# 8 CCR 1302-14: NON-RESIDENTIAL AND RESIDENTIAL FACTORY-BUILT STRUCTURES AND TINY HOMES; SELLERS OF MANUFACTURED HOMES AND TINY HOMES; MANUFACTURED HOME, TINY HOME, AND MULTI-FAMILY STRUCTURE INSTALLATIONS > Colorado · Regulations · In force URL: https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_14 ## Section - **Citation:** 8 CCR 1302-14 - **Heading:** NON-RESIDENTIAL AND RESIDENTIAL FACTORY-BUILT STRUCTURES AND TINY HOMES; SELLERS OF MANUFACTURED HOMES AND TINY HOMES; MANUFACTURED HOME, TINY HOME, AND MULTI-FAMILY STRUCTURE INSTALLATIONS - **Jurisdiction:** Colorado - **Kind:** Regulations - **Status:** In force - **Text as of:** August 14, 2026 - **Source:** Compiled text - **Location:** Code of Colorado Regulations / 1300 Department of Local Affairs / 1302 Division of Housing / 8 CCR 1302-14 ## Text 1 DEPARTMENT OF LOCAL AFFAIRS Division of Housing NON-RESIDENTIAL AND RESIDENTIAL FACTORY-BUILT STRUCTURES AND TINY HOMES; SELLERS OF MANUFACTURED HOMES AND TINY HOMES; MANUFACTURED HOME, TINY HOME, AND MULTI-FAMILY STRUCTURE INSTALLATIONS; FOUNDATION SYSTEMS FOR MANUFACTURED HOMES, TINY HOMES, AND FACTORY-BUILT STRUCTURES WHERE NO STANDARDS EXIST; AND HOTELS, MOTELS, AND MULTI-FAMILY STRUCTURES IN THOSE AREAS OF THE STATE WHERE NO STANDARDS EXIST 8 CCR 1302-14 [Editor’s Notes follow the text of the rules at the end of this CCR Document.] Rule 1. Definitions. In addition to the definitions provided in section 24-32-3302, C.R.S., the following definitions apply to these rules: 1.1 “Authorized quality assurance representative” as defined in section 24-32- 3302(1), C.R.S., means a “third party agency” (defined in Rule 1.35 below) approved by the Division of Housing. 1.2 “Alternative Construction” or “AC” has been replaced with “On-site Construction (OC)” in Rule 1.21. This definition has been left in since there are number of forms and documents circulating with this legacy term. 1.3 “Authority Having Jurisdiction” or “AHJ” means the local government’s building department with oversight over where the structure is to be located. 1.4 “Built-for-Purpose Trailer” means a vehicle trailer that is built to serve as a construction platform for a tiny home and has: a Vehicle Identification Number (VIN), a Gross Vehicle Weight Rating (GVWR), and is capable of sustaining and moving a tiny home. 1.5 “Certificate of Occupancy” means a certificate issued by the Division of Housing stating at the time of issuance the structure was built in compliance with all applicable codes and construction standards adopted by the State Housing Board. It only applies to motels, hotels, and multi-family structures in those areas of the state where no such standards exist. Code of Colorado Regulations Secretary of State State of Colorado CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing the time of issuance the structure was built in compliance with all applicable codes and construction standards adopted by the State Housing Board. It only applies to motels, hotels, and multi-family structures in those areas of the state where no such standards exist. Code of Colorado Regulations Secretary of State State of Colorado CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 2 1.6 “Certified” is the status given by the Division of Housing to an installer, independent contractor, manufacturer, or Third Party Agency after submission of an application and required documentation set in rule, has shown compliance with the minimum performance standards for quality control of their respective registration requirements and approved by the Division. A business entity may become certified only when all registered installers within that entity have been certified. A certified individual installer registered under the business entity is authorized to only certify an installation that they supervised completion of in compliance with Rule 1.10. 1.7 “Certified Inspector” means one of the following individuals authorized by the Division of Housing: 1.7.1 An “independent contractor” as defined pursuant to section 24-32- 3302(15), C.R.S., that is authorized by the Division of Housing to perform or enforce installation inspections, 1.7.2 An employee of a “state” or “firm” as used in the definition of a “quality assurance representative” pursuant to section 24-32-3302(30), C.R.S., and further defined in Rule 1.35.2 of these rules, or 1.7.3 A Colorado licensed engineer that is authorized by the Division of Housing to perform an On-site Construction inspection and oversight manufacturer inspection. 1.8 “Closed Panel System” means a building component or assembly built off-site that may include electrical, plumbing, mechanical, or insulation with finishes applied to both sides and then transported to be erected on-site to complete a residential or nonresidential building authorized by the Division of Housing to perform an On-site Construction inspection and oversight manufacturer inspection. 1.8 “Closed Panel System” means a building component or assembly built off-site that may include electrical, plumbing, mechanical, or insulation with finishes applied to both sides and then transported to be erected on-site to complete a residential or nonresidential building. 1.9 “Conflict of Interest” means when there is personal or private interest(s) sufficient to influence or appear to influence the proper exercise of duties or responsibilities. 1.10 “Direct On-site Supervision” as used in section 24-32-3315(1)(b)(I), C.R.S., means the registered or certified installer must be present at the installation “site” as defined by section 24-32-3302(33), C.R.S., and readily available to properly supervise installation work as defined by section 24-32-3302(16), C.R.S., that is performed by an employee not registered or certified as an installer. 1.11 “Down payment(s)” as used in section 24-32-3325(2)(b), C.R.S, and Rules 5.3, 5.4, 5.10, and 5.11, means all money given by a purchaser to a seller for the purchase of a manufactured home or tiny home before the manufactured home or tiny home is delivered. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 3 1.12 “Factory-built” means the construction of nonresidential structures or residential structures (modular homes, tiny homes, or multi-family structures) that occurs at an offsite location (e.g. manufacturing plant, small business space or school workshop, or private barn), separate from the site where the structure is to be installed. 1.13 “Firm” as used in the definition of an “independent contractor” pursuant to section 24-32-3302(15), C.R.S., and in the definition of a “quality assurance representative” pursuant to section 24-32-3302(30), C.R.S., means a “third party agency” (defined in Rule 1.35 below) , small business space or school workshop, or private barn), separate from the site where the structure is to be installed. 1.13 “Firm” as used in the definition of an “independent contractor” pursuant to section 24-32-3302(15), C.R.S., and in the definition of a “quality assurance representative” pursuant to section 24-32-3302(30), C.R.S., means a “third party agency” (defined in Rule 1.35 below). 1.14 “HUD-code Home” means a manufactured home constructed in compliance with the “National Manufactured Housing Construction and Safety Standards Act of 1974”, 42 U.S.C. sec. 5401 et seq., and any standard promulgated by the Secretary of the U.S. Department of Housing and Urban Development (HUD) pursuant to that federal act. 1.15 “Individual” as used in the definition of an “independent contractor” pursuant to section 24-32-3302(15), C.R.S., means a Colorado licensed professional engineer (PE) or architect authorized by the Division of Housing to perform or enforce installation inspections. 1.16 “Insignia” means a seal, label, or tag issued by the Division of Housing that when permanently affixed to a structure confirms compliance as one of the following: 1.16.1 An “insignia of approval” pursuant to sections 24-32-3303(1)(c), 24-32- 3310, 24-32-3311(a), 24-32-3311(1)(a.5), 24-32-3311(1)(b), 24-32- 3311(4), 24-32-3311(5), C.R.S., issued by the Division of Housing or an “authorized quality assurance representative” pursuant to sections 24-32- 3302(1), 24-32-3303(1)(c), 24-32-3304(1)(e), 24-32-3311(1)(a), 24-32- 3311(1)(b), 24-32-3311(4), and 24-32-3311(5), C.R.S., verifies that a factory built structure is deemed to be designed and constructed in compliance with the requirements of all codes and standards enacted or adopted by the state and accounts for any local government installation requirements ntative” pursuant to sections 24-32- 3302(1), 24-32-3303(1)(c), 24-32-3304(1)(e), 24-32-3311(1)(a), 24-32- 3311(1)(b), 24-32-3311(4), and 24-32-3311(5), C.R.S., verifies that a factory built structure is deemed to be designed and constructed in compliance with the requirements of all codes and standards enacted or adopted by the state and accounts for any local government installation requirements. 1.16.2 A “certificate of installation” as defined pursuant to section 24-32-3302(3), C.R.S., and issued by the Division of Housing or a party authorized by the Division of Housing, verifies compliance with the installation standards established by the State Housing Board in Rule 2.12 through 2.14 of these rules. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 4 1.17 “Installation Authorization” pursuant to sections 24-32-3317(1), 24-32-3317(2), and 24-32-3317(4), C.R.S., means a Division of Housing approved form posted on the site of an installation, located beyond the authority of a “participating jurisdiction” as defined in Rule 1.23, verifying that the home owner or registered installer has made application with the Division of Housing to install a manufactured home or a tiny home and has received authorization to install it, or that the home will be installed by a certified installer who has automatic authorization to do so under their certified status. 1.18 “Multi-family structure(s)” means a commercial use structure containing at least three independent dwelling units within an International Building Code (IBC) Group R-2, R-3, or R-4 building; or a residential use structure built to the International Residential Code (IRC) Townhouse building provisions. Such commercial uses are limited to apartments, condominiums, live work units, vacation time shares, and other similar uses with independent dwelling units where the building is used, intended, or designed to be built, used, rented, leased, let, or hired out to be occupied or that are occupied for living purposes ture built to the International Residential Code (IRC) Townhouse building provisions. Such commercial uses are limited to apartments, condominiums, live work units, vacation time shares, and other similar uses with independent dwelling units where the building is used, intended, or designed to be built, used, rented, leased, let, or hired out to be occupied or that are occupied for living purposes. 1.19 “No cover” means no materials, appliances, or equipment should be concealing any component specifically requested to be exposed for inspection by the Division or its approved Third Party Agency or required for rough inspection per the adopted codes in these Administrative Rules. 1.20 “Occupancy” or “Occupied” means a factory-built structure, manufactured home, or tiny home designed, built, modified, or used with the intent for individuals to enter. 1.21 “On-site Construction” or “OC” means on-site construction or modification of the factory-built structure that directly relates to the durability, quality, and safety; that is completed at the installation “site” as defined by section 24-32-3302(33), C.R.S.; using components not installed at the manufacturer’s location; and to complete the compliance of that structure as reflected in the Division of Housing approved plans. These items do not include the component(s) required for setting and securing the structure for its installation. 1.22 “Open Construction” means any building component, assembly, or system manufactured in such a manner that all concealed parts or processes of manufacture can be readily inspected at the building site without disassembly, damage, or destruction, i.e., panelized construction assembled on site, or units that arrive onsite for a no cover inspection by local jurisdiction. Note: Assembled rooms or spaces, panels with finishes applied to both sides and electrical wiring in conduit are not open construction, but rather a “closed panel system” as defined pursuant to Rule 1.8. ected at the building site without disassembly, damage, or destruction, i.e., panelized construction assembled on site, or units that arrive onsite for a no cover inspection by local jurisdiction. Note: Assembled rooms or spaces, panels with finishes applied to both sides and electrical wiring in conduit are not open construction, but rather a “closed panel system” as defined pursuant to Rule 1.8. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 5 1.23 “Participating Jurisdiction” means a “local government” as defined pursuant to section 24-32-3302(18), C.R.S., which has agreed to administer and inspect manufactured housing installations within the legal boundaries of the jurisdiction and in compliance with the manufactured home, multi-family, and tiny home installation standards established by the State Housing Board in rules 2.12 through 2.14 of these rules. 1.24 “Permanent Foundation” as defined in section 24-32-3302(26.5) C.R.S, is further defined to account for point loads of the structure to the ground, prevent lateral movement and overturning of the structure, and provide frost protection. Local government building departments are responsible for design review and approval of permanent foundations. For areas of the state without a local government building department, the Division of Housing will review and approve permanent foundations designed by a Colorado licensed design professional. 1.25 “Plan” means a specific design for the construction of a structure submitted by the manufacturer to the Division of Housing for review and approval that typically includes a floor plan, elevation drawings, structural pages, electrical circuit layouts, recommended foundation drawings, mechanical drawings, plumbing isometrics, cross section drawings, an energy code compliance report, heat load calculations, and the engineering calculations nstruction of a structure submitted by the manufacturer to the Division of Housing for review and approval that typically includes a floor plan, elevation drawings, structural pages, electrical circuit layouts, recommended foundation drawings, mechanical drawings, plumbing isometrics, cross section drawings, an energy code compliance report, heat load calculations, and the engineering calculations. 1.26 “Quality Control Procedures” means procedures prepared by a manufacturer for each of its manufacturing facilities and approved by the Division of Housing or “third party agency” (defined in Rule 1.35. below) describing the method that the manufacturer uses to assure structures produced by that manufacturer are in conformance with the applicable standards, codes, and approved plans. 