# Update to Electrical Engineering Regulations

> Briefs, arguments, decisions, and more.

URL: https://www.frixlaw.com/law-library/documents/fr%3A2021-06699

## Record

- **Collection:** Federal Register
- **Document type:** Proposed Rule
- **Published:** April 22, 2021
- **Citation:** 86 FR 21440

## Text

DEPARTMENT OF HOMELAND SECURITY
Coast Guard
46 CFR Parts 110, 111, 112, and 113
[Docket No. USCG-2020-0075]
RIN 1625-AC66
Update to Electrical Engineering Regulations

AGENCY:

Coast Guard, DHS.

ACTION:

Notice of proposed rulemaking.

SUMMARY:

The Coast Guard proposes to update electrical engineering standards that are incorporated by reference and add acceptable alternative standards. This proposed rule would also eliminate several outdated or unnecessarily prescriptive electrical engineering regulations. This proposed regulatory action would be consistent with the standards currently used by industry and support the Coast Guard's maritime safety mission.

DATES:

Comments and related material must be received by the Coast Guard on or before July 21, 2021.

ADDRESSES:

You may submit comments identified by docket number USCG-2020-0075 using the Federal eRulemaking Portal at
https://www.regulations.gov.
See the “Public Participation and Request for Comments” portion of the
SUPPLEMENTARY INFORMATION
section for further instructions on submitting comments.

Viewing material proposed for incorporation by reference.
Material incorporated by reference is available from the publishers identified in the proposed text of 46 CFR 110.10-1, including in this document. Alternatively, you may make arrangements to view this material by calling the person identified in the
FOR FURTHER INFORMATION CONTACT
section of this document.

FOR FURTHER INFORMATION CONTACT:

For information about this document call or email Raymond Martin, Systems Engineering Division, Coast Guard; telephone 202-372-1384, email
Raymond.W.Martin@uscg.mil.

SUPPLEMENTARY INFORMATION:

Table of Contents for Preamble

I. Public Participation and Request for Comments

II. Abbreviations

III. Executive Summary

IV. Basis and Purpose

V. Background

VI. Discussion of Proposed Rule

A. Proposed Revisions to § 110.10-1 Incorporation by Reference

B. Generator Prime Movers

C. Electrical Cable

D. IEC 60092-502 Electrical Installations in Ships—Part 502: Tankers—Special Features

E. Emergency Generator in Port

F. Description of Additional Proposed Changes Within Subchapter J

VII. Incorporation by Reference

VIII. Regulatory Analyses

A. Regulatory Planning and Review

B. Small Entities

C. Assistance for Small Entities

D. Collection of Information

E. Federalism

F. Unfunded Mandates Reform Act

G. Taking of Private Property

H. Civil Justice Reform

I. Protection of Children

J. Indian Tribal Governments

K. Energy Effects

L. Technical Standards

M. Environment

I. Public Participation and Request for Comments

The Coast Guard views public participation as essential to effective rulemaking, and will consider all comments and material received during the comment period. Your comment can help shape the outcome of this proposed rulemaking. If you submit a comment, please include the docket number for this proposed rulemaking, indicate the specific section of this document to which each comment applies, and provide a reason for each suggestion or recommendation. Where possible, please provide any available data to support the reason for each suggestion or recommendation.

We encourage you to submit comments through the Federal eRulemaking Portal at
https://www.regulations.gov.
If your material cannot be submitted using
https://www.regulations.gov,
contact the person in the
FOR FURTHER INFORMATION CONTACT
section of this proposed rule for alternate instructions. Documents mentioned in this proposed rule, and all public comments, will be available in our online docket at
https://www.regulations.gov,
and can be viewed by following that website's instructions. Additionally, if you go to the online docket and sign up for email alerts, you will be notified when comments are posted or if a final rule is published.

We accept anonymous comments. All comments received will be posted without change to
https://www.regulations.gov
and will include any personal information you have provided. For more about privacy and submissions in response to this document, see DHS's eRulemaking System of Records notice (85 FR 14226, March 11, 2020).

We do not plan to hold a public meeting, but will consider doing so if our evaluation of public comments indicates that a meeting would be helpful. We would issue a separate
Federal Register
notice to announce the date, time, and location of such a meeting.

II. Abbreviations

ABS American Bureau of Shipping

AC Alternating current

ANSI American National Standards Institute

API American Petroleum Institute

ASME American Society of Mechanical Engineers

ASTM ASTM International

BLS Bureau of Labor Statistics

CAN Canadian National Standard

CFR Code of Federal Regulations

CSA Canadian Standards Association

DC Direct current

DHS Department of Homeland Security

EMC Electromagnetic compatibility

Ex Designation of explosion-protected electrical apparatus complying with IEC standards

FR Federal Register

HVSC High voltage shore connection

IBR Incorporated by Reference

IEC International Electrotechnical Commission

IECEx System IEC System for Certification to Standards relating to Equipment for use in Explosive Atmospheres

IEEE Institute of Electrical and Electronics Engineers

IMO International Maritime Organization

ISA International Society of Automation

ISO International Organization of Standardization

kV Kilovolt

kW Kilowatt

LED Light-emitting diode

MSC Marine Safety Center

MODU Mobile Offshore Drilling Unit

MOU Marine Offshore Unit

NAVSEA Naval Sea Systems Command

NEMA National Electrical Manufacturers Association

NFPA National Fire Protection Association

NPRM Notice of Proposed Rulemaking

NVIC Navigation and Vessel Inspection Circular

OCS Outer Continental Shelf

OMB Office of Management and Budget

OSV Offshore Supply Vessel

§ Section

SOLAS International Convention for Safety of Life at Sea, 1974

U.S.C. United States Code

V Volts

III. Executive Summary

When writing regulations that set technical standards, the Coast Guard relies as much as possible on existing industry consensus standards. Doing so minimizes proliferation of differing standards and complies with the National Technology Transfer and Advancement Act and OMB Circular A-119. The legal method of directing

regulated entities to follow separately published standards is called incorporation by reference (IBR). This notice of proposed rulemaking (NPRM) proposes to update prior incorporations by reference, add a limited number of alternative standards, and eliminate outdated or unnecessarily prescriptive regulations in title 46 of the Code of Federal Regulations (CFR) subchapter J.

This proposed rule would update the standards incorporated by reference (IBR) in both 46 CFR 110.10-1 and all of the sections in subchapter J that reference the updated IBR standards. More specifically, this proposed rule would incorporate the more recent editions of many standards, incorporate by reference additional standards for certain topics, and remove IBR standards that are no longer actively used by industry. Due to technological advances, it is necessary to update the current standards to ensure modern technologies are addressed in the regulations. In addition to updating the IBR standards, we propose the following four changes to subchapter J.

First, this proposed rule would eliminate the prescriptive requirements in 46 CFR 111.12-1(b) and (c) for generator prime movers. In accordance with 46 CFR 58.01-5, these generator prime movers would continue to be required to meet standards of the American Bureau of Shipping (ABS) Steel Vessel Rules.

Second, this proposed rule would simplify the electrical cable construction requirements in subpart 111.60 so they are similar to the classification society requirements currently accepted without supplement under the Coast Guard's Alternate Compliance Program.

Third, for classifications of hazardous locations in subpart 111.105, this proposed rule would accept the International Electrotechnical Commission's (IEC) 60092-502 as an alternative classification. This is an internationally accepted standard and we are not aware of any notable casualty history attributed to its use as compared to vessels complying with the current applicable U.S. regulations for classification of hazardous locations.

