Proposed Revision of Federal Information Processing Standard (FIPS) 177, Initial Graphics Exchange Specification (IGES)

Federal RegisterApr 12, 1995

Ask Donna

What actually matters in this document.

Text

DEPARTMENT OF COMMERCE

National Institute of Standards and Technology

[Docket No. 950317077-5077-01]

RIN 0693-AB13

Proposed Revision of Federal Information Processing Standard

(FIPS) 177, Initial Graphics Exchange Specification (IGES)

agency: National Institute of Standards and Technology (NIST),

Commerce.

action: Notice; Request for comments.

-----------------------------------------------------------------------

sumamry: NIST is prosing a revision of FIPS PUB 117, Initial Graphics

Exchange Specification (IGES). IGES defines a neutral file format for

the exchange of product model data and representation among differing

computer-aided design and computer-aided manufacturing (CA/CAM)

systems. This proposed revision will provided increased clarification

and enhancement of the existing standard, and added conformance

requirements and application protocols (APs) specified within the

American National Standard Digital Representation for

[[Page 18584]] Communication of Product Definition Data, ANSI/US PRO/

IPO (United States Product Data Association/IGES PDES Organization--

100-1993, Version 5.2.

Prior to the submission of this proposed revision to FIPS 177 to

the Secretary of Commerce for review and approval, it is essential to

assure that consideration is given to the needs and views of

manufacturers, the public, and State and local governments. The purpose

of this notice is to solicit such views.

This proposed revision contains two sections: (1) An announcement

section, which provides information concerning the applicability,

implementation, and maintenance of the standard; and (2) a

specifications section. Only the announcement section of the standard

is provided in this notice. Interested parties may obtain copies of the

ANSI/US PRO/IPO-1993 and the specified application protocols (Layered

Electrical Product (LEP) Application Protocol; 3-D Piping Application

Protocol; and Engineering Drawing (Class II) Subset (MIL-D-28000A))

from the National Computer Graphics Association, 2722 Merrilee Drive,

Suite 200, Fairfax, VA, 22031, telephone: (703) 698-9600.

dates: Comments on this proposed revision must be received on or before

July 11, 1995.

addresses: Written comments concerning the adoption of this proposed

revision should be sent to: Director, Computer Systems Laboratory,

ATTN: Proposed Revision of FIPS 177, IGES, Technology Building, Room

B154, National Institute of Standards and Technology, Gaithersburg, MD

20899.

Written comments received in response to this notice will be made

part of the public record and will be made available for inspection and

copying in the Central Reference and Records Inspection Facility, Room

6020, Herbert C. Hoover Building, 14th Street between Pennsylvania and

Constitution Avenues, NW., Washington, DC 20230.

for further information contact: Ms. Lynne Rosenthal, National

Institute of Standards and Technology, Gaithersburg, MD 20899,

telephone (301) 975-3353.

Executive Order 12866

This FIPS notice has been determined to be ``not significant'' for

purposes of E.O. 12866.

Dated: April 4, 1995.

Samuel Kramer,

Associate Director.

Proposed Federal Information Processing Standards Publication 177-1

(Date)

Announcing the Standard for Initial Graphics Exchange Specification

(IGES)

Federal Information Processing Standards Publications (FIPS PUBS)

are issued by the National Institute of Standards and Technology (NIST)

after approval by the Secretary of Commerce pursuant to Section 111(d)

of the Federal Property and Administrative Services Act of 1949 as

amended by the Computer Security Act of 1987, Public Law 100-235.

1. Name of Standard. Initial Graphics Exchange Specification (IGES)

FIPS PUB 177-1).

2. Category of Standard. Software Standard; Graphics and

Information Interchange.

3. Explanation. This publication is a revision of the FIPS PUB 177

and supersedes FIPS PUB 177 in its entirety. It provides a substantial,

upward-compatible enhancement of IGES Version 4.0. FIPS PUB 177-1

specifies new conformance requirements, the addition and use of

application protocols (APs), and increased enhancement, correction, and

clarification of the existing specification. It does not contain any

new requirements that would make an existing conforming implementation

nonconforming.

FIPS PUB 177-1 adopts the American National Standard Digital

Representation for Communication of Product Definition Data, ANSI/US

PRO/IPO (United States Product Data Association/IGES PDES

Organization)-100-1993, Version 5.2, and the specified application

protocols. FIPS PUB 177-1 addresses IGES implementation and data file

acquisition, interpretation, and conformance.

