Certification of Airports

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Parts 121 and 139

[Docket No. FAA-2000-7479; Notice No. 00-05]

RIN 2120-AG96

Certification of Airports

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

This document proposes to revise the current airport certification regulation and to establish certification requirements for airports serving scheduled air carrier operations in aircraft with 10-30 seats. In addition, changes are proposed to address National Transportation Safety Board (NTSB) recommendations and petitions for exemptions and rulemaking. A section of an air carrier operation regulation also would be amended to conform with proposed changes to airport certification requirements. The FAA believes that these proposed revisions are necessary to ensure safety in air transportation and to provide a comparable level of safety at all certificated airports.

DATES:

Comments must be submitted on or before September 19, 2000.

ADDRESSES:

Comments on this proposed rulemaking should be mailed or delivered, in duplicate, to: U.S. Department of Transportation Dockets, Docket No. FAA-2000-7479, 400 Seventh Street, SW., Room Plaza 401, Washington, DC 20590. Comments may be filed and examined in Room Plaza 401 between 10 a.m. and 5 p.m. weekdays, except Federal holidays. Comments also may be sent electronically to the Dockets Management System (DMS) at the following Internet address: http://dms.dot.gov at any time. Commenters who wish to file comments electronically, should follow the instructions on the DMS web site.

FOR FURTHER INFORMATION CONTACT:

Linda Bruce, Airport Safety and Operations Division (AAS-300), Office of Airport Safety and Standards, Federal Aviation Administration, 800 Independence Ave., SW., Washington, DC 20591; telephone: (202) 267-8553, or E-mail: linda.bruce@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

Interested persons are invited to participate in this rulemaking by submitting such written data, views, or arguments, as they may desire. Comments relating to the environmental, energy, federalism, or economic impact that might result from adopting the proposals in this document are also invited. Substantive comments should be accompanied by cost estimates. Comments should identify the regulatory docket or notice number and should be submitted in triplicate to the Rules Docket address specified above.

All comments received, as well as a report summarizing each substantive public contact with FAA personnel on this rulemaking, will be filed in the docket. The docket is available for public inspection before and after the comment closing date.

The Administrator will consider all comments received on or before the closing date before taking action on this proposed rulemaking. Comments filed late will be considered as far as possible without incurring expense or delay. The proposals contained in this rulemaking may be changed in light of the comments received.

Commenters wishing the FAA to acknowledge receipt of their comments submitted in response to this notice must include a pre-addressed, stamped postcard with those comments on which the following statement is made: “Comments to Docket No. FAA-2000-7479.” The postcard will be date stamped and mailed to the commenter.

Availability of NPRMs

An electronic copy of this document may be downloaded using a modem and suitable communications software from the FAA regulations section of the FedWorld electronic bulletin board service (telephone: 703-321-3339), or the Government Printing Office's (GPO's) electronic bulletin board service (telephone: 202-512-1661).

Internet users may reach the FAA's web page at http://www.faa.gov/avr/arm/nprm/nprm.htm or the GPO's web pages at http://www.access.gpo.gov/nara for access to recently published rulemaking documents.

Any person may obtain a copy of this NPRM by submitting a request to the Federal Aviation Administration, Office of Rulemaking, ARM-1, 800 Independence Avenue, SW., Washington, DC 20591, or by calling (202) 267-9680. Communications must identify the notice number or docket number of this NPRM.

Persons interested in being placed on the mailing list for future NPRM's should request from the above office a copy of Advisory Circular No. 11-2A, Notice of Proposed Rulemaking Distribution System, that describes the application procedure.

Background

History

Since 1970, the FAA Administrator has had the statutory authority to issue airport operating certificates to airports serving certain air carriers and to establish minimum safety standards for the operation of those airports. This authority is currently found in Title 49, United States Code (U.S.C.) section 44706, Airport operating certificates. The FAA uses this authority to issue requirements for the certification and operation of certain land airports. These requirements are contained in Title14, Code of Federal Regulations part 139 (14 CFR part 139), Certification and Operations: Land Airports Serving Certain Air Carriers, as amended.

Until recently, this statutory authority was limited to those land airports serving passenger operations of an air carrier that is conducted with an aircraft having a seating capacity of more than 30 passengers. However, this authority was broadened by the Federal Aviation Administration Reauthorization Act of 1996. Section 44706 was amended to allow the FAA to certificate airports, with the exception of those located in the State of Alaska, that serve any scheduled passenger operation of an air carrier operating aircraft designed for more than 9 passenger seats but less than 31 passenger seats. FAA's existing authority to certificate airports serving air carrier operations conducted in aircraft with more than 30 seats remained unchanged.

This amendment was proposed by the Secretary of Transportation in response to a recommendation made by the NTSB that the FAA seek authority from Congress to issue certificates to airports serving commuter airlines. In November 1994, the NTSB released its findings resulting from a study of commuter airline safety.

1

This study identified several safety improvements that the NTSB felt would improve the commuter airline safety record. While this study, and subsequent recommendations, focused on airline and aircraft operations, it also was critical of the FAA for not requiring airports serving commuter operations to maintain their facilities in the same manner as airports serving major air carriers.

1

Safety Study: Commuter Airline Safety,

National Transportation Safety Board, NTSB/SS-94/02, November 1994.

This was not the first attempt to obtain the legislative authority to certificate commuter airports. In 1987, the General Accounting Office (GAO)

issued a safety report on the certification of small airports.

2

Similar to the NTSB findings, the GAO concluded that airport safety would be enhanced if all airports serving scheduled air carrier service were to be certificated and recommended the FAA include such facilities in its airport certification program. The FAA concurred with the GAO's findings, but determined its statutory authority to certificate airports was limited to airports that serve scheduled and unscheduled passenger operations of air carrier aircraft with more than 30 seats. A proposed amendment to broaden this authority was submitted to Congress, but the measure was not enacted.

2

Aviation Safety: Commuter Airports Should Participate in the Airport Certification Program,

U.S. General Accounting Office, GAO/RCED-88-41, November 1987.

The 1996 amendment to the statute did not mandate the issuance of airport certificates to airports serving commuter air carriers. It only provides general authority under which the FAA may promulgate appropriate regulatory standards. The FAA proposes to use this authority to extend to airports its policy of one level of safety for all covered air carriers. In response to a series of commuter accidents and the NTSB's findings, the FAA established this policy of one level of safety, and comprehensively revised regulations pertaining to the air carrier operations, specifically 14 CFR parts 121 and 135, to ensure similar safety standards among air carriers. Similarly, this proposal would establish minimum safety standards among all covered airports (airports that the FAA has the authority to certificate) served by air carriers.

Further, this proposal would revise and clarify several safety and operational requirements that have become outdated. The last major revision of part 139 occurred in November 1987, and since then, industry practices and technology have changed. In the subsequent years, the FAA has gathered data on the effectiveness of part 139 requirements, (primarily through joint industry/FAA working groups, field research and periodic airport certification inspections), and proposes to use this rulemaking opportunity to update part 139 requirements.

Current Requirements

Under existing part 139, the FAA requires airport operators to comply with certain safety requirements prior to serving operations of large air carrier aircraft (aircraft with more than 30 seats). When an airport operator satisfactorily complies with such requirements, the FAA issues to that facility an airport operating certificate that permits an airport to serve large air carriers. These safety requirements cover a broad range of airport operations, including the maintenance of runway pavement, markings and lighting; notification of air carriers of unsafe or changed conditions; and preparedness for aircraft accidents and other emergencies. The FAA periodically inspects these airports to ensure continued compliance with part 139 safety requirements.

Under existing rules, the FAA issues two types of airport operating certificates depending on the type of air carrier operations an airport serves. Operators of airports that serve scheduled operations of large air carrier aircraft are issued an Airport Operating Certificate (AOC), commonly referred to as a “full” certificate. As these airport operators regularly serve large air carrier operations, they must fully comply with all part 139 requirements. Of the approximately 660 certificated airports, approximately 430 airport operators hold a “full” certificate. Conversely, airport operators serving only unscheduled operations of large air carrier aircraft are required to have a Limited Airport Operating Certificate (LAOC), known as a “limited” certificate. Approximately 135 airport operators hold a “limited” certificate. Air carrier operations in large aircraft are so infrequent at these facilities that their operators are only required to comply with part 139 in a limited manner. For example, existing § 139.213 requires airport operators holding a “limited” certificate to comply with only certain pavement, lighting, marking and emergency response requirements. Such airports are typically located in remote communities or support seasonal activities, such as skiing during winter months.

The remaining certificated airports (approximately 90) are Department of Defense (DOD) airports serving air carrier operations. These facilities are issued an airport operating certificate but are exempted from part 139 requirements under FAA Exemption No. 5750B.

The FAA requires all operators of certificated civilian airports to develop, and comply with, a written document that details how the airport operator will comply with the requirements of part 139. As every airport is unique and local circumstances vary, this written document sets forth the site-specific procedures, equipment, and personnel that each airport operator uses to comply with part 139 requirements. This document at an airport with a “full” certificate is called the Airport Certification Manual (ACM). At an airport with a “limited” certificate, it is known as Airport Certification Specifications (ACS).

Enforcement Action

The FAA can impose a civil penalty of $1,000 per day per violation on operators of airports that are currently certificated under part 139 (airports serving scheduled and unscheduled operations of large air carrier aircraft). If this proposal is adopted, the FAA also could impose monetary penalties on airport operators serving scheduled operations of small air carrier aircraft for any failure to comply with the requirements of their certification manual or part 139. However, the FAA does consider mitigating circumstances, including an airport operator's willingness to correct any deficiencies and ability to pay civil penalties.

In its inspection role, the FAA works with airport operators and encourages a cooperative relationship between the certificate holder and inspectors, and commonly uses administrative actions to have most discrepancies corrected. Civil penalties and in extreme cases, certificate action, are levied against airport operators only as a last resort to gain compliance.

New Certificate Holders

If this proposal is adopted, airport operators not currently certificated by the FAA would be required to apply for a certificate under part 139 in order to serve certain air carrier operations. Such airport operators would contact the appropriate FAA Regional Airports Division office to initiate the application process. Once contacted, the FAA Regional Airports Division office would interview the airport operator to obtain information about the airport and air carrier operations served (or anticipated to be served). If the FAA determines that a certificate is necessary, the airport operator would be provided an application for certification (FAA Form 5280-1, Airport Operating Certification Application) and guidance materials.

The airport operator would submit a completed application (as specified under proposed § 139.103) to the FAA Regional Airports Division office for approval. As part of the application package, the airport operator would provide the FAA two copies of its proposed airport certification manual and written documentation as to when air carrier service will begin. The FAA would review the application and associated documentation to ensure that

they are complete and conduct an inspection of the airport for compliance with the requirements of part 139.

The FAA will issue an airport operating certificate if the application and other required documentation meets the provision of part 139, and the inspection reveals that airport is in compliance with part 139. The certificate may include other provisions the FAA finds necessary to ensure safety in air transportation (see discussion of proposed § 139.103 Application for certificate and § 139.105 Inspection authority).

Assistance is available for applicants applying for an airport operating certificate. FAA regional offices offer guidance and support to airport operators in complying with part 139. Access to the FAA is available by telephone, e-mail, conventional mail, regional newsletters, and on-site visits. In addition, the FAA makes available to airport operating certificate applicants, free of charge, advisory circulars, informational brochures, and safety placards to assist the certificate holder in complying with the requirements of part 139. The FAA regional offices also will assist airport operators in applying for Federal funds that may be used to comply with the requirement of part 139.

The Role of the Aviation Rulemaking Advisory Committee

The FAA has established an Aviation Rulemaking Advisory Committee (ARAC) to provide advice and recommendations to the FAA Administrator concerning a range of FAA's rulemaking activity, including air carrier operations, airman certification, aircraft certification, airports, security, and noise. The committee affords the FAA a forum to easily obtain direct, firsthand information and insight from affected interests through meeting together and exchanging ideas with respect to proposed rules and existing rules that should be revised or eliminated. While the activities of the ARAC do not circumvent the normal coordination process or the public rulemaking procedures, the committee's recommendations on a particular issue or proposed rule are taken under consideration by the FAA and fully disclosed in the public docket.

The ARAC consists of approximately 65 government, industry, labor, and consumer advocacy organizations selected by the FAA to represent various viewpoints of those impacted by FAA regulations. These members are organized into several issue areas to address specific technical subjects, including airport certification. The ARAC only undertakes those tasks requested by the FAA. Meetings of the ARAC are open to the public and interested persons with expertise in the subject matter are invited to participate.

To assist in the certification of airports serving smaller air carrier operations, the FAA requested the ARAC's advice and recommendations on what requirements should be applicable to airports that have scheduled service with aircraft having a seating capacity of 10-30 seats [60 FR 21582, May 2, 1995]. In developing these recommendations, the FAA asked the ARAC to consider alternatives to minimize the operational burden on smaller facilities, including options for aircraft rescue and firefighting (ARFF) services. The FAA also suggested the ARAC conduct a survey of affected airports to gauge the impact of any proposed requirement. At the time of this request, the FAA did not have the statutory authority to regulate airports serving scheduled operations of air carrier aircraft with 10-30 seats.

The ARAC accepted this task and established a Commuter Airport Certification Working Group to develop recommendations on this issue. Comprised of members of the main committee, the working group's membership included representatives from the following organizations:

1. Air Line Pilots Association

2. Aircraft Owners and Pilots Association

3. American Association of Airport Executives

4. National Air Transportation Association

5. National Association of State Aviation Officials

6. Regional Airline Association

The FAA and Landrum and Brown, an airport planning and engineering consulting firm, also provided technical support.

Over the course of a year, the Commuter Airport Certification Working Group met five times to research the issue and develop recommendations for the ARAC. The working group initially endeavored to establish a voluntary industry standard consistent with the FAA's lack of authority to regulate airports serving commuter operations. However, after the passage of Public Law 104-264, the FAA requested the working group to immediately finish its report and to take a regulatory approach to the certification of airports serving small air carrier aircraft. This action was based on the FAA's decision to exercise its new authority to regulate airports serving small air carrier operations.

While the working group agreed on many issues, two members (primarily the Air Line Pilots Association (ALPA)) disagreed with several of the group's recommendations. This minority differed on six regulatory requirements, including marking and lighting; ARFF; and handling of hazardous substances and materials. Subsequently, the working group developed both a majority and minority position at the FAA's request. Individual working group members also provided comments on issues when their respective organizations differed from the position taken by the ARAC working group.

In February 1997, both the majority and minority views of the working group, and those of individual work group members, were presented to the FAA. Overall, the working group majority recommended that a non-regulatory approach to improve commuter airport safety could accomplish the same level of safety as regulating these airports. In light of the proposed rulemaking, the majority suggested that such a regulation should focus on accident prevention rather than accident mitigation, particularly due to the limited public funds available to these small airports.

