be posted with signs bearing the legend:

CANCER-SUSPECT AGENT

AUTHORIZED PERSONNEL ONLY

(ii) Entrances to regulated areas containing operations covered in

paragraph (c)(5) of this section shall be posted with signs bearing the

legend:

CANCER-SUSPECT AGENT EXPOSED IN THIS AREA

IMPERVIOUS SUIT INCLUDING GLOVES, BOOTS, AND AIR-SUPPLIED HOOD REQUIRED

AT ALL TIMES

AUTHORIZED PERSONNEL ONLY

(iii) Appropriate signs and instructions shall be posted at the

entrance to, and exit from, regulated areas, informing employees of the

procedures that must be followed in entering and leaving a regulated

area.

(2) Container contents identification. (i) Containers of a

carcinogen addressed by this section and containers required under

paragraphs (c)(4)(v) and (c)(6) (vii)(B) and (viii)(B) of this section

that are accessible only to and handled only by authorized employees,

or by other employees trained in accordance with paragraph (e)(5) of

this section, may have contents identification limited to a generic or

proprietary name or other proprietary identification of the carcinogen

and percent.

(ii) Containers of a carcinogen addressed by this section and

containers required under paragraphs (c)(4)(v) and (c)(6) (vii)(B), and

(viii)(B) of this section that are accessible to or handled by

employees other than authorized employees or employees trained in

accordance with paragraph (e)(5) of this section shall have contents

identification that includes the full chemical name and Chemical

Abstracts Service Registry number as listed in paragraph (a)(1) of this

section.

[[Page 9248]]

(iii) Containers shall have the warning words ``CANCER-SUSPECT

AGENT'' displayed immediately under or adjacent to the contents

identification.

(iv) Containers whose contents are carcinogens addressed by this

section with corrosive or irritating properties shall have label

statements warning of such hazards noting, if appropriate, particularly

sensitive or affected portions of the body.

(3) Lettering. Lettering on signs and instructions required by

paragraph (e)(1) shall be a minimum letter height of 2 inches (5 cm).

Labels on containers required under this section shall not be less than

one half the size of the largest lettering on the package, and not less

than 8-point type in any instance. Provided, That no such required

lettering need be more than 1 inch (2.5 cm) in height.

(4) Prohibited statements. No statement shall appear on or near any

required sign, label, or instruction that contradicts or detracts from

the effect of any required warning, information, or instruction.

(5) Training and indoctrination. (i) Each employee prior to being

authorized to enter a regulated area, shall receive a training and

indoctrination program including, but not necessarily limited to:

(A) The nature of the carcinogenic hazards of a carcinogen

addressed by this section, including local and systemic toxicity;

(B) The specific nature of the operation involving a carcinogen

addressed by this section that could result in exposure;

(C) The purpose for and application of the medical surveillance

program, including, as appropriate, methods of self-examination;

(D) The purpose for and application of decontamination practices

and purposes;

(E) The purpose for and significance of emergency practices and

procedures;

(F) The employee's specific role in emergency procedures;

(G) Specific information to aid the employee in recognition and

evaluation of conditions and situations which may result in the release

of a carcinogen addressed by this section;

(H) The purpose for and application of specific first aid

procedures and practices;

(I) A review of this section at the employee's first training and

indoctrination program and annually thereafter.

(ii) Specific emergency procedures shall be prescribed, and posted,

and employees shall be familiarized with their terms, and rehearsed in

their application.

(iii) All materials relating to the program shall be provided upon

request to authorized representatives of the Assistant Secretary and

the Director.

(f) Reports--(1) Operations. The information required in paragraphs

(f)(1) (i) through (iv) of this section shall be reported in writing to

the nearest OSHA Area Director. Any changes in such information shall

be similarly reported in writing within 15 calendar days of such

change:

(i) A brief description and in-plant location of the area(s)

regulated and the address of each regulated area;

(ii) The name(s) and other identifying information as to the

presence of a carcinogen addressed by this section in each regulated

area;

(iii) The number of employees in each regulated area, during normal

operations including maintenance activities; and

(iv) The manner in which carcinogens addressed by this section are

present in each regulated area; for example, whether it is

manufactured, processed, used, repackaged, released, stored, or

otherwise handled.

(2) Incidents. Incidents that result in the release of a carcinogen

addressed by this section into any area where employees may be

potentially exposed shall be reported in accordance with this

paragraph.

(i) A report of the occurrence of the incident and the facts

obtainable at that time including a report on any medical treatment of

affected employees shall be made within 24 hours to the nearest OSHA

Area Director.

