# 60 FR 329: Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes

> Federal · Regulations · In force

URL: https://www.frixlaw.com/law-library/statutes/FR_RULE_95-49

## Section

- **Citation:** 60 FR 329
- **Heading:** Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes
- **Jurisdiction:** Federal
- **Kind:** Regulations
- **Status:** In force
- **Text as of:** September 30, 2026
- **Source:** Compiled text
- **Location:** Federal Register / Vol. 60 / 60 FR 329

## Text

DEPARTMENT OF TRANSPORTATION

14 CFR Part 39

[Docket No. 94-NM-108-AD; Amendment 39-9109; AD 94-26-14]

Airworthiness Directives; British Aerospace Model Viscount 744,
745D, and 810 Series Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Final rule.

-----------------------------------------------------------------------

SUMMARY: This amendment adopts a new airworthiness directive (AD),
applicable to all British Aerospace Model Viscount 744, 745D, and 810
series airplanes, that requires inspections to detect cracks in the
chassis side bracing structure and in the chassis top strut support
intercostals inside the wings, and replacement of discrepant parts with
new parts. This proposal would also require inspection of the
intercostals to determine the specification of the material, if
necessary, and replacement of discrepant parts with new parts. This
amendment is prompted by a report of cracking in the chassis top strut
support intercostal in the side bracing structure inside the wing due
to the effects of metal fatigue. The actions specified by this AD are
intended to prevent such fatigue-related cracking, which could lead to
the failure of the chassis side bracing structure inside the wings and
consequent reduced structural integrity of the chassis support
structure.

DATES: Effective on February 3, 1995.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of February 3, 1995.

ADDRESSES: The service information referenced in this AD may be
obtained from British Aerospace Regional Aircraft Ltd., Engineering
Support Manager, Military Business Unit, Chadderton Works, Greengate,
Middleton, Manchester M24 1SA, England. This information may be
examined at the Federal Aviation Administration (FAA), Transport
Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton,
Washington; or at the Office of the Federal Register, 800 North Capitol
Street, NW., suite 700, Washington, DC.

FOR FURTHER INFORMATION CONTACT: William Schroeder, Aerospace Engineer,
Standardization Branch, ANM-113, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (206)
227-2148; fax (206) 227-1320.

SUPPLEMENTARY INFORMATION: A proposal to amend part 39 of the Federal
Aviation Regulations (14 CFR part 39) to include an airworthiness
directive (AD) that is applicable to all British Aerospace Model
Viscount 744, 745D, and 810 series airplanes was published in the
Federal Register on September 9, 1994 (59 FR 46596). That action
proposed to require repetitive detailed visual inspections to detect
cracks in the chassis side bracing structure and in the chassis top
strut support intercostals of the inner wings, and replacement of
discrepant parts with new parts. That action also proposed to require
an eddy current inspection to determine the specification of the
material of the intercostals, if necessary, and replacement of
discrepant parts with new parts.
Interested persons have been afforded an opportunity to participate
in the making of this amendment. Due consideration has been given to
the single comment received.
The commenter supports the proposed rule.
As a result of recent communications with the Air Transport
Association (ATA) of America, the FAA has learned that, in general,
some operators may misunderstand the legal effect of AD's on airplanes
that are identified in the applicability provision of the AD, but that
have been altered or repaired in the area addressed by the AD. The FAA
points out that all airplanes identified in the applicability provision
of an AD are legally subject to the AD. If an airplane has been altered
or repaired in the affected area in such a way as to affect compliance
with the AD, the owner or operator is required to obtain FAA approval
for an alternative method of compliance with the AD, in accordance with
the paragraph of each AD that provides for such approvals. A note has
been added to this final rule to clarify this requirement.
The FAA has recently reviewed the figures it has used over the past
several years in calculating the economic impact of AD activity. In
order to account for various inflationary costs in the airline
industry, the FAA has determined that it is necessary to increase the
labor rate used in these calculations from $55 per work hour to $60 per
work hour. The economic impact information, below, has been revised to
reflect this increase in the specified hourly labor rate.
After careful review of the available data, including the comment
noted above, the FAA has determined that air safety and the public
interest require the adoption of the rule with the changes previously
described. The FAA has determined that these changes will neither
increase the economic burden on any operator nor increase the scope of
the AD.
The FAA estimates that 25 Model Viscount 744 and 745D series
airplanes of U.S. registry will be affected by this AD, that it will
take approximately 15 work hours per airplane to accomplish the
required actions, and that the average labor rate is $60 per work hour.
Based on these figures, the total cost impact of the AD on U.S.
operators is estimated to be $22,500, or $900 per airplane, per
inspection cycle.
The FAA estimates that 4 Model Viscount 810 series airplanes of
U.S. registry will be affected by this AD, that it will take
approximately 15 work hours per airplane to accomplish the required
actions, and that the average labor rate is $60 per work hour. Based on
these figures, the total cost impact of the proposed AD on U.S.
operators is estimated to be $3,600, or $900 per airplane, per
inspection cycle.
Based on the above figures, the total cost impact of the actions
proposed by this AD on U.S. operators is estimated to be $26,100, or
$900 per airplane, per inspection cycle.
The total cost impact figure discussed above is based on
assumptions that no operator has yet accomplished any of the
requirements of this AD action, and that no operator would accomplish
those actions in the future if this AD were not adopted.
The regulations adopted herein will not have substantial direct
effects on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, in
accordance with Executive Order 12612, it is determined that this final
rule does not have sufficient federalism implications to warrant the
preparation of a Federalism Assessment.
For the reasons discussed above, I certify that this action (1) is
not a ``significant regulatory action'' under Executive Order 12866;
(2) is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and (3) will not have a
significant economic impact, positive or negative, on a substantial
number of small entities under the criteria of the Regulatory
Flexibility Act. A final evaluation has been prepared for this action
and it is contained in the Rules Docket. A copy of it may be obtained
from the Rules Docket at the location provided under the caption
ADDRESSES.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.