Fourth, this proposed rule would amend 46 CFR 112.05 to allow the use of an emergency generator in port. This optional capability to use emergency generators in port would be acceptable if a set of additional safeguards, approved by the International Maritime Organization (IMO) in 2005 are provided to ensure the availability of emergency power.

The following table provides an overview of the types of proposed changes and the affected sections.

Table 1—Title 46 CFR Sections Affected by the Proposed Rule

Category
Proposed changes
Affected title 46 CFR sections

Incorporated by Reference (IBR) Standards
Editorial
§§ 110.15-1, 111.01-15, 111.05-9, 111.12-3, 111.12-5, 111.12-7, 111.20-15, 111.30-1, 111.30-5, 111.30-19, 111.33-3, 111.33-5, 111.33-11, 111.35-1, 111.40-1, 111.50-3, 111.50-5, 111.50-7, 111.50-9, 111.60-1, 111.60-2, 111.60-3, 111.60-6, 111.60-11, 111.60-13, 111.60-19, 111.60-21, 111.70-1, , 111.75-17, 111.75-20, 111.99-5, 111.105-7, 111.105-9, 111.105-11, 111.105-17, 111.105-19, 111.105-31, 111.105-35, 111.105-40, 111.105-41, 111.105-45, 111.106-3, 111.106-5, 111.106-7, 111.106-13, 111.106-15, 111.107-1, 111.108-1, 111.108-3, 112.50-1, 113.10-7, 113.20-1, 113.25-1, 113.30-25, 113.30-25, 113.30-25, 113.37-10, 113.40-10, 113.65-5.

Updating to latest edition with changes in technical content
§§ 110.15-1, 111.12-1, 111.12-7, 111.15-2, 111.51-5, 111.54-1, 111.55-1, 111.59-1, 111.60-5, 111.60-7, 111.60-11, 111.60-13, 111.60-23, 111.70-1, 1111.70-3, 111.75-18, 111.81-1, 111.105-7, 111.105-11, 111.105-33, 111.105-37, 111.105-39, 111.106-3, 111.107-1, 111.108-3, 113.05-7.

Providing additional options
§§ 110.15-1, 111.01-9, 111.15-10, 111.20-15, 111.30-5, 111.30-19, 111.50-3, 111.53-1, 111.59-1, 111.60-1, 111.60-9, 111.60-13, 111.75-17, 111.75-20, 111.81-1, 111.83-7, 111.87-3, 111.105-7, 111.105-11, 111.105-17, 111.105-28, 111.105-29, 111.105-50, 111.106-3, 111.106-5, 111.108-3, 112.05-7, 113.05-7, 113.10-7, 113.20-1, 113.25-11, 113.30-25, 113.37-10, 113.40-10.

Generator prime mover alarms and shutdowns
Removing unique Coast Guard requirements
§ 111.12-1.

Electrical cable requirements
Proposing additional option
§ 111.60-1.

Removing prescriptive requirements (existing sections)
§§ 111.60-1, 111.60-2, 111.60-3, 111.60-6, 111.105-50.

Classification of hazardous location
Proposing additional options
§§ 111.105-7, 111.105-17, 111.105-28.

Editorial—Harmonizing requirements between subparts
§§ 111.105-1, 111.105-3, 111.105-7, 111.105-9, 111.105-11, 111.105-15 (existing), 111.105-17, 111.105-31, 111.106-3, 111.108-3.

Emergency generator
Allowing use in port
§ 112.05-7.

Revising alarms and shutdowns
§ 112.50-1.

Editorial changes (Other than IBR standards)

§§ 110.15-1, 110.25-1, 110.25-3, 111.05-3, 111.05-37, 111.10-1, 111.10-9, 111.12-11, 111.12-13, 111.15-25, 111.15-30, 111.30-5, 111.30-25, 111.30-27, 111.30-29, 111.33-1, 111.33-3, 111.33-5, 111.33-7, 111.33-9, 111.33-11, 111.50-3, 111.51-1, 111.51-2, 111.51-3, 111.51-6, 111.52, 111.60-7, 111.95-1, 111.99-3, 111.103, 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.107-1, 111.105-15, 111.105-32, 111.107-1, 112.01-20, 112.05-5, 112.15-1, 112.50-1.

IV. Basis and Purpose

The legal basis of this proposed rulemaking is section 1333(d) of Title 43, United States Code (U.S.C.), sections 3306 and 3703 of Title 46 U.S.C., and the Department of Homeland Security (DHS) Delegation No. 0170.1. The provisions of 43 U.S.C. 1333(d) grant the Secretary of the Department in which the Coast Guard is operating the authority to promulgate and enforce regulations with respect to lights and other warning devices, safety equipment, and other matters relating to the promotion of safety of life and property on artificial islands, installations, and other devices. Section 46 U.S.C. 3306(a)(1) authorizes the Secretary to prescribe regulations for the design, construction, alteration, repair, and operation of vessels subject to inspection, including equipment, appliances, propulsion machinery, auxiliary machinery, boilers, unfired pressure vessels, piping, and electric installations. Additionally, 46 U.S.C. 3703 grants the Secretary authority to regulate the construction, alteration, repair, maintenance, operation, and equipping of vessels, that may be necessary for increased protection against hazards to life and property, for navigation and vessel safety, and for enhanced protection of the marine environment. These authorities have been delegated to the Coast Guard by the DHS Security Delegation No. 0170.1(II)(92)(b).

The purpose of this proposed rulemaking is to update the standards that are incorporated by reference in 46 CFR subchapter J, which provide detailed specifications for electrical equipment used by vessels. Newly published editions of the international standards referenced in subchapter J address new technologies and changes in best practices. The Office of Management and Budget (OMB) Circular A-119 states agencies should undertake a review of the standards incorporated by reference every 3 to 5 years to remain current with technological changes. OMB encourages reducing reliance on unique government standards when an existing voluntary consensus standard would suffice. This proposed rule follows the Circular by incorporating newer editions of industry standards and reducing the reliance on unique Coast Guard standards where industry standards are sufficient.

V. Background

Title 46 CFR subchapter J contains the electrical engineering regulations and standards applicable to vessels and required shipboard systems regulated under subchapters D, H, I, I-A, K, L, O, Q, R, T, U, and W of Title 46. A key component of subchapter J is the standards that are incorporated by reference (IBR) in 46 CFR 110.10-1 and cross-referenced throughout parts 110, 111, 112, and 113. The IBR section in subchapter J was last amended by the 2015 final rule titled “Electrical Equipment in Hazardous Locations” (80 FR 16980, Mar. 31, 2015), but because of its limited scope, that rule did not update all of the standards to reflect newer editions. Many of the IBR standards have not been updated since 2008 when the Coast Guard issued the final rule titled “Review and Update of Standards for Marine Equipment” (73 FR 65156, Oct. 31, 2008).

Furthermore, the interim rule titled “Offshore Supply Vessels of at Least 6,000 GT ITC” (79 FR 48893, Aug. 18, 2014) and the “Electrical Equipment in Hazardous Locations” final rule (80 FR 16980, Mar. 31, 2015) amended subchapter J by adding the hazardous location regulations in subparts 111.106 and 111.108 for types of vessels and facilities not covered under subpart 111.105. Vessels and facilities regulated under 111.106 and 111.108 have a broader and more current selection of IBR standards because there were more recent standards to include with those rulemakings. This proposed rule would amend subparts 111.105, 111.106 and 111.108 to ensure all vessel types are offered the broadest and most current selection of IBR explosion protection standards.