The purpose of the FIPS for IGES is to enable the compatible

exchange of product definition data used by dissimilar computer-aided

design and computer-aided manufacturing (CAD/CAM) systems. Utilizing a

neutral database format the IGES processor can create or translate two-

dimensional (2-D) or three-dimensional (3-D) vector-based digital

product model data. The standard specifies file structure and

syntactical definition, and defines the representation of geometric,

topological, and nongeometric product definition data. The exact

specification is in Section 10 of this standard.

4. Approving Authority. Secretary of Commerce.

5. Maintenance Agency. U.S. Department of Commerce, National

Institute of Standards and Technology (NIST), Computer Systems

Laboratory (CSL).

6. Cross Index.

a. American National Standard Digital Representation for

Communication of Product Definition Data, ANSI/US PRO/IPO-100-1993,

Version 5.2.

b. American Society of Mechanical Engineers/American National

Standards Institute (ASME/ANSI) Y14.26M-1989, Digital Representation

for Communication of Product Definition Data, IGES Version 4.0.

c. MIL-D-280000A, Continuous Acquisition and Life-Cycle Support

Specification, Digital Representation for Communication of Product

Definition Data: IGES Application Subsets and IGES Application

Protocols, February 10, 1992.

d. American national Standard, 3-D Piping IGES Application

Protocol, ANSI/US PRO/IPO-110-1994.

e. IGES Layered Electrical Product Application Protocol, Committee

Draft SAND94-2375, December 1, 1994.

7. Related Documents.

a. Federal Information Resources Management Regulations (FIRMR)

subpart 201.20.303, Standards, and subpart 201.39.1002, Federal

Standards.

b. Federal ADP and Telecommunications Standards Index, U.S. General

Services Administration, Information Technology Management Service,

October 1994 (updated periodically).

c. FIPS PUB 29-3, Interpretation Procedures for Federal Information

Processing Standards for Software.

d. NISTIR 4379, IGES Technical Illustrations Application Guide.

e. NISTIR 4600, IGES 5.0 Recommended Practices Guide.

f. NISTIR 5541, Initial Graphics Exchange Specification (IGES):

Procedures for the NIST IGES Validation Test Service.

g. MIL-T-31000, General Specification for Technical Data Packages.

8. Objectives. Federal standards for electronic interchange permit

Federal departments and agencies to exercise more effective control

over the production, management, and use of the government's

information resources. The primary objectives specific to IGES are to:

--Reduce the overall life-cycle cost for digital systems by

establishing a [[Page 18585]] common exchange format that allows for

the transfer of product definition data across organizational

boundaries and independent of any particular CAD/CAM system.

--Exchange digital representations of product definition data in

various forms: illustrations, 2-D drawings, 3-D edge-vertex models,

surface models, solid models, and complete product models.

--Provide CAD/CAM implementation manufacturers with a guideline for

identifying useful combinations of product definition data capabilities

in any CAD/CAM system.

--Specify Application Protocols that can be used by Federal departments

and agencies to support the exchange of product data when applicable.

9. Applicability.

9.1 This FIPS for IGES is intended for the computer-interpretable

representation and exchange of CAD/CAM product definition data among

applications and programs that are either developed or acquired for

government use. Each CAD/CAM system acquired or developed by a Federal

agency shall include an IGES preprocessor and IGES postprocessor

capability. FIPS for IGES is designed to support the exchange of 2-D or

3-D product definition data with rich attribute information. It

provides a data format for describing product design and manufacturing

information that has been created and stored in a computer-readable,

device independent form.

9.2 The FIPS for IGES shall be used when one or more of the

following situations exist:

--The product definition application or program is under constant

review, and changes may result frequently.

--It is anticipated that the life of the data files will be longer than

the life of the presently utilized CAD/CAM system.

--The application is being designed centrally for a decentralized

system that may employ computers of different makes and models and

different CAD/CAM devices.

--The product definition application may run on equipment other than

that on which it was developed.

--The product definition data is to be used and maintained by other

than the original designer.

--The product definition data is or is likely to be used by

organizations outside the Federal Government.

--It is desired to have the design understood by multiple people,

groups, or organizations.

9.3 For layered electrical product technology, three dimensional

piping, and engineering drawing applications, the use of the

appropriate application protocol or subset (as described below) is

required for implementation of this FIPS IGES.