(ii) A written report shall be filed with the nearest OSHA Area

Director within 15 calendar days thereafter and shall include:

(A) A specification of the amount of material released, the amount

of time involved, and an explanation of the procedure used in

determining this figure;

(B) A description of the area involved, and the extent of known and

possible employee exposure and area contamination;

(C) A report of any medical treatment of affected employees, and

any medical surveillance program implemented; and

(D) An analysis of the circumstances of the incident and measures

taken or to be taken, with specific completion dates, to avoid further

similar releases.

(g) Medical surveillance. At no cost to the employee, a program of

medical surveillance shall be established and implemented for employees

considered for assignment to enter regulated areas, and for authorized

employees.

(1) Examinations. (i) Before an employee is assigned to enter a

regulated area, a preassignment physical examination by a physician

shall be provided. The examination shall include the personal history

of the employee, family and occupational background, including genetic

and environmental factors.

(ii) Authorized employees shall be provided periodic physical

examinations, not less often than annually, following the preassignment

examination.

(iii) In all physical examinations, the examining physician shall

consider whether there exist conditions of increased risk, including

reduced immunological competence, those undergoing treatment with

steroids or cytotoxic agents, pregnancy, and cigarette smoking.

(2) Records. (i) Employers of employees examined pursuant to this

paragraph shall cause to be maintained complete and accurate records of

all such medical examinations. Records shall be maintained for the

duration of the employee's employment. Upon termination of the

employee's employment, including retirement or death, or in the event

that the employer ceases business without a successor, records, or

notarized true copies thereof, shall be forwarded by registered mail to

the Director.

(ii) Records required by this paragraph shall be provided upon

request to employees, designated representatives, and the Assistant

Secretary in accordance with 29 CFR 1915.1120 (a) through (e) and (g)

through (i). These records shall also be provided upon request to the

Director.

(iii) Any physician who conducts a medical examination required by

this paragraph shall furnish to the employer a statement of the

employee's suitability for employment in the specific exposure.

Secs. 1915.1004-1915.1016 [Amended]

3. In Secs. 1915.1004, 1915.1006, 1915.1007, 1915.1008, 1915.1009,

1915.1010, 1915.1011, 1915.1012, 1915.1013, 1915.1014, 1915.1015, and

1915.1016, the text is removed in its entirety and replaced with the

following text (below the section heading) in each section: ``See

Sec. 1915.1003, 13 carcinogens.''.

PART 1926--SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION

Subpart C--General Safety and Health Standards

1. The authority citation for subpart C continues to read as

follows:

[[Page 9249]]

Authority: Sec. 107, Contract Work Hours and Safety Standards

Act (40 U.S.C. 333); secs. 4, 6, and 8, Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), or 9-83 (48 FR

35736) as applicable.

2. In Sec. 1926.30, paragraph (b) is revised to read as follows:

Sec. 1926.30 Shipbuilding and ship repairing.

* * * * *

(b) Applicable safety and health standards. For the purpose of work

carried out under this section, the safety and health regulations in

part 1915 of this title, Shipyard Employment, shall apply.

Sec. 1926.31 [Amended]

3. In Sec. 1926.31(a)(1), the words ``Railway Labor Building'' are

amended to read ``Frances Perkins Building.''

4. In Sec. 1926.31(a)(2), a comma is inserted following the words

``Health Administration'' and the words ``1973-74, at page 323'' that

appear at the end of the paragraph are removed.

Sec. 1926.33 [Amended]

5. In the first sentence of Sec. 1926.33(c)(13)(i), the word

``least'' is revised to read ``latest.''

Subpart D--Occupational Health and Environmental Controls

6. The authority citation for subpart D continues to read as

follows:

Authority: Sec. 107, Contract Work Hours and Safety Standards

Act (40 U.S.C. 333); secs. 4, 6, and 8, Occupational Safety and

Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's

Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR

35736), or 1-90 (55 FR 9033), as applicable.

Sec. 1926.55 [Amended]

7. In Appendix A to Sec. 1926.55, entitled ``1970 American

Conference of Governmental Industrial Hygienists' Threshold Limit

Values of Airborne Contaminants,'' the following amendments are made to

the table of airborne contaminants for construction:

a. Remove the following substances in their entirety: Aluminum (as

Al) metal; barium sulfate; benomyl; bismuth telluride, undoped; calcium

hydroxide; calcium silicate; 2-chloro-6-(trichloromethyl) pyridine;

clopidol; dicyclopentadienyl iron; mineral wool; perlite; picloram;

piperazine dihydrochloride; propionic acid; silicon; 4,4'-thiobis (6-

tert, butyl-m-cresol); and zinc stearate.