Shipboard electrical systems are becoming increasingly complex due to the development of power electronics and computer control systems. In response, many of the standards incorporated by reference have been superseded by newer editions to address the newer electrical equipment. In some cases, the later editions reflect more modern technologies, terminology, and practices that are already in use by industry. Adopting newer versions of these standards would reduce the number of equivalency requests from industry to the Coast Guard, which is expected to produce cost savings. The incorporation of more recent editions also ensures the latest industry practices and advancements in technology are addressed in regulations.

VI. Discussion of Proposed Rule

A. Proposed Revisions to § 110.10-1 Incorporation by Reference

Currently, all of the standards that are incorporated by reference in subchapter J are listed in § 110.10-1. Within this section, the Coast Guard proposes to update the technical standards to reflect the more recent editions of the standards available to the public. We encourage the use of these updated standards because they reflect the best available technologies, practices, and procedures that are recommended by consensus bodies and other groups with experience in the industry. As the baseline upon which other standards, rules, and equivalency requests are evaluated, it is important that subchapter J incorporates up-to-date references.

The class rules of the American Bureau of Shipping (ABS), in particular, are incorporated by reference in multiple locations within subchapter J and throughout 46 CFR Chapter I. It is important to note that while these rules set the regulatory baseline or standard for specific engineering systems and equipment, the Coast Guard also designated several other authorized classification societies in accordance with 46 CFR part 8. These classification societies are listed on the Coast Guard website.
1

The Coast Guard authorized the listed classification societies to perform certain functions and certifications using their respective class rules on vessels enrolled in the Alternate Compliance Program. Vessels not enrolled in the Alternate Compliance Program may propose using the class rules of an authorized classification society as an alternative to the ABS class rules incorporated by reference for particular engineering systems and equipment in accordance with § 110.20-1.

1

See https://www.dco.uscg.mil/Our-Organization/Assistant-Commandant-for-Prevention-Policy-CG-5P/Inspections-Compliance-CG-5PC-/Commercial-Vessel-Compliance/Flag-State-Control-Division/ClassSocAuth/
.

Throughout § 110.10-1, we also propose additional standards to provide alternative compliance options, remove outdated standards, and clarify existing requirements. Where applicable, this proposed rule would also update the naming format, mailing addresses, phone numbers, and URL addresses for the standards already incorporated by reference. These updates will ensure that the standards are reasonably accessible to the public.

Following this paragraph, we list the standards we propose to update, add, or delete in § 110.10-1. Within each standard listed, we describe the topics covered by the standard, the proposed changes to the standard, any differences between currently incorporated IBR standards, and a list of the subparts or sections that reference the IBR standard. If this proposed rule does not propose any changes to a standard that is

currently incorporated by reference, the standard will not be discussed in the proposed revisions to § 110.10-1. However, it will be included, without change, in the proposed regulatory text that appears at the end of this document.

•
ABS Rules for Building and Classing Marine Vessels (ABS Marine Vessel Rules), 2020.
The ABS is a vessel classification society that develops and publishes rules for the construction and maintenance of ships and offshore facilities. Subchapter J references these rules in numerous sections as an option for the design of certain systems including generators, semiconductor rectifiers, and electric propulsion systems. Specifically, we currently reference the 2003 edition in §§ 110.15-1(b), 111.01-9(b), 111.12-3, 111.12-5, 111.12-7, 111.33-11, 111.35-1, 111.70-1(a), 111.105-31(n), 111.105-39(a), 111.105-40, and 113.05-7(a). In 2020, ABS transitioned from the ABS Steel Vessel Rules to the ABS Marine Vessel Rules. This allowed ABS to consolidate several rules into one foundational rule. We propose to incorporate by reference the 2020 ABS Marine Vessel Rules in the aforementioned sections and additionally in the new proposed § 112.05-7(c) related to use of emergency generators in port. The ABS Marine Vessel Rules undergo an annual review and approval process by ABS technical committees. The Coast Guard participates on these committees, which are comprised of international experts with relevant experience. Several of the sections of the ABS Marine Vessel Rules that we propose to incorporate by reference have been individually updated. For example:

○ ABS Marine Vessel Rules 4-8-3/Table 2: This table specifies minimum degrees of protection for electrical equipment. This updated table contains several technical updates since 2003 edition, including additional notes concerning areas protected by fixed water-spray or water mist fire extinguishing systems, and equipment subject to water splash.

○ ABS Marine Vessel Rules 4-8-3: We reference this section for generator construction requirements. The updated edition contains technical updates to account for changes in technology since the 2003 edition.

○ ABS Marine Vessel Rules 4-8-5/5.17.9: This section regarding semiconductor rectifiers now requires a high temperature alarm.

○ ABS Marine Vessel Rules 4-8-5/5.5: This edition contains updates to propulsion generator requirements.

○ ABS Marine Vessel Rules 4-8-2/9.17: This edition updates the requirements for protection of motor circuits to address athwartship thruster motor load alarms and more clearly defines the systems requiring undervoltage release.

○ ABS Marine Vessel Rules 4-8-3/5: This updated section regarding switchboards and motor controllers contains additional cable connection requirements, optional alternative creepage and clearance distances, and additional requirements on battery and uninterruptible power systems based on advancements in technology.

○ ABS Marine Vessel Rules 5-10-4/3: This section regarding roll-on/roll-off cargo spaces is now titled 5C-10-4/3. The new edition made updates to ventilation requirements and to the tables of dangerous goods.

○ ABS Marine Vessel Rules 4-9-7/Table 9: This table regarding equipment testing is now titled 4-9-8/Table 1. The updates to this table reflect changes in technology and industry testing practices.

•
ABS Rules for Building and Classing Mobile Offshore Units (ABS MOU Rules), Part 4 Machinery and Systems, 2020.
ABS also develops and publishes rules for the construction and maintenance of mobile offshore drilling units. Subchapter J references these rules in numerous sections as an option for design of certain systems including generator, semiconductor rectifier, and electric propulsion systems. Specifically, we currently reference the 2001 edition in §§ 111.12-1(a), 111.12-3, 111.12-5, 111.12-7(c), 111.33-11, 111.35-1, and 111.70-1(a). In 2020, ABS transitioned from the ABS Mobile Offshore Drilling Units Rules to the ABS MOU Rules. This allowed ABS to consolidate several rules into one foundational rule. We propose to incorporate by reference the 2020 ABS MOU Rules. Like the ABS Marine Vessel Rules, the ABS MOU Rules will undergo a regular review and approval process by the ABS technical committees comprised of international experts with relevant experience. ABS updated and changed the title of several of the ABS MOU rules incorporated by reference in these sections. For example:

○ ABS MOU Rules 4-3-4 (renamed ABS MOU Rules 6-1-7): We reference this section regarding generator construction requirements. ABS made several technical updates since the 2001 edition to account for changes in technology.

○ ABS MOU Rules 4-3-4/3.5.3 (renamed 6-1-7/12): We reference this section, for semiconductor converters requirements. ABS made several updates to the standard due to changes in technology.

○ ABS MOU Rules 4-3-4/7.1 (renamed 6-1-7/9.9): We reference this section regarding bus bars and wiring requirements. ABS made several updates to the section since the 2001 edition.