1.27 “Red Tag Notice” means a physical identification posted visibly on a particular structure indicating that it is in violation of applicable state statutes, federal law, or these rules. A structure posted with this notice cannot be sold, offered for sale, nor have occupancy in Colorado. 1.28 “Registered” is the status that is given by the Division of Housing that signifies that an installer, independent contractor, seller, or manufacturer has met the minimum requirements for registration, and approved by the Division, through submission of an application and required documents set in rule. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing have occupancy in Colorado. 1.28 “Registered” is the status that is given by the Division of Housing that signifies that an installer, independent contractor, seller, or manufacturer has met the minimum requirements for registration, and approved by the Division, through submission of an application and required documents set in rule. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 6 1.29 “Remote Inspection” means a production inspection performed where the inspector is in a location other than the location where the structure is being manufactured using a computer having an internet or cellular connection to communicate with a manufacturer’s representative responsible for quality control. The manufacturer’s representative responsible for quality control shall utilize a smart device (cell phone, tablet, etc.). The inspection must be performed in “real time” with continuous live stream video from the manufacturing location, and two- way audio. Each inspection must be securely stored on the internet and retrievable by VIN, serial number, insignia number or other approved identifier. Remote inspections may only be conducted by an approved Third Party Agency”. 1.30 “State Administrative Agency” or “SAA” means the Building Codes & Standards Section of the Department of Local Affairs’ Division of Housing which has been approved or conditionally approved by the federal government to carry out its state plan for enforcement of its standards pursuant to Rule 2.8 of these rules. 1.31 “Temperature Sensitive Equipment” means equipment or instrumentation whose performance or lifespan can change due to changes in the ambient temperature surrounding that equipment or instrumentation. 1.32 “Temporary Foundation” As defined in section 24-32-3302(34) C.R.S., is further defined to clarify that local government building departments are responsible for design review and approval of temporary foundations sitive Equipment” means equipment or instrumentation whose performance or lifespan can change due to changes in the ambient temperature surrounding that equipment or instrumentation. 1.32 “Temporary Foundation” As defined in section 24-32-3302(34) C.R.S., is further defined to clarify that local government building departments are responsible for design review and approval of temporary foundations. For areas of the state without a local government building department, the Division of Housing will review and approve temporary foundation designed by a Colorado licensed design professional. 1.33 “Temporary Structure” means a structure that is intended to be installed at a location for no longer than 180 days. 1.34 “Temporary Use” means a structure that is only intended to be occupied for short periods of time. This use may be for temporary or permanent structures. 1.35 “Third Party Agency” means one of the following entities authorized by the Division of Housing: 1.35.1 “Firm” as used in the definition of an “independent contractor” pursuant to section 24-32-3302(15), C.R.S., to perform or enforce installation inspections, or 1.35.2 “State” or “firm” as used in the definition of a “quality assurance representative” pursuant to section 24-32-3302(30), C.R.S., to: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 7 (A) Inspect a manufacturer’s registered or certified facility by conducting a “production review” pursuant to section 24-32- 3302(28), C.R.S., in order to determine its ability to follow a building “plan” approved by the Division of Housing and the construction standards and codes adopted by the State Housing Board, evaluating a manufacturer’s “quality control procedures”, and performing design evaluations; (B) Inspect a factory-built structure or tiny home at seller lots or on site as part of an oversight inspection of a registered factory, random audit inspection of a certified factory, or an on-site construction (OC) inspection to ensure compliance with construction standards and codes ado e Housing Board, evaluating a manufacturer’s “quality control procedures”, and performing design evaluations; (B) Inspect a factory-built structure or tiny home at seller lots or on site as part of an oversight inspection of a registered factory, random audit inspection of a certified factory, or an on-site construction (OC) inspection to ensure compliance with construction standards and codes adopted by the State Housing Board; and (C) Certify a manufacturer’s factory-built structure or tiny home by affixing an insignia of approval issued by the Division of Housing deeming it to be designed and constructed in compliance with the requirements of all codes and standards enacted or adopted by the State and accounting for any local government installation requirements adopted in compliance with sections 24-32-3310 and 24-32-3318. 1.36 “Tiny House” is distinct from a “tiny home” as defined pursuant to section 24-32- 3302(35), C.R.S. in that a “tiny house” as defined in Appendix AQ of the 2021 International Residential Code shall be installed on a permanent foundation. 1.37 “Vehicle Chassis” means the base frame of a single-family dwelling, designed and constructed for long-term occupancy that supports the home’s construction and transportation, and includes axles, wheels, GVWR and a VIN. 1.38 “Wildfire Risk” means local building codes applied to meet the intent of the International Wildland-Urban Interface Code per Chapter 5 – Special Building Construction Regulations. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing designed and constructed for long-term occupancy that supports the home’s construction and transportation, and includes axles, wheels, GVWR and a VIN. 1.38 “Wildfire Risk” means local building codes applied to meet the intent of the International Wildland-Urban Interface Code per Chapter 5 – Special Building Construction Regulations. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 8 Rule 2. Codes and Standards Pursuant to sections 24-32-3303(1), 24-32-3304(1)(a) and (b), and section 24-32- 3305(2), C.R.S., the State Housing Board hereby adopts and incorporates by reference the following nationally recognized codes, standards, guidelines, procedures, or rules in their entirety, except for the revisions, additions, deletions, or exceptions/exemptions specified below. The incorporated codes, standards, guidelines, procedures, or rules do not include later revisions. They are readily available for public inspection in written format during the regular business hours at the Division of Housing, Building Codes and Standards Section, 1313 Sherman Street, Suite 320, Denver, CO 80203. Paper copies are available for a reasonable fee paid to the Division of Housing. Electronic copies are available from the agencies originally issuing them as noted below. In the case of a conflict between an adopted code, standard, procedure, or rules, the program will review and provide written guidance. Building Codes for Factory-Built Residential Structures and Tiny Homes; Factory- Built Nonresidential Structures; and Site-Built Hotels, Motels, and Multi-Family Structures in those areas of the State where no Standards Exist Manufacturers are permitted to use the construction codes in effect prior to the adoption of any new code for a maximum of 180 days after the amendment in rule takes effect . Building Codes for Factory-Built Residential Structures and Tiny Homes; Factory- Built Nonresidential Structures; and Site-Built Hotels, Motels, and Multi-Family Structures in those areas of the State where no Standards Exist Manufacturers are permitted to use the construction codes in effect prior to the adoption of any new code for a maximum of 180 days after the amendment in rule takes effect. The Program Manager for the Building Codes & Standards Section, the Director of the Office of Regulatory Oversight, the Deputy Division Director, or the Division Director is authorized to grant, in writing, one extension, for a period not more than 180 days. 2.1 The International Building Code (IBC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org. 2.1.1 Section 105.2 Work exempt from permit Revise #1 within “Building” to: 2.1.1.1 Any structures that are one story in height and utilized for the storage of equipment or materials that: - Do not exceed 120 sq. ft. - Are not connected to a permanent utility (power, sewer, fuel-gas) - Are not classified as an electrical hazardous area per Article 500 of the NEC (is a nonhazardous area), and - Are not installed on a permanent foundation. 2.1.1.2 Listed Structures CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 9 A building that in its entirety operates as a listed product is automatically exempt as long as the manufacturer is able to demonstrate it is labeled as such. 2.1.1.3 Open Panel Construction: A building component, assembly, or system constructed in the factory as open construction (see definitions). The above exemptions from approval through the State factory-built program do not grant any exemption from local jurisdiction requirements or state electrical or plumbing requirements. The above exemptions do not grant authorization for any work to be done in a manner that is in violation of the provisions of the adopted codes stem constructed in the factory as open construction (see definitions). The above exemptions from approval through the State factory-built program do not grant any exemption from local jurisdiction requirements or state electrical or plumbing requirements. The above exemptions do not grant authorization for any work to be done in a manner that is in violation of the provisions of the adopted codes. 2.1.2 Section 901.2 Fire Protection systems Add the following new section: 2.1.2.1 Section 901.2.1 Certified inspector required An automatic fire sprinkler system shall be installed in buildings as required by the local jurisdiction where the structure will be set. Final tests required by this Section shall be approved by a certified inspector 2.1.3 Section 907.2.10.2 (1) Smoke Alarms – Location Revise “immediate vicinity” to read “within 15 feet”. 2.1.4 Section 907.2.10.6 Smoke Alarms – Power Source Add to the end of the paragraph the following: Smoke and/or carbon monoxide alarms shall not be installed on a circuit dedicated only for smoke and/or carbon monoxide alarms. 2.1.5 Section 915.2.1 Carbon monoxide alarms – Locations Revise “immediate vicinity” to read “within 15 feet”. 2.1.6 Section 915.4.1 Carbon monoxide alarms – Power Source Add to the end of the paragraph the following: Smoke and/or carbon monoxide alarms shall not be installed on a circuit dedicated only for smoke and/or carbon monoxide alarms. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing tion 915.2.1 Carbon monoxide alarms – Locations Revise “immediate vicinity” to read “within 15 feet”. 2.1.6 Section 915.4.1 Carbon monoxide alarms – Power Source Add to the end of the paragraph the following: Smoke and/or carbon monoxide alarms shall not be installed on a circuit dedicated only for smoke and/or carbon monoxide alarms. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 10 2.1.7 Section 1006.1 Numbers of Exit Access Doorways Add 1006.1 Single exit in certain multifamily residential structures – For multifamily residential structures that meet the requirements of Colorado Revised Statutes 30-28-213 or 31-15-604, a single exit may serve a building no more than five stories for Group R-2 Occupancy. 2.1.8 Chapter 13 Delete in its entirety. 2.1.9 Section 1507.1.1 Ice barriers Add the following sentence at the beginning: Due to a history of ice forming along the eaves in Colorado, an ice barrier is required. And add the following language at the end of the first sentence: ...or not fewer than two layers of underlayment cemented together and to the roof. 2.1.10 Section 1608.2 Ground snow loads Revise to read as follows: Roof Snow Load (Pf) shall be in accordance with the local jurisdiction requirements and shall not be less than a minimum roof snow load of 30 PSF. The allowable increase of snow duration shall not be used when the snow load is above 65 PSF. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing ed together and to the roof. 2.1.10 Section 1608.2 Ground snow loads Revise to read as follows: Roof Snow Load (Pf) shall be in accordance with the local jurisdiction requirements and shall not be less than a minimum roof snow load of 30 PSF. The allowable increase of snow duration shall not be used when the snow load is above 65 PSF. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 11 2.1.11 Section 1609.3.1 Wind speed conversion Add this new section with the following language: The 3 second gust basic wind speed shall be in accordance with the local jurisdiction requirements. For jurisdictions that have adopted a building code edition prior to the 2012, the basic wind speed of that jurisdiction shall be multiplied by 1.20 for Risk category I structures, 1.29 for Risk category II structures, and 1.38 for Risk category III and IV structures to obtain Vult. The design wind speed Vult shall not be less than the minimum basic wind speeds as follows (Risk category as determined by Table 1604.5): Risk category I structures – 105 MPH Risk category II structures – 115 MPH Risk category III and IV structures – 120 MPH The Exposure category shall be C, unless otherwise justified. 2.1.12 Section 2111.1 and 2111.14.1 Fireplaces Add this new section with the following language: Every new fireplace must comply with one of the following: 1. Listed and labeled fireplace and chimney systems composed of factory-made components, and assembled in the field in accordance with the manufacturer’s instructions and the conditions of the listing, and 2. Approved gas logs. 2.2 The International Residential Code (IRC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org. 2.2.1 Section 105.2 Work exempt from permit Revise #1 within “Building to: - Any structures that are one story in height and utilized for the storage of equipment or materials that: - Do not exceed 200 sq. ft., ernational Residential Code (IRC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org. 2.2.1 Section 105.2 Work exempt from permit Revise #1 within “Building to: - Any structures that are one story in height and utilized for the storage of equipment or materials that: - Do not exceed 200 sq. ft., CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 12 - Are not connected to a permanent utility (power, sewer, fuel-gas) - Are not classified as an electrical hazardous area per Article 500 of the NEC (is a nonhazardous area), and - Are not installed on a permanent foundation. Listed Structures A building that in its entirety operates as a listed product is automatically exempt as long as the manufacturer is able to demonstrate it is labeled as such. Open Panel Construction A building component, assembly, or system constructed in the factory as open construction (see definitions). The above exemptions from approval through the State factory-built program do not grant any exemption from local jurisdiction requirements or state electrical or plumbing requirements. The above exemptions do not grant authorization for any work to be done in a manner that is in violation of the provisions of the adopted codes. 