Despite its opposition to a rulemaking, the ARAC did provide, as requested by the FAA, proposed regulatory language for the certification of airports serving scheduled operations of small air carrier aircraft. The FAA considered this proposed regulatory language in this rulemaking and where possible, discusses ARAC's concerns for each proposed requirement in the following Section-by-Section analysis. As appropriate, both the majority and minority positions are discussed. However, the decisions in this document are the FAA's. Neither the majority opposition to rulemaking, nor the minority support of rulemaking, was a deciding factor in the FAA's decision to institute this rulemaking.

As requested by the FAA, the ARAC also conducted a survey of airports that might be affected to determine what safety practices are already being conducted and the potential operational and economic impact if these airports were to comply with existing part 139 requirements. This survey requested information on rescue and firefighting capabilities, airport staff, certification status, annual enplanements, existing marking, lighting and signs, and capital and recurring costs of certain equipment and procedures. The results of this survey are included with the ARAC final recommendations on commuter airport certification, filed in the public docket (see

ADDRESSES

). These survey

results also are discussed in the economic analysis associated with this rulemaking. Also, a copy of the economic analysis is filed in the docket and a summary of it is included in this proposal.

Much of the work done by the ARAC was the result of its members' willingness to donate their time and resources to travel to meetings and conduct research. The FAA wishes to recognize this contribution and appreciates the working group's effort to develop recommendations that represent a balance of safety and economic considerations.

Alternatives

This NPRM addresses two issues: (1) the revision of certain requirements of 14 CFR part 139, and (2) certification requirements of airports serving scheduled air carrier operations with 10-30 seat aircraft under 14 CFR part 139.

The FAA considered alternatives for each of these issues. Based on this analysis, the FAA determined that it was necessary to revise 14 CFR part 139 and that the revised part 139 should include the certification of airports serving scheduled air carrier operations with 10-30 passenger seat aircraft. See a more detailed description of these alternatives in the “Description of Alternatives” section that follows the “Section-by-Section Analysis.”

General Discussion of the Proposal

This proposal would comprehensively revise the airport certification process by including airports serving small air carrier aircraft to ensure these airports meet a minimum level of safety comparable to airports already certificated. Operators of airports serving small air carrier aircraft and currently not regulated under part 139 (approximately 40 airports) would be required to develop and implement an ACM, and to comply with certain safety and operational requirements. These airport operators, however, would be permitted some flexibility in complying with more burdensome requirements.

In addition to serving large, unscheduled air carrier aircraft, approximately 120 of the approximately 135 airports holding a LAOC also serve scheduled small air carrier aircraft. To address these additional operations, this proposal would require the operators of these 120 airports to implement existing safety measures (such as aircraft rescue and firefighting) on a more frequent basis and comply with additional safety requirements. The remaining 15 airport operators holding a LAOC would continue to comply with part 139 requirements as they do today.

Likewise, this proposal would require airport operators holding an AOC (or a “full” certificate), approximately 430 airports, to continue to comply with part 139 requirements as they do today. These airport operators would be required to revise their certification manuals and comply with proposed modifications to existing requirements. The operators of approximately 50 of these airports also may be required to implement certain safety measures on a more frequent basis if they serve small air carrier operations that do not occur concurrently with large air carrier aircraft operations.

In addition, this proposal would clarify that airports operated by the United States government, including DOD, are not subject to part 139. Subsequently, the 90 DOD airports currently certificated under part 139 would no longer need to request an exemption from part 139 requirements to continue serving air carrier operations.

To minimize confusion resulting from the inclusion of airports serving small air carrier aircraft operations into the FAA's existing airport certification program, the FAA is proposing to reclassify airport operating certificates and certification manuals. Instead of differentiating between an AOC and a LAOC, and creating additional types of airport operating certificates, this proposal would provide for only one type of certificate, an AOC, and no longer make a distinction between an ACM and an ACS. All airport certificate holders would be required to adopt and implement an ACM, regardless of size and type of air carrier operations.

All holders of airport operating certificates would be issued new certificates, including those existing airport operators holding “full” or “limited” certificates. Operators of currently certificated airports would not be required to reapply for an airport operating certificate. if this proposal is adopted, the FAA would convert existing certificates, as appropriate.

The FAA proposes to continue to distinguish between airports that serve different sizes or types of air carriers, and establish requirements appropriate for each type of airport. Under this proposal, similar airports would be grouped into four new classes, I-IV, and requirements are proposed for each new class of airport. This approach would ensure that airports serving small air carrier aircraft or unscheduled air carrier operations (

e.g.,

charter flights) are not unduly burdened with requirements more appropriate for airports serving frequent operations of large air carriers. In addition, these new classes of airports address those airports that serve a mixture of air carrier operations.

Airports serving all types of scheduled operations of large air carrier aircraft, and any other type of air carrier operations, would be known as Class I airports. Operators of these airports would be required to comply with all part 139 requirements. Essentially, all airport operators holding an existing “full” certificate would become Class I airports.

Class II airports would be those airports that serve scheduled operations of small air carrier aircraft (10-30 seats) and unscheduled operations of larger air carrier aircraft (more than 30 seats). Airports that would be classified as Class II would be those existing “limited” certificate airports that serve scheduled operations by small air carrier aircraft.

Class III airports would be those airports that serve only scheduled operations of air carrier aircraft with 10-30 seats. Class III airports would be those facilities newly certificated as the result of this rulemaking.

Class IV airports would be those airports currently with a “limited” certificate serving only unscheduled air carrier operations in aircraft with more than 30 seats.

Airports in the State of Alaska that serve large air carrier operations would continue to be certificated under part 139, as Class I or Class IV airports. No requirements are proposed, as specified in the authorizing statute, for those airports in the State of Alaska that only serve scheduled operations of smaller air carrier operations.

The FAA currently requires operators of certificated airports to develop an ACM or ACS, depending on the type of certification, to detail how the airport operator will comply with the requirements of part 139. As every airport is unique, it is difficult to impose requirements that prescribe exacting technical standards that would work at every airport. Instead the FAA sets forth performance-based standards that airport operators implement in the manner best suited to their facilities.

In this manner, the FAA can vary requirements that airport operators must comply with. For example, existing § 139.213 requires operators of “limited” certificated airports to include in their ACS procedures to comply with seven operational requirements found in Subpart D, whereas operators of “full” certificated airports must provide for all part 139 requirements in their manual. This proposal takes a similar approach

and proposes different requirements and manual content for each new airport class.

Under this proposal, the requirements for manual content would vary between the airport classes, with the most comprehensive manual required of Class I airports. Operators of Class I airports would have to comply with more safety requirements than the operators of Class II, III, and IV airports as they serve more complex and varied air carrier operations.

As a consequence of these proposed changes, several existing sections of the regulation would be combined and the current numbering scheme of subparts C and D would be altered. The following chart illustrates these changes, comparing existing section titles and numbering against those proposed.

Comparison of Section Titles and Numbering Between Existing and Proposed Part 139

Existing part 139

Proposed part 139

Subpart A—General

§ 139.1 Applicability

§ 139.1 Applicability.

§ 139.3 Definitions

§ 139.3 Delegation of authority (new section—§ 139.3 would be moved to proposed § 139.5).

§ 139.5 Standards and procedures for compliance with the certification and operations requirements of this part

§ 139.5 Definitions (section number change—§ 139.5 would be moved to proposed § 139.7).

§ 139.7 Methods and procedures for compliance (title and section number change).

Subpart B—Certification

§ 139.101 Certification requirements: General

§ 139.101 General requirements (title change).

§ 139.103 Application for certificate

§ 139.103 Application for certificate.

§ 139.105 Inspection authority

§ 139.105 Inspection authority (revised section—§§ 139.105 and .301 would be combined to form proposed § 139.305).

§ 139.107 Issuance of certificate

§ 139.107 Issuance of certificate.

§ 139.109 Duration of certificate

§ 139.109 Duration of certificate.

§ 139.111 Exemptions

§ 139.111 Exemptions.

§ 139.113 Deviations

§ 139.113 Deviations.

Subpart C—Airport Certification Manual (title change)

§ 139.201 Airport operating certificate: Airport certification manual

139.201 General requirements. (title change—§§ 139.201, .203, .207, .209, .211, and .215 would be combined to form proposed § 139.201).

§ 139.203 Preparation of airport certification manual

§ 139.203 Contents of airport certification manual (new section—§§ 139.205 and 139.213 would combined to form proposed § 139.203).

§ 139.205 Contents of airport certification manual

§ 139.205 Amendment of airport manual (section number change—§ 139.217 would be moved to proposed § 139.205).

§ 139.207 Maintenance of airport certification manual

§ 139.209 Limited airport operating certificate: Airport certification specifications

§ 139.213 Contents of airport certification specifications

§ 139.215 Maintenance of airport certification specifications

§ 139.217 Amendment of airport certification manual or airport certification specifications

Subpart D—Operations

§ 139.301 Inspection authority

§ 139.301 Records (new section—§ 139.301 would be moved to proposed § 139.105).

§ 139.303 Personnel

§ 139.303 Personnel.

§ 139.305 Paved areas

§ 139.305 Paved areas.

§ 139.307 Unpaved areas

§ 139.307 Unpaved areas.

§ 139.309 Safety areas

§ 139.309 Safety areas.

§ 139.311 Marking and lighting

§ 139.311 Marking, signs, and lighting (title change).

§ 139.313 Snow and ice control

§ 139.313 Snow and ice control.

§ 139.315 Aircraft rescue and firefighting: Index determination

§ 139.315 Aircraft rescue and firefighting: Index determination.

§ 139.317 Aircraft rescue and firefighting: Equipment and agents

§ 139.317 Aircraft rescue and firefighting: Equipment and agents.

§ 139.319 Aircraft rescue and firefighting: Operational requirements

139.319 Aircraft rescue and firefighting: Operational requirements.

139.321 Handling and storing of hazardous substances and materials

139.321 Aircraft rescue and firefighting: Exemptions (new section—existing § 139.321 would be moved to proposed § 139.323).

§ 139.323 Traffic and wind direction indicators

§ 139.323 Handling and storing of hazardous substances and materials (section number change).

§ 139.325 Airport emergency plan

§ 139.325 Traffic and wind direction indicators (section number change).

§ 139.327 Self-inspection program

§ 139.327 Airport emergency plan (section number change).

§ 139.329 Ground vehicles

§ 139.329 Self-inspection program (section number change).

§ 139.331 Obstructions

§ 139.331 Ground vehicles (section number change).

§ 139.333 Protection of navaids

§ 139.333 Obstructions (section number change).

§ 139.335 Public protection

§ 139.335 Protection of navaids (section number change).

§ 139.337 Wildlife hazard management

§ 139.337 Public protection (section number change).

§ 139.339 Airport condition reporting

§ 139.339 Wildlife hazard management (section number change).

§ 139.341 Identifying, marking, and reporting construction and other unserviceable areas

§ 139.341 Airport condition reporting (section number change).

§ 139.343 Noncomplying conditions

§ 139.343 Identifying, marking, and reporting construction and other unserviceable areas (section number change).

§ 139.345 Noncomplying conditions (section number change).

As noted earlier, changes are proposed to operational and safety requirements. The specifics of these revisions are discussed in detail in the following section, “Section-by-Section Analysis.” The proposed revisions reflect changes to technology and industry practice. This action does not address runway friction measurement (both winter and maintenance), runway distance remaining signs, and certain requirements related to ARFF equipment, training, and extinguishing agents. The FAA is continuing to review these issues with industry representatives (primarily through the ARAC) and may propose rulemaking as a result of these efforts in a separate action.

Throughout the proposed rule, references are made to 49 U.S.C. 44706. This statute is the recodification of the FAA's authority to prescribe airport certification regulations previously found in the Federal Aviation Act of 1958, 49 U.S.C. App. 1432

et seq.

Additionally, the FAA proposes to revise the title of 14 CFR part 139, “Certification and Operations: Land Airports Serving Certain Air Carriers” to “Certification of Airports.”

Request for Additional Information

Throughout this proposal, the FAA is requesting economic and operational information on specific topics. As explained in the following Section-by-Section Analysis, the FAA intends to use this information to further analyze certain proposed requirements. Additional information is requested on the following subject areas:

1.

Certification of heliports.

Under the discussion of proposed § 139.1, the FAA is requesting comments on the need to certificate heliports, including recommendations on certification requirements and any associated safety and economic considerations that should be addressed.

2.

Reduction or revocation of an airport operating certificate.

Under proposed § 139.109, information is requested as to why it would be more costly for an airport operator to surrender an airport operating certificate and then later to regain it, than it is to maintain a certificate uninterrupted.

3.

Retro-reflective runway and taxiway signs.

The FAA is soliciting comments under proposed § 139.311 on the use of retro reflective guidance and directional signs at airports serving small or unscheduled air carrier aircraft.

4.

ARFF Exemption.

The FAA requests comments on the new ARFF exemption process delineated under proposed § 139.321.

5.

Implementation.

Finally, the FAA is requesting comments on various elements of the implementation schedule, should this proposal be adopted.

Section-by-Section Analysis

Subpart A—General

Section 139.1 Applicability

Section 139.1 establishes that part 139 prescribes rules for the certification and operation of airports serving certain air carrier operations. This proposal expands this section by amending and reorganizing existing language into new paragraphs (a) and (b).

New paragraph (a) would incorporate a new group of airports that would require an airport operating certificate

(AOC) before serving certain air carrier operations. In addition to those airports already certificated under part 139, airports serving scheduled operations of air carrier aircraft seating 10 to 30 passengers would require a certificate under this part. This expansion of the rule's applicability would reflect recent revisions to 49 U.S.C. 44706, that authorized the Administrator to issue an AOC to airports serving any scheduled operations of an air carrier operating aircraft designed for more than 9 passenger seats but less than 31 passenger seats.

Throughout paragraph (a), references to the term “aircraft seating capacity” would be changed to “aircraft design.” This proposal would more accurately reflect how the FAA and other civil aviation authorities certificate air carrier aircraft for passenger operations. This revision would have no effect on how aircraft passenger seating capacity is determined. An FAA-issued aircraft type certificate and its foreign equivalent specify passenger seating capacity and may only be changed by amendment to the aircraft type certificate.

Further, the FAA proposes to move language currently found in § 139.101(a) to new paragraph § 139.1(a). The phrase specifies that part 139 is applicable to land airports in the United States, the District of Columbia, or any U.S. territory or possession. This language is more appropriate in § 139.1, Applicability.

Proposed paragraph § 139.1(b) would group together the type of airports that would be exempt from part 139. As currently is the case, airports serving air carrier operations only because they have been designated as alternate airports (under § 121.590) would not be certificated under part 139. The revised part 139 also would not be applicable, as specified in the authorizing statute, at airports in the State of Alaska that serve scheduled operations of air carrier aircraft seating 10-30 passengers. However, airports in the State of Alaska that serve scheduled and/or unscheduled operations of air carrier aircraft with more than 30 passenger seats and serve smaller scheduled air carrier operations must be certificated under part 139. Under this proposal, these airports would be certificated as a Class I or Class IV airport because they serve larger air carrier operations.