•
American National Standards Institute (ANSI) and Institute of Electrical and Electronic Engineers (IEEE) ANSI/IEEE C37.12-1991—American National Standard for Alternating Current (AC) High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis-Specifications Guide.
We propose to remove this standard from § 111.54-1 because IEEE changed the title and republished it with updates in 2008 as IEEE C37.12-2008—IEEE Guide for Specifications of High-Voltage Circuit Breakers (over 1,000 Volts), 2008. This represented a complete technical revision of the standard. IEEE subsequently revised it again in 2018. We are proposing to incorporate by reference IEEE C37.12-2018 in § 111.54-1 and further discuss this standard with the other IEEE standards incorporated by reference.

•
ANSI/IEEE C37.27-1987 (IEEE 331)—Application Guide for Low-Voltage AC Nonintegrally Fused Power Circuitbreakers (Using Separately Mounted Current-Limiting Fuses).
We are proposing to remove the reference to this standard in § 111.54-1 because this guide was replaced by IEEE C37.27-2015—IEEE Guide for Low-Voltage AC (635 V and below) Power Circuit Breakers Applied with Separately-Mounted Current-Limiting Fuses, 2015. We discuss this standard, IEEE C37.27-2015, with the other IEEE standards incorporated by reference.

•
ANSI/International Society of Automation (ISA) 12.12.01-2015—Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Divisions 1 and 2 Hazardous (Classified) Locations.
The purpose of this standard is to provide minimum requirements for the design, construction, and marking of electrical equipment or parts of such equipment for use in Class I and Class II, Division 2 and Class III, Divisions 1 and 2 hazardous (classified) locations. This newer edition of the standard would replace ANSI/ISA 12.12.01-2012 which the Coast Guard recently added to § 111.108-3(b) as part of a separate rulemaking titled “Electrical Equipment in Hazardous Locations” (80 FR 16980, Mar. 31, 2015). Additionally, we propose to include ANSI/ISA 12.12.01-2015 in §§ 111.105-7(a) and 111.106-3(b) as another certification option for electrical equipment in hazardous location. The 2015 edition contains

minor technical changes from the 2012 edition.

•
ANSI/ISA-60079-18—Explosive atmospheres—Part 18: Equipment protection by encapsulation “m”, Third Edition, 2012.
This standard gives the specific requirements for the construction, testing, and marking of electrical equipment and parts of electrical equipment, and for the designation of explosion-protected electrical apparatus complying with IEC standards (Ex) components (which is part of an electrical equipment module found in the European hazardous area scheme) with the type of protection encapsulation “m” intended for use in explosive gas atmospheres or explosive dust atmospheres. We currently reference the 2009 edition of this standard in § 111.106-3(d), and the 2012 edition in § 111.108-3(e). This proposed rule would remove the ANSI/ISA-60079-18 references in §§ 111.106-3(d) and 111.108-3(e) because it has been withdrawn and replaced by UL 60079-18, a substantively similar standard. We propose replacing the ANSI/ISA standard with UL 60079-18 in § 111.106-3(d) and 111.108-3(e).

•
American Petroleum Institute (API) Recommended Practice API RP 14F—Recommended Practice for Design, Installation, and Maintenance of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class 1, Division 1 and Division 2 Locations, Sixth Edition, October 2018.
This document recommends minimum requirements and guidelines for the design, installation, and maintenance of electrical systems on fixed and floating petroleum facilities located offshore. We propose to reference clause 6.8 of the document in § 111.105-17. This clause provides guidance on use of conduit, cable seals, and sealing methods. The incorporation of this standard would add another wiring option in hazardous locations.

•
API RP 14FZ—Recommended Practice for Design, Installation, and Maintenance of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class I, Zone 0, Zone 1 and Zone 2 Locations, Second Edition, May 2013.
This document recommends minimum requirements and guidelines for the design, installation, and maintenance of electrical systems on fixed and floating petroleum facilities located offshore. We propose to reference clause 6.8 of the document in § 111.105-17. This clause provides guidance on use of conduit, cable seals, and sealing methods. The incorporation of this standard would add another wiring option in hazardous locations.

•
API RP 500—Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Division 1 and Division 2, Third Edition, December 2012.
This recommended practice provides guidelines for classifying locations at petroleum facilities as Class I, Division 1 and Class I, Division 2 locations for the selection and installation of electrical equipment. We currently reference the second edition (1997) of this standard in §§ 111.106-7(a) and 111.106-13(b). We propose to reference the more recent, third edition (2012) in those sections. The 2012 edition contains editorial changes, but the technical content has not changed.

•
API RP 505—Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Zone 0, Zone 1, and Zone 2, Second Edition, August 2018.
The purpose of this recommended practice is to provide guidelines for classifying locations Class I, Zone 0, Zone 1, and Zone 2 at petroleum facilities for the selection and installation of electrical equipment. We currently reference the first edition, which was published in 1997 and reaffirmed in 2013, in § 111.106-7(a) and 111.106-13(b). We propose to reference the more recent, second edition (2018) in those sections. This will not substantively change to the requirements of those sections.

•
American Society of Mechanical Engineers (ASME) A17.1-2016/CSA B44-16—Safety Code for Elevators and Escalators, 2016.
This code covers the design, construction, operation, inspection, testing, maintenance, alteration, and repair of elevators, hoists, escalators and their associated parts, rooms, and spaces. We currently reference the sixteenth edition (2000) in § 111.91-1. We propose to reference the more recent, twenty-first edition (2016) in that section. ASME updated this standard based on changes in technology. The updated standard addresses new types of elevators being used in the industry, specifically wind turbine elevators and outside emergency elevators. In addition, the standard contains new requirements to address a new feature called “Elevator Evacuation Operation” that allows for the use of elevators for occupant evacuation. Moreover, there are several major changes to the standard that include seismic requirements, updated maintenance control program requirements, and revisions regarding qualifications for elevator inspectors. ASME A17 has been an industry accepted standard since 1921. Although many of the changes to the presently incorporated edition of the standard do not apply to shipboard elevators, it is important that shipboard elevators meet the updated provisions that do apply.

•
ASTM International (ASTM) B117-19—Standard Practice for Operating Salt Spray (Fog) Apparatus, 2019.
This practice covers the apparatus, procedure, and conditions required to create and maintain the salt spray (fog) test environment. Where the Coast Guard's regulations require material to be corrosion resistant it must meet the testing requirements of this ASTM standard practice. We currently reference the 1997 edition in § 110.15-1(b). We propose to reference the current 2019 edition. The 1997 edition has been superseded by several subsequent editions. The testing specifications in the 2011 edition are similar to those in the 1997 edition, but the 2011 edition is more detailed. For example, the impurity restrictions are more detailed in section 8, the air supply requirements are more specific in section 9, and the conditions in the salt chamber are more precisely described in section 10. The 2016 edition added a warning about the impact of water conductivity in section 4 while the 2019 edition added several minor but non-substantive explanatory sections. Overall, the 2019 edition of this testing standard practice for operating salt spray apparatus is very similar to the 1997 edition currently incorporated, with minor improvements in the specifications to ensure testing consistency and precision.

•
ASTM F2876-10—Standard Practice for Thermal Rating and Installation of Internal Combustion Engine Packages for use in Hazardous Locations in Marine Applications, Reapproved 2015.
This practice covers the method of testing, rating and installing internal combustion engine packages for use in hazardous areas in marine applications. We currently reference the 2010 edition of this standard in §§ 111.106-3(h) and 111.108-3(g). We also propose to reference the 2010 edition in newly proposed § 111.105-28 regarding internal combustion engines. This will ensure a consistent standard for these installations on all vessel and facility types.

