Notice of Receipt of Petition for Decision That Nonconforming 1997 Mercedes-Benz Gelaendewagen Type 463 Multi-Purpose Passenger Vehicles are Eligible for Importation

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. 96-106; Notice 1]

Notice of Receipt of Petition for Decision That Nonconforming

1997 Mercedes-Benz Gelaendewagen Type 463 Multi-Purpose Passenger

Vehicles are Eligible for Importation

AGENCY: National Highway Traffic Safety Administration, DOT.

ACTION: Request for comments on petition for decision that

nonconforming 1997 Mercedes-Benz Gelaendewagen Type 463 multi-purpose

passenger vehicles (MPVs) are eligible for importation.

-----------------------------------------------------------------------

SUMMARY: This notice requests comments on a petition submitted to the

National Highway Traffic Safety Administration (NHTSA) for a decision

that a 1997 Mercedes-Benz Gelaendewagen Type 463 MPV that was not

originally manufactured to comply with all applicable Federal motor

vehicle safety standards is eligible for importation into the United

States because it has safety features that comply with, or are capable

of being altered to comply with, all such standards.

DATES: The closing date for comments on the petition is November 8,

1996.

ADDRESSES: Comments should refer to the docket number and notice

number, and be submitted to: Docket Section, Room 5109, National

Highway Traffic Safety Administration, 400 Seventh St., SW.,

Washington, DC 20590. [Docket hours are from 9:30 am to 4 pm.]

FOR FURTHER INFORMATION CONTACT: George Entwistle, Office of Vehicle

Safety Compliance, NHTSA (202-366-5306).

SUPPLEMENTARY INFORMATION:

Background

Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not

originally manufactured to conform to all

[[Page 52991]]

applicable Federal motor vehicle safety standards shall be refused

admission into the United States unless NHTSA has decided that the

motor vehicle is substantially similar to a motor vehicle originally

manufactured for importation into and sale in the United States,

certified under 49 U.S.C. Sec. 30115, and of the same model year as the

model of the motor vehicle to be compared, and is capable of being

readily altered to conform to all applicable Federal motor vehicle

safety standards. Where there is no substantially similar U.S.-

certified motor vehicle, 49 U.S.C. 30141(a)(1)(B) permits a

nonconforming motor vehicle to be admitted into the United States if

its safety features comply with, or are capable of being altered to

comply with, all applicable Federal motor vehicle safety standards

based on destructive test data or such other evidence as NHTSA decides

to be adequate.

Petitions for eligibility decisions may be submitted by either

manufacturers or importers who have registered with NHTSA pursuant to

49 CFR Part 592. As specified in 49 CFR 593.7, NHTSA publishes notice

in the Federal Register of each petition that it receives, and affords

interested persons an opportunity to comment on the petition. At the

close of the comment period, NHTSA decides, on the basis of the

petition and any comments that it has received, whether the vehicle is

eligible for importation. The agency then publishes this decision in

the Federal Register.

Europa International, Inc. of Santa Fe, New Mexico (Registered

Importer No. R-91-002) has petitioned NHTSA to decide whether 1997

Mercedes-Benz Gelaendewagen Type 463 MPVs are eligible for importation

into the United States. Europa contends that this vehicle is eligible

for importation under 49 U.S.C. Sec. 30141(a)(1)(B) because it has

safety features that comply with, or are capable of being altered to

comply with, all applicable Federal motor vehicle safety standards.

Specifically, the petitioner claims that the 1997 Mercedes-Benz

Gelaendewagen Type 463 MPV has safety features that comply with

Standard Nos. 102 Transmission Shift Lever Sequence * * * (based on

visual inspection and operation), 103 Defrosting and Defogging Systems

(based on visual inspection), 104 Windshield Wiping and Washing Systems

(based on operation), 113 Hood Latch Systems (based on information in

owner's manual describing operation of secondary latch mechanism), 116

Brake Fluids (based on visual inspection of certification markings and

information in owner's manual describing fluids installed at factory),

119 New Pneumatic Tires for Vehicles other than Passenger Cars (based

on visual inspection of certification markings), 124 Accelerator

Control Systems (based on operation and comparison to U.S.-certified

vehicles), 201 Occupant Protection in Interior Impact (based on test

data and certification of vehicle to European standard), 202 Head

Restraints (based on Standard No. 208 test data for prior model year

vehicle with same head restraint and certification of vehicle to

European standard), 204 Steering Control Rearward Displacement (based

on test film for prior model year vehicle), 205 Glazing Materials

(based on visual inspection of certification markings), 207 Seating

Systems, (based on test results and certification of vehicle to

European standard), 209 Seat Belt Assemblies (based on wiring diagram

of seat belt warning system and visual inspection of certification

markings), 211 Wheel Nuts, Wheel Discs and Hubcaps (based on visual

inspection), 214 Side Impact Protection (based on test results for

prior model year vehicle), and 219 Windshield Zone Intrusion (based on

test results and certification information for prior model year

vehicle).