In addition, airports operated by U.S. government agencies would not be required to comply with part 139. The FAA has issued airport operating certificates, under FAA Exemption No.

5750, to Department of Defense (DOD) airports that serve civilian commercial carriers. Standards for military airports, and others operated by other branches of the Federal government (e.g., NASA, Dept. of Energy), differ from those prescribed under part 139.

The FAA does not have the statutory authority to regulate airports operated by U.S. government agencies. Since the continuance of commercial flights into these facilities is necessary to support federal government requirements, the FAA proposes to eliminate exemptions to U.S. government entities, (such as DOD's exemption to part 139) but will allow U.S. government entities to apply for an AOC for air carrier operations. Changes to part 121 are proposed to permit air carriers to use such airports (see discussion under proposed § 121.590, Use of certificated land airports).

This does not address airports where civilian and military operations commingle. These airports are known as either “joint-use airports” or “shared-use airports.”

Joint-use airports are owned by the U.S. government, which leases or surpluses a portion of their facility to the local government for civilian air carrier operations. Shared-use airports are co-located U.S. and local government facilities at which portions of the movement areas, such as runways, taxiways, and ramps are shared. Under this proposal, civilian air carrier operations of either a joint-use airport or a shared-use airport will come under the purview of part 139.

Also, this proposal excludes heliports. The focus of this proposal is on the safety needs of airports serving fixed wing aircraft. While concerned with the safe operations of helicopters, the FAA believes certification of heliports should be handled separately and is considering how to certify these facilities. The FAA is requesting comments on the need to certificate heliports. The FAA requires specific recommendations on certification requirements and associated safety and economic considerations.

Section 139.3 Delegation of Authority

Under this proposal, existing § 139.3, titled “Definitions,” would be moved to proposed § 139.5. Proposed § 139.3 would be titled “Delegation of Authority.” This section would be new.

This new section would set forth FAA's existing delegation authority that allows FAA employees to act on behalf of the FAA Administrator in the oversight of the certification of airports. As proposed, the Administrator's delegation of authority has not changed, and the FAA's Associate Administrator for Airports could act in the capacity of the Administrator.

Section 139.5 Definitions

In this proposal, existing § 139.3 would be redesignated as proposed § 139.5. Existing § 139.3 establishes terms, and their definitions, used in part 139. The definitions contained in this revised section reflect proposed changes made throughout the rule. As such, several existing definitions have been modified or deleted and new definitions are proposed.

The FAA proposes to delete the existing term “air carrier aircraft.” Two new terms, “large air carrier aircraft” and “small air carrier aircraft,” have been added to part 139 to differentiate requirements of airports serving differing sizes of air carrier aircraft. Proposed exclusively for part 139, these new definitions are based on the number of passenger seats of an air carrier aircraft, and should not be confused with existing definitions for “large aircraft” and “small aircraft” found in 14 CFR part 1 that classify aircraft by weight.

The term “air carrier” would no longer be defined in part 139. Instead, the definition of “air carrier,” as set out in 14 CFR part 1 would apply in part 139. The term “average daily departures” would be revised slightly by changing the phrase “consecutive months” to read “consecutive calendar months.” Other references throughout the rule to duration of time using months would be similarly updated to ensure clarity and consistency.

The term “airport operating certificate” would be modified to make reference to four new classes of certificated airports. The term “certificate holder” likewise would be modified to correspond with new airport classifications. References to subpart D and LAOC would be deleted. Instead, the term “certificate holder” would be used generically to describe any airport operator issued an AOC under part 139.

As described earlier, the FAA proposes to modify part 139 to change the process by which airports are categorized, and establish four new types of airport classes. These four classifications—Class I, II, III, and IV airports—would be added to existing definitions.

A Class I airport would serve the most varied types of air carrier operations. A Class I operator would be authorized to serve air carrier operations of large and small air carrier aircraft. Under this proposal, airports already certificated under part 139 to serve scheduled operations of large air carrier aircraft would be reclassified as Class I airports. The FAA anticipates approximately 430 airports would be certificated as Class I airports.

A Class II airport would serve scheduled operations of small air carrier aircraft and unscheduled passenger operations of larger air carrier aircraft. A Class II airport would not serve scheduled large air carrier aircraft. Airports classified as Class II would be those existing airports with a LAOC (airports serving unscheduled large air carrier aircraft) that serve scheduled operations by small air carrier aircraft. The FAA anticipates approximately 120 airports would be certificated as a Class II airport.

A Class III airport would serve scheduled operations of small air carrier aircraft. A Class III airport would not serve scheduled or unscheduled large air carrier aircraft.

Under the current regulation, airports meeting this criteria are not certificated. The FAA anticipates approximately 40 airports would be newly-certificated as Class III airports.

A Class IV airport would serve unscheduled passenger operations of large air carrier aircraft but would not serve scheduled large or small air carrier aircraft. Airports currently holding a LAOC, but not serving scheduled small air carrier operations, would be certificated as Class IV airports. The FAA anticipates approximately 15 airports would be certificated as Class IV airports.

The following table illustrates the types of air carrier operations each proposed category of airport can serve:

Type of air carrier operation

Proposed airport class

Class I

Class II

Class III

Class IV

Scheduled Large Air Carrier Aircraft

X

Unscheduled Large Air Carrier Airrcraft

X

X

X

Scheduled Small Air Carrier Aircraft

X

X

X

To reflect the proposed deletion of heliports from part 139, the term “movement area” would be modified to remove any reference to areas used by helicopters to hover or taxi.

The term “clean agent” would be added to specify a new type of aircraft fire extinguishing agent that an airport operator could use to comply with part 139 ARFF requirements. Clean agent is a term used by the firefighting community to describe a category of fire extinguishing agents that replace halon 1211 (see discussion of § 139.317, Aircraft rescue and firefighting: Equipment and agents). The proposed definition is based on National Fire Protection Association (NFPA) 2001, Standards on Clean Agent Fire Extinguishing Systems (1996 Edition), that establishes standards for halon 1211 substitutes. The NFPA is an independent, nonprofit organization that advocates consensus codes and standards, research, and education for fire and related safety issues. Many NFPA codes and standards are used as the basis for legislation and regulations in federal, state, and local governments.

In addition to NFPA 2001, the FAA is proposing that a clean agent used to comply with part 139 requirements would need to have the equivalent extinguishing action as halon 1211, as defined in FAA Technical Report DOT/FAA/AR-95/87. This document establishes a test protocol to measure an extinguishing agent's equivalency to halon 1211 and its appropriateness for use on aircraft fires.

In addition, the terms “scheduled operation” and “unscheduled operation” would be added to distinguish the types of operations served by the four classes of airports. The definition of “scheduled operation” is also found in 14 CFR part 119, Certification: Air carriers and commercial operators. A scheduled operation is conducted by an air carrier or a commercial operator in accordance with a published schedule for passenger operations that includes dates or times, and the operation is openly advertised or made available to the general public. Conversely, the definition of an “unscheduled operation” would be an operation conducted by an air carrier or a commercial operator that is specifically negotiated with the customer or that meets the definition of a supplemental operation found in part 119, Certification: Air carriers and commercial operators, or the definition of a public charter found in part 380, Public charters.

All other existing definitions would remain unchanged.

Section 139.7 Methods and Procedures for Compliance

In this proposal, existing § 139.5, titled “Standards and procedures for compliance with the certification and operations requirements of this part,” would be moved to proposed § 139.7. Existing § 139.5 specifies that an operator of a certificated airport must comply with the requirements of part 139 in a manner acceptable to the Administrator, and that methods and procedures contained in advisory circulars (AC's) are an acceptable means of compliance.

The relocated section would be titled, “Methods and procedures for compliance,” and would be clarified as described below. The FAA proposes to delete the language “with the certification and operations requirements of this part” from the title of existing § 139.5. This editorial change would ensure consistent section titles throughout the part. In addition, the term “standards” would be replaced with the term “methods” so as not to confuse the means of compliance (the methods) with the requirements of the regulations (the standards) prescribed in proposed subparts C and D.

With the addition of new airports to the part 139 process, the FAA believes existing language of this section should be clarified to eliminate any confusion. Several sentences would be combined and revised to state clearly that the use of methods and procedures provided in FAA AC's to comply with part 139 requirements are acceptable.

Advisory Circulars are developed in conjunction with the aviation industry to ensure consistent and reasonable means of complying with regulations. As technology and the aviation industry evolve the advisory circular process provides an expeditious means to revise guidance materials.

Certificate holders may comply with part 139 requirements by means other than those specified in the AC's. However, any alternative must be authorized by the FAA, and must provide the equivalent level of safety in meeting the requirements of part 139. This provision is repeated throughout this proposal in sections where advisory circulars are available to assist the certificate holder in meeting specific regulatory requirements proposed in the document.

Subpart B—Certification

Section 139.101 General Requirements

This NPRM proposes to retitle § 139.101, “Certification requirements: general,” as “General requirements,” and combines the text of existing paragraphs (a) and (b) into a new paragraph (a). New paragraphs (b) and (c) would be added. Existing § 139.101 specifies that no person may operate an airport in the U.S. and U.S. territories that serve certain types of air carrier operations without a part 139 certificate, or in violation of that certificate.

While proposed paragraph (a) combines existing § 139.101(a) and (b) into one paragraph, the requirement that an airport subject to this part may not be operated without an operating certificate, or in violation of its certificate, remains unchanged. References to LAOC's and ACS's would be replaced with proposed changes to the certification process. As mentioned earlier, references to land airports located in the United States or its territories would be moved to a more appropriate location in proposed § 139.1, Applicability.

The term “except as otherwise authorized by the Administrator” in existing paragraph (b) would be moved to new paragraph (a). This change would enable the FAA to authorize operations not covered by the regulation.

New paragraph (b) would require each airport operator to adopt, and comply with, an ACM in accordance with proposed requirements.

New paragraph (c) proposes that each airport class implement its ACM within a specified time. It is anticipated that under this proposal most airport operators will only need to document processes and procedures already in place. However, airport operators that would be required to develop an ACM for the first time, or to make extensive revisions to an existing manual, would have more time to comply than other airports. Staggering compliance dates also would permit adequate time for the FAA to process new and revised certification manuals.

Compliance with requirements for runway and taxiway signs, ARFF, and emergency plans would take additional time and corresponding sections of the ACM may not be completed within the timeframes specified in new paragraph (c). Certificated airport operators may need to seek Federal and local funding, order equipment, and train personnel. Consequently, additional time is proposed to implement these requirements (see discussions under proposed § 139.311, Marking, signs, and lighting; § 139.321, Aircraft rescue and firefighting: Exemptions; and § 139.327, Airport emergency plan).

The FAA is requesting comments on the proposed implementation schedules. If the commenter proposes alternative compliance dates, comments

should include supporting operational and economic data.

Section 139.103  Application for Certificate

Existing § 139.103 establishes requirements to apply for an airport operating certificate or an limited airport operating certificate. This proposal would amend existing § 139.103 by revising paragraphs (a) and (b) and by adding a new sentence to the beginning of this section. Proposed changes are intended to incorporate application requirements also found in existing §§ 139.201(a) and 139.209(a).

This section would continue to require an applicant for an AOC to prepare, and submit an application form and an airport certification manual to the Administrator for approval. References to LAOC and ACS also would be deleted in order to correspond to proposed changes to the certification process and classification of airports.

If this proposal is adopted, airport operators currently holding a certificate under part 139 would not be required to apply for a new AOC, but may need to amend an existing ACM or ACS.

Section 139.105 Inspection Authority

The FAA proposes to incorporate existing inspection authority provision of §§ 139.105 and 139.301 into one paragraph. Language referencing statutory authority also would be updated.

Existing § 139.105 states that an airport operator holding a certificate under part 139 must allow the FAA to make inspections to determine compliance with the regulation. This would not change. This new section would state that the Administrator may make inspections and tests to determine compliance with airport certification regulations.

References to the Federal Aviation Act of 1958 would also be removed and replaced with references to the current statutory authority. In addition, references to LAOC have been deleted.

Section 139.107 Issuance of Certificate

Existing § 139.107 specifies standards that must be meet before the FAA can issue a certificate. This NPRM would revise existing language into new paragraphs (a), (b), and (c), propose new requirements an applicant must meet, and deletes references to LAOC.

New paragraph (a) would require applicants to provide written documentation that air carrier service would begin on a specific date. The FAA intends to limit applicants for part 139 certification to those facilities with planned air service.

As presently required under § 139.107, new paragraph (b) would require an applicant for an AOC to meet the requirements for an ACM (as required under proposed § 139.103 and 139.203) prior to issuance of a certificate.

New paragraph (c) combines the remaining requirements of existing § 139.107. Also, the standard “public interest” would be replaced with the new standard “safety in air transportation” as required by the authorizing statute.

Section 139.109 Duration of Certificate

Existing § 139.109 states that a certificate issued under part 139 is effective until surrendered by the certificate holder, or suspended or revoked by the Administrator. This NPRM proposes to modify this section by placing existing language into new paragraph (a). A new paragraph (b) also is proposed and references to LAOC would be deleted.

New paragraph (b) stipulates that the Administrator may revoke an AOC if air carrier operations have not occurred for 24 consecutive months. However, in deciding whether to revoke an AOC because of lack of service, the FAA would consider the airport's reasonable expectation of future air carrier service.

In previous proposals to part 139, airport operators have recommended that the reduction or revocation of an airport operating certificate should be at the option of the airport operator and not the FAA. These commenters were concerned that if an airport later needed to regain its certification, the cost to do so would prove burdensome. The FAA does not agree with this cost assessment. The FAA requests comments (to include economic and operational data) as to why it would be more costly to surrender a certificate and then later to regain it, than it is to maintain a certificate uninterrupted.

An airport operator that has lost its certification can continue to comply with the requirements of its certification manual and the requirements of part 139 until it regains its certificate. While the FAA does not inspect non-certificated airports, the operators of such airports are encouraged to use part 139 as a guide to ensure safety. Further, many such airport operators would be required by Federal grant assurances to continue to implement elements of their certification program even when not certificated under part 139.

Under various statutes, the Federal Government is authorized to grant property, funds, and other assistance to local communities for the development of airport facilities. In return, airport owners assume certain obligations, either by contract or by restrictive covenants in property deeds that require the airport operator to maintain and operate its airport facilities safely, efficiently, and in accordance with specified conditions. These conditions are known as “grant assurances” and require the airport owner to comply with certain maintenance and operational conditions similar to those found in the requirements of part 139. For example, grant assurances require the airport operator to maintain pavements constructed or repaired with Federal assistance. These airport operators must also make arrangements for promptly marking, lighting and reporting hazards and other conditions affecting aeronautical use of the airport.

This revised section also proposes language enabling a certificate holder to appeal an order revoking its AOC. The appeal process is found in 14 CFR part 13.