2.2.2 Table R301.2 (1) - Revise as follows: Climatic or Geographic Design Criteria for IRC Dwellings (Risk Category II Structures) Division of Housing Minimum Roof Snow load(1) 30 psf, non-reducible Basic Wind Speed(1) 115 mph (Vult), Exposure C Wind Topographic Effects Per Local Seismic Design Category(1) Minimum B Weathering Severe Frost Line Depth(4) Per Local CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing se as follows: Climatic or Geographic Design Criteria for IRC Dwellings (Risk Category II Structures) Division of Housing Minimum Roof Snow load(1) 30 psf, non-reducible Basic Wind Speed(1) 115 mph (Vult), Exposure C Wind Topographic Effects Per Local Seismic Design Category(1) Minimum B Weathering Severe Frost Line Depth(4) Per Local CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 13 Climatic or Geographic Design Criteria for IRC Dwellings (Risk Category II Structures) Division of Housing Minimum Termite Damage Slight Winter Design Temperature(2) Per Local Ice Barrier Underlayment Requirement Yes Flood Hazards Per Local Air Freezing Index(3) Per Local Mean Annual Temperature(3) Per Local Wildfire Risk Per Local Radon Mitigation Per Local ADU Fire Separation Per Local (1)The roof snow load, wind design, and seismic zone shall be in accordance with the local jurisdiction requirements and shall not be less than the minimums stated. The allowable increase for snow duration shall not be used when the snow load is above 65 PSF. (2)See Appendix B and verify with local jurisdiction. (3)See the National Climatic Data Center data table “Air Freezing Index-USA Method (Base 32o Fahrenheit)” at www.ncdc.noaa.gov. (4) In areas of the state without a local jurisdiction, the Division of Housing will approve all temporary or permanent foundation systems as defined in Rule 2. 2.2.3 Table R301.5 – Live Loads Add footnote (j) to Decks, Porches, Exterior balconies, Fire escapes to read as follows: e National Climatic Data Center data table “Air Freezing Index-USA Method (Base 32o Fahrenheit)” at www.ncdc.noaa.gov. (4) In areas of the state without a local jurisdiction, the Division of Housing will approve all temporary or permanent foundation systems as defined in Rule 2. 2.2.3 Table R301.5 – Live Loads Add footnote (j) to Decks, Porches, Exterior balconies, Fire escapes to read as follows: (j)When the snow load is above 65 psf, the minimum uniformly distributed live loads for exterior balconies, decks and fire escapes shall be as required for roof snow loads. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 14 2.2.4 Table R302.1 (1) – Exterior Walls Delete footnote (b). 2.2.5 Table R302.1 (2) – Exterior Walls—Dwellings with Fire Sprinklers Delete footnote (c). 2.2.6 Section R308.4.6 Glazing adjacent to stairs and ramps Revise to include the following sentence as an exception: 1. Where the glazing is protected by a guard complying with Section R312 and the plane of the glass is more than 18 inches (457 mm) from the guard. 2.2.7 Section R308.4.7 Glazing adjacent to the bottom of the stair landing Revise to increase to less than 60 inches (1524 mm) above the landing. 2.2.8 Section R310.1 Emergency escape and rescue opening required Add a second sentence that reads as follows: Cape Cod style attics that qualify as a story shall require one operable emergency and escape opening. 2.2.9 Section 311.7.12 Ships ladders Add the following sentence to the end of the Exception: The device must remain fixed in position when used in these areas. 2.2.10 Section R313 Automatic Fire Sprinkler Systems Delete this section and replace it with the following: An automatic fire sprinkler system shall be installed in one and two family dwellings and townhouses as required by the local jurisdiction where the home will be set. In-plant and final tests required by this Section shall be approved by a certified inspector sition when used in these areas. 2.2.10 Section R313 Automatic Fire Sprinkler Systems Delete this section and replace it with the following: An automatic fire sprinkler system shall be installed in one and two family dwellings and townhouses as required by the local jurisdiction where the home will be set. In-plant and final tests required by this Section shall be approved by a certified inspector. 2.2.11 Section 314.3 (2) Smoke Alarms – Location Revise “immediate vicinity” to read “within 15 feet”. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 15 2.2.12 Section 314.4 Revise “Physical interconnection of smoke alarms shall not be required where listed wireless alarms are installed and…” to “Physical interconnection of smoke alarms shall not be required where listed wireless alarms are installed in existing construction when approved by the Division of Housing and…” 2.2.13 Section 314.6 Smoke Alarms – Power Source Add to the end of the paragraph the following: Smoke and/or carbon monoxide alarms shall not be installed on a circuit dedicated only for smoke and/or carbon monoxide alarms. 2.2.14 Section 315.3 Carbon monoxide alarms – Locations Revise “immediate vicinity” to read “within 15 feet”. 2.2.15 Section 315.6 Carbon monoxide alarms – Power Source Add to the end of the paragraph the following: Smoke and/or carbon monoxide alarms shall not be installed on a circuit dedicated only for smoke and/or carbon monoxide alarms. 2.2.16 Section R802.10 Wood trusses Add the following new section: Section R802.10.5 Marking Each truss shall be legibly branded, marked, or shall have other permanent labeling of the truss drawing’s designated identification number on the large face of the top chord and within two (2) feet of the peak of the truss. 2.2.17 Section R905.1.2 Ice barriers Revise to read as follows: Due to a history of ice forming along eaves in Colorado, an ice barrier is required : Section R802.10.5 Marking Each truss shall be legibly branded, marked, or shall have other permanent labeling of the truss drawing’s designated identification number on the large face of the top chord and within two (2) feet of the peak of the truss. 2.2.17 Section R905.1.2 Ice barriers Revise to read as follows: Due to a history of ice forming along eaves in Colorado, an ice barrier is required. The ice barrier shall consist of a self-adhering polymer-modified bitumen sheet and shall extend from the eave’s edge to a point at least 24” inside the exterior wall line of the building or of not fewer than two layers of underlayment cemented together and to the roof. 2.2.18 Section R1004.4, G2406.2 exceptions 3 and 4, G2425.8 #7, G2445 Delete all and replace with the following: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 16 Unvented fuel fired room heaters and unvented fuel fired fireplaces are prohibited. 2.2.19 Add the following new sections: Section R1001.1and R1004.1 – Fireplaces Every new fireplace must comply with one of the following: 1. Listed and labeled fireplace and chimney systems composed of factory-made components, and assembled in the field in accordance with manufacturer’s instructions and the conditions of the listing, and 2. Approved gas logs. 2.2.20 Section P2503.5.1 Rough plumbing Delete the words “other than plastic” in the sentence for water and air testing. 2.2.21 Chapter 11 ENERGY EFFICIENCY Delete in its entirety. 2.2.22 Section M2001.1 Installation and G2452.2 Installation Add the following sentence: All rooms or spaces containing boilers shall be provided with a floor drain and trap primer. 2.2.23 Section G2417.4.1 Test pressure Revise to read as follows: The test pressure to be used shall not be less than 1 ½ times the proposed maximum working pressure, but not less than 10 psig (69 kPa gauge) for a period of not less than 15 minutes ation and G2452.2 Installation Add the following sentence: All rooms or spaces containing boilers shall be provided with a floor drain and trap primer. 2.2.23 Section G2417.4.1 Test pressure Revise to read as follows: The test pressure to be used shall not be less than 1 ½ times the proposed maximum working pressure, but not less than 10 psig (69 kPa gauge) for a period of not less than 15 minutes. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. The test pressure for valves and connections to appliances shall not exceed 0.5 psig (3kPa). 2.2.24 Electrical Sections Delete Chapters 34 through 43. 2.2.25 Appendix A – Sizing and Capacities of Gas Piping CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 17 Adopted. 2.2.26 Appendix P – Sizing of Water Piping System Adopted. 2.2.27 Appendix AQ – Tiny Houses and Tiny Homes 1. Amend Appendix AQ Tiny Houses as follows: a. AQ101.1 Scope: Change to read: This appendix shall be applicable to tiny houses, and “tiny homes” as defined by section 24-32-3302(35), C.R.S., used as single dwelling units. Tiny houses, and “tiny homes” as defined by section 24-32-3302(35), C.R.S., shall comply with this code except as otherwise stated in this appendix. Insert “…and tiny homes” after each reference to “tiny houses” in all sections of this appendix. b. Add: AQ106.2.7 Tiny homes may use R30 in ceiling insulation to meet the intent of R402.1.2 c. Add: AQ107: Bathroom Lavatory, For Tiny Homes, if a bathroom lavatory cannot be added due to size constraints, then the kitchen sink can be substituted to meet the lavatory requirement. d. Add: AQ108: Construction on a Built-for-Purpose Trailer. The tiny home will be built on a built-for-purpose trailer . Add: AQ106.2.7 Tiny homes may use R30 in ceiling insulation to meet the intent of R402.1.2 c. Add: AQ107: Bathroom Lavatory, For Tiny Homes, if a bathroom lavatory cannot be added due to size constraints, then the kitchen sink can be substituted to meet the lavatory requirement. d. Add: AQ108: Construction on a Built-for-Purpose Trailer. The tiny home will be built on a built-for-purpose trailer. Trailers that have structure modifications prior to the start of the tiny home build must provide engineered stamped drawings and the documentation to be roadworthy on Colorado roads. (Structural modifications may change the trailer classification to a kit trailer or homemade trailer and a new VIN/GVWR and physical inspection by CDOT or Colorado State Highway Patrol, or other approved agencies may be required.) e. Add: AQ109: Tiny Home on a Temporary Foundation. A tiny home on wheels which is installed on a temporary foundation may utilize connections to an electrical pedestal or plumbing connections that allow for movement from one location to another. 2.3 The International Mechanical Code (IMC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 18 2.3.1 Section 303.3.1 LPG appliance Add the following new section: LPG appliances shall not be installed in a pit, basement, or crawl space where unburned fuel may accumulate unless an approved sensing device is installed in conjunction with an automatic shutoff valve located where the gas enters the structure only for retro-fitting of existing structures or as required by the local jurisdiction 8 2.3.1 Section 303.3.1 LPG appliance Add the following new section: LPG appliances shall not be installed in a pit, basement, or crawl space where unburned fuel may accumulate unless an approved sensing device is installed in conjunction with an automatic shutoff valve located where the gas enters the structure only for retro-fitting of existing structures or as required by the local jurisdiction. 2.3.2 Section 903.1 General Add the following additional sentence: Every new installation of a solid fuel-burning, vented decorative appliance or room heater shall meet the most stringent emission standards for wood stoves established under State statute and/or regulations promulgated by the State Air Quality Control Commission as of the time of installation of the appliance or room heater. (Effective January 1, 1991 – CC90-617). 2.3.3 Section 903.3 Unvented gas log heaters Delete this section in its entirety. 2.4 The International Plumbing Code (IPC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and the edition as adopted by the Colorado State Plumbing Board will be the state adopted edition. This code is available through the ICC at: https://www.iccsafe.org. A transition period of 180 days after the effective date applies. The Program Manager for the Building Codes and Standards Section is authorized to grant, in writing, one extension, for a period not more than 180 days. Any conflicts that may arise between these amendments and a future State adopted edition of the IPC shall be resolved by applying the specific amended provisions of the 2021 edition. The following amendments are made to the NEC for use with all factory-built units: 2.4.1 Appendix Chapter E – Sizing of water piping systems 2.4.1.1 Section 312.3 Delete the words “Plastic Piping shall not be tested by using air”. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing ted edition of the IPC shall be resolved by applying the specific amended provisions of the 2021 edition. The following amendments are made to the NEC for use with all factory-built units: 2.4.1 Appendix Chapter E – Sizing of water piping systems 2.4.1.1 Section 312.3 Delete the words “Plastic Piping shall not be tested by using air”. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 19 2.5 The National Electric Code (NEC), published by the National Fire Protection Association, Inc. (NFPA), and the Edition as adopted by the Colorado State Electrical Board at the time of plan submittal. This is a safety code and is available through the NFPA at: https://www.nfpa.org. A transition period of 180 days after the effective date applies. The Program Manager for the Building Codes and Standards Section is authorized to grant, in writing, one extension, for a period not more than 180 days. Any conflicts that may arise between these amendments and a future State adopted edition of the NEC shall be resolved by applying the specific amended provisions of the 2020 edition. The following amendments are made to the NEC for use with all factory-built units: 2.5.1 Article 210.52(A)(2) Wall Space. Add the following exception to the end: Space directly below the island and peninsular countertop and work surfaces are not considered wall space. 2.5.2 Article 210.52(C)(2) Island and Peninsular Countertops and Work Surfaces. Add the following sentence to the end: “Receptacle outlets, other than those installed per 210.52(C)(3) shall not be installed in the space directly below the island or peninsular countertop or work surface. 