# 60 FR 336: Airworthiness Directives; Lockheed Model L-1011-385 Series Airplanes

> Federal · Regulations · In force

URL: https://www.frixlaw.com/law-library/statutes/FR_RULE_95-52

## Section

- **Citation:** 60 FR 336
- **Heading:** Airworthiness Directives; Lockheed Model L-1011-385 Series Airplanes
- **Jurisdiction:** Federal
- **Kind:** Regulations
- **Status:** In force
- **Text as of:** September 30, 2026
- **Source:** Compiled text
- **Location:** Federal Register / Vol. 60 / 60 FR 336

## Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 94-NM-17-AD; Amendment 39-9104; AD 94-26-09]

Airworthiness Directives; Lockheed Model L-1011-385 Series
Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to certain Lockheed Model L-1011-385 series airplanes, that
requires an initial servicing or overhaul of the ram air turbine (RAT),
and incorporating repetitive overhaul actions into the FAA-approved
maintenance program. This amendment is prompted by reports indicating
that, during routine maintenance of the RAT, the turbine blade assembly
separated during spin tests. The actions specified by this AD are
intended to prevent separation of the turbine blade assembly, which
could damage the airplane structure and systems, and, under certain
circumstances, could lead to reduced controllability of the airplane.

DATES: Effective February 3, 1995.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of February 3, 1995.