Section 139.111 Exemptions

Existing § 139.111 establishes procedures for the certificate holder to petition for an exemption from the requirements of part 139. The FAA proposes to modify this section to reflect proposed changes to the format used for petitions for exemption from aircraft rescue and firefighting requirements.

Under revised paragraph (b), references to 14 CFR 11.25, Petitions for Rulemaking or Exemption, would be deleted. Instead, a new sentence would be added to the end of the paragraph that specifies that an applicant for, or holder of, an AOC desiring to petition from aircraft rescue and firefighting requirements must do so as prescribed under new § 139.321 (see discussion under proposed § 139.321, Aircraft rescue and firefighting: Exemptions).

Section 139.113 Deviations

This notice proposes to revise existing § 139.113 language to permit the certificate holder more flexibility during emergencies requiring deviation from some of part 139 requirements. Existing § 139.113 permits the certificate holder to deviate from requirements of subpart D of the regulation during emergency conditions.

As proposed, the standard “involving the transportation of persons by air carriers,” would be deleted from the first sentence. This standard was originally included in part 139 to ensure that airport resources and services would not be routinely used to respond to emergencies in the local community. However, this section has been subsequently interpreted as prohibiting

the certificate holder from deviating from part 139 requirements unless the emergency involves air carrier operations.

It was never the FAA's intent to restrict airport emergency services from assisting with occasional catastrophic events because an air carrier was not involved. No amount of pre-planning can cover every emergency scenario, and the FAA believes emergency service providers are best suited during an emergency to determine the appropriate response.

When a deviation occurs, it would be considered permissible under proposed § 139.113, so long as the certificate holder notifies the FAA within 14 days of the deviation. This change, however, is not meant to allow a certificate holder to take advantage of emergency situations to regularly deviate from the requirements of part 139. For instance, this proposed section is not intended to allow local municipalities to use the emergency services of a part 139 airport to routinely respond to emergencies in the surrounding community during air carrier operations. This section is intended only to allow a certificate holder to provide temporary assistance during occasional catastrophic or natural emergencies.

Certificate holders that are recipients of Federal funds also should note that this proposed section would not excuse them from any limitations or provision of their grant assurances that restrict the use of facilities and equipment purchased with Federal funds.

In addition, the term “airport certification manual” would be added to the first sentence of this paragraph to clarify that the certificate holder may, when responding to an emergency, deviate from both its certification manual and any requirements of subpart D.

The FAA further proposes to modify requirements of this section to allow the certificate holder to notify the FAA of deviations by telephone, or other means of electronic communications, rather than requiring an automatic written notification.

Subpart C—Airport Certification Manual

The FAA proposes to revise the title of this subpart by removing references to airport certification specifications. In general, the contents of subpart C would be clarified and requirements for airports serving scheduled operations of small air carrier aircraft have been included.

Section 139.201 General requirements

Existing § 139.201 requires applicants for an AOC to develop, and submit for approval, a certification manual.

This section also requires certificate holders to comply with their approved ACM.

This NPRM proposes to retitle this section from “Airport operating certificate: Airport certification manual,” to “General requirements.” In addition, the section would be revised to consolidate requirements of existing §§ 139.201, 139.203, 139.207, 139.209, 139.211, and 139.215 into a single section.

The FAA proposes the same general requirements for preparation and maintenance of ACM's for all certificated airports. Existing part 139 provides separate sections for the preparation and maintenance of an ACM and ACS, although the requirements of these sections are essentially the same.

New paragraphs (b) and (c) would set forth manual preparation, maintenance, and distribution requirements. The proposed changes clarify signature responsibilities of the certificate holder, and the necessity to document manual changes. In addition, these changes would require that any revision to the certification manual contain the FAA's approval, in addition to an approval date.

Also, the requirement that a certification manual be typewritten would be expanded to include any printed form. This change is intended to clarify that any type of printed form, whether produced on a typewriter, computer, etc., would be acceptable to the Administrator.

Existing §§ 139.201(a) and 139.209(a) would be deleted as the language in both these paragraphs duplicates the language of proposed § 139.103 (see the discussion of proposed § 139.103, Application for certificate). Also, the 1988 dates in existing §§ 139.201(c) and 139.209(c) would be deleted as these dates are no longer applicable.

Existing paragraph (b) provides guidance and an acceptable means of compliance with ACM requirements would be revised and moved to new paragraph (d). References to the specific series numbers within the AC system would be deleted. Instead, this new paragraph would make a general reference to the AC system. This will allow more flexibility in updating the AC numbering system, without requiring a subsequent revision to the regulation. References to specific AC series numbers would be similarly updated throughout subpart D.

Section 139.203 Contents of Airport Certification Manual

Under this proposal, existing § 139.203, titled “Preparation of airport certification manual,” would be moved to proposed § 139.201. Existing § 139.203 establishes standards for maintaining an ACM.

The contents of §§ 139.205 and 139.213 are combined in proposed new § 139.203. Additional requirements are proposed to correspond to the new classifications of certificated airports and changes to subpart D.

Similar to existing §§ 139.205(a) and 139.213(a), new paragraph (a) would require all classes of airports to include in their certification manual a description of procedures and equipment used to comply with subpart D and any other requirements of this section. However, existing language of §§ 139.205(a) and 139.213(a) would be revised. Existing §§ 139.205(a)(2) and 139.213(a)(2), specifying compliance with limitations imposed by the Administrator, would be moved to proposed new paragraph (b).

All certificate holders would be required to have an ACM, and new paragraph (b) would specify the manual contents for each class of airport. As noted above, the content of the manual would vary depending on the class of airport. The most comprehensive manual would be required for Class I airports because they serve more complex and varied air carrier operations.

A chart is proposed in new paragraph (b) to aid the certificate holder in determining the content of its manual. This chart lists the four proposed airport classifications and links each class to the appropriate certification manual element.

In revised § 139.203(b), proposed Class I airport certificate holders would be required to include in their ACM all elements that are currently required. In addition, this proposal would require the operators of these airports to incorporate into their ACM several new elements.

Class I airport certificate holders would include in their ACM a description of personnel training and equipment, and a system for maintaining records. This is intended to correspond to proposed new § 139.301 and proposed changes to existing § 139.303 (see the discussion under proposed section 139.301, Records; and 139.303, Personnel).

Airport operators currently holding a LAOC would be required to convert their existing ACS into an ACM. All elements that are presently required to

be in an airport certificate holder's ACS would be transferred into the new ACM.

Manuals for airports certificated as Class II and IV airports would include procedures to ensure safety in storing and handling hazardous materials, traffic and wind indicators, and self-inspections, as specified in subpart D.

These airport operators currently address these safety issues differently . Under existing part 139, these safety issues must be addressed in the ACS, but not necessarily in the manner prescribed under subpart D.

The FAA has found that most certificate holders with an LAOC already provide for these elements in their ACS, as required under existing subpart D. Part 139 requirements related to the handling of hazardous materials, wind and traffic indicators, and self-inspections represent good general airport operating practices that many of these airports already have adopted.

In addition, operators of airports certificated as Class II and IV airports would be required to include in their ACM a grid map or other means of identifying locations and terrain on and around the airport that are significant to emergency operations. For many years, airports serving scheduled large air carrier operations have been required to include this grid map in their certification manual. This map assists airport personnel in maintaining the airport, and emergency personnel in responding to incidents at the airport. As such, the FAA proposes that all certificate holders include a grid map in their ACM.

Operators of proposed Class II and IV airports also would be required to include in their ACM an emergency plan and procedures for, and descriptions of, recordkeeping and personnel training. This is intended to correspond to other proposed changes in the regulation. Unlike proposed Class I certificate holders, Class II and IV certificate holders would not have to include in their certification manuals provisions to conduct triennial full scale emergency disaster drills. For more details on these proposed requirements, see the discussion under proposed § 139.301, Records; § 139.303, Personnel; and § 139.327, Airport emergency plan.

A significant change for operators of proposed Class II and IV airports would be the requirement to include in the ACM a description of the procedures and equipment used for complying with the ARFF standards of proposed §§ 139.317 and 139.319. While these airports provide for ARFF coverage, the level of coverage may not meet standards prescribed under existing §§ 139.317 and 139.319. The FAA proposes to require operators of Class II and IV airports to include ARFF procedures in their ACM, as specified in subpart D, and comply with at least Index A ARFF requirements. Airport operators could petition for an exemption from some or all ARFF requirements under proposed § 139.321, Aircraft rescue and firefighting: Exemptions, provided conditions prescribed in proposed § 139.321 are met.

Unlike Class IV airports, Class II airports would serve both unscheduled operations of large air carrier aircraft and scheduled small air carrier aircraft. As such, the FAA proposes additional safety requirements appropriate for Class II airports. These airports would most likely serve more total air carrier operations than proposed Class IV airports and would be required to comply with additional requirements. These additional requirements would be addressed in the ACM as follows:

1. Procedures for avoidance of interruption, or failure during construction work, of utilities serving facilities or navaids that support air carrier operations;

2. A snow and ice control plan as required under proposed § 139.313;

3. Procedures for controlling ground vehicles as required under proposed § 139.331;

4. Procedures for obstruction removal, marking, or lighting as required under proposed § 139.333;

5. Procedures for protection of navaids as required under proposed § 139.335;

6. A wildlife hazard management plan as required under proposed § 139.339; and

7. Procedures for identifying, marking, and reporting construction and other unserviceable areas as required under proposed § 139.343.

Class III airports would be newly certificated under this proposal. As such, operators of these airports would be required to develop an ACM. For some operators, this requirement would be minimal because it would only require documenting existing procedures. Other Class III airport operators would be required, for the first time, to develop new procedures. Still others would be required to establish manuals based on a combination of new and existing procedures.

Under new paragraph (b), proposed Class III airport operators would be required to include in their ACM a description of the following procedures and equipment—

1. Lines of succession of airport operational responsibility;

2. Each current exemption issued to the airport from the requirements of this part;

3. Limitations imposed by the Administrator;

4. A grid map or other means of identifying locations and terrain features on and around the airport which are significant to emergency operations;

5. The location of each obstruction required to be lighted or marked within the airport's area of authority;

6. A description of each movement area available for air carriers and its safety areas and each road described in § 139.319(k) of this part that serves it;

7. Procedures for avoidance of interruption, or failure during construction work, of utilities serving facilities or navaids that support air carrier operations;

8. A description of the system for maintaining records as required under § 139.301 of this part;

9. A description of personnel training as required under § 139.303 of this part;

10. Procedures for maintaining the paved areas as required under § 139.305 of this part;

11. Procedures for maintaining the unpaved areas as required under § 139.307 of this part;

12. Procedures for maintaining the safety areas as required under § 139.309 of this part;

13. A sign plan depicting the runway and taxiway identification system and location and inscription of the signs as required under § 139.311 of this part;

14. A description of, and procedures for maintaining, the marking, signs, and lighting systems as required under § 139.311 of this part;

15. A snow and ice control plan as required under § 139.313 of this part;

16. A description of the facilities, equipment, personnel, and procedures for meeting the rescue and firefighting requirements in accordance with §§ 139.317 and 139.319 of this part;

17. A description of any approved exemption from the rescue and firefighting requirements as authorized under § 139.321 of this part;

18. Procedures for handling fuel, lubricants and oxygen required under § 139.323 of this part;

19. A description of, and procedures for maintaining, the traffic and wind direction indicators as required under § 139.325 of this part;

20. An emergency plan as required under § 139.327 of this part;

21. Procedures for conducting the self-inspection program as required under § 139.329 of this part;

22. Procedures for controlling ground vehicles as required under § 139.331 of this part;

23. Procedures for obstruction removal, marking, or lighting as required under § 139.333 of this part;

24. Procedures for protection of navaids as required under § 139.335 of this part;

25. A description of public protection as required under § 139.337 of this part;

26. A wildlife hazard management plan as required under § 139.339 of this part;

27. Procedures for airport condition reporting as required under § 139.341 of this part;

28. Procedures for identifying, marking, and reporting construction and other unserviceable areas as required under § 139.343 of this part; and

29. Other requirements that the Administrator finds is necessary to ensure safety in air transportation.

While operators of proposed Class III airports would be required to include many of the same elements in their certification manual as Class I and II airports, the FAA can provide relief from some of these requirements that are too operational or economically burdensome. The operators of Class III airports may petition for an exemption from some or all ARFF requirements, and relief is proposed from certain sign and emergency drill requirements.

In addition, this section would specify that operators of all proposed classes of airport would be required to develop a sign plan as part of their ACM that shows the location on the airport and inscription of each sign required by § 139.311(b). During a review of airport sign systems [52 FR 44276, November 18, 1987; and 53 FR 40842, October 18, 1988], the FAA found that planning and diagramming appropriate signs and their location avoided unnecessary sign purchases or improper sign locations. Accordingly, the FAA believes the requirement for a sign plan would be beneficial to all certificated airports and that most currently certificated airports comply with this proposed requirement.

The following tables list both current part 139 requirements and proposed subject requirements that would be applicable to each airport classification should the FAA adopt this proposal. Proposed requirements would be in addition to current requirements as revised, unless otherwise noted in the table.

A. Current and Proposed Requirements for Class I Airports

Current requirements

Proposed requirements

1. Personnel provisions

A recordkeeping system and new personnel training standards.

2. Paved and unpaved surfaces

Unchanged.

3. Safety areas

Unchanged.

4. Marking, lighting and signs

Unchanged.

5. Snow and ice control plan

Unchanged.

6. ARFF

New recurrency training, fire extinguishing agent and HAZMAT response standards, and increase frequency of ARFF coverage (where ARFF is not provided for small air carrier operations).

7. HAZMAT handling/storage

Standards for air carrier fueling operations, and additional fuel fire safety and personnel training standards.

8. Traffic/wind indicators

New supplemental wind cone/segmented circle standards.

9. Airport emergency plan (AEP)

New requirement to plan for fuel storage fires.

10. Self-inspections

New training requirements for inspection personnel.

11. Ground vehicle operations

Unchanged.

12. Obstructions

Unchanged.

13. Navaids

Unchanged.

14. Public protection

Unchanged.

15. Wildlife hazard management

New wildlife strike reporting, hazard assessment, and management plan standards.

16. Airport condition reporting

New notification standard.

17. Construction/unserviceable areas

Unchanged.

B. Current and Proposed Requirements for Class II Airports

Current requirements

Proposed requirements

1.

New requirements for a recordkeeping system and personnel training.

2. Paved and unpaved surfaces

Unchanged.

3. Safety areas

Unchanged.

4. Marking, lighting and signs

Unchanged.

5.

New requirement for snow and ice control plan.

6. ARFF (negotiated standard)

New ARFF standards per proposed 139.315-.321).

7. HAZMAT handling/storage (negotiated standard)

New HAZMAT handling/storage standard (per proposed 139.323).

8. Traffic/wind indicators (negotiated standard)

New traffic/wind indicators standard (per proposed 139.325)

9.

New requirement for AEP (no triennial exercise required).