2.5.3 Article 545 Manufactured Buildings Add the following new section: 2.5.3.1 Section 545.14 Testing (A) Continuity and Operational Tests and Polarity Checks. Each manufactured building shall be subjected to: (1) An electrical continuity test to ensure that all exposed electrically conductive parts are properly bonded; the space directly below the island or peninsular countertop or work surface. 2.5.3 Article 545 Manufactured Buildings Add the following new section: 2.5.3.1 Section 545.14 Testing (A) Continuity and Operational Tests and Polarity Checks. Each manufactured building shall be subjected to: (1) An electrical continuity test to ensure that all exposed electrically conductive parts are properly bonded; (2) An electrical operational test to demonstrate that all equipment, except water heaters and electric furnaces, is connected and in working order; and CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 20 (3) Electrical polarity checks of permanently wired equipment and receptacle outlets to determine that connections have been properly made. These tests shall be performed after branch circuits are complete and after wiring devices are installed and wiring properly terminated. 2.5.4 Article 334.23 Cables Run Across the Top of Floor Joists/Rafters Add the following new sentence at the end: Substantial guard strips or other protection shall be provided to protect wiring within three (3) feet of the marriage line where the attic is exposed and the roof is completed on-site, such as a hinged roof. 2.5.5 Article 210.8(F) Outdoor Outlets Add the following to the existing exception: …than those covered in 210.8(C), and outlets designated for outdoor mechanical cooling equipment. This exception is limited to outdoor mechanical cooling equipment shipped loose by the manufacturer with the factory-built structure to be completed on-site. This exemption does not apply if the outdoor mechanical cooling equipment is provided by any other party. If it is provided by a party that is not the manufacturer of the factory-built structure, then the State Electrical Board’s requirement applies. 2.6 The International Fuel Gas Code (IFGC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org hanical cooling equipment is provided by any other party. If it is provided by a party that is not the manufacturer of the factory-built structure, then the State Electrical Board’s requirement applies. 2.6 The International Fuel Gas Code (IFGC), 2021 Edition, published by the International Code Council, Inc. (ICC). This is a safety code and is available through the ICC at: https://www.iccsafe.org. 2.6.1 Section 303.3 Prohibited locations Add the following: LPG appliances shall not be installed in a pit, basement, or crawl space where unburned fuel may accumulate unless an approved sensing device is installed in conjunction with an automatic shutoff valve located where the gas enters the structure only for retro-fitting of existing structures or as required by the local jurisdiction. 2.6.2 Section 303.3, 501.8 #8, Section 621 Delete all and replace with the following: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 21 Unvented fuel fired room heaters and unvented fuel fired fireplaces are prohibited. 2.6.3 Section 406.4.1 Test pressure Revise to read as follows: The test pressure to be used shall not be less than 1 ½ times the proposed maximum working pressure, but not less than 10 psig (69 kPa gauge), irrespective of design pressure. Where the test pressure exceeds 125 psig (862 kPa gauge), the test pressure shall not exceed a value that produces a hoop stress in the piping greater than 50 percent of the specified minimum yield strength of the pipe. The test pressure for valves and connections to appliances shall not exceed 0.5 psig (3kPa). 2.7 The International Energy Conservation Code (IECC), 2021 Edition, published by the International Code Council, Inc. (ICC). This code is available through the ICC at: https://www.iccsafe.org. 2.7.1 Section R402.4.1.2 Add the following requirement: All air barrier elements shall be installed as detailed in Table 402.4.1.1 for valves and connections to appliances shall not exceed 0.5 psig (3kPa). 2.7 The International Energy Conservation Code (IECC), 2021 Edition, published by the International Code Council, Inc. (ICC). This code is available through the ICC at: https://www.iccsafe.org. 2.7.1 Section R402.4.1.2 Add the following requirement: All air barrier elements shall be installed as detailed in Table 402.4.1.1. and are inspected and verified with a checklist incorporated into the Quality Assurance Inspection Checklist and part of the “finished home” file for the building/dwelling. All elements of the air barrier shall be listed and installed per the manufacturer's installation instructions. A completed air barrier checklist shall be kept on file with the Division of Housing and the manufacturer’s quality assurance program. Construction Standards and Procedures for U.S. Housing and Urban Development (HUD) Homes These standards and procedures are available through HUD at: https://www.hud.gov. Pursuant to sections 24-32-3302(12), 24-32-3302(13), 24-32-3302(20), 24-32-3302(32), 24-32-3305(5), 24-32-3306(1), 24-32-3307(2), 24-32-3309(1)(a), and 24-32-3327, C.R.S., the State Housing Board adopts the following requirements for manufactured homes constructed to the “National Manufacturing Housing Construction and Safety Standards Act of 1974”, 42 U.S.C. sec. 5401 et seq. (manufactured from June 15, 1976 to present): 2.8 Compliance with Title 24: Housing and Urban Development; Subtitle B— Regulations Relating to Housing and Urban Development (Continued); Chapter XX—Office of Assistant Secretary for Housing—Federal Housing Commissioner, Department of Housing and Urban Development; Part 3280—Manufactured Home Construction and Safety Standards, of Title 24. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing pliance with Title 24: Housing and Urban Development; Subtitle B— Regulations Relating to Housing and Urban Development (Continued); Chapter XX—Office of Assistant Secretary for Housing—Federal Housing Commissioner, Department of Housing and Urban Development; Part 3280—Manufactured Home Construction and Safety Standards, of Title 24. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 22 2.9 Compliance with Part 3282—Manufactured Home Procedural and Enforcement Regulations of the same title, subtitle, and chapter in Rule 2.8 above as applied and enforced as the state administrative agency for the federal government. 2.10 Compliance with Part 3286—Manufactured Home Installation Program of the same title, subtitle, and chapter in in Rule 2.8 above, which is inspected and enforced through application of the Division of Housing’s adopted Manufactured Housing Installation Codes. 2.11 Compliance with Part 3288—Manufactured Home Dispute Resolution Program of the same title, subtitle, and chapter in Rule 2.8 above as applied and enforced as the state administrative agency for the federal government. Manufactured Home and Tiny Home Installation Standards These standards and guidelines are available through the Division of Housing in the form of the “Manufactured Home and Tiny Home Installation Handbook” located at: https://www.colorado.gov/dola/division-housing. 2.12 Pursuant to section 24-32-3310, C.R.S., nothing in this rule is intended to interfere with the right of a local jurisdiction to enforce its rules governing the installation of a manufactured home or tiny home as long as those rules are not inconsistent with this rule. Pursuant to section 24-32-3318, C.R.S., a local jurisdiction may not adopt less stringent standards for the installation of a manufactured home or tiny home than those adopted by the Division and may not adopt a different standard without express consent by the Division rules governing the installation of a manufactured home or tiny home as long as those rules are not inconsistent with this rule. Pursuant to section 24-32-3318, C.R.S., a local jurisdiction may not adopt less stringent standards for the installation of a manufactured home or tiny home than those adopted by the Division and may not adopt a different standard without express consent by the Division. However, a local jurisdiction may adopt unique public safety requirements related to geographic or climatic conditions such as weight restrictions for snow loads or wind shear factors subject to the conditions outlined in section 24-32-3318, C.R.S. 2.12.1 Factory-built residential structures (modular) must be installed on a permanent foundation approved through the local jurisdiction. In areas where no building codes have been adopted, the foundation must be designed and approved by a State of Colorado licensed engineer unless plans are approved by the Division and in compliance with its adopted International Residential Code (IRC) foundation prescriptive requirements. 2.13 Primary Standards (required for all new homes): 2.13.1 The current written installation instructions provided by the manufacturer of the home. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 23 2.13.1.1 An installation of a HUD-code home in this state must be performed in strict accordance with the applicable manufacturer's installation instructions. The value of the allowable bearing capacity of the soil the home will rest on must be recorded by the installer on the Installation Authorization form or other Division-approved form and justification for higher values also provided if it is determined to be other than 1,500 psf home in this state must be performed in strict accordance with the applicable manufacturer's installation instructions. The value of the allowable bearing capacity of the soil the home will rest on must be recorded by the installer on the Installation Authorization form or other Division-approved form and justification for higher values also provided if it is determined to be other than 1,500 psf. 2.14 Alternate Standards (for older homes or homes that do not include the manufacturer’s installation instructions) – installation must be in accordance with the following alternate standards adopted by the Division and State Housing Board: 2.14.1 Modular Homes and Tiny Homes 2.14.1.1 Structural attachment requirements approved by a State of Colorado actively licensed engineer. 2.14.1.2 Current version of the International Residential Code (IRC) as adopted by the State Housing Board. 2.14.2 Mobile and HUD-code Homes 2.14.2.1 National Fire Protection Association (NFPA) 225, Model Manufactured Home Installation Standard 2013 Edition, including any revisions, additions, and deletions identified below. 2.14.2.1.1 Section 4.4.4 Site suitability with home design Revise to read as follows: The installer shall verify data plates provided with a HUD-code home prior to installation in the state of Colorado. The data plate shall be matched with the home (serial numbers). The data plate shall indicate the following minimums: Wind Zone: I Thermal Zone: III Roof Load: Middle (30 PSF) CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing with home design Revise to read as follows: The installer shall verify data plates provided with a HUD-code home prior to installation in the state of Colorado. The data plate shall be matched with the home (serial numbers). The data plate shall indicate the following minimums: Wind Zone: I Thermal Zone: III Roof Load: Middle (30 PSF) CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 24 If the data plate does not meet these minimum requirements, the installer shall not set the home. The installer is required to check with the local jurisdiction where the home will be located to determine if it is designed for the area’s proven snow or wind load since some parts of the state are subjected to heavy snow and/or high winds. 2.14.2.1.2 Section 5.3 Fire separation distance Revise to read as follows: Fire separation distances shall comply with local rules or regulations. In their absence, the most current version of the International Residential Code (IRC) as adopted by the Housing Board applies. 2.14.2.1.3 Section 5.5.2 Revise to read as follows: Soil that supports footings and foundations shall be capable of accommodating all loads required by this standard. To help prevent settling or sagging, the foundation must be constructed on firm, undisturbed soil or 90% compacted soil. The design bearing capacity of the soil shall be determined in accordance with Section 5.6. 2.14.2.1.4 Section 5.6 Investigation and Bearing Capacity of Soil Revise as follows: Soils that appear to be composed of peat, organic clays, uncompacted fill, expansive or other unusual conditions shall have a licensed engineer determine the classification and maximum allowable soil bearing capacity. Otherwise the bearing capacity of the soil shall be assumed to be 1,500 psf. A larger bearing capacity for the soil may be used as follows provided the class of soil is known: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing uncompacted fill, expansive or other unusual conditions shall have a licensed engineer determine the classification and maximum allowable soil bearing capacity. Otherwise the bearing capacity of the soil shall be assumed to be 1,500 psf. A larger bearing capacity for the soil may be used as follows provided the class of soil is known: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 25 Sandy gravel and/or gravel, very dense or cemented sands (GW, GP, SW, SP, GM, SM) ------------- 2,000 psf Sedimentary and foliated rock---------------------------- 4,000 psf When a value other than 1,500 psf is determined for the soil bearing capacity it shall be recorded by the installer on the Division of Housing’s Installation Authorization form and justification for higher values shall also be provided. 2.14.2.1.5 Section 5.8.1 Vapor retarder Revise as follows: If the space under the home is to be enclosed with skirting or other material, a vapor retarder that keeps ground moisture out of the home shall be installed unless specifically allowed to be omitted by the authority having jurisdiction. 2.14.2.1.6 Section 5.8.3.2 Revise as follows: The vapor retarder may be placed directly beneath footings, or otherwise installed around or over footings placed at grade, and around anchors or other obstructions. Any voids or tears in the vapor retarder must be repaired. 2.14.2.1.7 Section 6.2.3.1.2 Delete this section. 2.14.2.1.8 Section 6.2.3.1.3.1 Revise as follows: Tables 6.2.3.1.3(a), 6.2.3.1.3(b), and 6.2.3.1.3(c) for pier capacities, as replaced in Appendix A, shall be used when the manufacturer’s installation instructions are not available. 2.14.2.1.9 Section 6.2.3.1.3.2 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing rder must be repaired. 2.14.2.1.7 Section 6.2.3.1.2 Delete this section. 2.14.2.1.8 Section 6.2.3.1.3.1 Revise as follows: Tables 6.2.3.1.3(a), 6.2.3.1.3(b), and 6.2.3.1.3(c) for pier capacities, as replaced in Appendix A, shall be used when the manufacturer’s installation instructions are not available. 