b. For the following substances, remove the entry in the fourth

column (titled mg/m\3\ b) in its entirety: Alpha-Alumina; calcium

carbonate; cellulose; crag herbicide (Sesone); emery; fibrous glass;

glycerin (mist); graphite, synthetic; gypsum; kaolin; limestone;

magnesite; marble; pentaerythritol; plaster of Paris; Portland cement;

rouge; silicon carbide; starch; sucrose; temephos; tin oxide (as Sn);

titanium dioxide; and vegetable oil mist.

c. Entries for chlorine dioxide, methylenedianiline, and propane

and cross-references for DDT and DDVP are added (in alphabetical order)

to read as follows:

----------------------------------------------------------------------------------------------------------------

Substance CAS No.d ppm a mg/m3 b Designation

----------------------------------------------------------------------------------------------------------------

* * * * * *

*

Chlorine dioxide......................... 10049-04-4 0.1 0.3 ...........................

* * * * * *

*

DDT, see Dichlorodiphenyltrichloroethane. .............. ........... ........... ...........................

DDVP, see Dichlorvos..................... .............. ........... ........... ...........................

* * * * * *

*

Methylenedianiline (MDA)................. 101-77-9 ........... ........... ...........................

* * * * * *

*

Propane.................................. 74-98-6 E ........... ...........................

* * * * * *

*

----------------------------------------------------------------------------------------------------------------

d. In the entry for butadiene (1,3-butadiene), in the first column

(``Substance''), the superscript letter (footnote identifier) ``h'' is

removed.

e. In the entry for cadmium dust fume (as Cd), in the first column

(``Substance''), the words ``dust fume'' are removed, and in the last

three columns (for ppm, mg/m3, and skin designation) the dashes

are removed and the entries are left blank.

f. In the entry for chloroform (Trichloromethane), ``(C)'' is added

to the beginning of the entries for the third and fourth columns (for

ppm and mg/m3).

g. In the entry for coal tar pitch volatiles * * *, the entry for

the second column, CAS No., is amended to read ``65996-93-2''.

h. Under the substance coke oven emissions, all the entries in the

second through fifth columns are removed and left blank.

i. In the entry for cyanides (as CN), the dash in the last column

(for skin designation) is removed and a capital letter ``X'' is

inserted in its place.

j. In the entry for 1,2-Dibromo-3-chloropropane (CBCP), the

parenthetical substance name in the first column is corrected to read

``(DBCP)''; the dash entry in the fourth column (for mg/m3) is

removed and left blank; and in the last column (for skin designation),

a dash is added.

k. In the entry for 2-Diethylaminoethanol, the dash in the last

column (for skin designation) is removed and a capital letter ``X'' is

inserted in its place.

l. In the entry for hydrogen selenide (as Se), ``0.2'' is added

under the fourth column (for mg/m3), and a dash is added in the

last column (for skin designation).

m. For the entry ``lead, inorganic (as Pb),'' in the first column

for that substance, a semi-colon followed by the words ``see 1926.62''

is added, and the entries in the third through fifth columns (for ppm,

mg/m3, and skin designation) are removed and left blank.

n. In the subentry row ``Total particulate'' for magnesium oxide

fume, the entry ``15'' from the fourth column headed ``(mg/m3)''

is transposed with the dash entry in the third column headed ``(ppm).''

o. In the entry methylene chloride, in the first column, the words

``h; see 56 FR 57036'' are removed.

p. In the entry for methyl methacrylate, the entry ``100'' in the

last column (for skin designation) is removed and a dash is inserted in

its place.

q. In the entry for methyl silicate, ``(C)'' is added to the

beginning of the entries for the third and fourth columns (for ppm and

mg/m\3\).

r. In the entries for parathion and picric acid, the dash in the

last column (for skin designation) is removed and a capital letter

``X'' is inserted in its place.

s. In the subentry row ``Total dust'' for Portland cement, the

entry ``15'' from the third column headed ``(ppm)'' is

[[Page 9250]]

transposed with the dash entry in the fourth column headed ``(mg/

m\3\)'', and the entry ``10'' in the last column (for skin designation)

is removed and a dash is inserted in its place.

t. In the entry for rouge, the dash entry in the third column (for

ppm) is removed and left blank.

u. Under the entry for silicates (less than 1% crystalline silica),

the dash entries in the second column for the subentries ``soapstone,

total dust'' and ``soapstone, respirable dust'' for CAS No. are removed

and left blank.

v. Under the entry for silicates (less than 1% crystalline silica),

for the subentry ``talc (containing asbestos),'' in the first column

for that substance, a semi-colon followed by the words ``use asbestos

limit; see 1926.58'' is added; in addition, the entries in the second

through fifth columns are removed and left blank.