An AP or subset provides a means to improve the fidelity of the

product data exchanged. APs are developed by domain experts for the

purpose of defining the processes, information flows, and functional

requirements of an application. An AP defines the scope, context,

information requirements, representation of the application

information, and conformance requirements. Initial release of this FIPS

for IGES publication includes two application protocols and one

application subset.

--Layered Electrical Product (LEP) Application Protocol: The LEP AP is

used for the transference of 2-D electrical and electro-mechanical

product models. This AP is required for layered electrical products

technology applications, including specification control drawings,

circuitry, fabrication and final assembly of a layered product system.

--3-D Piping Application Protocol: The 3-D Piping AP is used for the

exchange of models from one piping modeling application to another.

This AP is required for 3-D piping and related equipment models,

including the fabrication and assembly of piping systems (e.g. pipe,

pipe fittings, attached equipment, piping supports, and insulation).

--Engineering Drawing (Class II) Subset (MIL-D-28000A): The Class II

subset is used for exchange of the drawing model; including geometric

and annotation entities, attributes such as color and line fonts, and

organization information such as levels and subfigures. This subset is

required for the exchange of engineering drawings and product data

following MIL-T-31000 (General Specification for Technical Data

Packages).

10. Specifications. This FIPS adopts ANSI/US PRO/IPO-100-1993 and

the specified application protocols: Layered Electrical Product (LEP)

Application Protocol; 3-D Piping Application Protocol; and Engineering

Drawing (Class II) Subset (MIL-D-28000A). The ANSI/US PRO/IPO-100-1993

standard for IGES, defines the communications file structure and format

(i.e., a file of entities), language format, and the representation of

product definition data.

New entities and constructs are added with each revision and are

upwardly compatible. Thus, a processor conforming to IGES Version 5.2

would be able to read and process an IGES Version 4.0 file, but the

converse may not be true. The capabilities brought to the IGES user

implementing the IGES Version 5.2 standard are:

--A new character set for the European Community;

--Additional properties to the attribute table for Architecture/

Engineering/Construction (AEC);

--The addition of a new form of the drawing entity; and

--The addition of a new class of entity use, termed construction

information.

Conformance Requirements. Conformance is mandatory for this

standard and is applicable to all Federal department and agency

procurements. Conforming data files and processors must adhere to all

the rules appropriate to specific features, such as entities, defined

within ANSI/US PRO/IPO-100-1993 and any of the specified application

protocols. Vendors of processors claiming conformance to this standard

shall complete documentation which accurately indicates the processor's

support of, and mapping between, native and IGES entities.

A conforming preprocessor shall create conforming IGES data files

which represent the native database which was input to the

preprocessor. File content shall represent the native entities

according to the vendor's completed documentation. It is desirable and

recommended that the preprocessor report on any native feature or

entity which has not been written to the IGES data file.

A conforming postprocessor shall translate conforming IGES data

files into the native database form of a specific CAD/CAM system. It

shall convert each supported entity into native constructs, which

preserve the functionality and match the geometry, attributes, and

relationships of the IGES entity in the file. It is desirable and

recommended that the postprocessor report on any IGES entities or

features which have been discarded.

Any visual presentation produced by the processor shall accurately

and correctly represent the IGES constructs contained in the data file

and specified by ANSI/US PRO/IPO-100-1993 and, if applicable, the AP or

subset. For example, the display of a design which is filled with a

pattern of lines as indicated by the pattern code of the Sectioned Area

Entity (type 230) shall resemble the predefined definitions illustrated

in the ANSI/US PRO/IPO-100-1993 specification.

Conformance Rules for Application Protocols and Subsets. An

application protocol or subset which claims [[Page 18586]] conformance

to this standard, must satisfy the following rule:

--An implementation conforming to an AP shall satisfy the conformance

requirements specified in the AP as well as the conformance

requirements in the ANSI/US PRO/IPO-100-1993 specification.

11. Implementation. The implementation of this standard involves

four areas of consideration: effective date, acquisition,

interpretation, and validation.

11.1 Effective Date. This publication is effective six (6) months

after date of publication upon final announcement in the Federal

Register. A transition period of twelve (12) months, beginning on the

effective date, allows industry to produce IGES implementations and

data files conforming to this is standard. Agencies are encouraged to

use this standard for solicitation proposals during the transition

period. This standard is mandatory for use in all solicitation

proposals for IGES data files and implementations (i.e., computer-aided

design and manufacturing systems) acquired twelve (12) months after the

effective date.