2.14.2.1.9 Section 6.2.3.1.3.2 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 26 Revise as follows: Manufactured piers shall be rated at least to the capacities given in Tables 6.2.3.1.3(a), 6.2.3.1.3(b), and 6.2.3.1.3(c), as replaced in Appendix A, and locally constructed piers shall be designed to transmit these loads safely as required by 6.2.3.2. 2.14.2.1.10 Section 6.2.3.2.2.2 Revise as follows: Caps shall be of solid masonry of at least 4 in. (100 mm) nominal thickness, or of treated or hardwood dimensional lumber at least 2 in. (50mm) nominal thickness, or of ½” thick steel. 2.14.2.1.11 Section 6.2.3.2.3.1 Revise as follows: Nominal 4 in. x 6in. (100mmx 150mm) hardwood shims shall be used to level the home and fill any gaps between the base of the I-beam and the top of the pier cap. Any of the following hardwood species may be used: Ash, Beech, Birch, Hickory, Oak, Rock Elm, Black or Red Maple, or Sweetgum. 2.14.2.1.12 Section 6.2.3.2.3.3 Revise as follows: Hardwood (species identified in the amendment to Section 6.2.3.2.3.1 above) or treated wood plates shall be used to fill in any remaining vertical gap no thicker than 2”. The maximum total gap to be filled with shims and plates shall be 2”. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing , Rock Elm, Black or Red Maple, or Sweetgum. 2.14.2.1.12 Section 6.2.3.2.3.3 Revise as follows: Hardwood (species identified in the amendment to Section 6.2.3.2.3.1 above) or treated wood plates shall be used to fill in any remaining vertical gap no thicker than 2”. The maximum total gap to be filled with shims and plates shall be 2”. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 27 2.14.2.1.13 Section 6.2.5.5 Revise as follows: All homes. Supports shall be placed on both sides of side wall exterior doors and any other side wall openings greater than 48 in. (such as entry and sliding glass doors), and under porch posts, factory installed fireplaces and wood stoves. Size perimeter piers under openings based on Table 6.2.3.1.3(b), as replaced in Appendix A, “Exterior wall” where the actual side wall opening shall be less than or equal to the spacing selected from the table. Homes requiring perimeter blocking. Refer to Figure 6.2.5.3 and Figure 6.2.5.4 and Table 6.2.3.1.3(b), as replaced in Appendix A, for homes requiring perimeter blocking in addition to sidewall opening blocking described above. 2.14.2.1.14 Section 6.3.1.2.2 Delete this section. 2.14.2.1.15 Section 6.5.2 Delete this section. 2.14.2.1.16 Section 7.2 Revise as follows: The home shall be installed and leveled by installation personnel approved by the State of Colorado to install manufactured homes. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing ocking in addition to sidewall opening blocking described above. 2.14.2.1.14 Section 6.3.1.2.2 Delete this section. 2.14.2.1.15 Section 6.5.2 Delete this section. 2.14.2.1.16 Section 7.2 Revise as follows: The home shall be installed and leveled by installation personnel approved by the State of Colorado to install manufactured homes. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 28 2.14.2.1.17 Section 7.3 Revise as follows: The interconnection of multi-section homes shall be completed in accordance with the manufacturer’s installation instructions. When the manufacturer’s installation instructions are not available, the interconnection of multi-section homes shall be in accordance with Table 7.3, as provided in Appendix A, or per the requirements approved by a State of Colorado licensed engineer. 2.14.2.1.18 Section 7.5 Anchoring Instructions Section 7.5.1 Security against the wind Section 7.5.1.1 Revise as follows: After blocking and leveling, the installer shall secure the manufactured home against wind per Section 7.5.2 or Section 7.5.3. Anchorage shall be for Wind Zone I. Homes that are designed for Wind Zone II and III must be anchored per the Manufacturer’s Installation Instructions or the requirements of a professional engineer. 2.14.2.1.19 Section 7.5.2 Proprietary Anchorage Systems Add the following: A proprietary anchorage system may be used to resist overturning and lateral movement (sliding) caused by wind as long as it complies with all of the following: 1. The system shall be listed by a nationally recognized third-party agency for anchoring manufactured homes. 2. The system shall be evaluated and approved by a licensed professional engineer. 3. The system shall be recognized as acceptable for use by the Division of Housing. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing d by wind as long as it complies with all of the following: 1. The system shall be listed by a nationally recognized third-party agency for anchoring manufactured homes. 2. The system shall be evaluated and approved by a licensed professional engineer. 3. The system shall be recognized as acceptable for use by the Division of Housing. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 29 4. The installer shall follow the requirements in the anchorage system installation instructions. 2.14.2.1.20 Section 7.5.3 Ground Anchor System Section 7.5.3.1 Specifications for Tie-Down Straps and Anchors Add the following: Straps and anchors are to have corrosion protection at least equivalent to that provided by a coating of zinc on steel of not less than 0.30 oz/ft2 of surface coated. Straps and anchoring equipment must be capable of resisting a minimum ultimate load of 4,725 lbs and a working load of 3,150 lbs as installed; determined by a licensed professional engineer, architect or tested by a nationally recognized third- party agency. Straps are to be 1.25”x0.035” or larger steel strapping conforming to ASTM D 3953, Type 1, Grade 1, Finish B. Anchors are to be installed in accordance with their listing or certification to their full depth. 2.14.2.1.21 Section 7.5.3.2 Number and Location of Anchors Section 7.5.3.2.1 Transverse Anchorage Add the following: The number and location of anchors and anchor straps for securing single-section and multi-section manufactured homes in the transverse direction shall conform to the manufacturer’s installation instructions. When relocating the home or when the manufacturer’s installation instructions are not available, the number and location of anchors and anchor straps shall conform to Table 7.5.3.2.1, Figure 7.5.3.2.1(a), and Figure 7.5.3.2.1(b), as provided in Appendix A. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing sverse direction shall conform to the manufacturer’s installation instructions. When relocating the home or when the manufacturer’s installation instructions are not available, the number and location of anchors and anchor straps shall conform to Table 7.5.3.2.1, Figure 7.5.3.2.1(a), and Figure 7.5.3.2.1(b), as provided in Appendix A. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 30 2.14.2.1.22 Section 7.5.3.2.2 Longitudinal Anchorage Add the following: The number and location of anchors and anchor straps for securing single-section and multi-section manufactured homes in the longitudinal direction shall conform to the manufacturer’s installation instructions. When relocating the home or when the manufacturer’s installation instructions are not available, the number and location of longitudinal anchors and anchor straps shall conform to Table 7.5.3.2.2 and Figure 7.5.3.2.1(a), as provided in Appendix A. 2.14.2.1.23 Section 7.5.3.2.3 Anchor Installation Add the following: The installed ground anchor type and size/length must be listed for use in the soil class at the site and for the minimum and maximum angle permitted between the diagonal strap and the ground and all ground anchors must be installed in accordance with their listing or certification and the ground anchor manufacturer installation instructions. Unless the foundation system is frost-protected to prevent the effects of frost heave, the ground anchors shall be installed below the frost line. Ground anchor stabilizer plates shall be installed in accordance with the anchor and plate manufacturer installation instructions. 2.14.2.1.24 Section 7.5.3.2.4 Side wall or over the roof straps Add the following: If sidewall, over-the-roof, mate-line, or shear wall straps are installed on the home, they must be connected to an anchoring assembly. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing stabilizer plates shall be installed in accordance with the anchor and plate manufacturer installation instructions. 2.14.2.1.24 Section 7.5.3.2.4 Side wall or over the roof straps Add the following: If sidewall, over-the-roof, mate-line, or shear wall straps are installed on the home, they must be connected to an anchoring assembly. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 31 2.14.2.1.25 Section 7.6.3 Expanding Rooms Revise as follows: Expanding rooms shall be installed in accordance with the manufacturer’s instructions. When the manufacturer’s instructions are not available, perimeter blocking shall be installed in accordance with Table 6.2.3.1.3(b), as replaced in Appendix A, and anchors shall be installed in accordance with Section 7.5.3.2. 2.14.2.1.26 Section 7.7.4.2 Revise (2) as follows: (2) Walls-200. 2.14.2.1.27 Section 8.1 Installation of Site-Installed Features Revise as follows: Carports, awnings, porches, roof covers, and other similar attachments or additions shall not be supported by a manufactured home unless the home was specifically designed to accommodate such attachments or the attachment is designed by a licensed professional engineer. Non-structural connections for flashings and coverings at the junction are acceptable. 2.14.2.1.28 Section 8.4 Delete this section. 2.14.2.1.29 Section 8.8.3 Revise as follows: Access opening(s) not less than 18 inches in width and 24 inches in height must be provided and located so that any utility connections are accessible. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing gineer. Non-structural connections for flashings and coverings at the junction are acceptable. 2.14.2.1.28 Section 8.4 Delete this section. 2.14.2.1.29 Section 8.8.3 Revise as follows: Access opening(s) not less than 18 inches in width and 24 inches in height must be provided and located so that any utility connections are accessible. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 32 2.14.2.1.30 Section 8.9 Telephone and Cable TV Revise as follows: Telephone, cable TV, and similar wiring shall be installed per the Authority Having Jurisdiction (AHJ) requirements and the National Electric Code (NEC). 2.14.2.1.31 Section 9.4 Range, Cooktop, Oven Venting, and other Fixtures or Appliances Add new Section 9.4.3 to read as follows: If other fixtures or appliances are to be site-installed, follow the manufacturer’s installation instructions. Use only products listed for manufactured homes and follow all applicable local codes. 2.14.2.1.32 Section 9.7 Furnace, Water Heater, and other Fuel Fired Appliances Add this new section to read as follows: Verify appliance is installed per the manufacturer’s installation instructions including any combustion air requirements. Verify flues are in place and are properly connected and extend through the roof with flashing and caps. 2.14.2.1.33 Section 10.4.2 Orifices and Regulations Revise as follows: Before making any connection to the site supply, the inlet orifices of all gas-burning appliances shall be checked to ensure they are correctly set-up for the type of gas to be supplied and are sized correctly for the altitude above sea level where the home is set. The manufacturer’s installation instructions for the appliance shall be followed. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing ng any connection to the site supply, the inlet orifices of all gas-burning appliances shall be checked to ensure they are correctly set-up for the type of gas to be supplied and are sized correctly for the altitude above sea level where the home is set. The manufacturer’s installation instructions for the appliance shall be followed. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 33 2.14.2.1.34 Chapter 11 Life Safety Features Revise as follows: 2.14.2.1.34.1 Smoke Alarms Verify smoke alarms are installed to protect the living area, rooms designed for sleeping, on upper levels, and in the basement for homes installed over a basement. Verify smoke alarms are installed and operating properly to meet the requirements of 24 CFR 3280. 2.14.2.1.34.2 Carbon Monoxide Alarms An approved carbon monoxide alarm shall be installed outside of each separate sleeping area within 15 feet of the entrance to the bedrooms in dwelling units within which fuel-fired appliances are installed and in dwelling units that have attached garages. 2.14.2.1.34.3 Fire Separation Distance Fire separation distances shall comply with local rules or regulations. In their absence, the most current version of the International Residential Code (IRC) as adopted by the State Housing Board, shall apply. 2.14.2.2 Permanent Foundations Guide for Manufactured Housing (4930.3G), , published by the U.S. Department of Housing and Urban Development (HUD), including any revisions, additions, and deletions identified below, or the most recent version. 2.14.2.2.1 Appendix B – Foundation Design Load Tables Revised as follows: In the multi-section tables under the marriage wall opening width (ft.), the values given for required effective footings area – Aftg (sq.ft.), shall be divided by 2. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing including any revisions, additions, and deletions identified below, or the most recent version. 2.14.2.2.1 Appendix B – Foundation Design Load Tables Revised as follows: In the multi-section tables under the marriage wall opening width (ft.), the values given for required effective footings area – Aftg (sq.ft.), shall be divided by 2. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 34 2.15 ICC/MBI 1200 – 2021 Standard for Off-site Construction: Planning, Design, Fabrication and Assembly. LINK 2.16 ICC/MBI 1205 – 2021 Standard for Off-site Construction: Inspection and Regulatory Compliance. LINK 2.17 ICC/MBI 1210 – 2023 Standard for Mechanical, Electrical, Plumbing Systems, Energy Efficiency and Water Conservation in Off-site Construction. LINK 2.18 ICC 2023 G6 Guideline on Advanced Panelization for Buildings. LINK 2.19 Colorado Model Electric Ready and Solar Ready Code. LINK 2.20 Upon written request, the Division of Housing will consider modifications to the standards or alternate materials and methods of construction. The Division of Housing will require that sufficient evidence or proof be submitted to support and substantiate the modification or alternate request. 2.20.1 The Division of Housing may approve any such modification or alternate, provided the Division of Housing finds that the proposed modification or alternate conforms with the intent and purpose of the standards and is equivalent in suitability, strength, effectiveness, durability, safety, and sanitation. 2.20.2 The approval of any modification and/or alternate by the Division of Housing will be made in writing and is required prior to commencing the work in question te, provided the Division of Housing finds that the proposed modification or alternate conforms with the intent and purpose of the standards and is equivalent in suitability, strength, effectiveness, durability, safety, and sanitation. 