10. Self-inspections (negotiated standard)

New self-inspections standard (per proposed 139.329).

11.

New requirement for ground vehicle operations.

12.

New requirement for obstructions.

13.

New requirement for Navaids.

14.

New requirement for public protection.

15.

New requirement for wildlife hazard management.

16. Airport condition reporting (negotiated standard)

New airport condition reporting standard (per proposed 139.341).

17.

New requirement for construction/unserviceable areas.

C. Current and Proposed Requirements for Class III Airports

Current requirements

Proposed requirements:

1.

A recordkeeping system and personnel training.

2.

Paved and unpaved surfaces.

3.

Safety areas.

4.

Marking, lighting and signs.

5.

Snow and ice control plan.

6.

ARFF.

7.

HAZMAT handling/storage.

8.

Traffic/wind indicators.

9.

AEP (no triennial exercise required).

10.

Self-inspections.

11.

Ground vehicle operations.

12.

Obstructions.

13.

Navaids.

14.

Public protection.

15.

Wildlife hazard management.

16.

Airport condition reporting.

17.

Construction/unserviceable areas.

D. Current and Proposed Requirements for Class IV Airports

Current requirements

Proposed requirements

1.

New requirement for a recordkeeping system and personnel training.

2. Paved and unpaved surfaces

Unchanged.

3. Safety areas

Unchanged.

4. Marking, lighting and signs

Unchanged.

5.

6. ARFF (negotiated standard)

Unchanged.

7. HAZMAT handling/storage (negotiated standard)

Unchanged.

8. Traffic/wind indicators (negotiated standard)

Unchanged.

9.

New requirement for an AEP (triennial exercise not required).

10. Self-inspections (negotiated standard)

Unchanged.

11.

12.

13.

14.

15.

16. Airport condition reporting (negotiated standard)

Unchanged.

17.

Section 139.205 Amendment of Airport Certification Manual

Under this proposal, existing § 139.205, titled “Contents of airport certification manual,” would be moved to proposed § 139.203. Existing § 139.217, titled “Amendment of Airport Certification Manual or Airport Certification Specifications,” would be moved to proposed § 139.205 and retitled. Existing § 139.217 specifies procedures for amending the ACM or the ACS.

Minor editorial clarifications are proposed to existing § 139.217, but existing amendment procedures and requirements would be unchanged. The title of the section would be revised to delete the term “Airport Certification Specifications.” Also, references to the Administrator have been changed to Associate Administrator for Airports. Action on petitions made under this section would be delegated to the Associate Administrator for Airports.

In addition, amendment procedures specified in existing paragraph (d) would be revised. Currently the FAA may initiate action to amend an ACM, but there is no time period specified when the certificate holder will be notified of the disposition of a proposed amendment. Under new paragraph (d), the certificate holder would be notified within 30 days after receipt of the notification as to whether the amendment has been adopted or rescinded.

Subpart D—Operations

Section 139.301 Records

Under this proposal, existing § 139.301, titled “Inspection authority,” would be moved to proposed subpart B and consolidated with existing language of § 139.105 to create a single section titled “Inspection authority” (see discussion under § 139.105, Inspection authority). Proposed § 139.301, titled “Records,” would be new and be applicable to all part 139 airports.

With the addition of new airports to the certification process, the FAA believes it is necessary to clarify certificate holders' recordkeeping responsibilities. While many certificated airports already keep records to show compliance with part 139, this proposed amendment would ensure more consistent recordkeeping and require that the FAA be given access to such records.

New paragraph (a) would stipulate that the certificate holders would make available to FAA inspectors records required under part 139 in a manner to facilitate their monitoring of an airport's compliance with part 139.

Proposed new paragraph (b) would require that a certificate holder make and maintain records of each scheduled

or unscheduled operation of large air carrier aircraft and scheduled operations of small air carrier aircraft, if the airport serves less than 10,000 annual air carrier operations during the previous 24 consecutive calendar months. This information will assist the FAA in determining whether the airport operator should continue to hold an AOC.

The FAA does not currently collect data on air carrier operations from airports with less than 10,000 annual operations, nor is data collected on unscheduled air carrier operations. Without this data, it is difficult for the FAA to properly allocate resources at airports serving small or unscheduled air carrier aircraft. The FAA does not believe this requirement is unduly burdensome as many airport operators already track air carrier operations for planning purposes and collecting user fees.

Proposed paragraph (c) would require the certificate holder to maintain any additional records that the Administrator may require. This paragraph also identifies some new and existing recordkeeping requirements contained in proposed part 139.

Section 139.303 Personnel

Existing § 139.303 requires certificate holders to maintain sufficient qualified personnel necessary to comply with the requirements of part 139. Under this proposal, this section would be revised to include additional requirements, organized into four new paragraphs. The requirements of this revised section would be applicable to all part 139 airports.

With the addition of new airports to the certification process, the FAA proposes to clarify in new paragraphs (a) and (b) a certificate holder's responsibilities to train and equip personnel performing duties required under the proposed part 139. This would include duties performed by airport personnel necessary to ensure the safe and efficient operation and maintenance of the airport. While many existing part 139 airports must comply with existing requirements of § 139.303, this proposal would for the first time stipulate that certificate holders must ensure that their personnel have the available resources needed to properly perform their duties. For example, a certificate holder would be required to provide personnel responsible for the upkeep of runway lighting with any necessary electrical supplies and tools, as well as provide access to pertinent sections of the ACM, and appropriate AC's.

New paragraph (c) proposes that the certificate holder develop a personnel training program to ensure that all personnel have the specific knowledge to perform their required duties at their airport and can perform such duties. Similar to training required for ARFF personnel, this training would be required when personnel first assume their duties and again on a reoccurring basis, as specified in the ACM.

New paragraph (d) would require the certificate holder to maintain records of training given to personnel, as required under this new section. Training records for each individual would have to be kept for each employee a minimum of two years after completion of the training to ensure these records are available for the FAA's annual inspection. The FAA has found that annual ARFF training records currently required have benefited the FAA and certificate holders in monitoring the quality and effectiveness of training. The FAA believes it would be beneficial to require training records of other employees that have duties prescribed in the ACM.

Section 139.305 Paved Areas, and Section 139.307 Unpaved Areas

Under this proposal, existing §§ 139.305 and 139.307 would remain virtually unchanged. These sections prescribe standards for maintaining and repairing paved and unpaved areas.

The term “Airport Certification Specifications” would be deleted to reflect proposed certification changes, and language stating specific series numbers within the AC system would be changed to a general reference to the AC system.

Further, existing § 139.305(a)(1) would be modified by deleting the terms “full strength” and “shoulder.” The terms “full strength” and “shoulder” have caused confusion as to what areas surrounding movement areas to apply the 3-inch abutting surface limitation. To minimize damage to an aircraft that inadvertently leaves a runway, taxiway or other movement areas, this standard ensures that the edges of such pavement do not exceed more than 3 inches in height than the surrounding areas. This change clarifies that the standard is applicable to any area surrounding pavement used by air carrier aircraft, regardless of how these areas are used, or these areas' condition, strength, or composition.

Currently, all airports certificated under part 139 must comply with the provisions of §§ 139.305 and 139.307. In addition, proposed manual requirements (proposed § 139.205) would require operators of newly certificated airports to develop procedures for maintaining paved and unpaved areas, as required under these sections. Both the FAA and the ARAC Commuter Airport Certification Working Group agree that airports serving scheduled operations of small air carrier aircraft should be required to maintain paved and unpaved areas as prescribed by these sections. Paved and unpaved areas include loading aprons, parking areas, taxiways, and runways. The deterioration of pavements and other areas must be limited to ensure that these areas adequately support air carrier aircraft operations.

The requirements for paved and unpaved areas should not prove a hardship on proposed Class III airports. As mentioned earlier, many of these airports have received Federal funding for paving improvements or new construction (see discussion of Regulatory Evaluation). These airports already maintain paved areas in a manner authorized by the Administrator in order to comply with grant assurances (see discussion of proposed § 139.109, Duration of certification). Pavement rehabilitation and expansion projects are eligible for further Federal funding and may be eligible for additional state or local funding.

Section 139.309 Safety Areas

Existing § 139.309 prescribes standards for the establishment and maintenance of a safety area for each runway and taxiway available for air carrier use. Under this proposal, this section would remain the same, except for minor editorial changes to paragraphs (a) and (c). The requirements of this revised section would be applicable to all part 139 airports, including proposed Class III airports.

A safety area is a defined area surrounding a runway or taxiway that is prepared, or suitable, for reducing the risk of damage to aircraft in the event an aircraft undershoots, overshoots, or deviates from a taxiway or runway. Establishing a safety area may require filling of culverts, grading, and compacting the ground to remove depressions or high spots. Lights and signs may be reinstalled on frangible mountings. A well-maintained safety area can prevent injuries to passengers and limit damage to aircraft that depart from paved surfaces. The safety area would allow the aircraft to come to a rest on a graded, obstacle free surface. Safety areas also allow emergency response vehicles to more quickly reach troubled aircraft.

The language of existing paragraph (a) would be revised to require that certificate holders ensure runway safety

areas are maintained in accordance with the standards of this section, unless otherwise approved in the ACM.

Dates listed in existing paragraphs (a)(1) and (2) that “grandfather” existing safety areas would remain effective. These dates were adopted when part 139 was revised in 1987 (52 FR 44276, November 18, 1987.) Prior to 1987, many airport operators invested resources to develop safety areas before standardized guidelines were established. Further, physical limitations of airports resulted in establishment of some safety areas that did not meet the standard due to local circumstances. For example, available solid ground around runways located adjacent to bodies of water may have been inadequate to establish a safety area that meets the required dimensions.

Since 1988, the FAA has required any renovation or construction of safety areas to meet the requirements of § 139.309 at most airports that would be effected by this proposed rule, including proposed Class III airports. Any newly certificated airport under this proposal that has renovated or constructed its safety areas since 1988 could apply for an exemption under proposed § 139.111 if its safety areas do not comply with the requirements of this section.

Paragraph (c) would be revised to make a general reference to the availability of the AC system.

Section 139.311 Marking, Signs, and Lighting

Existing § 139.311, titled “Marking and lighting,” specifies standards for runway and taxiway markings, signs, and lighting. Under this proposal, this section would be retitled and clarified. In addition, new paragraphs (b) and (g) would be added. The marking and lighting requirements would be revised to correspond to proposed § 139.203 requiring all operators of certificated airports to comply with this section.

The addition of the word “signs” to the title of this proposed section reflects proposed changes to this section that would separate marking, signs, and lighting requirements into three distinct paragraphs. Paragraph (a) would contain marking requirements, new paragraph (b) would specify sign requirements, and paragraph (c) would detail movement area lighting requirements.

Revised paragraph (a) would contain existing marking requirements, with a minor clarification concerning taxiway edge markings. In addition, the word “runway” would be deleted from the term “runway holding position markings” to permit special operations that require holding position markings other than those prior to the runway. To accommodate such special aircraft operations, the FAA proposes to delete the word “runway” from both the phrase “runway holding position markings” in proposed paragraph (a) and the phrase “runway holding position signs” in proposed paragraph (b).

New paragraph (b) would include sign requirements currently found in § 139.311(a) and specify signs that must be internally illuminated. Paragraph (b)(2) would require proposed Class I, II, and IV airports operators to internally illuminate taxiing route signs, holding position signs, and ILS critical area signs. Paragraph (b)(3) would require operators of proposed Class III airports to internally-illuminate only holding position and ILS critical area signs.

Due to cost associated with installing and maintaining internally-illuminated signs, the majority of the ARAC Commuter Airport Certification Working Group recommended use of retro-reflective runway signs (signs that reflect light back, similar to signs used on interstate highways) for runways not equipped with lighting. Internally-illuminated signs would be appropriate for runways that are equipped with lighting. The working group report recognized the cost to install internally-illuminated signs and suggested use of these signs only on runways that have a power source in place. The initial cost to supply electrical power to taxiways and/or runways was viewed as relatively high, and the working group hoped this approach would economize airport resources.

While the majority of the working group recommended retro-reflective signs identifying taxiing routes, representatives of ALPA recommended that newly certificated airports (proposed Class III airports) install internally-illuminated signs on taxiing routes where edge or centerline lighting exists. ALPA opposes retro-reflective taxiway signs because it believes that retro-reflective signs may not be visible to pilots operating aircraft of varying size and configurations. Conversely, the majority of members believe that aircraft with fewer than 31 passenger seats (typically used at Class III airports) are lower to the ground, thereby validating use of retro-reflective signs. ALPA further argued that similar requirements for runway and taxiway signs would ensure standardization and, with the gradual conversion to internally illuminated signs, would present a minimal economic burden, noting that signs are eligible for Federal funding.

The FAA disagrees with ALPA's conclusion that use of internally-illuminated signs will present minimal impact on airports. While improvements to taxiway and runway signs are eligible for Federal funding, such improvements may not receive funds. Further, requiring installation of specific equipment on the assumption that the equipment is eligible for funds through the AIP would be misleading. AIP funds are allocated on a priority basis, and airport sign improvements would compete with other airport improvements and safety projects on a nationwide basis. Moreover, AIP funds do not cover all of an airport's costs local communities provide some matching funds.

However, the FAA is concerned about ALPA's contention that retro reflective signs may not be visible to all air carrier pilots because of differences in aircraft configurations and the location of taxi lights, and would like to use this rulemaking to invite comments on this issue. FAA also requests comments, including economic and operational data, on whether or not the installation of unlighted retro-reflective signs would provide an adequate sign system for Class III airports.

The term “unless otherwise authorized by the Administrator” also would be included in new paragraph (b) to provide for those instances where an airport has a runway that does not have edge or in-pavement lighting, thus a suitable power source may not be available to illuminate signs. In such cases, the FAA would work with the airport to develop acceptable alternative signs until funding is available for installing or improving power for runway lights and signs.

New paragraph (c) would contain existing lighting requirements for aircraft operations currently found in existing § 139.311(b). The word “darkness” would be replaced with the word “night,” which is defined in 14 CFR part 1. Special criteria also would be included to address the unique environment of Alaska.

Also, references to 14 CFR part 77 concerning obstruction would be deleted. Part 77 is being revised and may be reorganized. New paragraph (c)(5) of proposed § 139.311 would require the marking and lighting of objects determined by the FAA to be an obstruction.

The phrase “authorized by the Administrator” also would be added to existing language of proposed paragraphs (a), (b), and (c). This change would ensure that the requirements of this section are implemented in a manner satisfactory to the FAA. This change corresponds to those in proposed § 139.7 (see discussion under

§ 139.7 Methods and procedures for compliance).

In addition, language in paragraphs (a), (b), and (c) pertaining to lowest minimums authorized for a runway would be modified. This revised language would clarify that the FAA authorizes landing and takeoff minimums for runways. This does not change how such minimums are currently determined; the revised language clarifies that FAA is responsible for making such determinations.