ADDRESSES: The service information referenced in this AD may be
obtained from Lockheed Aeronautical Systems Support Company, Field
Support Department, Dept. 693, Zone 0755, 2251 Lake Park Drive, Smyrna,
Georgia 30080. This information may be examined at the Federal Aviation
Administration (FAA), Transport Airplane Directorate, Rules Docket,
1601 Lind Avenue, SW., Renton, Washington; or at the FAA, Small
Airplane Directorate, Atlanta Aircraft Certification Office, Campus
Building, 1701 Columbia Avenue, Suite 2-160, College Park, Georgia; or
at the Office of the Federal Register, 800 North Capitol Street, NW.,
suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: Thomas Peters, Aerospace Engineer,
Flight Test Branch, ACE-160A, FAA, Small Airplane Directorate, Atlanta
Aircraft Certification Office, Campus Building, 1701 Columbia Avenue,
Suite 2-160, College Park, Georgia 30337-2748; telephone (404) 305-
7367; fax (404) 305-7348.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to certain Lockheed Model L-1011-385
series airplanes was published in the Federal Register on April 25,
1994 (59 FR 19683). That action proposed to require an initial
servicing or overhaul of the ram air turbine (RAT), and incorporating
repetitive overhaul actions into the FAA-approved maintenance program.
Interested persons have been afforded an opportunity to participate
in the making of this amendment. Due consideration has been given to
the comments received.
One commenter supports the proposal.
The Air Transport Association (ATA) of America, on behalf of some
of its member operators, suggests that the proposal be withdrawn
because it is ``an inappropriate use of the airworthiness directive.''
This commenter states that AD's are not the proper vehicle for
addressing maintenance problems. The commenter points out that the AD
is based on failures that have been reported, not during service, but
during routine maintenance of the RAT. Further, the commenter states
that the FAA's analysis identifies the problem area as the turbine
blade assembly, and the maintenance deficiency as lack of lubrication;
yet the FAA's proposed corrective action is a complete overhaul of the
unit. The commenter questions whether the FAA considered a ``simpler
remedy,'' such as a periodic lubrication requirement or increased
frequency of functional checks. The commenter requests that the FAA
examine vehicles other than the AD to ensure that appropriate
maintenance is performed.
The FAA does not concur with the commenter's request to withdraw
the AD, nor does it concur with the commenter's implication that the AD
is not the proper vehicle for addressing the unsafe condition.
According to section 39.1 of the Federal Aviation Regulations (FAR) (14
CFR 39.1), the issuance of an AD is based on the finding that an unsafe
condition is likely to exist or develop in aircraft of a particular
type design. The responsibilities placed on the FAA by the Federal
Aviation Act do not limit it from making any unsafe condition--whether
resulting from maintenance, design defect, or otherwise--the proper
subject of an AD. Therefore, regardless of the cause or the source of
an unsafe condition, the FAA has the authority to issue an AD when it
is found that an unsafe condition is likely to exist or develop on
other products of the same type design.
Further, it is within the FAA's authority to issue AD's to require
actions to address unsafe conditions that are not otherwise being
addressed (or addressed adequately) by normal maintenance procedures.
The FAA may address such unsafe conditions by requiring revisions to
maintenance programs as a condition under which airplanes may continue
to be operated. While the subject of this AD relates to a problem with
the RAT assembly that was identified during regular maintenance
procedures, the FAA points out that reports of this problem came from
several different operators. From the data garnered from these reports,
the FAA has identified the existence of an unsafe condition. Although
the unsafe condition is one that, feasibly, could have been addressed
by the operators' maintenance programs, it is obvious that the current
maintenance programs are inadequate in addressing it. In light of this,
the unsafe condition is likely to exist or develop in the affected
airplanes. As a result, the FAA is issuing this AD to eliminate the
unsafe condition by revising the maintenance programs accordingly. The
AD is the appropriate vehicle for mandating such actions.
The FAA acknowledges that some operators currently may have better
maintenance programs that address an unsafe condition. If a program is
adequate, an operator would already be in compliance with the AD, or
would be in a position to obtain an approval for an alternative method
of compliance with the AD (i.e., to follow the operator's current
program rather than revise it to comply with the AD). The obligation of
the FAA to issue the AD and address an unsafe condition remains,
however, and the rule must apply to everyone to ensure that all
affected airplanes are covered, regardless of who operates them.
In developing this AD action, the FAA did consider optional actions
to address strictly the bearing lubrication problem. However, in
reviewing the available data, the FAA found that there were no
mandatory replacement or refurbishment times for the RAT in the
majority of affected operators' maintenance programs. Under normal
maintenance procedures, the RAT's are functionally tested on the an
average of every 48 months or 4,000 flights (at a ``D'' check). In
cases where operators had replaced or refurbished the RAT's, those
actions were accomplished ``on condition'' only, that is, after the
RAT's had failed certain functional (spin-up) testing. In the reported
incidents, the RAT's had not been serviced, nor had functional testing
indicated that they needed servicing, since new. It is likely that
RAT's have been installed on many other affected airplanes, and have
had no servicing whatsoever since delivery that would
ensure adequate lubrication of the turbine bearing. In light of this,
the FAA has clearly identified an unsafe condition that must be
addressed by the actions specified by this AD to be incorporated in the
operators' maintenance programs.
Further, the FAA points out that the normal means for air carriers
to comply with AD's such as this is to incorporate the repetitive
requirements into their approved maintenance program. Therefore, the
FAA could accomplish this same result by enumerating the specific
overhaul/servicing actions identified by the maintenance program
revision. However, from an administrative point of view, there is a
distinct advantage in requiring a maintenance program revision. By
imposing the overhaul/servicing requirements, compliance with the AD
with respect to each action would have to be recorded in the operator's
maintenance records; whereas, in the case of this AD, the only required
recording of the compliance relates to the one-time changes in the
maintenance program required by paragraph (b) of the rule.
One commenter requests that the proposal be revised to require only
a one-time inspection and servicing of the RAT. Data gathered from the
results of the inspection could then be evaluated to determine the
condition of the fleet and if additional actions are warranted. This
commenter believes that the reported bearing failures were isolated
incidents, and that issuance of the proposed AD is an ``overreaction''
to these reports. The FAA does not concur. From data already obtained,
the FAA has determined that a sufficient number of failures have
occurred which clearly indicate that the RAT installed in the Model L-
1011-385 is likely to develop problems in the turbine bearing unless
measures are implemented to periodically lubricate the bearing.
Issuance of this AD is the result of that determination.
One commenter supports the intent of the proposed rule, but
requests that proposed paragraph (b) be revised to delete the
requirement for a complete overhaul of the RAT every eight years. The
commenter considers this to be excessive. The commenter states that the
turbine separation problems, like those that have occurred, should be
correctable by periodically performing only the servicing procedures in
accordance with Lockheed TriStar L-1011 Service Bulletin 093-29-098,
dated December 6, 1993 (reference Dowty Service Bulletin RAT16C10-29-
168). The FAA concurs that the servicing procedures are acceptable in
ensuring that the addressed problems associated with the turbine blade
assembly are monitored and corrected in a timely manner. Accordingly,
the FAA has revised paragraph (b) to provide operators with the option
of accomplishing either the complete overhaul of the RAT or the
servicing procedures, at eight-year intervals.
Another commenter requests that the proposal be revised to allow
RAT's that have been overhauled previously in accordance with Dowty
Overhaul Manual 29-21-01 to be considered in compliance with the AD,
even though the overhaul manual does not call for the replacement of
the roller bearing, part number RA56341. The commenter states that the
lubrication problem addressed by the proposed AD occurs mainly in the
turbine ball bearing (part number 601017118), not the roller bearing.
The Dowty Overhaul Manual does not call for replacement of the roller
bearing if it is still serviceable; however, Lockheed TriStar L-1011
Service Bulletin 093-29-098, dated December 6, 1993, which was cited in
the proposed rule, calls for the replacement of the roller bearing,
regardless of its condition. The FAA does not concur with the
commenter's request. The replacement of the roller bearing, as called
for in the referenced service bulletin, is necessary because of
corrosion damage problems that can occur in the roller bearing. This
corrosion damage may be difficult to detect by visual inspection alone;
thus, initial replacement of the bearing (during overhaul) is all the
more important. However, this corrosion problem will be monitored and
corrected, if necessary, during the regular repetitive servicing or
overhaul (every eight years) required by this AD. In light of this,
inspection and reinstallation of both the roller and ball bearings, if
serviceable, would be acceptable at the recurrent actions required by
the AD. A note has been added to the final rule to clarify that
replacement of the roller bearing is necessary when initially
overhauling the RAT.
The FAA has recently reviewed the figures it has used over the past
several years in calculating the economic impact of AD activity. In
order to account for various inflationary costs in the airline
industry, the FAA has determined that it is necessary to increase the
labor rate used in these calculations from $55 per work hour to $60 per
work hour. The cost estimate information, below has been revised to
reflect this increase in the specified hourly labor rate.
After careful review of the available data, including the comments
noted above, the FAA has determined that air safety and the public
interest require the adoption of the rule with the changes previously
described. The FAA has determined that these changes will neither
increase the economic burden on any operator nor increase the scope of
the AD.