w. Under the entry for silicates (less than 1% crystalline silica),

for the subentry ``tremolite,'' in the first column for that substance,

a comma followed by the words ``asbestiform; see 1926.58'' is added to

the entry; in addition, the entries in the third through fifth columns

are removed and left blank.

x. In the entry for styrene, ``(C)'' is added to the beginning of

the entries for the third and fourth columns (for ppm and mg/m\3\), and

the entry ``50'' in the last column (for skin designation) is removed

and a dash is inserted in its place.

y. In the entry for toluene, the entry ``100'' in the last column

(for skin designation) is removed and a dash is inserted in its place.

z. In the entry for trimethyl benzene, a dash is inserted in the

last column (for skin designation).

aa. In the entry for 2,4,6-Trinitrophenyl, the substance name in

the first column is corrected to read ``2,4,6-Trinitrophenol''.

bb. In the list entitled ``Mineral Dusts'' that appears at the end

of the table (immediately preceding the footnotes to the table), the

following parenthetical is added in brackets at the end of the entry

for the substance ``Inert or Nuisance Particulates: (m)'': ``[*

Inert or Nuisance Dusts includes all mineral, inorganic, and organic

dusts as indicated by examples in TLV's Appendix D]''.

cc. Footnote h, which appears at the end of the table, is removed.

Sec. 1926.57 [Amended]

8. In Sec. 1926.57(f)(8), the designation ``(i)'' that appears at

the beginning of the first sentence is removed.

9. In Sec. 1926.57(g)(5)(vii), the words ``figure D-57.1'' at the

end of the first sentence are revised to read ``Figure D-57.6''.

10. In Sec. 1926.57(g)(5)(viii), the words ``figure D-57.2'' at the

end of the first sentence are revised to read ``Figure D 57.7''.

11. In Sec. 1926.57(g)(5)(x), the words ``figure D-57.3'' at the

end of the last sentence are revised to read ``Figure D-57.8''.

12. In Sec. 1926.57(g)(5), the illustrations are amended as

follows:

a. The caption ``Figure D-57.1--Vertical Spindle Disc Grinder

Exhaust Hood and Branch Pipe Connections'' is added below the

illustration that immediately follows Sec. 1926.57(g)(5)(x).

b. The caption ``Figure D-57.2--Standard Grinder Hood'' is added

below the second illustration following Sec. 1926.57(g)(5)(x)

(preceding the table on wheel dimensions).

c. The caption ``Figure D-57.3--A Method of Applying an Exhaust

Enclosure to Swing-Frame Grinders'' and the words ``Note: Baffle to

reduce front opening as much as possible'' are added below the third

illustration.

d. The caption ``Figure D-57.4'' is added below the fourth

illustration (preceding the table on Standard Buffing and Polishing

Hood).

e. Below the fifth illustration that precedes Table D-57.12, the

caption ``Figure D-57.5--Cradle Polishing or Grinding Enclosure'' and

the words ``Entry loss = 0.45 velocity pressure for tapered takeoff''

are added.

f. Table D-57.12, entitled ``Maximum Allowable Size of Containers

and Portable Tanks'' is removed.

g. Immediately below the sixth illustration, preceding the table,

the caption ``Figure D-57.6--Horizontal Single-Spindle Disc Grinder

Exhaust Hood and Branch Pipe Connections'' is added.

h. Below the illustration that follows newly designated Figure D-

57.6 and precedes the table, the caption ``Figure D-57.7--Horizontal

Double-Spindle Disc Grinder Exhaust Hood and Branch Pipe Connections''

is added.

i. In the caption for the illustration that appears before the

table on Belt width, number ``Figure D-57.3'' is revised to read

``Figure D-57.8'' and the words ``Entry loss = 0.45 velocity pressure

for tapered takeoff'' are added immediately below that caption.

13. In Sec. 1926.57(i)(2)(i), the reference ``D-57.4'' is revised

to read ``D-4''.

14. In Table D-57.12, which appears following

Sec. 1926.57(i)(4)(iii)(A)(2), footnote 2 is amended by revising ``he''

to read ``the''.

Subpart E--Personal Protective and Life Saving Equipment

15. The authority citation for subpart E is revised to read as

follows:

Authority: Sec. 107, Contract Work Hours and Safety Standards

Act (Construction Safety Act) (40 U.S.C. 333); Secs. 4, 6 and 8,

Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655,

657); Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR

25059), 9-83 (48 FR 35736), or 1-90 (55 FR 9033), as applicable; and

29 CFR part 1911.

Sec. 1926.103 [Amended]

16. In Sec. 1926.103(a)(2), the phrase ``approved by the U.S.

Bureau of Mines'' is revised to read ``approved by the Mine Safety and

Health Administration a

This text is long and has been trimmed here. Open the source document for the complete record.