Adoption of the Amendment

Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. App. 1354(a), 1421 and 1423; 49 U.S.C.
106(g); and 14 CFR 11.89.

Sec. 39.13 [Amended]

2. Section 39.13 is amended by adding the following new
airworthiness directive:

94-26-14 British Aerospace Regional Aircraft Limited (Formerly
British Aerospace Commercial Aircraft Limited, Vickers-Armstrongs
Aircraft Limited): Amendment 39-9109. Docket 94-NM-108-AD.

Applicability: All Model Viscount 744, 745D, and 810 series
airplanes, certificated in any category.

Note 1: This AD applies to each airplane identified in the
preceding applicability provision, regardless of whether it has been
modified, altered, or repaired in the area subject to the
requirements of this AD. For airplanes that have been modified,
altered, or repaired so that the performance of the requirements of
this AD is affected, the owner/operator must use the authority
provided in paragraph (b) to request approval from the FAA. This
approval may address either no action, if the current configuration
eliminates the unsafe condition; or different actions necessary to
address the unsafe condition described in this AD. Such a request
should include an assessment of the effect of the changed
configuration on the unsafe condition addressed by this AD. In no
case does the presence of any modification, alteration, or repair
remove any airplane from the applicability of this AD.

Compliance: Required as indicated, unless accomplished
previously.
To prevent reduced structural integrity of the chassis,
accomplish the following:
(a) Within 6 months after the effective date of this AD, perform
a detailed visual inspection to detect cracks in the chassis side
bracing structure and in the chassis top strut support intercostals
inside the wings between stations 81 and 96, in accordance with
British Aerospace Viscount Preliminary Technical Leaflet (PTL) 332,
Issue 1, Disc 11 Doc.4, dated December 2, 1991 (for Model Viscount
744 and 745D series airplanes); or British Aerospace Viscount PTL
203, Issue 1, Disc 11 Doc.2, dated December 2, 1991 (for Model
Viscount 810 series airplanes); as applicable.
(1) If no cracking is detected in the chassis side bracing
structure, repeat the inspection thereafter at intervals not to
exceed 1,500 flight hours or 14 months, whichever occurs first.
(2) If any cracking is detected in the chassis side bracing
structure, prior to further flight, replace the cracked side of the
bracing structure with a new structure, in accordance with the
applicable PTL.
(3) If no cracking is detected in the chassis top strut support
intercostal, prior to further flight, perform an eddy current
inspection to determine the specification of the material (either
L72 or L73) of the intercostals, in accordance with the applicable
PTL.
(i) If the material is manufactured from L72, prior to further
flight, replace the chassis top strut support intercostal with a new
chassis top strut support intercostal, in accordance with the
applicable PTL.
(ii) If the material is manufactured from L73, no further action
is required by paragraph (a)(3) of this AD.
(4) If cracking is detected in the chassis top strut support
intercostal, prior to further flight, replace it with a new chassis
top strut support intercostal, in accordance with the applicable
PTL.
(b) An alternative method of compliance or adjustment of the
compliance time that provides an acceptable level of safety may be
used if approved by the Manager, Standardization Branch, ANM-113,
FAA, Transport Airplane Directorate. Operators shall submit their
requests through an appropriate FAA Principal Maintenance Inspector,
who may add comments and then send it to the Manager,
Standardization Branch, ANM-113.