The petitioner also contends that the 1997 Mercedes-Benz

Gelaendewagen Type 463 MPV is capable of being altered to comply with

the following standards, in the manner indicated:

Standard No. 101 Controls and Displays: (a) Substitution of a lens

marked ``Brake'' for a lens with an ECE symbol on the brake failure

indicator lamp; (b) installation of a speedometer/odometer calibrated

in miles per hour.

Standard No. 108 Lamps, Reflective Devices and Associated

Equipment: (a) Installation of U.S.-model sealed beam headlamps; (b)

installation of U.S.-model side marker lamps and reflectors; (c)

installation of a high mounted stop lamp. The petitioner asserts that

testing performed on the taillamp reveals that it complies with the

standard, even though it lacks a DOT certification marking, and that

all other lights are DOT certified.

Standard No. 111 Rearview Mirrors: Inscription of the required

warning statement on the convex surface of the passenger side rearview

mirror.

Standard No. 114 Theft Protection: Installation of a warning buzzer

in the steering lock electrical circuit.

Standard No. 118 Power-Operated Window Systems: rewiring of the

power window system so that the window transport is inoperative when

the front doors are open.

Standard No. 120 Tire Selection and Rims for Vehicles other than

Passenger Cars: Installation of a tire information placard. The

petitioner asserts that even though the tire rims lack a DOT

certification marking, they comply with the standard, based on their

manufacturer's certification that they comply with the German TUV

regulations, as well as their certification by the British Standards

Association and the Rim Association of Australia.

Standard No. 206 Door Locks and Door Retention Components:

Installation of interior locking buttons on all door locks and

modification of rear door locks to disable latch release controls when

locking mechanism is engaged.

Standard No. 208 Occupant Crash Protection: (a) Installation of

complying driver's and passenger's side air bag systems; (b)

installation of a seat belt warning system; (c) placement of an air bag

warning label on the visors of vehicles manufactured after November

1996. The petitioner states that the vehicle will meet frontal impact

test requirements with structural modifications described in a

submission that has been granted confidentiality by NHTSA's Office of

Chief Counsel under 49 CFR Part 512.

Standard No. 210 Seat Belt Assembly Anchorages: Insertion of

instructions on the installation and use of child restraints in the

owner's manual for the vehicle. The petitioner certifies that the

vehicle complies with this standard on the basis of tests performed to

the standard's requirements by an independent testing and engineering

laboratory.

Standard No. 212 Windshield Retention: Application of cement to the

windshield's edges.

Standard No. 301 Fuel System Integrity: Installation of a rollover

valve.

Standard No. 302 Flammability of Interior Materials: Treatment of

fabric seating surfaces with a flame-proof spray.

The petitioner additionally states that a vehicle identification

number (VIN) plate must be attached to the vehicle's dash so that it is

visible to an observer at the driver's side ``A'' pillar, as required

by 49 CFR Part 565. The petitioner also states that a vehicle rollover

warning statement must be inserted in the owner's manual and on a

sticker affixed to the driver's side visor of short wheelbase

Gelaendewagens, as required by 49 CFR 575.105.

Interested persons are invited to submit comments on the petition

described above. Comments should refer to the docket number and be

submitted to: Docket Section, National Highway Traffic Safety

Administration, Room 5109, 400 Seventh Street, S.W.,

[[Page 52992]]

Washington, DC 20590. It is requested but not required that 10 copies

be submitted.

All comments received before the close of business on the closing

date indicated above will be considered, and will be available for

examination in the docket at the above address both before and after

that date. To the extent possible, comments filed after the closing

date will also be considered. Notice of final action will be published

in the Federal Register pursuant to the authority indicated below.

Authority: 49 U.S.C. 30141(a)(1)(B) and (b)(1); 49 CFR 593.8;

delegations of authority at 49 CFR 1.50 and 501.8.

Issued on October 3, 1996.

Marilynne Jacobs,

Director, Office of Vehicle Safety Compliance.

[FR Doc. 96-25883 Filed 10-8-96; 8:45 am]

BILLING CODE 4910-59-P