•
Canadian Standards Association (CSA) C22.2 No. 30-M1986—Explosion-proof enclosures for use in class I hazardous locations, Reaffirmed 2016.
This standard covers the details of construction and tests for explosion-proof enclosures for electrical

equipment to be used in Class I, Division 1, Groups A, B, C, and D hazardous locations and in gaseous mines. We currently reference the 1986 edition of this standard in §§ 111.106-3(b) and 111.108-3(b) and propose to incorporate the reaffirmed version therein. The two versions are not substantively different. We propose to also reference this reaffirmed standard in § 111.105-7(a), regarding approved equipment, as an additional compliance option. This will afford the broadest and most current selection of IBR explosion protection standards for all vessel and facility types.

•
CSA C22.2 No. 213-16—Nonincendive electrical equipment for use in class I, division 2 hazardous locations, May 2016.
This standard applies to electrical equipment for use in Class I and II, Division 2 and Class III, Division 1 and 2 hazardous locations. We currently reference the 1987 edition in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the 2016 edition in these sections and also reference it in § 111.105-7(a) concerning approved equipment. This standard received a major revision since the 1987 edition based on advances in technology and changes to related standards. It is an accepted national standard and one of several available standards for nonincendive electrical equipment. Our incorporation of this updated edition ensures use of latest industry practices and including it in § 111.105-7 will ensure that standards are consistent for electrical installations on all vessel and facility types.

•
CSA-C22.2 No. 0-10—General requirements—Canadian Electrical Code, Part II, Reaffirmed 2015.
This standard covers definitions, construction requirements, marking, and tests of a general nature that applies to all or several of the individual standards of the Canadian Electrical Code. We currently reference the ninth edition of this standard in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the tenth edition, reaffirmed in 2015, in these sections and in § 111.105-7(a) concerning approved equipment. The tenth edition includes new requirements for equipment containing lasers or lithium batteries, criteria for the use of adhesives in the construction of electrical equipment, surface temperature limits, attachment plug loading, and the maximum temperature of equipment in contact with gypsum. Additionally, it incorporates a comprehensive list of definitions for use in standards for electrical products and outlines the relationship between this standard and electrical product standards. We propose incorporating the more recent edition in subpart 111.105 to ensure that standards are consistent for electrical installations on all vessel and facility types.

•
Canadian National Standard (CAN)/CSA-C22.2 No. 157-92—Intrinsically safe and nonincendive equipment for use in hazardous locations, reaffirmed 2016.
This standard specifies the testing of nonincendive electrical equipment and the details of construction and tests for intrinsically safe electrical equipment for use in hazardous locations. We currently reference the 1992 edition of this standard in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the reaffirmed 1992 edition in those sections as well as § 111.105-7(a) concerning approved equipment. The two editions of the standard are not substantively different and incorporating it into § 111.105-7 would provide an additional option for vessels and facilities.

•
MIL-DTL-24640C with Supplement 1—Detail Specification Cables, Lightweight, Low Smoke, Electric, for Shipboard Use, General Specification for, Nov. 18, 2011.
This specification covers lightweight, low smoke, electric cables for Navy shipboard applications. MIL-DTL-24640C is already incorporated by reference and approved for § 111.106-5(a). However, MIL-DTL-24640C supersedes MIL-C-24640A (1996), currently referenced in §§ 111.60-1 and 111.60-3. We propose to incorporate the updated edition, MIL-DTL-24640C (2011), into § 111.60-1 only, because this proposed rule would delete § 111.60-3. The updated edition, published in 2011, incorporates the latest developments in marine cable materials and performance enhancements but will not substantively change requirements.

•
MIL-DTL-24643C with Supplement 1A—Detail Specification Cables, Electric, Low Smoke Halogen-Free, for Shipboard Use, General Specification for, Oct. 1, 2009 (including Supplement 1A dated Dec. 13, 2011).
This specification is already incorporated by reference in § 111.106-5(a) and covers low smoke halogen-free electric cable for Navy shipboard applications. This specification supersedes the currently referenced MIL-C-24643A (1996) incorporated by reference in §§ 111.60-1 and 111.60-3. We propose to delete MIL-C-24643A (1996) and incorporate the latest standard MIL-DTL-24643C (2011) into § 111.60-1 only, because this proposed rule would delete § 111.60-3. This updated edition, published in 2011, incorporates the latest developments in marine cable materials and performance enhancements.

•
MIL-DTL-76E—Military Specification Wire and Cable, Hookup, Electrical, Insulated, General Specification for, Nov. 3, 2016.
This specification covers single-conductor, synthetic-resin insulated, electrical hookup wire and cable for use in the internal wiring of electrical and electronic equipment. We currently reference MIL-W-76D in 111.60-11. In 2016 the standard was revised and renamed MIL-DTL-76E. This edition has formatting changes and minor updates based on current technology. We propose to incorporate this revised standard as one of several available standards for wire.

•
EN 14744—Inland navigation vessels and sea-going vessels—Navigation light, August 2005.
This standard, developed by the European Committee for Standardization, applies to their testing. We propose it as an acceptable alternate standard for navigation lights in § 111.75-17(d)(2).

•
FM Approvals Class Number 3600—Approval Standard for Electric Equipment for use in Hazardous (Classified) Locations—General Requirements, 2018.
This standard identifies the basis for approval of electrical equipment in hazardous (classified) locations. It is used in conjunction with the other FM Approvals standards referenced in subchapter J. We currently reference the 1998 edition of this standard in §§ 111.106-3(b) and 111.108-3(b). We propose the more recent 2018 edition for §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This edition includes transitioning from ISA series of standards to UL standards, an expanded list of normative references, and more specificity regarding the required quality control system. The incorporation of this more recent edition ensures use of the latest industry practices and including it in § 111.105-7(a) regarding approved equipment will ensure that standards are consistent for electrical installations on all vessel and facility types.

•
FM Approvals Class Number 3610—Approval Standard for Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III, Division 1, Hazardous (Classified) Locations, January 2018.
This standard provides requirements for the construction and testing of electrical apparatus, or parts of such apparatus, whose circuits are incapable of causing ignition in Classes I, II, and III, Division 1 hazardous (classified) locations. We currently reference the 2004 edition of this standard in §§ 111.106-3(b) and

111.108-3(b). We are proposing to incorporate the more recent 2018 edition in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The incorporation of this more recent edition ensures use of latest industry practices and including it in § 111.105-7(a) regarding approved equipment will ensure that standards are consistent for electrical installations on all vessel and facility types.

•
FM Approvals Class Number 3611—Approval Standard for Nonincendive Electrical Equipment for Use in Class I and II, Division 2, and Class III, Divisions 1 and 2, Hazardous (Classified) Locations, January 2018.
This standard provides requirements for the construction and testing of electrical apparatus, or parts of such apparatus, whose circuits are incapable of causing ignition in Class I and II, Division 2, and Class III, Divisions 1 and 2 hazardous (classified) locations. This standard is currently referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to add this as an alternative standard in § 111.105-7(a) concerning approved equipment. This will ensure that standards are consistent for electrical installations on all vessel and facility types.

•
FM Approvals Class Number 3615—Approval Standard for Explosionproof Electrical Equipment General Requirements, January 2018.
This standard contains the basic requirements for the construction and testing of explosion proof electrical apparatus. This standard is currently referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to add this as an alternative standard in § 111.105-7(a) regarding approved equipment. This will ensure that standards are consistent for electrical installations on all vessel and facility types.