Note 2: Information concerning the existence of approved
alternative methods of compliance with this AD, if any, may be
obtained from the Standardization Branch, ANM-113.

(c) Special flight permits may be issued in accordance with
sections 21.197 and 21.199 of the Federal Aviation Regulations (14
CFR 21.197 and 21.199) to operate the airplane to a location where
the requirements of this AD can be accomplished.
(d) The inspections and replacements shall be done in accordance
with British Aerospace Viscount Preliminary Technical Leaflet (PTL)
332, Issue 1, Disc 11 Doc.4, dated December 2, 1991 (for Model
Viscount 744 and 745D series airplanes); or British Aerospace
Viscount PTL 203, Issue 1, Disc 11 Doc.2, dated December 2, 1991
(for Model Viscount 810 series airplanes); as applicable. This
incorporation by reference was approved by the Director of the
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part
51. Copies may be obtained from British Aerospace Regional Aircraft
Ltd., Engineering Support Manager, Military Business Unit,
Chadderton Works, Greengate, Middleton, Manchester M24 1SA, England.
Copies may be inspected at the FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington; or at the Office of the
Federal Register, 800 North Capitol Street, NW., suite 700,
Washington, DC.
(e) This amendment becomes effective on February 3, 1995.

Issued in Renton, Washington, on December 21, 1994.
Darrell M. Pederson,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 95-49 Filed 1-3-95; 8:45 am]
BILLING CODE 4910-13-U

## Nearby sections

- [60 FR 328 [No title available]](https://www.frixlaw.com/law-library/statutes/FR_RULE_X95-10104.md)
- [60 FR 329 Airworthiness Directives; British Aerospace Model Viscount 744, 745D, and 810 Series Airplanes](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-49.md)
- [60 FR 332 Airworthiness Directives; Fokker Model F27 Series Airplanes (Excluding Mark 050 Series Airplanes)](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-51.md)
- [60 FR 336 Airworthiness Directives; Lockheed Model L-1011-385 Series Airplanes](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-52.md)
- [60 FR 362 Oral Dosage Form New Animal Drugs; Lufenuron Tablets](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-164.md)
- [60 FR 375 Approval and Promulgation of Implementation Plan; State of Indiana](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-148.md)
- [60 FR 377 [No title available]](https://www.frixlaw.com/law-library/statutes/FR_RULE_X95-30104.md)
- [60 FR 1747 Defense Federal Acquisition Regulation Supplement; Restructuring Costs](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-158.md)
- [60 FR 2321 Pine Shoot Beetle](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-424.md)
- [60 FR 2497 Traffic Alert and Collision Avoidance System, TCAS I](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-571.md)
- [60 FR 2512 Oklahoma Regulatory Program](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-568.md)
- [60 FR 2520 Utah Regulatory Program](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-569.md)
- [60 FR 2524 Approval and Promulgation of Air Quality Implementation Plans; Connecticut, Maine, Rhode Island, and Vermont; Emission Statements](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-567.md)
- [60 FR 2527 Clean Air Act Interim Approval of Operating Permits Program; City of Albuquerque Environmental Health Department, Air Pollution Control Division](https://www.frixlaw.com/law-library/statutes/FR_RULE_95-547.md)

---

Source: Frix Law Library, https://www.frixlaw.com/law-library/statutes/FR_RULE_95-49. Check the current official text before relying on it. Not legal advice.