2.20.2 The approval of any modification and/or alternate by the Division of Housing will be made in writing and is required prior to commencing the work in question. 2.20.3 In the event that a local jurisdiction has declared a state of emergency, and met the written request and evidence or proof submitted to support and substantiate the request as stated in Rule 2.20, and provided the Division of Housing makes the findings required by Rule 2.20.1, the Division may for a period of 180 days allow a modification to the standards, or alternate materials and methods of construction. Additional 180 day extensions may be requested in writing by the local jurisdiction to DOH. Requests from the local jurisdiction should include a copy of the approved local jurisdiction codes and explanation of the requested changes and any site specific information. Requests will not be accepted that are more stringent than the current adopted codes. These structures will receive an Emergency Response Unit insignia from the Division of Housing. Rule 3. Fees. Pursuant to sections 24-32-3309(1)(a), 24-32-3315(5), and 24-32-3323(3), C.R.S., the State Housing Board establishes the following schedule of fees, which are not subject to refund, are due in advance, and must accompany the appropriate application, except for certain inspection fees: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 35 3.1 Annual registration fees: 3.1.1 Plant/Manufacturer: $773.00 3.1.1.1 Plant/Manufacturer Three Year $2,319.00 3.1.2 Inspection Agency: $322.00 3.1.3 Seller: $200.00 3.1.4 Installer (Individual or business): ject to refund, are due in advance, and must accompany the appropriate application, except for certain inspection fees: CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 35 3.1 Annual registration fees: 3.1.1 Plant/Manufacturer: $773.00 3.1.1.1 Plant/Manufacturer Three Year $2,319.00 3.1.2 Inspection Agency: $322.00 3.1.3 Seller: $200.00 3.1.4 Installer (Individual or business): $250.00 3.1.4.1 A business entity will pay an initial annual registration fee of $250. The annual renewal fee shall be $250. Additional qualifying individuals may be added to the business entity registration during the annual registration cycle for a processing fee of $100. Addition of additional qualified individuals will not change the renewal cycle of business entity installer registration. 3.1.5 Independent Inspector: $450.00 3.1.6 Late re-registration fee $125.00 3.2 Plan checking fees: 3.2.1 Finished space: $0.32 per sq. ft. ($100 min.) 3.2.2 Unfinished space (attics, lofts, garages, etc.): $0.13 per sq. ft. 3.3 Supplemental plan check fee (renewal, etc.): $0.13 per sq. ft. ($100 min.) 3.3.1 2nd Resubmittal Plan Check Fee $127.00 3.3.2 Revision Fee $75 per hour ($100 min) 3.4 Third party oversight plan check fee (includes audits): $0.19 per sq. ft. ($150 min.) 3.5 Insignia fees: 3.5.1 Primary Insignia: $161.00 3.5.2 Additional Floor Tag: $161.00 3.5.3 Inspection-only Tag: $161.00 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 36 3.5.4 Component-only Insignia: $161.00 3.5.5 Modification Insignia: $161.00 3.5.6 Installation Insignia (free for participating jurisdictions): $78.00 3.6 Inspection fees: 3.6.1 In-Plant/Factory inspection fee: nsignia fees: 3.5.1 Primary Insignia: $161.00 3.5.2 Additional Floor Tag: $161.00 3.5.3 Inspection-only Tag: $161.00 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 36 3.5.4 Component-only Insignia: $161.00 3.5.5 Modification Insignia: $161.00 3.5.6 Installation Insignia (free for participating jurisdictions): $78.00 3.6 Inspection fees: 3.6.1 In-Plant/Factory inspection fee: $438.00 per inspection 3.6.2 Oversight inspection fee, including re-inspections: $348.00 per inspection/address (A) An additional Multi-Box fee is required if the unit has more than 3 boxes – add $32.00 per box. (B) Multi-family IBC Inspection Fee $348 per dwelling unit plus an additional multi-box fee is required if the unit has more than 3 boxes – add $32 per box. An all-day (up to 8 hours) fee may be determined if necessary. Multi-day fees will require extra fees for lodging/food. 3.6.3 Special inspection fee: (A) In-State: $75.00 per hour, per inspection, plus trip expenses of travel, food, lodging, parking, car-rental, etc., as allowed in state fiscal rules for per diem and travel. (B) Out-of-State units manufactured in Colorado: $438.00 per inspection/unit 3.6.4 Modification inspection fee: $219.00 3.6.5 Installation inspection fee (residential): (A) Final or Foundation (Rough or Final): $258.00 Additional box fee if more than three units (B) Re-inspection fee: $258.00 (C) Multi-family Installation Fee $348.00 per building plus an additional multi-box fee is required if the building has more than 3 boxes – add $32 per box. An all-day (up to 8 hours) fee may be determined if necessary. Multi-day fees will require extra fees for lodging/food. (D) Installation Authorization Fee $25.00 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 37 3.6.6 Non Compliance/Prohibited Sale/Red Tag fee: $322.00 3.6.7 Cancelled Inspection fee – same day e is required if the building has more than 3 boxes – add $32 per box. An all-day (up to 8 hours) fee may be determined if necessary. Multi-day fees will require extra fees for lodging/food. (D) Installation Authorization Fee $25.00 CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 37 3.6.6 Non Compliance/Prohibited Sale/Red Tag fee: $322.00 3.6.7 Cancelled Inspection fee – same day Full fee 3.7 Certificate of Occupancy fee (only applies to hotels, motels, and multi-family structures in those areas of the state where no standards exist): $161.00 3.8 Waiver of fees: 3.8.1 Pursuant to section 24-32-3315(7)(a), the Division of Housing does not charge for certification of installers. 3.8.2 The Division of Housing waives the fee for certification of an independent inspector. 3.8.3 The Division of Housing does not charge for installer or inspector exams. 3.8.4 The Division of Housing may waive fees for plan reviews and unit certifications that are subsidized under local, state, or federal housing programs for low-income households, and being constructed by the State of Colorado, a local government, or a nonprofit agency. 3.8.5 The Division of Housing waives the insignia fee for local jurisdictions that perform installation inspections as authorized participating jurisdictions. 3.9 As-built structures 3.9.1 As-built structures will be charged double the respective fee for each unit if found to not have gone through the proper approved procedures here within these rules for plan approval, manufacturer registration, inspections, or reporting. Rule 4. Factory-Built Residential Structures (Modular and Tiny Homes) and Non-Residential Structures (Commercial) Requirements 4.1 Every “factory-built structure” as defined in section 24-32-3302(11), C.R.S., that is manufactured, sold, offered for sale, or occupied in this state must display an insignia issued by the Division of Housing certifying that the structure is constructed in compliance with the codes adopted by the State Housing Board dular and Tiny Homes) and Non-Residential Structures (Commercial) Requirements 4.1 Every “factory-built structure” as defined in section 24-32-3302(11), C.R.S., that is manufactured, sold, offered for sale, or occupied in this state must display an insignia issued by the Division of Housing certifying that the structure is constructed in compliance with the codes adopted by the State Housing Board. This does not apply to factory-built structures manufactured or sold for transportation to and installation in another state. However, if the unit were to return to Colorado for use, then it would require an insignia issued by the Division of Housing. To assist with the certification process, pursuant to section 24-32- 3303(1)(a), C.R.S., a “manufacturer” as defined in section 24-32-3302(23), C.R.S., is required to be “registered” (based on qualifications) or “certified” (based on performance) with the Division of Housing. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 38 4.1.1 Registration or certification is for a specific manufacturing facility location, and is not transferable to any other location including those of the same manufacturer. 4.1.2 A registered or certified manufacturer is required to inform the Division of Housing of a change in ownership, address, or location within ten (10) business days of such change. 4.1.3 Tiny Homes built for personal use, not to be sold, and not to be permanently installed outside the jurisdiction site location within 1 year of the date it received certification for construction, may be inspected and certified for construction and installation. Must be built to the Division of Housing approved Rules and inspected at all stages of construction by the local authority acting as a third party agency approved by the Division of Housing or inspected by the Division of Housing at all phases of construction tion within 1 year of the date it received certification for construction, may be inspected and certified for construction and installation. Must be built to the Division of Housing approved Rules and inspected at all stages of construction by the local authority acting as a third party agency approved by the Division of Housing or inspected by the Division of Housing at all phases of construction. The approval does not guarantee local approval in jurisdictions outside of the certifying jurisdiction, please check those local codes and ordinances prior to relocating outside the jurisdiction of approval. 4.1.3.1 Limited to one structure per household. More than one structure will be considered manufacturing and must register as a manufacturer per Rule 4. 4.1.4 Tiny Homes built for personal use and only intended for use within the jurisdiction it is built in, is regulated by the local building department, follows the local codes and ordinances, and will not be certified by the Division as a state approved structure. 4.2 Registered/Certified manufacturers are required to have that facility’s production approved through an initial review of its Quality Control (QC) program and the Quality control personnel that ensure construction code compliance. The Division of Housing must be notified of any changes to the QC program or personnel. 4.3 The manufacturer’s QC department must perform “no cover” inspections for all phases of construction on all structures and witness all required tests, regardless of whether the facility is registered or certified. 4.4 Upon the manufacturer’s receipt of the approved plans and manual, the third party agency may proceed with QA, rough, and final inspections with registered manufacturers, or if the manufacturer is certified, to include factory oversight inspections. 4.5 Manufacturers who sell direct to purchasers of one or two family dwellings must register as a Seller with the Division of Housing and follow all statutory and Administrative Rules requirements. See Rule 5. manual, the third party agency may proceed with QA, rough, and final inspections with registered manufacturers, or if the manufacturer is certified, to include factory oversight inspections. 4.5 Manufacturers who sell direct to purchasers of one or two family dwellings must register as a Seller with the Division of Housing and follow all statutory and Administrative Rules requirements. See Rule 5. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 39 4.5.1 The exception is if the purchaser is a developer who in turn plans to resell the home to the end-user; the developer in that scenario is required to be a registered seller with the Division of Housing. 4.5.2 Manufacturers who receive down payments or deposits from registered sellers or directly from intended home-owners, must provide the following protections for down payments in excess of the cost of materials, construction, design, and administration of the specific home ordered by the consumer: (1) Provide to the Division of Housing a letter of credit or surety bond in the amount of $100,000 which the Division of Housing may call upon after an enforcement action for cancellation or failure to deliver a unit when the down payment is not returned. (2) Make available to the Division of Housing upon request an accounting of deposits received, and amounts spent for materials, construction, design and administration for each unit from time of deposit received to delivery of the unit IF the Division requests this information as part of an audit to verify compliance. 4.6 In order to provide efficiency, manufacturers building multi-family or commercial units as a part of a development project of 5 or more units must contact the Division of Housing and provide a project plan that includes: project schedule, production schedule, on-site construction items, and installation plan and schedule. It is recommended to contact the Division of Housing early in the plan process, even before all the required documents are available ulti-family or commercial units as a part of a development project of 5 or more units must contact the Division of Housing and provide a project plan that includes: project schedule, production schedule, on-site construction items, and installation plan and schedule. It is recommended to contact the Division of Housing early in the plan process, even before all the required documents are available. The Division will evaluate the materials provided, meet with the respective parties, and determine a total estimated fee schedule. Overnight stays by inspectors may require additional expenses. Following the installation, it is recommended that a follow up meeting be conducted with all applicable parties to check the status of the project plan. Manufacturer Registration 4.7 Once issued by the Division of Housing’s Building Codes & Standards Section, a registration is active for one (1) year or three (3) years after completing the first year and must be successfully renewed in order to continue manufacturing structures in the state of Colorado or shipping them into the state. Three year registrations will require an email or letter regarding any material changes (or no changes) to operations annually. For three year registrations, it is the responsibility of the manufacturer to ensure annual payment is paid in a timely manner or forfeit the remaining registration period. Notifications are only sent as a courtesy, for all registration types, when the Registration period is going to expire at 60 days and 30 days prior to the expiration date and when it expires. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing , it is the responsibility of the manufacturer to ensure annual payment is paid in a timely manner or forfeit the remaining registration period. Notifications are only sent as a courtesy, for all registration types, when the Registration period is going to expire at 60 days and 30 days prior to the expiration date and when it expires. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 40 4.8 At the time of registration, all manufacturers are required to have Division of Housing approval, in writing, of the third party agency or agencies that will conduct the production inspections and certification of Colorado units on behalf of the Division of Housing. A manufacturer is also required to request approval of the Division of Housing thirty (30) days prior to any subsequent change of its third party agency. Certified Manufacturer Status 4.9 A manufacturer must maintain an active Colorado registration for each manufacturing facility requesting Certified status. 4.9.1 Out of state registered manufacturers must utilize a third party agency to submit a recommendation for certified manufacturer status to the Division of Housing. 4.9.2 In-state registered manufactures may utilize a third party agency to submit a certified manufacturer recommendation OR request certified manufacturer status from the Division of Housing. 4.9.3 Each manufacturing location will require a separate certified manufacturer recommendation. 4.9.4 The Division of Housing and authorized third party agencies will utilize the following criteria for approval of registered manufacturers requesting certified manufacturer status. (A) Verify accountable personnel are capable of identifying and addressing non-conforming items. (B) Verify that training has been achieved for all accountable personnel. (C) Verify an established and functioning quality assurance program (D) Verify that the last three units delivered to Colorado have completed production in compliance of (A), (B), and (C) above ting certified manufacturer status. (A) Verify accountable personnel are capable of identifying and addressing non-conforming items. (B) Verify that training has been achieved for all accountable personnel. (C) Verify an established and functioning quality assurance program (D) Verify that the last three units delivered to Colorado have completed production in compliance of (A), (B), and (C) above. 4.9.5 Manufactures who previously qualified for the Division of Housing’s Certified Factory Status may continue with this status for one year, but are required to complete the new certified manufacturer status by July 1, 2024. 4.9.6 Recommendations received from a third party agency will be reviewed, and if deemed compliant, approved by the Division of Housing and a letter will be sent to the recommending agency, the certified manufacturer and the third party agency doing production inspections. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 41 4.10 All certified manufacturers are registered manufacturers and must follow all registered manufacturer requirements unless specifically exempted or changed in these rules. 4.11 Certified manufacturer status for a specific facility is considered ongoing unless the manufacturer fails to perform as described in 4.12. An annual letter will be required from the manufacturer regarding any changes, or stating no changes, in the quality assurance program in order to continue certified manufacturer status. 4.12 The Division of Housing may immediately seek summary suspension to remove the designation of certified manufacturer status for failure to remedy any of the following conditions after notice from the Division of Housing: 4.12.1 The change of a third party agency or change in that entity’s status. 4.12.2 The change of a facility location. 4.12.3 The manufacturer has had insignias of approval removed pursuant to Division of Housing procedures k summary suspension to remove the designation of certified manufacturer status for failure to remedy any of the following conditions after notice from the Division of Housing: 4.12.1 The change of a third party agency or change in that entity’s status. 4.12.2 The change of a facility location. 4.12.3 The manufacturer has had insignias of approval removed pursuant to Division of Housing procedures. 4.12.4 Failure to remedy manufacturing defects or deficiencies as identified by the Division of Housing and failure to provide a quality assurance program update on corrective actions taken to remedy identified defects or deficiencies. 4.12.5 Notification by a third party agency regarding failure to meet quality control guidelines. 4.12.6 The factory is not in compliance with “Performance Criteria for Monitoring Manufacturers and Third Party Inspection Agencies”. 4.12.6.1 The “Performance Criteria for Monitoring Manufacturers and Third Party Inspection Agencies” utilizes a combination of qualitative analysis based on deficiencies identified during inspection, qualitative analysis based on systematic failures and recurring serious deficiencies, 4.13 A registered manufacturer whose status as a certified manufacturer has been removed by the Division of Housing will resume operations on a higher frequency of inspections until its performance improves and is recommended for reinstatement of its certified manufacturer status pursuant to Rule 4.9 of these rules. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing ious deficiencies, 4.13 A registered manufacturer whose status as a certified manufacturer has been removed by the Division of Housing will resume operations on a higher frequency of inspections until its performance improves and is recommended for reinstatement of its certified manufacturer status pursuant to Rule 4.9 of these rules. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 42 Renewal 4.14 Each manufacturer is required to resubmit its quality control manual (and when applicable, plans) for approval prior to the registration expiration date that is stamped on the quality control manual. This Quality Control manual resubmission is required regardless of when plans are approved or structures shipped. Failure to comply with this requirement will result in that manufacturer’s registered location having to comply with the initial registration inspection requirements. 4.14.1 The registration expiration date for all manufacturers is determined by the expiration date that is stamped on the quality control manual. Plans that are submitted at the time of registration or within the registration period shall have the same expiration date as the quality control manual. 4.14.2 It is the responsibility of the manufacturer to submit to the Division of Housing the quality control manual for approval within the authorized sixty (60) day renewal window prior to the expiration date. Plan Review 4.15 All registered or certified manufacturers must obtain prior approval of each set of designs from the Division of Housing or third party agency before constructing structures under those plans. 4.15.1 The Division of Housing will expedite the review and approval of plans from registered or certified manufacturers whose plans have been reviewed and pre-approved by a third party agency who accepts responsibility and liability in ensuring compliance with requirements of these rules and applicable codes vision of Housing or third party agency before constructing structures under those plans. 4.15.1 The Division of Housing will expedite the review and approval of plans from registered or certified manufacturers whose plans have been reviewed and pre-approved by a third party agency who accepts responsibility and liability in ensuring compliance with requirements of these rules and applicable codes. 4.15.2 Life safety corrections will be sent back to the manufacturer and the third party agency that pre-approved the plans. Third party agencies who continue to pre-approve plans after notification of life safety plan corrections must provide a report on internal quality assurance corrective actions taken to the Division of Housing. 4.15.3 The Division of Housing and third party agencies will utilize redline comments for minor changes and corrections. 4.16 Plan approvals are granted to a manufacturer for a specific manufacturing facility and are not transferable to other manufacturing facilities including those of the same manufacturer. 4.17 Applications for plan review and approval must be submitted electronically to the Division of Housing and must be accompanied by the appropriate fees from Rule 3 of these rules. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 43 4.17.1 The application must include the quality control manual; it must meet or exceed the minimum requirements as specified by the Division of Housing. 4.17.1.1 On-site Construction (OC) as defined in Rule 1.21 of these rules, must be clearly denoted on the submitted plans for determination of the model as an “OC)” structure. The manufacturer is required to follow the Division of Housing “On-site Construction Procedures” when the model is determined to be an OC. Determination of a model as an OC may happen during plan approval or after plan approval 7.1.1 On-site Construction (OC) as defined in Rule 1.21 of these rules, must be clearly denoted on the submitted plans for determination of the model as an “OC)” structure. The manufacturer is required to follow the Division of Housing “On-site Construction Procedures” when the model is determined to be an OC. Determination of a model as an OC may happen during plan approval or after plan approval. 4.17.2 All applications must list an officer of the manufacturer that is in a responsible position with the authority to commit the manufacturer to comply with the rules and regulations that govern the regulation of its factory-built structures and tiny homes. 4.17.3 Factory-built structure and tiny home plans will meet any unique local government standards regarding wildfire risk. 4.17.4 Plans are approved only for a specific address unless the climatic and geographic design and wildfire risk conditions are equal to or less stringent than what was approved. 4.17.4.1 Should the program approve zones, regions, or designates certain areas for modular or tiny home construction, the applicable climatic, geographic design, and wildfire risk for the zone will be approved for any location within the zone, region or designated area. Specific address location will be provided by the manufacturer or registered seller before the home is installed. 4.17.5 Multi-family plans submitted for review must include the applicable sections required by the Division of Housing plan review checklist icable climatic, geographic design, and wildfire risk for the zone will be approved for any location within the zone, region or designated area. Specific address location will be provided by the manufacturer or registered seller before the home is installed. 4.17.5 Multi-family plans submitted for review must include the applicable sections required by the Division of Housing plan review checklist. Included in that submittal, the plans must have a separate section that clearly describes the details for the installation of that building including but not limited to structural connection hardware and fasteners, sheer wall schedules, hold down schedules, plating and drag requirements and all connections that need to be inspected during the setting of the modular units, and must provide a separate manufacturer installation handbook that is clearly referenced on the cover sheet of the plan set, preferably where the building codes are referenced. 4.18 An application will expire and all fees forfeited if it is not completed within 120 days of the initial application date. 4.18.1 Expired applications must be resubmitted as new applications electronically with documentation and fees. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 44 4.19 In order to be considered approved, plans and quality control manuals must be stamped by the Division of Housing or third party agency. Revisions, additions, or deletions will not be acceptable without prior approval. 4.19.1 An approved copy of the quality control manual and plan must be retained at the place of manufacture. 4.19.1.1 They must be kept on file within the specific location of manufacture for the purpose of construction and inspection by Division of Housing inspectors or the third party agency. 4.19.2 All third party agency approvals must be submitted to the Division of Housing for review and oversight approval. 4.20 Plan approval does not guarantee a manufactured structure constructed from the approved plan will also be approved on file within the specific location of manufacture for the purpose of construction and inspection by Division of Housing inspectors or the third party agency. 4.19.2 All third party agency approvals must be submitted to the Division of Housing for review and oversight approval. 4.20 Plan approval does not guarantee a manufactured structure constructed from the approved plan will also be approved. All structures must also undergo an inspection and receive an insignia of approval in order to be considered certified by the State of Colorado. A plan approval does not prevent the Division of Housing or the third party agency from requiring the correction of errors found in the plans or the unit itself, when found in violation of these rules. 4.21 Revisions to the approved plan are required where the manufacturer proposes a change in structural, plumbing, heating, electrical, or fire life safety systems. Such changes must become part of the approved plan unless the Division of Housing determines that the change constitutes a new model. If determined a new model, the interim change will be processed as a new application. Any difference in fees will also be assessed. 4.22 The Division of Housing will approve unchanged plan renewals it previously reviewed and approved, provided there has been no change in adopted codes and the manufacturer’s officer in Rule 4.17.2 above certifies in writing that the plans are identical to those previously approved by the Division of Housing. A “Supplemental Plan Check Fee” will apply for plan renewals. 4.22.1 Should it be determined by the Division of Housing that unauthorized changes have been made to an approved plan, the manufacturer will be subject to a “Red Tag Fee” for every structure built to the changed plans, and the Division may require additional inspections to ensure the code compliance of the structures vision of Housing. A “Supplemental Plan Check Fee” will apply for plan renewals. 4.22.1 Should it be determined by the Division of Housing that unauthorized changes have been made to an approved plan, the manufacturer will be subject to a “Red Tag Fee” for every structure built to the changed plans, and the Division may require additional inspections to ensure the code compliance of the structures. 4.23 When amendments to these regulations require changes to be made to an approved plan, the Division of Housing will notify the manufacturer of the requirement and allow it a reasonable time to submit revised plans for review and approval. Revised plans will be processed as interim changes with the appropriate fees assessed. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 45 4.24 Approved plans expire with the factory registration. Plans must be resubmitted and the Supplemental Plan Check Fee will apply. New plans approved within 120 days of the manufacturers’ registration expiration date will not be required to resubmit plans for renewal until the next registration cycle. If the manufacturer fails to register on time, due to fault of their own, those plans are no longer valid and will be required to be renewed. The asset for that structure is required to have been created and construction started before the expiration to be exempt from the renewal process for that specific plan and structure. 