•
FM Approvals Class Number 3620—Approval Standard for Purged and Pressurized Electrical Equipment for Hazardous (Classified) Locations, January 2018.
This standard contains the basic requirements for the construction and testing of purged and pressurized electrical equipment. We currently reference the 2000 edition of this standard in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the 2018 edition in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The two editions of the standard are not substantively different and adding it to § 111.105-7(a) will ensure consistent standards for electrical installations on all vessel and facility types.

•
IEEE C37.04-2018—IEEE Standard for Ratings and Requirements for AC High-Voltage Circuit Breakers with Rated Maximum Voltage above 1000 V, 2018.
This document establishes a rating structure, preferred ratings, construction and functional component requirements for high-voltage AC circuit breakers. We currently reference the 1999 edition of this standard in § 111.54-1. We propose to adopt the more recent, 2016 edition in § 111.54-1. This edition contains updates that reflect current circuit breaker manufacturing technology.

•
IEEE C37.010-2016—IEEE Application Guide for AC High-Voltage Circuit Breakers > 1000 Vac Rated on a Symmetrical Current Basis, 2016.
This document provides guidance for the application of high-voltage circuit breakers. We currently reference the 1999 edition of this standard in § 111.54-1. We propose to adopt the more recent 2016 edition in § 111.54-1. This edition contains updates that reflect current circuit breaker manufacturing technology.

•
IEEE C37.12-2018—IEEE Guide for Specifications of High-Voltage Circuit Breakers (over 1000 V), 2018.
These specifications apply to all indoor and outdoor types of AC high-voltage circuit breakers rate above 1000 volts (V). It replaces ANSI/IEEE C37.12-1991. IEEE C37.12-2018 represents a nearly complete rewrite of 1991 edition to reflect present circuit breaker manufacturing technology. The 2018 edition of this standard would be one of several acceptable circuit breaker standards listed in § 111.54-1.

•
IEEE C37.13-2015—IEEE Standard for Low-Voltage AC Power Circuit Breakers Used in Enclosures, 5 Dec. 2015.
This standard establishes minimal functional requirements, establishes preferred rating structure, and provides preferred ratings enclosed low-voltage AC power circuit breakers. We currently reference the 2000 edition of this standard in § 111.54-1. We propose to reference the more recent 2015 edition in § 111.54-1. This edition has many technical updates to address advancements in technology, including an increase in nominal voltages, new testing techniques, and removal of information on direct current (DC) circuit-breakers (now located in IEEE C37.14). This standard is one of several acceptable circuit-breaker standards in § 111.54-1.

•
IEEE C37.14-2015—IEEE Standard for DC (3200 V and below) Power Circuit Breakers Used in Enclosures, 26 Mar. 2015.
This standard covers the preferred ratings and testing requirements of enclosed DC power circuit breakers. We currently reference the 2003 edition of this standard § 111.54-1. We propose to reference the more recent 2015 edition in § 111.54-1, which contains many technical changes to reflect present circuit breaker manufacturing technology and advancements in technology.

•
IEEE C37.27-2015—IEEE Guide for Low-Voltage AC (635 V and below) Power Circuit Breakers Applied with Separately-Mounted Current-Limiting Fuses, 2015.
This guide sets forth recommendations for the selection of current-limiting fuses for use in combination with low-voltage AC power circuit breakers. This guide replaces ANSI/IEEE C37.27-1987 which we currently reference in § 111.54-1. IEEE C37.27-2015 contains many technical updates to address advancements in circuit breaker manufacturing technology, which would provide the public with more accurate and applicable standards for modern circuit breakers than the previous 1987 edition. We propose incorporating this guide as one of several acceptable circuit breaker standards listed in § 111.54-1.

•
IEEE 45-1998—IEEE Recommended Practice for Electric Installations on Shipboard—1998.
IEEE 45-2002 superseded the subject 1998 edition, but in some instances the Coast Guard previously found the 1998 edition preferable and continued to reference it. Because the 1998 edition is no longer supported by IEEE and other acceptable standards exist where it is referenced, we propose to delete all references to this standard, which includes §§ 111.30-19, 111.105-3, 111.105-31, and 111.105-41.

•
IEEE 45-2002—IEEE Recommended Practice for Electrical Installations On Shipboard—2002.
We currently reference this edition of IEEE 45 in the following sections in subchapter J: §§ 111.05-7, 111.15-2, 111.30-1, 111.30-5, 111.33-3, 111.33-5, 111.40-1, 111.60-1, 111.60-3, 111.60-5, 111.60-11, 111.60-13, 111.60-19, 1111.60-21, 111.60-23, 111.75-5, and 113.65-5. IEEE has developed the IEEE 45 Series which comprises nine recommended practices addressing electrical installations on ships and marine platforms. We propose to replace references to IEEE 45-2002 with newer IEEE 45 Series recommended practices individually discussed below, and remove all references to the IEEE 45-2002.

•
IEEE 45.1-2017—IEEE Recommended Practice for Electrical Installations On Shipboard—Design, 23 Mar. 2017.
This recommended practice provides guidance for electrical power generation, distribution, and electric propulsion system design. These recommendations reflect the present-day technologies, engineering methods, and engineering practices. We propose

to reference these standards in §§ 111.15-2, 111.40-1, 111.75-5, and 113.65-5. The technical content is similar to IEEE 45-2002, which we propose to delete from these sections. We also propose to add reference to this standard in § 111.105-41 concerning battery rooms.

•
IEEE 45.2-2011—IEEE Recommended Practice for Electrical Installations On Shipboard—Controls and Automation, 1 Dec. 2011.
This recommended practice provides guidance for shipboard controls, control applications, control apparatus, and automation. These recommendations reflect present-day technologies, engineering methods, and engineering practices. We propose to reference this document in §§ 111.33-3 and 111.33-5. The technical content is similar to IEEE 45-2002, which we propose to delete from these sections.

•
IEEE 45.6-2016—IEEE Recommended Practice for Electrical Installations on Shipboard—Electrical Testing, 7 Dec. 2016.
This recommended practice provides guidance for electrical testing for power generation, distribution, and electric propulsion systems. These recommendations reflect the present day technologies, engineering methods, and engineering practices. We propose to reference this document in § 111.60-21. Its technical content is similar to IEEE 45-2002, which we propose to delete from this section.

•
IEEE 45.7-2012—IEEE Recommended Practice for Electrical Installations On Shipboard—AC Switchboards, 29 Mar. 2012.
This recommended practice supplements the design, installation, and testing recommendations in IEEE 45-2002. This recommended practice provides new technologies and design practices for generator control panels and switchboards to aid marine electrical engineers in the design, application and installation of this equipment on ships and other marine installations. We propose to reference this document in §§ 111.30-1, 111.30-5, and 111.30-19. The technical content of IEEE 45.7-2012 is similar to IEEE 45-2002, but more detailed. It also references other industry standards, many of which we have incorporated by reference elsewhere in Subchapter J, rather than using prescriptive requirements.

•
IEEE 45.8-2016—IEEE Recommended Practice for Electrical Installations On Shipboard—Cable Systems, 29 Jan. 2016.
This document provides recommendations for selection, application, and installation of electrical power, signal, control, data, and specialty marine cable systems on shipboard systems. These recommendations include the present day technologies, engineering methods, and engineering practices. We propose to replace references to IEEE 45-2002 in §§ 111.05-7, 111.60-5, 111.60-11, 111.60-13, and 111.106-19 with IEEE 45.8-2016. The technical content of IEEE 45.8-2016 is similar to IEEE 45-2002, but more detailed.