With changes to other paragraphs in this section, existing paragraph (c) would become new paragraph (d) and continue to require certificate holders to properly maintain marking, sign and lighting systems. Existing (d), requiring certificate holders to prevent light interference with air traffic control and aircraft operations, would become new paragraph (e). Consequently, existing paragraph (e) would become new paragraph (f) and continue to specify that advisory circulars (AC's) contain marking, sign, and lighting standards that are acceptable to the Administrator. Existing paragraph (f) would be deleted as it addresses an implementation date that has already passed.

A new paragraph (g) proposes a compliance date for marking and lighting requirements by operators of proposed Class III airports. These airport operators would be provided adequate time to develop a sign plan, order, and take delivery of signs, and install signs required by this part. Operators of proposed Class II and IV airports currently holding an LAOC should already comply with this section's requirements.

Section 139.313 Snow and Ice Control

This proposal would make minor modifications to the existing standards of § 139.313, titled Snow and ice control. As proposed, Class I airport certificate holders would continue to implement their existing snow plans, and operators of proposed Class II and III airports would be required to develop snow and ice control plans, as appropriate.

Existing § 139.313 requires operators of airports serving scheduled operations of large air carrier aircraft to develop and implement snow and ice control plans, if the airport is located in an area where snow and icing conditions regularly occur. Snow and ice plans include procedures for removal and control of snow and ice accumulations and notification to air carriers when movement areas are unusable due to snow and ice. No changes are proposed to these requirements.

In the revised paragraph (a), the term “regularly” would be deleted and new language added to clarify that the FAA will determine which airports require snow and ice control plans. The term “regularly” is too vague and difficult to further define.

Proposed § 139.313(b)(2) would be modified. This paragraph prescribes the standard for positioning snow off movement areas. This proposal would not change this standard, but would delete the redundant term “full strength.” This term “full strength” is unnecessary as proposed § 139.3 defines movement areas as those areas used by aircraft to taxi and land. To function as such, movement areas must have the capability to support the weight of the aircraft using these surfaces—a surface condition described as full strength.

In addition, references to airport condition reporting requirements in paragraph (b) would be updated to correspond to new section numbering. Paragraph (c) also would be modified to reference generically to the AC system rather than specific series number.

The ARAC Commuter Airport Certification Working Group's report contained a recommendation that Class II and III airports should be required to remove snow and ice. The working group suggested minor modifications to the rule language that would limit the requirement to remove snow and ice to times just prior to air carrier operations. The group recommended deletion of the requirement that snow and ice be removed promptly. The FAA disagrees. Continuous and prompt removal of snow and ice ensures safe airport conditions in hazardous weather conditions. Failure to promptly remove snow and ice from movement areas could make removal of accumulations just prior to air carrier operation more difficult.

Sections 139.315-139.321 Aircraft Rescue and Firefighting (General Discussion)

Existing part 139 has three sections dedicated to aircraft rescue and firefighting (ARFF) requirements. This proposal would revise these three sections to include new requirements and reflect current industry practices. In addition, a fourth ARFF section is proposed that would specify procedures for airport certificate holders to request an exemption from ARFF requirements.

This proposal also would require that

all

airports certificated under part 139 provide appropriate ARFF coverage meeting at least minimum ARFF requirements (Index A), subject to the limited exemption discussed below. Proposed changes to ACM requirements (see discussion of proposed § 139.203, Contents of airport certification manual) would require all certificated airports to include procedures in their ACM for complying with proposed ARFF requirements appropriate to the air carrier aircraft and operation served.

Currently, only airports serving scheduled operations of large air carrier aircraft are required to comply with all of part 139 ARFF requirements. Under existing § 139.321(b)(11), airports serving unscheduled operations of large air carrier aircraft (airports holding an LAOC) are required only to provide for “emergency response to aircraft rescue and firefighting needs.” This means that airports holding an LAOC must provide for ARFF coverage but such coverage does not have to meet prescribed part 139 ARFF requirements. The FAA determines ARFF requirements at these airports on a case-by-case basis. While the FAA uses part 139 standards as a benchmark, the level of this coverage varies depending on the air carrier operations served and the availability of local resources.

To standardize ARFF at certificated airports, the FAA proposes that all certificated airports serving both scheduled and unscheduled operations be required to comply with all ARFF requirements. However, requiring all airports to comply with the standards of this revised section may pose a substantial cost for airports that do not currently provide at minimum ARFF coverage (Index A), or do so only to cover an occasional unscheduled air carrier flight. This would include both currently certificated airports and airports that would be newly certificated if this proposal is adopted.

The FAA has provided financial and technical support to help some airports holding an LAOC comply with part 139 ARFF requirements, particularly for the purchase of ARFF equipment. As a result, many airports holding a LAOC already comply with most of the ARFF requirements. However, the FAA recognizes that these airports typically are located in smaller communities that have limited resources and that the sporadic nature of unscheduled air carrier operations often makes it cost prohibitive for such communities to provide the same level of ARFF coverage provided by airports serving scheduled large air carrier aircraft.

Accordingly, the FAA proposes to establish procedures to exercise its statutory authority to provide limited exemptions for certain airports from some or all prescribed ARFF requirements on a case-by-case basis.

The issue of ARFF proved to be the most contentious for the ARAC

Commuter Airport Certification Working Group. The group was not able to reach a consensus on the level of ARFF coverage appropriate for airports serving small air carrier aircraft. While the majority of the working group agreed that ARFF equipment should meet minimum ARFF coverage required under part 139 (Index A), no agreement was reached for stationing ARFF personnel and equipment on the airport, or requiring a 3-minute ARFF response.

The working group's greatest concern was over labor and training costs associated with ARFF requirements. The working group concluded that many of the communities serving small air carrier operations could not afford to provide the same level of ARFF services required of airports serving large air carrier operations, even if Federal funds were made available to assist in the purchase of ARFF equipment. The majority of the members of the working group recommended that operators of small airports work with local firefighting agencies to arrange for emergency services and incorporate such arrangements into the airport's emergency plan.

The majority of the working group also concluded that there was a lack of accident data to support on-airport ARFF at smaller facilities. The working group reviewed the National Aviation Safety Data Analysis Center's (NASDAQ) collection of NTSB reports for all part 135 scheduled airplane accidents and incidents that occurred on airports between 1983 and 1996. The group discovered 15 on-airport accidents involving small air carriers that resulted in post crash fires. A total of 38 fatalities occurred as a result of these accidents. With the exception of one accident resulting in fatalities, all fatalities were the result of the aircraft impact, not the subsequent fire.

The exception is the crash of Northwest Airlink Flight 2268, a CASA-212 commuter aircraft, at the Detroit Metropolitan Airport on March 4, 1987. The Detroit Metropolitan Airport is a part 139 certificated airport with the most comprehensive ARFF capabilities (Index E). A rapid intervention ARFF vehicle was at the crash scene within one and one-half minutes of the alarm from the control tower, and the fire was extinguished within two minutes of the first alarm. Before ARFF services could arrive, a quick and intense post crash fire killed nine aircraft occupants. Ten occupants survived, by exiting the aircraft prior to the secondary fire.

The working group did not consider the November 1996 commuter accident at Quincy, Illinois, in its review because the NTSB had not concluded its investigation at that time.

The Air Line Pilots Association (ALPA) expressed a minority position for one level of safety and stringent ARFF requirements at all certificated airports regardless of size of aircraft serving the airport. ALPA favored a 3-minute test response that is currently required of airports receiving scheduled operations of large air carrier aircraft, and offered suggestions for providing personnel needed for ARFF response. Among others, ALPA suggested that airport operators cross-train their employees (or tenant employees) to perform ARFF duties, or that the local community site a fire station on the airport. ALPA subsequently provided a position document that is available in the docket.

The FAA is not opposed to ALPA's position that ARFF coverage be provided at airports served by small air carrier aircraft. Current part 139 and this proposal permit the use of existing airport employees to perform ARFF duties so long as the provisions of part 139 are met. With FAA approval, an airport operator could arrange to have part, or all, of its ARFF responsibilities performed by an air carrier or fixed base operator (FBO) so long as the requirements of this part and the airport's certification manual are met.

However, ALPA's position on a standard 3-minute test response is impractical. Most local volunteer fire departments would not have volunteers present for every air carrier operation. Similarly, locating a fire station on the airport can mean that, during air carrier operations, firefighters would not be available to provide emergency services elsewhere in the community.

In connection with this rulemaking, the FAA is considering a clarification of agency policy on the use of airport revenue to promote the availability of ARFF services at small airports. Generally, a non-aeronautical municipal use of airport property must be charged a fair market rental rate for the airport to comply with grant assurances that require the airport to maintain a rate structure that makes it as self-sustaining as possible (see discussion of § 139.109 Duration of certificate). However, a municipal fire station on airport property may receive a reduction in rent proportional to the airport-related purpose and use of the station. In connection with the adoption of proposed ARFF requirements for airports serving small air carrier aircraft, the FAA would consider this reduction to apply to a municipal fire station located on a Class II, III, or IV airport when the municipal station is an essential element of the local agreement the airport uses to meet its ARFF obligations under part 139.

Since the ARAC submitted its report on the certification of commuter airports, the NTSB announced its findings on the commuter aircraft accident in Quincy, Illinois. The accident involved the runway collision of a United Express Flight 5925, a Beech 1900C commuter aircraft, and a Beech King Air, N1127D, during the landing sequence of the United Express and the take off of the King Air from Quincy Municipal Airport. The Quincy Municipal Airport has a limited airport operating certificate and only provides ARFF coverage during large air carrier operations. At the time of the accident, there were no large air carrier aircraft operations and ARFF services were not on site. All ten passengers and two crewmembers aboard Flight 5925 and the two occupants on the King Air were killed as the result of post-crash fires.

The NTSB found that the speed with which the fire enveloped the King Air, and the intensity of the fire, precluded survivability of the occupants. The occupants of the Beech 1900C did have the opportunity to escape but could not open external doors that had been damaged. The NTSB concluded that lives might have been saved had on-airport ARFF protection been required. However, the board recognized the economic difficulties on-airport ARFF requirements would place on smaller communities. In this regard, the NTSB recommended that the FAA develop ways to fund ARFF protection at airports serving scheduled passenger operations in aircraft with more than 10 seats.

Section 139.315 Aircraft Rescue and Firefighting: Index Determination

Airports certificated under part 139 that serve

scheduled

air carrier operations with more than 30 seat aircraft must provide ARFF coverage that is appropriate to the size of aircraft using the airport. Existing § 139.315 establishes criteria for determining the proper ARFF coverage. Requirements for this coverage are divided into five categories, or indexes, based on the length of the longest air carrier aircraft that departs the airport at a certain frequency. Index A prescribes the minimum ARFF standards (type of extinguishing agent, truck capacity, etc.) that an airport must provide during operations of air carrier aircraft less than 90 feet in length. Air carrier aircraft with 10-30 seats used in scheduled passenger service are typically less than in 90 feet in length.

Under this proposal, clarifications would be made to the requirements of existing § 139.315. Existing paragraph (c)(1) and (c)(2) would be combined into a single paragraph.

The current format of this paragraph has resulted in (c)(1) and (c)(2) being misinterpreted and airports complying with lower ARFF index requirements than intended.

A certificated airport serving scheduled air carrier operations must comply with the ARFF Index that corresponds to the largest aircraft as long as there are five or more average daily departures of that type of aircraft. However, confusion exists when the largest aircraft serving an airport has less than five daily departures. In such cases, a certificated airport must meet the next lower ARFF index requirements for the largest air carrier aircraft serving the airport, regardless on number of average daily departures.

For example, if an airport serves 10 daily departures of Index A aircraft, three daily departures of Index B aircraft, and four daily departures of Index C aircraft, the FAA intends for this airport to provide at least Index B ARFF coverage. Index B ARFF coverage would also be required at an airport receiving four daily departures of Index A aircraft, four daily departures of Index B aircraft, and three daily departures of Index C aircraft. The existing rule language has resulted in the incorrect interpretation that Index A ARFF coverage would be appropriate in both examples because daily departures were used as the determining factor rather than the largest aircraft serving the airport. When the largest aircraft serving a certificated airport has less than five daily departures, then aircraft size would determine the ARFF index.

The FAA also proposes revisions to this section to emphasize that in all circumstances, the minimum ARFF index will be Index A.

Section 139.317 Aircraft Rescue and Firefighting: Equipment and Agents

Existing § 139.317 prescribes standards for ARFF equipment and fire extinguishing agents. The FAA proposes revisions to this section to reflect changes made to the production of fire extinguishing agents.

The FAA proposes to add the phrase “unless otherwise authorized by the Administrator” to this section to provide relief to airports waiting for Federal funds to purchase adequate equipment, or to address other local circumstances that may require temporary use of alternative equipment or extinguishing agents. Long-term relief from the standards of this section would be considered under proposed § 139.321, Aircraft rescue and firefighting: Exemption.

In addition, the term “clean agent” would be added to this section. The term defines a new type of aircraft fire extinguishing agent that an airport operator could use to comply with this section, and as noted earlier, is used by the firefighting community to describe a category of fire extinguishing agents that replace halon 1211.

Under existing § 139.317, halon 1211 is specified as one of the fire extinguishing agents that an airport operator can use. However, chlorofluorocarbon chemicals, including halon 1211, have been identified as a stratospheric ozone depleter. The United States Environmental Protection Agency (EPA) banned the production of halon 1211 on January 1, 1994. Airport operators currently using halon 1211 will be required by the EPA to switch to authorized agents when their stockpiles are depleted and may only use halon 1211 during actual aircraft emergencies.

Under this proposal, most of existing § 139.317(i) would be deleted. The FAA proposes to remove references to specific standards for extinguishing agent substitutions and place these in an advisory circular. Only language allowing the use of alternate extinguishing agents authorized by the Administrator would be retained.

The FAA also proposes to remove language no longer needed in this section that provided relief to certain airport certificate holders whose ARFF vehicles were unable to comply with all the requirements of this section at the time of the regulation's last revision (November 1987). Since the 1987 revision, the FAA has funded through the Airport Improvement Program the purchase and rehabilitation of ARFF vehicles, and noncompliant vehicles have been replaced. However, the FAA recognizes that airports newly certificated (proposed Class III airports) may be using ARFF vehicles that do not comply fully with the requirements of this section. The exemption process of proposed § 139.321 would enable the FAA to consider relief from this section's requirements.

The FAA proposes a 2-year timeframe for those airports required for the first time to comply with the standards of this section (proposed Class II, III and IV airports). The proposed compliance dates should allow these airports adequate time to acquire funding for, and purchase of, ARFF equipment. Approximately 40 airports (both certificated and non-certificated) would have to obtain additional ARFF equipment. The FAA would consider a time extension for airports unable to comply within this 2-year timeframe.