4.25 Tiny home plans must include: details on the vehicle chassis, including drawings and connections, and whether the tiny home is going to be installed on a permanent or temporary foundation. Inspections 4.26 All structures manufactured, sold, or offered for sale in the state of Colorado must display the Division of Housing insignia of approval affixed either by the Division of Housing, an authorized third party agency, or by a certified manufacturer. These insignias certify that the unit is constructed in compliance with applicable codes and regulations adopted by the State Housing Board pections 4.26 All structures manufactured, sold, or offered for sale in the state of Colorado must display the Division of Housing insignia of approval affixed either by the Division of Housing, an authorized third party agency, or by a certified manufacturer. These insignias certify that the unit is constructed in compliance with applicable codes and regulations adopted by the State Housing Board. This does not apply to factory-built structures or tiny homes manufactured or sold for transportation to and installation in another state. However, if the unit were to return to Colorado for use, then it would require an insignia issued by the Division of Housing. 4.26.1 Registered (non-certified) and certified manufacturers must apply for Colorado insignias through the Division of Housing and submit the appropriate fees provided in Rule 3 of these rules. 4.26.1.1 For units that are completed at the manufacturing facility (are not OC units), insignias will be affixed to each structure only upon final inspection approval by the Division of Housing or an authorized third party agency 4.26.1.2 For units that have on-site construction items, insignias will be affixed to each structure after an OC inspection by the Division of Housing or a third party agency or a local building department that has agreed to accept responsibility for the inspection of the OC items. 4.26.1.3 Insignias affixed by an authorized third party agency or a certified manufacturer must be reported to the Division of Housing, including the insignia number, type of insignia of approval affixed (residential or commercial), manufacturer, serial number, date of manufacture of the structure, and the first destination of the shipped structure. A manufacturer is required to provide a copy of its monthly production report. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing t be reported to the Division of Housing, including the insignia number, type of insignia of approval affixed (residential or commercial), manufacturer, serial number, date of manufacture of the structure, and the first destination of the shipped structure. A manufacturer is required to provide a copy of its monthly production report. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 46 4.26.1.3.1 The Division of Housing may elect to not issue additional insignias of approval to a third party agency or certified manufacturer if all insignias affixed are not timely and completely reported. 4.27.2 Insignias are assigned for use at a specific location and cannot be transferable or used on an unapproved structure. Colorado insignias of approval issued for one type of certification may not be used on a structure of another (different) type. A silver 3”x5” primary insignia (one or two family dwellings, except tiny homes) documenting manufacturer and design information is required for each structure to be installed in the state, or a blue 3”x5” primary insignia (commercial) documenting manufacturer and design information is required for each box to be installed in the state. A primary pink 3”x5” insignia will be required for each Tiny Home. A primary black 3x5 insignia will be attached to the primary box or Division of Housing approved location of each multi-family dwelling unit. A primary light green 3”x5” insignia will be adhered to the primary box of Emergency Response Units. 4.27.2.1 For residential only - each additional habitable floor section requires a silver 2”x2” “Additional Floor Tag” insignia7 4.27.2.2 For commercial only – an approved modification requires a green/silver 3”x5” “Modification” insignia. 4.27.2.3 For commercial only – components of a structure requires a purple 3”x5” “Component-only” insignia. 4.27.2.4 Both – factory-built structures inspected for another state requires a dark green 2”x2” “Inspection-only” insignia requires a silver 2”x2” “Additional Floor Tag” insignia7 4.27.2.2 For commercial only – an approved modification requires a green/silver 3”x5” “Modification” insignia. 4.27.2.3 For commercial only – components of a structure requires a purple 3”x5” “Component-only” insignia. 4.27.2.4 Both – factory-built structures inspected for another state requires a dark green 2”x2” “Inspection-only” insignia. 4.27.2.5 For Emergency Response Units – each additional box section requires a light green 2”x2” “Additional Floor Tag” insignia. 4.27.3 The primary insignia for residential and tiny homes must be permanently affixed inside the kitchen sink cabinet or inside the vanity cabinet if there is no kitchen sink. For certified manufacturers, this must occur prior to structures being removed from the production location that is certified. Additional Floor Tag insignias, if applicable, are to be permanently affixed and located directly under the primary insignia. 4.27.3.1 The primary insignia must contain the serial number, date of manufacture, wind design speed, roof design load, seismic zone, and construction codes. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 47 4.27.4 Colorado insignias are the property of the State of Colorado and may be confiscated by the Division of Housing upon any violation of these rules. Defaced, marked in error, or voided insignias must be returned to the Division of Housing without refund. 4.27.5 Dates on insignia are completion dates. 4.27.6 For installation and inspection insignias, the name of the installer or inspector is required. Not the company name. 4.28 Whenever an on-site inspection reveals that a structure fails to comply with any provision of these rules, the Division of Housing or the third party agency may affix a “Red Tag Notice” on the structure. All manufacturers must correct any construction code violations within thirty (30) calendar days of inspection. Life safety corrections may require less than 30 days to correct company name. 4.28 Whenever an on-site inspection reveals that a structure fails to comply with any provision of these rules, the Division of Housing or the third party agency may affix a “Red Tag Notice” on the structure. All manufacturers must correct any construction code violations within thirty (30) calendar days of inspection. Life safety corrections may require less than 30 days to correct. An extension may be granted when submitted in writing to the Division of Housing. 4.28.1 Once notified of a “Red Tag Notice” by the Division of Housing or the third party agency and the specific violation(s), the affected parties must resolve the issue(s) with the entity that posted the notice. 4.28.2 Within five (5) working days, the affected parties or their agents must notify, in writing, the Division of Housing or the third party agency of the action taken to correct the violation(s) and what steps have been taken by management to preclude the recurrence of the violation(s). Failure to respond within five (5) days may cause revocation of an affected party’s status. 4.28.3 A structure posted with a “Red Tag Notice” cannot be sold, offered for sale, or have occupancy in the state of Colorado, nor can it be moved or caused to be moved without the prior written approval of the Division of Housing or the third party agency. 4.28.4 All structures posted with a “Red Tag Notice” must be corrected or removed from the state (with prior written approval of the Division of Housing or the third party agency). All structures that are corrected will be re-inspected to assure compliance with the codes and regulations, and a re-inspection fee will be assessed. 4.28.4.1 Multiple violations may result in the Division of Housing suspending plan reviews submitted by the manufacturer until all issues are addressed. 4.28.5 A “Red Tag Notice” may be removed only by an authorized representative of the Division of Housing or the third party inspection agency. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing nd a re-inspection fee will be assessed. 4.28.4.1 Multiple violations may result in the Division of Housing suspending plan reviews submitted by the manufacturer until all issues are addressed. 4.28.5 A “Red Tag Notice” may be removed only by an authorized representative of the Division of Housing or the third party inspection agency. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 48 4.29 Factory-built structures may not be modified, prior to or during, installation at a site without approval from the Division of Housing. Once installed and its installation certified (factory-built residential structures only), any substantial alternation or repair made to the construction of the structure (both residential and nonresidential) already certified by the Division of Housing and on-site is under the jurisdiction of the local building department. 4.30 The Division of Housing and/or the third party agency retained by the manufacturer will conduct certification and production inspections of all manufacturers engaged in manufacturing or offering for sale factory-built structures in the state of Colorado. This inspection will include the quality control program and systems testing. This does not apply to factory-built structures manufactured or sold for transportation to and installation in another state. However, if the unit were to return to Colorado for use, then it would require an insignia issued by the Division of Housing. 4.30.1 Payment of the fees provided in Rule 3 is required if utilizing the services of an inspector from the Division of Housing. This cost is not refundable. 4.30.2 All in-state manufacturers shall have the option to contract with a third party agency or continue to use the Division of Housing to perform certifications and in-plant production inspections, to evaluate its registered/certified location’s Quality Control procedures, approve manufacturer engineering manuals and installation instructions and/or approve construction plans is not refundable. 4.30.2 All in-state manufacturers shall have the option to contract with a third party agency or continue to use the Division of Housing to perform certifications and in-plant production inspections, to evaluate its registered/certified location’s Quality Control procedures, approve manufacturer engineering manuals and installation instructions and/or approve construction plans. 4.30.3 Out of state manufacturers are required to obtain the services of a third party inspection agency to perform certifications and in-plant production inspections, to evaluate the plant’s Quality Control procedures, and may use an approved third party agency to approve manufacturer engineering manuals, installation instructions, and/or approve construction plans. 4.30.3.1 Another state where a registered/certified manufacturer is located may act as a third party agency for certifications, in-plant production inspections and evaluations of their Quality Control procedures provided it enters into a memorandum of understanding with the Division of Housing and the manufacturer follows all requirements for that entity. 4.31 A third party agency may consist of one of the following entities (any exceptions must have prior approval by the Division of Housing): (A) States – must enter into a memorandum of understanding with Colorado. (B) Local Government – must adopt Division-approved local ordinance or rule. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing r follows all requirements for that entity. 4.31 A third party agency may consist of one of the following entities (any exceptions must have prior approval by the Division of Housing): (A) States – must enter into a memorandum of understanding with Colorado. (B) Local Government – must adopt Division-approved local ordinance or rule. CODE OF COLORADO REGULATIONS 8 CCR 1302-14 Division of Housing 49 (C) Firms – must currently be listed with a national listing agency such as the International Code Council (ICC), International Accreditation Service (IAS), or other Division-approved entity [Text truncated at 120,000 characters. The full text is on the page linked above.] ## Nearby sections - [8 CCR 1302-1 FACTORY BUILT HOUSING CONSTRUCTION CODE AND MULTIPLE DWELLING CODE [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_1.md) - [8 CCR 1302-2 RESOLUTION NO..26 - RECREATIONAL AND PARK TRAILER VEHICLES [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_2.md) - [8 CCR 1302-3 RESOLUTION NO. 25 - FACTORY BUILT HOUSING [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_3.md) - [8 CCR 1302-4 RESOLUTION NO. 10 - MANUFACTURED HOME CONSTRUCTION STANDARDS AND PROCEDURAL REGULATIONS [Repealed and recodified as 8 CCR 1302-14 eff. 07/01/2018]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_4.md) - [8 CCR 1302-6 RESOLUTION NO. 24 - FACTORY BUILT NONRESIDENTIAL STRUCTURE [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_6.md) - [8 CCR 1302-7 RESOLUTION NO. 38 - MANUFACTURED HOUSING INSTALLATIONS [Repealed and recodified as 8 CCR 1302-14 eff. 07/01/2018]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_7.md) - [8 CCR 1302-10 RESOLUTION NO. 29 - ON-SITE CONSTRUCTION AND SAFETY CODES [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_10.md) - [8 CCR 1302-11 RESOLUTION NO. 35 - FACTORY BUILT NONRESIDENTIAL STRUCTURES [Repealed and recodified as 8 CCR 1302-14 eff. 07/01/2018]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_11.md) - [8 CCR 1302-12 RESOLUTION NO. 34 - FACTORY BUILT HOUSING [Repealed and recodified as 8 CCR 1302-14 eff. 07/01/2018]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_12.md) - [8 CCR 1302-13 RESOLUTION NO. 32 - RECREATIONAL AND PARK TRAILER VEHICLES [Repealed eff. 11/30/2003]](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_13.md) - [8 CCR 1302-14 NON-RESIDENTIAL AND RESIDENTIAL FACTORY-BUILT STRUCTURES AND TINY HOMES; SELLERS OF MANUFACTURED HOMES AND TINY HOMES; MANUFACTURED HOME, TINY HOME, AND MULTI-FAMILY STRUCTURE INSTALLATIONS](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_14.md) - [8 CCR 1302-15 MOBILE HOME PARK OVERSIGHT PROGRAM](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_15.md) - [8 CCR 1302-16 HOUSING INVESTMENT TRUST FUND INCOME LIMITS AND DEFINITION OF A SINGLE PERSON AS AN ELIGIBLE ENTITY FOR ASSISTANCE](https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_16.md) --- Source: Frix Law Library, https://www.frixlaw.com/law-library/statutes/STATE_CO_CCR_8_CCR_1302_14. Check the current official text before relying on it. Not legal advice.