Cost Estimate

There are approximately 236 Lockheed Model L-1011-385 series
airplanes of the affected design in the worldwide fleet. The FAA
estimates that 117 airplanes of U.S. registry will be affected by this
AD.
For operators electing to service the RAT, it will take
approximately 48 work hours per RAT to accomplish those actions, at an
average labor rate of $60 per work hour. Based on these figures, the
total cost impact of the servicing actions on U.S. operators is
estimated to be $2,880 per RAT.
For operators electing to overhaul the RAT, it will take
approximately 170 work hours per RAT to accomplish those actions, at an
average labor rate of $60 per work hour. Based on these figures, the
total cost impact of the overhaul actions on U.S. operators is
estimated to be $10,200 per RAT.
The number of work hours that will be required to perform either
the servicing or overhaul of the RAT, as indicated above, is presented
as if those actions were to be accomplished as ``stand alone'' actions.
However, in actual practice, these actions for the most part could be
accomplished coincidentally or in combination with normally scheduled
airplane inspections and other maintenance program tasks. Therefore,
the actual number of any necessary additional work hours will be
minimal in many instances. Additionally, any costs associated with
special airplane scheduling will be minimal.
Incorporation of the requirements of this AD into the FAA-approved
maintenance program will require approximately 40 work hours per
operator to accomplish, at an average labor rate of $60 per work hour.
Based on these figures, the total cost impact of incorporation of the
maintenance program change on U.S. operators is estimated to be $2,400
per operator.
The FAA recognizes that the obligation to maintain aircraft in an
airworthy condition is vital, but sometimes expensive. Because AD's
require specific actions to address specific unsafe conditions, they
appear to impose costs that would not otherwise be borne by operators.
However, because of the general obligation of operators to
maintain aircraft in an airworthy condition, this appearance is
deceptive. Attributing those costs solely to the issuance of this AD is
unrealistic because, in the interest of maintaining safe aircraft, most
prudent operators would accomplish the required actions even if they
were not required to do so by the AD.
A full cost-benefit analysis has not been accomplished for this AD.
As a matter of law, in order to be airworthy, an aircraft must conform
to its type design and be in a condition for safe operation. The type
design is approved only after the FAA makes a determination that it
complies with all applicable airworthiness requirements. In adopting
and maintaining those requirements, the FAA has already made the
determination that they establish a level of safety that is cost-
beneficial. When the FAA, as in this AD, makes a finding of an unsafe
condition, this means that the original cost-beneficial level of safety
is no longer being achieved and that the required actions are necessary
to restore that level of safety. Because this level of safety has
already been determined to be cost-beneficial, a full cost-benefit
analysis for this AD would be redundant and unnecessary.

Regulatory Impact

The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. App. 1354(a), 1421 and 1423; 49 U.S.C.
106(g); and 14 CFR 11.89.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new
airworthiness directive:

94-26-09 Lockhead: Amendment 39-9104. Docket 94-NM-17-AD.