Section 139.319 Aircraft Rescue and Firefighting: Operational Requirements

Existing § 139.319 prescribes standards for the training of ARFF personnel; ARFF vehicle marking, lighting, and readiness; and emergency access roads. This section also establishes criteria for a certificate holder to make adjustments to ARFF coverage to correspond to changes in air carrier operations. Currently, only airports serving scheduled operations of large air carrier aircraft are required to comply with § 139.319. Under this proposal, all classes of airports would be required to comply with the requirements of this revised section.

Existing § 139.319 would be revised to reflect current rescue and firefighting practices. Also, it would address a petition for rulemaking made by the Air Transport Association of America (ATA). As the result of these proposed changes, many existing paragraphs would be given new paragraph designations and titles to ensure a consistent format throughout the section.

Specifically, existing paragraph (g) would be moved to new paragraph (l) and titled “Methods and procedures.” This change would ensure that all references to compliance methods and procedures are consistently located at the end of each section. All references to specific series numbers within the AC system would be deleted. Instead, this revised paragraph would make a general reference to the AC system.

Several changes also would be made throughout new paragraph (h) (existing paragraph (i)) for clarity and to reflect changes in terminology used to describe fire extinguishing agents (see discussion of proposed § 139.317).

In addition, proposed paragraph (i) would contain existing requirements of paragraph (j), with several modifications. Language would be included in new § 139.319(i)(2) to clarify that rescue and firefighting personnel must be trained before initial performance of duties and, at a minimum, must receive annual recurrency training.

Also, the FAA proposes to clarify the frequency of training required for rescue and firefighting personnel. Many of the subject areas required under existing paragraph (j) (proposed new paragraph (i)) necessitate ongoing training, and ARFF personnel would not be expected to maintain currency with only a once-a-year course. Most ARFF organizations have a continuous training program

throughout the year. The FAA supports this continuous training approach and proposes a 12-month recurrent training requirement as the benchmark for the minimum training required.

The FAA also proposes, in new paragraphs (i) and (j), to require the use of hazardous material guidance. In August 1990, the ATA petitioned the FAA to amend part 139 ARFF procedures related to hazardous materials incidents. In its petition, ATA expressed concern that without proper training and guidance, ARFF personnel could take incorrect action in response to a hazardous materials incident that might endanger both the emergency crews and the general public. At that time, ATA stated that ARFF crews were relying solely on hazardous materials emergency response guidance required to be carried aboard the aircraft.

ATA recommended that § 139.319 be amended to require ARFF crews to be equipped with, and trained in the use of, the North American Emergency Response Guidebook published by Transport Canada, U.S. Department of Transportation, and the Secretariat of Communications and Transportation of Mexico. The ATA stated that the guidebook would promote a better understanding of ground emergency response and alleviate the need for ARFF personnel to be solely dependent of on-board information, which may or may not be available during an emergency, and may not be appropriate to a ground-based incident.

In response, the FAA published a summary of the petition in the

Federal Register

(55 FR 39299, September 26, 1990), and received 14 comments from airport operators, ATA and-ALPA. Most of the commenters agreed with the substance of the petition and recognized the value of providing ARFF personnel with guidance and training to properly respond to hazardous materials incidents. Several airport operators disagreed with ATA because many airports already equip ARFF personnel with the guidebook or provide similar information to ARFF personnel via a communication link. However, two airport operators expressed concern about requiring a specific document in part 139 that could become outdated and hamper existing hazardous materials emergency communication procedures already in place. Instead, these commenters preferred to focus such efforts on training.

In light of information and data provided by ATA and airport operators, the FAA proposes to change existing paragraph (j)(2)(x) ((proposed paragraph (i)(2)(x)), to revise the term “aircraft cargo hazards” to read “hazardous materials/dangerous goods incidents.” Similarly, new paragraph (j) would be added to this section prescribing a general requirement to equip aircraft rescue and firefighting vehicles with guidance for responding to hazardous materials/dangerous goods incident.

The FAA is a proponent of the North American Emergency Response Guidebook and proposes to require its use. This guidebook was developed jointly by the governments of Canada, Mexico, and the United States for use by fire fighters, police and other emergency services personnel who may be the first to arrive at the scene of a transportation incident involving hazardous materials or dangerous goods. The guidebook should be used by first responders to quickly identify the specific or generic hazards of the material(s) involved in the incident, and to protect themselves and the general public during the initial response phase of the incident. Other guidance material also may be needed.

While new paragraph (j) specifies the use of the North American Emergency Response Guidebook, it also would allow airport operators the flexibility to use other guidance material and to make such information available via direct communications links to ARFF personnel at the site of the incident (e.g., cellular telephone, radio, and other communication links).

New paragraph (i)(4) would impose requirements for emergency medical care training similar to existing requirements. The term “emergency medical care” would be amended to read “emergency medical services.” This change in terminology reflects current terminology used by the emergency response community. Further, it is proposed that emergency medical requirements be expanded to specify initial and recurrent training to eliminate any confusion over the frequency of such training.

Proposed paragraph (i)(5) would be a new requirement for the certificate holder to maintain records for two years from the date of any training given to meet the requirements of proposed § 139.319. Such records would, at a minimum, specify the type and date of training. To document compliance with this section, airport certificate holders already maintain these records and the FAA proposes to formalize this practice.

Similar to proposed § 139.317(l), new paragraph (m), titled “Implementation,” would specify a compliance date with airports that would be required for the first time to comply with the standards of this section (proposed Class II, III, and IV airports). The proposed compliance date allows these airports adequate time to acquire funding for, and purchase of, ARFF equipment and hire/train personnel. The FAA anticipates that approximately 110 airports (both certificated and non-certificated) would have to obtain additional equipment and personnel. Two years should be adequate time to secure Federal and local funds to purchase equipment and hire and train personnel. The FAA would consider a time extension for airports unable to comply within this 2-year timeframe.

Section 139.321 Aircraft Rescue and Firefighting: Exemptions

Existing § 139.321, Handling and storing of hazardous substances and materials, would be redesignated as § 139.323. Proposed § 139.321 is new and would establish procedures for certain airport certificate holders to request an exemption from the ARFF requirements of proposed §§ 139.317 and 139.319. This section would also detail what the FAA would consider in deciding to grant an exemption from the ARFF requirements. As proposed, the FAA could exercise its statutory authority to exempt certain airport certificate holders from the prescribed ARFF requirements. Through this statutory exemption, the FAA would maintain the necessary oversight of ARFF while ensuring that the ARFF requirements are appropriate for the airport size and type of air carrier operations.

Proposed paragraph (a) would establish that the certificate holder of an airport that meets the qualifications for an exemption, as specified in proposed § 139.111, may petition the Associate Administrator for Airports (as delegated by the Administrator) for an exemption to the ARFF requirements of proposed §§ 139.317 and 139.319. Specifically, the airport certificate holder would have to demonstrate that the ARFF requirement it is seeking exemption from would be unreasonably costly, burdensome, or impractical.

Proposed (b) would set forth procedures a certificate holder must take to request an exemption, including the information that must be included in the petition, i.e., the nature and extent of relief sought, and any alternative means of compliance.

Proposed paragraph (c) would establish criteria the FAA would use to grant exemptions on a case-by-case basis. As noted in the discussion of alternatives, any exemption would not relieve an airport certificate holder from its obligation to provide some level of ARFF coverage. All certificated airports would be required to provide ARFF coverage.

Proposed § 139.321(c) requires the certificate holder to submit a petition requesting relief from the requirements of §§ 139.317 and 139.319 that shows an equivalent level of safety would be provided during air carrier operations in response to aircraft emergencies. This would include provisions made by the certificate holder for prearranged firefighting and medical response, equipment and fire extinguishing agents to be used, and training of firefighting and medical responders. Also, this section specifies that the certificate holder will arrange for such emergency equipment and personnel to be on-airport 15 minutes before and 15 minutes after an air carrier aircraft takes off or lands. This should not be interpreted to mean that such pre-arranged ARFF services would necessarily be required to be stationed at the airport or wait on-airport during extended periods between flights.

Of approximately 570 civilian airports currently certificated under part 139, operators of approximately 500 of these airports would be eligible to petition for an exemption under this new section (as they have less than one quarter of one percent of the total number of annual passenger enplanements). The operators of the estimated 40 airports that could be newly certificated (proposed Class III airports), if this proposal is adopted, would be eligible to petition for an exemption from ARFF requirements as well. The FAA does not anticipate that all eligible certificate holders would apply for an exemption under this new section.

The FAA expects that most requests for an exemption would be made by airports that would have to provide more frequent ARFF services, such as some proposed Class I, as well as Class II and III airports. An analysis of existing ARFF services at these airports revealed that approximately 110 of these airports (approximately 50 Class I, 30 Class II, and 30 Class III airports) would require additional equipment or personnel to comply with proposed ARFF requirements (see discussion of ARFF costs in the Regulatory Evaluation section). To minimize disruptions at such airports, certificate holders at these facilities would have two years to comply with proposed changes to ARFF requirements. During this time, a certificate holder could choose to comply with these new requirements or request an exemption. Airport operators currently holding a “limited” certificate could request an exemption based on the currently approved ARFF response for their airport.

The FAA requests comments on this exemption process, including economic and operational data that would assist the FAA in evaluating the effectiveness of this process.

Section 139.323 Handling and Storing of Hazardous Substances and Materials

In this proposal, existing § 139.321, would be redesignated as proposed § 139.323. Existing § 139.321 requires certain airport operators to establish and implement procedures for the safe storage and handling of aviation fuel, lubricants, and oxygen, and when acting as a cargo agent, hazardous materials regulated under 49 CFR 171. This section also requires the certificate holder to conduct quarterly inspections of certain fueling agents. Generally, this proposal would not change these requirements.

Changes are proposed to existing paragraphs (b), (c), (h), and (i) of this section, as described below. All proposed airport classifications would be required to comply with the requirements of this revised section.

Airport operators that currently serve scheduled operations of large air carrier aircraft (proposed Class I airports) would continue to comply with existing § 139.321. Operators of airports holding an LAOC (proposed Class II and IV airports) would be required to update existing procedures for the storage and handling of hazardous materials required under existing § 139.213 to ensure their existing procedures meet the standards. Also, operators of proposed Class III airports would be required for the first time to develop and implement procedures for the storage and handling of hazardous materials. Depending on the local fire code, some operators of proposed Class III airports may have already developed such procedures and would need only to document such procedures in their ACM.

The majority of the ARAC Commuter Airport Certification Working Group recommended that airports serving small air carrier aircraft not be required to comply with this section. The working group expressed a need for such procedures, but noted most airport operators already have procedures that appear to be adequate for storing and handling hazardous materials at smaller facilities. Instead, the majority recommended that smaller facilities meet local fire codes pertaining to storage and handling of hazardous substances and materials, including aircraft fuel. The majority stated that this approach would adequately address preparedness and safety issues without being overly burdensome.

Representatives of the National Air Transportation Association (NATA) and ALPA disagreed with the majority position, and recommended that the FAA require airports serving small air carrier aircraft to comply with requirements of the existing section. ALPA raised concerns that local fire codes may not adequately address aircraft storage and refueling operations, and noted the working group's economic analysis found compliance with this section would not create an economic burden.

The FAA has determined that the requirements of this section are common safety measures and would not be unduly burdensome. Moreover, these standards were developed as a result of a cooperative effort between the FAA, airport operators, and FBO's, and have been successfully used for the past several years by airport operators and aircraft fuelers nationwide.

The FAA proposes to delete the term “grounded” from paragraph (b)(1). This paragraph would then correspond with the NFPA Standard 407, titled “Standard for Aircraft Fueling Servicing.” The NFPA standard recommends that only bonding should be used during aircraft fueling or refueler loading.

3

The FAA actively participates in development of NFPA codes and standards related to aviation fueling.

3

NFPA 407

—

Standard for Aircraft Fuel Servicing,

National Fire Protection Association, 1996 Edition.

The terms “grounding” and “bonding” describe methods to dissipate electrostatic charges created when aviation fuels pass through pumps, filters, and piping, and may consequently ignite fuel. Bonding is a procedure that provides a conductive path to equalize the potential electrostatic differential between fueling equipment and aircraft. Bonding is accomplished by connecting a cable between the fueling equipment and the aircraft. Alternatively, grounding attempts to reroute and dissipate potential charges into the ground by connecting the aircraft by a cable to a static wire, typically a rod in the ground.

The FAA concurs with NFPA 407 as testing has shown that most grounding provides little, if any, protection from electrostatic hazards. In addition to corrosion of rods in the ground, grounding points may have high electrical resistance. The static wire may not be sufficient to carry the potential current and, if the wire fuses, may actually constitute a source of ignition.

Since 1990, the FAA has encouraged the use of bonding in aircraft fueling, fuel delivery and hydrant servicing. The

FAA Office of Airport Safety and Standards has issued two informational notices, known as “CERTALERTS,” to alert FAA inspectors and airport operators to changes in grounding and bonding. “CERTALERTS” are advisory in nature and are issued periodically to provide timely information to certificate holders on a broad range of safety and airport certification related subjects. Subsequent to the issuance of NFPA 407, the FAA issued CERTALERT #91-06 (September 18, 1991) and CERTALERT #90-08 (November 7, 1990) urging the use of bonding only, and suggesting design requirements for the procedure. The FAA proposes to use this rulemaking action to codify this recommended practice.

In addition, paragraph (b)(6) would be modified to delete an implementation date that has already passed. In its place, a new requirement is proposed that would require operators of proposed Class III airports to complete specified training within one year.

Existing paragraph (e) would be modified to include requirements for annual recurrency training for fueling agent supervisors and employees. This is in response to requests by airport operators for clarification on frequency training. This requirement would be similar to recurrency training requirements proposed for other airport personnel (see discussion of § 139.319, Aircraft rescue and firefighting: Operational requirements) and training currently used by fueling agents. Most fueling agents work directly for, or indirectly represent, large fuel or aircraft service companies that have established safety programs that require periodic recurrency training.

Proposed changes to existing § 139.321(h) would clarify the certificate holder's responsibility for fuel storage areas owned or operated by tenant air carriers. Paragraph (h) currently exempts the certificate holder from overseeing part 121 or 135 air carrier fueling operations to ensure compliance with requirements of § 139.321. However, there are no equivalent requirements under parts 121 and 135 directing air carriers to inspect and maintain their fuel storage areas, as is required of airport operators under part 139. Sections 121.135 and 135.23 only address refueling aircraft and fuel quality.

On November 25, 1990, a fire erupted at a fuel storage and dispensing facility about 1.8 miles from the main terminal of Stapleton International Airport in Denver, Colorado. The fire was extensive, burning for 49 hours, and required a total of 634 firefighters, 47 fire units, and 4 contract personnel. More than 56 million gallons of water and 28,000 gallons of foam concentrate were expended to extinguish the fire. No injuries or fatalities occurred as a result of the fire.

4

4

Aviation Accident Report—Fuel Farm Fire at Stapleton International Airport, Denver, Colorado, November 25, 1990:

NTSB AAR-91/07, National Transportation Safety Board, October 1, 1991.

