Notice of Receipt of Petition for Decision That Nonconforming Model Year 2008-2011 Ferrari 599 Passenger Cars Are Eligible for Importation

DEPARTMENT OF TRANSPORTATION

National Highway Traffic Safety Administration

[Docket No. NHTSA-2016-0055; Notice 1]

Notice of Receipt of Petition for Decision That Nonconforming Model Year 2008-2011 Ferrari 599 Passenger Cars Are Eligible for Importation

AGENCY:

National Highway Traffic Safety Administration, DOT.

ACTION:

Receipt of petition.

SUMMARY:

This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that model year (MY) 2008-2011 Ferrari 599 passenger cars (PC) that were not originally manufactured to comply with all applicable Federal motor vehicle safety standards (FMVSS), are eligible for importation into the United States because they are substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards (the U.S.-certified version of the 2008-2011 Ferrari 599 PC) and they are capable of being readily altered to conform to the standards.

DATES:

The closing date for comments on the petition is August 22, 2016.

ADDRESSES:

Comments should refer to the docket and notice numbers above and be submitted by any of the following methods:

•

Federal eRulemaking Portal:

Go to

http://www.regulations.gov.

Follow the online instructions for submitting comments.

•

Mail:

Docket Management Facility: U.S. Department of Transportation, 1200 New Jersey Avenue SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-0001.

•

Hand Delivery or Courier:

West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., between 9 a.m. and 5 p.m. ET, Monday through Friday, except Federal holidays.

•

Fax:

202-493-2251.

Instructions:

Comments must be written in the English language, and be no greater than 15 pages in length, although there is no limit to the length of necessary attachments to the comments. If comments are submitted in hard copy form, please ensure that two copies are provided. If you wish to receive confirmation that your comments were received, please enclose a stamped, self-addressed postcard with the comments. Note that all comments

received will be posted without change to

http://www.regulations.gov,

including any personal information provided. Please see the Privacy Act heading below.

Privacy Act:

Anyone is able to search the electronic form of all comments received into any of our dockets by the name of the individual submitting the comment (or signing the comment, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the

Federal Register

published on April 11, 2000 (65 FR 19477-78).

How to Read Comments submitted to the Docket:

You may read the comments received by Docket Management at the address and times given above. You may also view the documents from the Internet at

http://www.regulations.gov.

Follow the online instructions for accessing the dockets. The docket ID number and title of this notice are shown at the heading of this document notice. Please note that even after the comment closing date, we will continue to file relevant information in the Docket as it becomes available. Further, some people may submit late comments. Accordingly, we recommend that you periodically search the Docket for new material.

FOR FURTHER INFORMATION CONTACT:

George Stevens, Office of Vehicle Safety Compliance, NHTSA (202-366-5308).

SUPPLEMENTARY INFORMATION:

Background

Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not originally manufactured to conform to all applicable FMVSS shall be refused admission into the United States unless NHTSA has decided that the motor vehicle is substantially similar to a motor vehicle originally manufactured for importation into and sale in the United States, certified under 49 U.S.C. 30115, and of the same model year as the model of the motor vehicle to be compared, and is capable of being readily altered to conform to all applicable FMVSS.

Petitions for eligibility decisions may be submitted by either manufacturers or importers who have registered with NHTSA pursuant to 49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice in the

Federal Register

of each petition that it receives, and affords interested persons an opportunity to comment on the petition. At the close of the comment period, NHTSA decides, on the basis of the petition and any comments that it has received, whether the vehicle is eligible for importation. The agency then publishes this decision in the

Federal Register

.

J.K. Technologies (JK), Inc. of Baltimore, MD (Registered Importer R-90-006) has petitioned NHTSA to decide whether nonconforming 2008-2011 Ferrari 599 PC's are eligible for importation into the United States. The vehicles which JK believes are substantially similar are MY 2008-2011 Ferrari 599 PC's sold in the United States and certified by their manufacturer as conforming to all applicable FMVSS.

The petitioner claims that it compared non-U.S. certified MY 2008-2011 Ferrari 599 PC's to their U.S.-certified counterparts, and found the vehicles to be substantially similar with respect to compliance with most FMVSS.