•
IEEE 1202-2006—IEEE Standard for Flame-Propagation Testing of Wire and Cable with Corrigendum 1 (21 Nov. 2012), 2006.
This standard provides a protocol for exposing cable samples to a theoretical 20 kilowatt (kW) [(70,000 British thermal units per hour (Btu/hr)] flaming ignition source for a 20 minute test duration. The test determines the flame propagation tendency of single conductor and multi-conductor cables intended for use in cable trays. We currently reference the 1991 edition in §§ 111.60-6 and 111.107-1(c). We propose to reference the more recent 2006 edition in § 111.107-1(c), but not in § 111.60-6, because we are proposing to delete that section on fiber optic cable. In the 2006 edition, the normative references have been updated, the temperature at which cables are conditioned has been raised from 18 °C to 25 °C, and minor refinements to the test procedure have been made.

•
IEEE 1580-2010—IEEE Recommended Practice for Marine Cable for Use on Shipboard and Fixed or Floating Platforms, 2 Mar. 2011.
This recommended practice contains the requirements for single or multiconductor cables, with or without metal armor or jacket, and rated 300 V to 35 kilovolts (kV), intended to be installed aboard marine vessels, and fixed and floating offshore facilities. The 2001 edition is currently referenced in §§ 111.60-1, 111.60-2, 111.60-3, and 111.106-5(a). We propose to reference the more recent 2010 edition only in §§ 111.60-1 and 111.106-5(a), because we propose to delete §§ 111.60-2 and 111.60-3 in this proposed rule. The 2010 edition has been updated to incorporate the latest developments in marine cable materials and performance enhancements.

•
IEC 60068-2-52:2017—Environmental testing Part 2-52: Tests—Test Kb: Salt mist, cyclic (sodium chloride solution), Edition 3.0, 2017-11.
This standard specifies the application of the cyclic salt mist test to components or equipment designed to withstand a salt-laden atmosphere as salt can degrade the performance of parts manufactured using metallic or non-metallic materials. The second edition is referenced in § 110.15-1. We propose to incorporate the third edition. In this more recent edition the standard has been updated to ensure consistency with International Organization for Standardization (ISO) 9227—Corrosion tests in artificial atmospheres—Salt spray tests.

•
IEC 60079-0—Electrical apparatus for Explosive Gas Atmospheres—Part 0: General Requirements, Edition 3.1, 2000.
This part of the IEC 60079 series of standards specifies the general requirements for construction, testing and marking of electrical equipment and Ex components intended for use in explosive atmospheres. This standard was referenced in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7 and 111.105-17. We propose reformatting of subpart 111.105 to be consistent with subparts 111.106 and 111.108. Consequently, we propose to no longer specifically reference IEC 60079-0.

•
IEC 60079-1:2014—Explosive atmospheres—Part 1: Equipment protection by flameproof enclosures “d”, Edition 7.0, 2014-06.
This part of the IEC 60079 series of standards contains specific requirements for the construction and testing of electrical equipment with the type of protection flameproof enclosure “d”, which are intended for use in explosive gas atmospheres. We currently reference the fourth edition (2001) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-9, and 111.105-17 while the sixth edition (2007) is referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to replace all references to the fourth and sixth editions of this standard with the more recent edition 7.0 (2014) in §§ 111.105-7, 111.106-3(b), and 111.108-3(b). The updated standard reflects advances in technology, including:

○ Addition of material limitations of enclosures of equipment and enclosures of Ex components for external mounting;

○ Addition of power factor requirement for evaluating the ability of a plug and socket; to remain flameproof during the arc-quenching period while opening a test circuit; and

○ Addition of marking requirements for Ex component enclosures, in addition to the requirements for marking of Ex components given in IEC 60079-0.

•
IEC 60079-2:2014—Explosive atmospheres—Part 2: Equipment protection by pressurized enclosures “p”, Edition 6.0, 2014-07.
This part of the IEC 60079 series of standards contains specific requirements for the construction and testing of electrical equipment with pressurized enclosures, of type of protection “p”, intended for use in explosive gas atmospheres or

explosive dust atmospheres. It also includes the requirements for pressurized enclosures containing a limited release of a flammable substance. We currently reference the fourth edition (2001) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, and 111.105-17, while the fifth edition (2007) is referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to delete all references to the fourth and fifth edition. The more recent edition 6.0 (2014), is being proposed for incorporation in §§ 111.105-7(a), 111.105-17, 111.106-3(b), and 111.108-3(b). The updated standard now covers combustible dust, cells and batteries, and backup protective gas. The incorporation of the more recent edition ensures consistent, up-to-date standards for electrical installations on all vessel and facility types.

•
IEC 60079-5:2015—Explosive atmospheres—Part 5: Equipment protection by powder filling “q”, Edition 4.0, 2015-02.
This part of the IEC 60079 series of standards contains specific requirements for the construction, testing, and marking of electrical equipment, parts of electrical equipment, and Ex components in the type of protection powder filling “q”, intended for use in explosive gas atmospheres. We currently reference the second edition (1997) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-15, and 111.105-17, while the third edition (2007) is referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to delete all references to the second and third edition. The more recent edition 4.0 (2015), containing minor technical revisions and clarifications, is proposed for §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This will ensure consistent, up-to-date standards for electrical installations on all vessel and facility types but will not result in a substantive change to the current requirements.

•
IEC 60079-6:2015—Explosive atmospheres—Part 6: Equipment protection by liquid immersion “o”, Edition 4.0, 2015-02.
This part of the IEC 60079 series of standards specifies the requirements for the design, construction, testing and marking of Ex equipment and Ex components with type of protection liquid immersion “o” intended for use in explosive gas atmospheres. We currently reference the second edition (1995) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-15, and 111.105-17, while the third edition (2007) is referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to delete all references to the second and third edition. The more recent edition, 4.0 (2015), is being proposed for §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The incorporation of the latest edition ensures consistent, up-to-date standards for electrical installations on all vessel and facility types. The latest edition represents a major technical revision of the requirements for oil immersion “o”. These revisions include:

○ The redefinition of the requirements for oil immersion “o” into liquid immersion levels of protection “ob” and “oc”;

○ The addition of the ability to protect sparking contacts to both “ob” and “oc”; and

○ The introduction of additional requirements for the protective liquid.

•
IEC 60079-7:2017—Explosive atmospheres—Part 7: Equipment protection by increased safety “e”, Edition 5.1, 2017-08.
This part of the IEC 60079 series of standards specifies requirements for the design, construction, testing, and marking of electrical equipment and Ex components with type of protection increased safety “e” intended for use in explosive gas atmospheres. We currently reference the third edition (2001) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-15, and 111.105-17, while the fourth edition (2006) is referenced in § 111.106-3(b) and 111.108-3(b). This proposed rule would remove all references to the third and fourth editions of this standard. The more recent edition 5.1 (2017) edition is being proposed for §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The standard contains updates including the addition of terminal installation tests, the addition of solid insulating material requirements based on thermal stability, and the revision of the requirements for soldered connections. The incorporation of the more recent edition ensures consistent, up-to-date standards for electrical installations.