The NTSB investigation concluded that the probable cause of this accident was damaged pumping equipment resulting in leakage and ignition of fuel. The NTSB also concluded that a similar incident could be avoided if airport certificate holders were responsible for inspecting all fuel storage areas on the airport, including air carrier facilities.

The FAA concurs with this recommendation and proposes to delete existing paragraph (h) to avoid any possible confusion over who is responsible for maintaining and inspection fuel storage areas used by part 121 and 135 air carriers. Subsequently, existing paragraph (i) would become new paragraph (h). As proposed, new paragraph (h) would specify that the requirements of § 139.321 are applicable to air carrier fuel storage areas located on the airport. Existing paragraph (c) also would be amended to remove references to existing paragraph (h).

In addition, existing paragraph (i) (new paragraph (h)) would be revised to delete references to the specific series number within the AC system. Instead, this revised paragraph would make a general reference to the AC system.

Section 139.325 Traffic and Wind Direction Indicators

Under this proposal, the requirements of existing § 139.323 would be moved to proposed § 139.325. Existing § 139.323 prescribes conditions that require certificate holders to provide a wind cone and a traffic pattern indicator, and the standards for these devices. All proposed airport classifications would be required to comply with this proposed section.

Changes are proposed to clarify that airport operators must comply with the requirements of this section in a manner satisfactory to the FAA, and that the available AC's contain some methods of compliance that are acceptable to the Administrator. In addition, this proposal would revise standards for segmented circles and supplemental wind cones.

Existing § 139.323 requires airport certificate holders serving scheduled operations of large air carrier aircraft (proposed Class I airports) to provide traffic and wind indicators (such as windsocks) at specific locations on the airport. In addition, certain night and uncontrolled traffic operations require traffic and wind indicators. This requirement would not change under this proposal. Airport certificate holders having a LAOC (proposed Class II and IV airports) and operators of proposed Class III airports would need to comply with standards of this revised section.

Further, all certificate holders would be required to install supplemental wind cones adjacent to runway ends where the primary wind cone is not visible to a pilot on final approach or during takeoff. The existing standard only requires the use of supplemental wind cones if the airport is located in Class B airspace. Installation of supplemental wind cones would ensure current wind direction information is available to all pilots rather than just those using longer runways of airports typical of Class B airspace. Longer runway distances may limit a pilot's ability to see a mid-field wind cone during takeoff or landing. Linking the current standard to Class B airspace has unintentionally excluded those smaller airports with longer runways, particularly those military bases that have recently converted to civilian use.

Existing paragraph (b) also would be revised to update the standard for traffic indicators at airports without a control tower. Language proposed corresponds more closely to existing FAA guidance provided to pilots on visual indicators at airports without control towers. Specifically, the requirement for a segmented circle would be deleted and a new standard would be added for the location of landing strip and traffic pattern indicators.

While many operators of airports serving scheduled operations of small air carrier aircraft already provide traffic and wind indicators, the FAA believes that requiring all certificated airports to comply with this section would ensure standardization.. This position was supported by the ARAC Commuter Airport Certification Working Group report.

Section 139.327 Airport Emergency Plan

Existing § 139.325 requires certain certificate holders to develop and implement an emergency plan and to conduct tests of this plan. The section also specifies what the emergency plan must contain. In this proposal, existing § 139.325 would be moved to proposed § 139.327 and revised to address all proposed airport classifications. Changes also would be made to emergency response requirements for

incidents involving fuel fires and hazardous materials.

Airport certificate holders that currently serve scheduled operations of large air carrier aircraft (proposed Class I airports) must comply with existing requirements of § 139.325 to develop, implement, and test an emergency plan. These requirements would be extended to airport certificate holders currently holding a LAOC (proposed Class II and IV airports) and proposed Class III airport operators.

Airport certificate holders currently required to have an airport emergency plan must periodically test their plan. Specifically, these airport operators are required to conduct a disaster drill (know as a full-scale airport emergency plan exercise) every three years to test the validity of their emergency plan. A full-scale airport emergency plan exercise is a mock airport disaster staged to test and practice airport emergency procedures. In such exercises, the airport operator typically involves all mutual aid participants (local hospitals, police, fire departments, etc.), emergency vehicles and other equipment, and airport personnel and tenants, as specified in the airport emergency plan. The exercise usually is an all day event culminating several months of preparation, and is conducted using airport resources and support from the local community.

In the years in between the full-scale exercise, airport certificate holders are required to review their emergency plans to ensure procedures are still current and all parties involved know their responsibilities. The testing requirements for airports serving scheduled operations of large air carrier aircraft (proposed Class I airports) would not change as a result of this proposal.

Operators of proposed Class II, III, and IV airports would be required to annually review their emergency plan to ensure procedures are current and all parties involved know their responsibilities. These operators would not be required to conduct full-scale emergency exercises. Many of the communities that own and operate such facilities are small and have very limited resources. However, the FAA encourages these airports to work with their communities to develop feasible disaster drills.

The annual review, often referred to as a “table-top” exercise, would involve the airport meeting with responsible parties around a map of the airport to discuss possible emergency scenarios. The review is a reasonable requirement for airports serving small air carrier scheduled operations, and will ensure emergency procedures remain current without being unduly burdensome.

The ARAC Commuter Airport Certification Working Group recommends this approach to emergency preparedness in its report. The report states the cost of a full scale airport emergency plan exercise could be overly burdensome for airports serving small air carrier aircraft, and supported the use of table top exercises only. The report also recommended that such tabletop exercises include a field tour, identification of emergency staging areas, and perimeter security requirements to control access to and from disaster areas.

Other requirements throughout this section also would be modified. Existing paragraph (a) would be revised to clarify that the airport emergency plan provide for response to an emergency involving the largest air carrier aircraft serving the airport. While this requirement is currently found in existing paragraphs that address medical services and water rescue (paragraphs (c) and (f)), it has always applied to the entire section. To ensure that all applicable response measures accommodate the largest air carrier aircraft serving an airport, the FAA proposes moving this requirement to paragraph (a).

In response to an NTSB recommendation, the FAA proposes that existing paragraph (b) be modified to require certificate holders to include in the airport emergency plan instructions for response to fires at fuel farms or fuel storage areas.

In its investigation of the Denver fuel farm fire (see discussion of proposed § 139.323, Handling and storing of hazardous substances and materials), the NTSB found that while airport firefighters and the Denver Fire Department promptly responded to the fire, they were unable to maintain a continuous flow of foam onto the fire, and the fire reignited and quickly intensified. The NTSB concluded that the airport and local firefighters did not have, nor could they have been expected to have, a sufficient supply of foam concentrate to fight a fuel fire of this magnitude. However, the City of Denver and its fire department had not developed a contingency plan for a fire of this type, and eventually a private contractor that specialized in large-scale fuel fires was brought in to extinguish the fire. Arrangements for this private contractor were made only after a tenant air carrier became concerned that its tanks, neighboring those burning, would be damaged.

5

5

Ibid, pg. 53.

The NTSB determined this lack of procedures for responding to a fuel storage fire of this magnitude prolonged the duration of the emergency. The NTSB recommended that the FAA require part 139 certificate holders to have contingency plans for fighting very large fires such as fuel storage area fires. The FAA concurs with this recommendation and proposes to modify existing paragraph (b) to require certificate holders to include in the airport emergency plan instructions for response to fires at fuel farms or fuel storage areas.

Existing paragraph (b)(5), proposed paragraph (b)(6), would also be amended to reflect more current terminology. The term “radiological” would be replaced with the term “hazardous materials/dangerous goods.” This term would better reflect the type of incidents airports need to be prepared for, including incidents involving corrosive, biological, explosive, radioactive, or toxic air cargo or ground freight. This change also addresses the ATA petition for rulemaking regarding hazardous materials/dangerous goods incident guidance (see the discussion under proposed § 139.319).

Additionally, existing paragraph (d)(3) would be modified to include the new term “notification.” The revised section would allow airport operators to use either an alarm system or a notification system to announce an emergency. The ARAC Commuter Working Group report noted that smaller airports required to have an emergency plan may not have the resources to implement a sophisticated, automated alarm system used by many larger facilities. Instead, these smaller airports may use a notification system that is as simple as a series of telephone calls to summon emergency response. The requirement would ensure that an adequate system is in place, and periodically tested. Each airport would determine the type of system that best meets its needs.

Existing paragraph (g)(5) would be moved to new paragraph (h) and existing paragraph (h), prescribing acceptable methods and procedures, would become new paragraph (i). New paragraph (h) would prescribe the requirement for, and the frequency of, full-scale airport emergency plan exercises, as described earlier.

Requirements in paragraphs (d) and (f) that relate to water rescue situations and coordination with control towers would be clarified to apply only to those airports with water on or adjacent to the airport, or with a control tower.

New paragraph (j) would allow certificate holders of proposed Class II,

III, and IV airports one year from the effective date of the rule to submit their emergency plans to the FAA for approval. Even though the FAA provides guidance materials to aid in the development of an airport emergency plan, the process will require coordination and cooperation with the surrounding communities and may be a time consuming process.

Section 139.329 Self-Inspection Program

Existing § 139.327 requires certificate holders to conduct daily inspections of the movement area to ensure the airport remains in compliance with part 139. This section specifies additional conditions that require inspections. Also, the certificate holder is required to have a system to notify air carriers of field conditions and a recordkeeping system to document inspections.

In this proposal, existing § 139.327 would be redesignated as proposed § 139.329 and revised to address training requirements for individuals conducting airport inspections. Language also would be added to permit airport inspections to be conducted by individuals other than employees of the airport operator. All proposed airport classes would be required to comply with this revised section.

The proposed changes to existing § 139.327 will assist existing and new airport certificate holders in understanding their responsibilities to inspect their facilities. As a consequence, airport operators already required to have a self-inspection program under existing § 139.205 would need to modify their inspection program.

Operators of airports that currently serve scheduled operations of large air carrier aircraft (proposed Class I airports) must continue to comply with the requirements of this section, and would be required to modify their inspection program. Airport certificate holders holding an existing LAOC (proposed Class II and IV airports) would be required to update existing self-inspection programs. In addition, operators of proposed Class III airports would be required to develop and implement an self-inspection program.

Existing paragraph (a) would be amended to allow airport operators to designate individuals of their choice to conduct inspections as long as the individuals meet the requirements of this section. For example, the proposed change would allow the airport operator to designate an individual other than airport personnel, such as air carrier station personnel or an employee of an FBO, to conduct required inspections when airport personnel are not present during hours of scheduled operations. A similar proposal was recommended by the ARAC Commuter Airport Certification Working Group to permit airports serving scheduled operations of small air carrier aircraft to designate inspection responsibilities.

This proposal could reduce labor costs associated with personnel working overtime or the need to hire additional employees to cover early morning or late evening operations, particularly when tenant employees will be present during these hours of operation. However, the certificate holder would be responsible for ensuring that inspections are done correctly, and that individuals conducting inspections are qualified to perform the duties associated with the inspection.

Personnel requirements of existing paragraph (b) would be enhanced to require that personnel meet the requirements of proposed § 139.303, Personnel, and to be trained in specific topics, including airport familiarization and discrepancy reporting procedures. This change is necessary to ensure that certificate holders are using qualified individuals to conduct airport inspections, particularly in light of the proposal to use designees to perform this function.

Section 139.331 Ground Vehicles

Under this proposal, the requirements of existing § 139.329 would not be changed but the section would be redesignated as proposed § 139.331. Existing § 139.329 requires the certificate holder to limit access to movement areas to those ground vehicles necessary for airport operations. This section also requires the certificate holder to ensure that employees, tenants, or contractors who operate ground vehicles in the movement area are familiar with established ground vehicle operating procedures. Currently, operators of airports certificated to serve scheduled operations of large air carrier operations must comply with existing § 139.329.

Minor modifications are proposed to clarify that the requirements of this section are implemented in a manner satisfactory to the FAA. All certificated airports serving scheduled air carrier operations (proposed Class I, II, and III airports) would be required to comply with this revised section.

Except for representatives of the National Air Transportation Association (NATA) and ALPA, the ARAC Commuter Airport Certification Working Group report recommended that operators of airports serving scheduled operations of small air carrier aircraft be required to comply only with training and reporting measures of paragraphs (e) and (f) of this section. The working group noted the importance of familiarization with proper vehicle safety procedures; however, the majority of the group was concerned that other requirements of this section would be operationally or economically excessive for the limited number of scheduled air carrier operations at these airports.

The working group also noted that many of these airports do not have towers, and therefore do not warrant extensive ground vehicle requirements contained in this section. The FAA disagrees with this position. While existing § 139.329(c) requires the use of two-way radios, escort vehicles, and specialized procedures when radios are inoperative, these measures are only applicable at airports where an air traffic control tower is operational. Further, operators of airports with FAA control towers enter into a letter of agreement with FAA Air Traffic Control that requires ground vehicle procedures in movement areas. Operators of most affected airports already work with their tenants to implement such procedures.

Also, standards have been developed for the consistent application of this section as a result of a cooperative effort between the FAA, airport operators, and FBO's. These standards have been successfully used for the past several years, and should continue in a manner that is already well understood and, in most cases, used by airport operators and their tenants nationwide.

Section 139.333 Obstructions and Section 139.335 Protection of Navaids

In this proposal, the requirements of existing §§ 139.331 and 139.333 would remain substantially unchanged but would be redesignated as proposed §§ 139.333 and 139.335, respectively. These sections specify standards for obstructions, and the protection of navigational aids.

Clarifications are proposed that state that the requirements of this section must be implemented in a manner satisfactory to the FAA, and that the AC's contain some methods of compliance that are acceptable to the Administrator. All certificated airports serving scheduled air carrier operations (proposed Class I, II, and III airports) would be required to comply with these revised sections.

Existing § 139.331 (proposed § 139. 333) requires certificate holders to ensure that each object within its area of authority that penetrates imaginary surfaces, as provided in part 77, Objects Affecting Navigable Airspace, is

removed, marked, or lighted. Existing § 139.333 (proposed § 139.335) requires the certificate holder to protect against the derogation of electronic or visual navigational equipment (navaids) and air traffic control facilities located on the airport. This includes protection against vandalism, theft and construction that may cause interference.

Both the FAA and the ARAC Working Group agree that airports serving scheduled operations of small air carrier aircraft should meet these requirements. Many of these airports already provide for the removal or marking of obstacles, and have procedures in place to protect navaids. This minimizes disruption of aircraft operations and limits liability.

Section 139.337 Public Protection

Under this proposal, the requirements of existing § 139.335, would not be changed but the section would be moved to proposed § 139.337. Existing § 139.335 requires certificate holders to prevent the inadvertent entry of persons or vehicles to the movement area, and to provide reasonable protection of persons and property for aircraft blast. All certificated airports serving

scheduled

air carrier operations would be required to comply with this section. This would include proposed Class I, II, and III airports.

This section would continue to require the airport certificate holders to provide safeguards to prevent inadvertent entry to movement areas b

This text is long and has been trimmed here. Open the source document for the complete record.