JK submitted information with its petition intended to demonstrate that non-U.S. certified MY 2008-2011 Ferrari 599 PC's, as originally manufactured, conform to many applicable FMVSS in the same manner as their U.S.-certified counterparts, or are capable of being readily altered to conform to those standards. Specifically, the petitioner claims that the non U.S.-certified MY 2008-2011 Ferrari 599 PC's, as originally manufactured, conform to: Standard Nos. 102

Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect,

103

Windshield Defrosting and Defogging Systems,

104

Windshield Wiping and Washing Systems,

106

Brake Hoses,

109

New pneumatic and certain specialty tires,

113

Hood Latch System,

116

Motor Vehicle Brake Fluids,

124

Accelerator Control Systems,

126

Electronic Stability Control Systems,

135

Light vehicle brake systems,

201

Occupant Protection in Interior Impact,

202a

Head Restraints,

203

Impact protection for the driver from the steering control system,

204

Steering Control Rearward Displacement,

205

Glazing Materials,

206

Door Locks and Door Retention Components,

210

Seat Belt Assembly Anchorages,

212

Windshield Mounting,

213

Child restraint systems,

214

Side Impact Protection,

216

Roof Crush Resistance,

219

Windshield Zone Intrusion,

and 302

Flammability of Interior Materials.

The petitioner also contends that the subject non-U.S certified vehicles are capable of being readily altered to meet the following standards, in the manner indicated:

Standard No. 101

Controls and Displays:

Replacement of the instrument cluster with U.S. model components and reprogramming as described in the petition and its attachments.

Standard No. 108

Lamps, Reflective Devices and Associated Equipment:

Replacement of the front and rear side marker lamps, headlamps and tail lamps with U.S.-conforming components and reprogramming the associated ECU software as described in the petition and its attachments.

Standard No. 110

Tire Selection and Rims:

Installation of the required tire information placard.

Standard No. 111

Rearview Mirrors:

Inscription of the required warning statement on the face of the passenger side rearview mirror or replacement of the mirror with the U.S. model mirror.

Standard No. 114

Theft Protection:

Reprogramming the body and ECU programs to activate the key warning and seat belt warning systems as described in the petition and its attachments.

Standard No. 118

Power-Operated Window, Partition, and Roof panel System:

Reprogramming of the vehicle ECU, as described in the petition and its attachments to meet the requirements of the standard.

Standard No. 138

Tire Pressure Monitoring Systems:

Reprogramming of the vehicle ECUs and replacement or addition of TPMS components with U.S.-model components as necessary to meet the requirements of the standard as described in the petition and its attachments.

Standard No. 207

Seating Systems:

Replacement of all seats with U.S.-model seats if necessary to meet the requirements of the standard and FMVSS No. 208, as described in the petition and its attachments.

Standard No. 208

Occupant Crash Protection:

Replacement of any seat belts, airbags, sensors, control units (ECU), wiring harnesses, knee bolsters, braces and software that are not identical to the U.S. model components with U.S. model components.

After installation of any new components, verification of system compliance will be completed as stated in the petition and its attachments.

Standard No. 209

Seat Belt Assemblies:

Replacement of the passenger seat belt assembly with U.S. model components as necessary to meet the requirements of the standard.

Standard No. 225

Child Restraint Anchorage Systems:

Replacement of or addition of anchorage components with U.S. model components as necessary to meet the requirements of the standard.

Standard No. 301

Fuel System Integrity:

The fuel system will need to be modified as described in the petition and its attachments as necessary to meet the requirements of the standard.

Standard No. 401

Interior Trunk Release:

A trunk release mechanism must be installed to meet the requirements of the standard.

All comments received before the close of business on the closing date indicated above will be considered, and will be available for examination in the docket at the above addresses both before and after that date. To the extent possible, comments filed after the closing date will also be considered. Notice of final action on the petition will be published in the

Federal Register

pursuant to the authority indicated below.

Authority:

49 U.S.C. 30141(a)(1)(A), (a)(1)(B), and (b)(1); 49 CFR 593.7; delegation of authority at 49 CFR 1.95 and 501.8.

Jeffrey M. Giuseppe,

Director, Office of Vehicle Safety Compliance.

[FR Doc. 2016-17191 Filed 7-20-16; 8:45 am]

BILLING CODE 4910-59-P