Applicability: Model L-1011-385 series airplanes having serial
numbers 193A through 193Y inclusive, 293A through 293F inclusive,
and 1002 through 1250 inclusive; certificated in any category.
Compliance: Required as indicated, unless accomplished
previously.
To prevent separation of the turbine blade assembly, which could
damage the airplane structure and systems, and, under certain
circumstances, lead to reduced controllability of the airplane,
accomplish the following:
(a) Remove, disassemble, inspect, test, and service the ram air
turbine (RAT) in accordance with Lockheed TriStar L-1011 Service
Bulletin 093-29-098, dated December 6, 1993; or completely overhaul
the RAT in accordance with Chapter 29-21-01 of Dowty Aerospace
Hydraulics--Cheltenham Overhaul Manual; at the applicable time
specified in either paragraph (a)(1) or (a)(2) of this AD:

Note 1: Overhaul of the RAT in accordance with this paragraph
includes replacement of the roller bearing (part number RA56341).

(1) For airplanes on which the RAT has not been serviced or
overhauled within 6 years prior to the effective date of this AD:
Accomplish the procedures within 2 years after the effective date of
this AD.
(2) For airplanes on which the RAT has been serviced or
overhauled within 6 years prior to the effective date of this AD in
accordance with a method that is equivalent to the procedures
described in Dowty Aerospace Hydraulics--Cheltenham Service Bulletin
RAT16C10-29-168, dated December 1, 1993: Accomplish the procedures
within 8 years after the date of the immediately preceding servicing
of the RAT.
(b) Within 24 months after the effective date of this AD, revise
the FAA-approved maintenance program to incorporate procedures for
servicing of the RAT in accordance with Lockheed TriStar L-1011
Service Bulletin 093-29-098, dated December 6, 1993; or complete
overhaul of the RAT in accordance with Chapter 29-21-01 of Dowty
Aerospace Hydraulics--Cheltenham Overhaul Manual. One or the other
of these actions must be accomplished at intervals not to exceed 8
years.
(c) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, Atlanta Aircraft Certification
Office (ACO), FAA, Small Airplane Directorate. Operators shall
submit their requests through an appropriate FAA Principal
Maintenance Inspector, who may add comments and then send it to the
Manager, Atlanta ACO.

Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Atlanta ACO.

(d) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
(e) The servicing actions shall be done in accordance with
Lockheed TriStar L-1011 Service Bulletin 093-29-098, dated December
6, 1993. This incorporation by reference was approved by the
Director of the Federal Register in accordance with 5 U.S.C. 552(a)
and 1 CFR part 51. Copies may be obtained from Lockheed Aeronautical
Systems Support Company, Field Support Department, Dept. 693, Zone
0755, 2251 Lake Park Drive, Smyrna, Georgia 30080. Copies may be
inspected at the FAA, Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the FAA, Atlanta Aircraft
Certification Office, Small Airplane Directorate, Campus Building,
1701 Columbia Avenue, Suite 2-160, College Park, Georgia; or at the
Office of the Federal Register, 800 North Capitol Street, NW., suite
700, Washington, DC.
(f) This amendment becomes effective on February 3, 1995.

Issued in Renton, Washington, on December 19, 1994.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 95-52 Filed 1-3-95; 8:45 am]
BILLING CODE 4910-13-U

## Nearby sections

- [60 FR 328 [No title available]](https://www.frixlaw.com/law-library/statutes/FR_RULE_X95-10104.md)
- [60 FR 329 Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-49.md)
- [60 FR 332 Airworthiness Directives; Fokker Model F27 Series Airplanes (Excluding Mark 050 Series Airplanes)](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-51.md)
- [60 FR 336 Airworthiness Directives; Lockheed Model L-1011-385 Series Airplanes](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-52.md)
- [60 FR 362 Oral Dosage Form New Animal Drugs; Lufenuron Tablets](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-164.md)
- [60 FR 375 Approval and Promulgation of Implementation Plan; State of Indiana](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-148.md)
- [60 FR 377 [No title available]](https://www.frixlaw.com/law-library/statutes/FR_RULE_X95-30104.md)
- [60 FR 1747 Defense Federal Acquisition Regulation Supplement; Restructuring Costs](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-158.md)
- [60 FR 2321 Pine Shoot Beetle](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-424.md)
- [60 FR 2497 Traffic Alert and Collision Avoidance System, TCAS I](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-571.md)
- [60 FR 2512 Oklahoma Regulatory Program](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-568.md)
- [60 FR 2520 Utah Regulatory Program](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-569.md)
- [60 FR 2524 Approval and Promulgation of Air Quality Implementation Plans; Connecticut, Maine, Rhode Island, and Vermont; Emission Statements](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-567.md)
- [60 FR 2527 Clean Air Act Interim Approval of Operating Permits Program; City of Albuquerque Environmental Health Department, Air Pollution Control Division](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-547.md)

---

Source: Frix Law Library, https://www.frixlaw.com/law-library/statutes/FR_RULE_95-52. Check the current official text before relying on it. Not legal advice.