11.2 Acquisition of IGES Implementations and Data Files.

Conformance to this standard should be considered whether the CAD/CAM

systems are developed internally, acquired as part of a system

procurement, acquired by separate procurement, used under a leasing

agreement, or specified for use in contracts for programming services.

Recommended terminology for procurement of FIPS IGES is contained in

the U.S. General Services Administration publication Federal ADP and

Telecommunications Standards Index, Chapter 5, Part 1.

11.3 Interpretation FIPS IGES. Resolutions of questions regarding

this standard will be provided by NIST. Procedures for interpretations

are specified in FIPS PUB 29-3. All questions concerning the

specifications and content should be addressed to: Director, Computer

Systems Laboratory, ATTN: FIPS IGES Interpretation, National Institute

of Standards and Technology, Gaithersburg, MD 20899.

11.4 Validation of IGES Implementations. Implementations of FIPS

for IGES shall be validated in accordance with the NIST Computer

Systems Laboratory (CSL) validation procedures for FIPS for IGES,

NISTIR 5541, Procedures for the NIST IGES Validation Test Service.

Recommended procurement terminology for validation of FIPS for IGES is

contained in the U.S. General Services Administration publication

Federal ADP and Telecommunications Standards Index, Chapter 5, Part 2.

This GSA publication provides terminology for three validation options:

Delayed Validation, Prior Validation Testing, and Prior Validation. The

agency shall select the appropriate validation option and shall specify

appropriate time frames for validation and correction of

nonconformities. The agency is advised to refer to the NIST publication

Validated Products List for information about the validation status of

IGES products. This information may be used to specify validation time

frames that are not unduly restrictive of competition.

Implementations shall be evaluated using the NIST IGES Test Suite.

The NIST IGES Test Suite was first released in October 1994 to assist

users and vendors determine compliance with FIPS PUB 177 and/or MIL-D-

28000, Class II subset. The results of validation testing by the NIST

IGES Validation Test Service are published on a quarterly basis in the

Validated Products List, available from the National Technical

Information Service (NTIS).

Current information about the NIST IGES Validation Test Service and

validation procedures for FIPS for IGES is available from: National

Institute of Standards and Technology, Computer Systems Laboratory,

Graphics Software Group, IGES Test Service, Building 225, Room A266,

Gaithersburg, MD 20899, (301) 975-3265.

12. Waivers.

Under certain exceptional circumstances, the heads of Federal

departments and agencies may approve waivers to Federal Information

Processing Standards (FIPS). The head of such agency may redelegate

such authority only to a senior official designated pursuant to section

3506(b) of Title 44, U.S. Code. Waivers shall be granted only when:

a. Compliance with a standard would adversely affect the

accomplishment of the mission of an operator of a Federal computer

system, or

b. Cause a major adverse financial impact on the operator which is

not offset by Governmentwide savings.

Agency heads may act upon a written waiver request containing the

information detailed above. Agency heads may also act without a written

waiver request when they determine that conditions for meeting the

standard cannot be met. Agency heads may approve waivers only by a

written decision which explains the basis on which the agency head made

the required finding(s). A copy of each such decision, with procurement

sensitive or classified portions clearly identified, shall be sent to:

National Institute of Standards and Technology; Attn: FIPS Waiver

Decisions, Technology Building, Room B-154; Gaithersburg, MD 20899.

In addition, notice of each waiver granted and each delegation of

authority to approve waivers shall be sent promptly to the Committee on

Government Operations of the House of Representatives and the Committee

on Governmental Affairs of the Senate and shall be published promptly

in the Federal Register.

When the determination on a waiver applies to the procurement of

equipment and/or services, a notice of the waiver determination must be

published in the Commerce Business Daily as a part of the notice of

solicitation for offers of an acquisition or, if the waiver

determination is made after that notice is published, by amendment to

such notice.

A copy of the waiver, any supporting documents, the document

approving the waiver and any supporting and accompanying documents,

with such deletions as the agency is authorized and decides to make

under 5 U.S.C. Sec. 552(b), shall be part of the procurement

documentation and retained by the agency.

[FR Doc. 95-9007 Filed 4-11-95; 8:45 am]

BILLING CODE 3510-CN-M

This is a copy of a public record, reproduced as it was published. It is not legal advice, and it may not be the version a court would rely on. Check the official source before you cite it.

A word about cookies

We need a few to keep you signed in and the library working. The rest help us see which pages people use and where they get stuck. They stay off unless you say yes.