•
IEC 60079-11:2011—Explosive atmospheres—Part 11: Equipment protection by intrinsic safety “i” with Corrigendum 1 (January 2012), Edition 6.0, 2011-06.
This part of the IEC 60079 series of standards specifies the construction and testing of intrinsically safe apparatus intended for use in an explosive atmosphere and for associated apparatus, which is intended for connection to intrinsically safe circuits that enter such atmospheres. This type of protection applies to electrical equipment in which the electrical circuits themselves are incapable of causing an explosion in the surrounding explosive atmospheres. We currently reference the fourth edition (1999) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-11, and 111.105-17. The fifth edition (2006) referenced in § 111.106-3(b), and the more recent IEC 60079-11:2011, Edition 6.0, is referenced in § 111.108-3(b). We propose the more recent edition 6.0 for §§ 111.105-7(a) and 111.106-3(b), and would continue to be referenced in § 111.108-3(b). The changes with respect to the previous editions are as follows:

○ Inclusion of non-edition specific references to IEC 60079-0;

○ Merging of the apparatus requirements for the Fieldbus Intrinsically Safe Concept (FISCO) from IEC 60079-27;

○ Merging of the requirements for combustible dust atmospheres from IEC 61241-11;

○ Clarification of the requirements for accessories connected to intrinsically safe apparatus (such as chargers and data loggers);

○ Addition of new test requirements for opto-isolators; and

○ Introduction of Annex H about ignition testing of semiconductor limiting power supply circuits.

The incorporation of the more recent edition ensures consistent, up-to-date standards for electrical installations.

•
IEC 60079-13:2017—Explosive atmospheres—Part 13: Equipment protection by pressurized room “p” and artificially ventilated room “v”, Edition 2.0, 2017-05.
This part of the IEC 60079 series of standards gives requirements for the design, construction, assessment and testing, and marking of rooms protected by pressurization. We currently reference Edition 1.0 (2010) of this standard in §§ 111.106-3(b) and 111.108-3(b). We are proposing referencing Edition 2.0 (2017), the more recent edition, in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This standard contains the following changes:

○ Modification of the title to include artificially ventilated room “v” in addition to pressurized room “p”;

○ Addition of protection types (“pb”, “pc”, and “vc”);

○ Removal of protection types (“px”, “py”, “pz” and “pv”);

○ Definition of the differences between pressurization and artificial ventilation types of protection;

○ Removal of protection of rooms with an inert gas or a flammable gas from the scope of standard; and

○ Addition of an informative annex to include examples of applications where types of protection pressurization or artificial ventilation or pressurization

and artificial ventilation can be used and associated guidelines.

The incorporation of the more recent edition ensures consistent, up-to-date standards for electrical installations.

•
IEC 60079-15:2017—Explosive atmospheres—Part 15: Equipment protection by type of protection “n”, Edition 5.0, 2017-12.
This part of the IEC 60079 series of standards specifies requirements for the construction, testing, and marking for Group II electrical equipment with type of protection “n” intended for use in explosive gas atmospheres. This standard applies to non-sparking electrical equipment and also to electrical equipment with parts or circuits producing arcs or sparks or having hot surfaces which, if not protected in one of the ways specified in this standard, could be capable of igniting a surrounding explosive gas atmosphere. We currently reference the second edition (2001) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-15, and 111.105-17, while the edition 4.0 (2010) is referenced in §§ 111.106-3(b) and 111.108-3(b). We are proposing to incorporate by reference the more recent edition 5.0 (2017) in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This standard contains numerous technical changes from the previous version, which reflect changes in industry practices and technology.

•
IEC 60079-18:2017—Explosive atmospheres—Part 18: Equipment protection by encapsulation “m”, Edition 4.1, 2017-08.
This part of the IEC 60079 series of standards gives specific requirements for the construction, testing, and marking of electrical equipment, parts of electrical equipment, and Ex components with the type of protection encapsulation “m” intended for use in explosive gas atmospheres or explosive dust atmospheres. We currently reference the first edition (1992) of this standard in §§ 111.105-1, 111.105-3, 111.105-5, 111.105-7, 111.105-15, and 111.105-17, while the edition 3.0 (2009) is referenced in §§ 111.106-3(b), 111.106-3(d), 111.108-3(b), and 111.108-3(e). We propose the more recent edition 4.1 (2017) for §§ 111.105-7(a), 111.106-3(b), 111.106-3(d), 111.108-3(b) and 111.108-3(e). There have been a few minor technical revisions to the standard including modified and additional requirements for cells and batteries as well as revised testing guidance. The incorporation of the more recent edition ensures consistent, up-to-date standards for electrical installations.

•
IEC 60079-25:2010—Explosive atmospheres—Part 25: Intrinsically safe electrical systems, Edition 2.0, 2010-02.
This part of the IEC 60079 series of standards contains specific requirements for construction and assessment of intrinsically safe electrical systems, type of protection “i”, intended for use, as a whole or in part, in locations in which the use of Group I, II, or III apparatus is required. We currently reference the Edition 2.0 (2010) in §§ 111.106-3(b) and 111.108-3(b). We propose to also reference this standard in § 111.105-7(a) concerning approved equipment. This will ensure that standards are consistent on electrical installations.

•
IEC 60079-30-1 Part 30-1: Electrical resistance trace heating—General and testing requirements, First edition, 2007-01.
This part of the IEC 60079 series of standards specifies general and testing requirements for electrical resistance trace heaters for application in explosive gas atmospheres. This standard covers trace heaters that may be either factory- or field- (work-site) assembled units, which may be series heating cables, parallel heating cables, or heating pads and heating panels that have been assembled or terminated in accordance with the manufacturer's instructions. We propose to reference this newly incorporated standard in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). Given the increased interest in marine operations in the polar regions, this standard provides requirements for surface heating in hazardous locations.

•
IEC 60092-101:2018—Electrical installations in ships—Part 101: Definitions and general requirements, Edition 5.0, 2018-10.
The Edition 4.0 (2002) is referenced in §§ 110.15-1 and 111.81-1. We propose to reference the more recent Edition 5.0 (2018) of this standard. This edition contains many changes including the following:

○ The applicability of the standard has been changed to 1000 V AC and 1500 V DC;

○ The table for design temperature has been simplified;

○ The clause regarding power supply system characteristics has been rewritten; and

○ Information regarding pollution degree has been added in the clause regarding clearance.

•
IEC 60092-201:2019—Electrical installations in ships—Part 201: System design-General, Edition 5.0, 2019-09.
We currently reference fourth edition in §§ 111.70-3 and 111.81-1. We propose to reference the more recent Edition 5.0 (2019) of this standard. This edition contains many changes including the following:

○ Adding a new subclause regarding studies and calculations;

○ Adding a new subclause regarding documentation;

○ Revising the clause regarding distribution systems;

○ Adding a new clause regarding system earthing;

○ Revising the clause regarding sources of electrical power;

○ Revising the clause regarding distribution system requirements;

○ Deleting the clause regarding cables and transferring it to IEC 60092-401; and

○ Adding a new subclause regarding electric and electrohydraulic steering gear.

•
IEC 60092-202:2016—Electrical installations in ships—Part 202: System design-Protection, Edition 5.0, 2016-09.
This standard covers electrical protective system design. We currently reference the fourth edition in §§ 111.12-7, 111.50-3, 111.53-1, and 111.54-1. We propose to reference the more recent edition 5.0 (2016) in those sections. This edition contains substantial technical updates on electrical load studies, short-circuit current calculations, and protection discrimination studies. The incorporation of this edition ensures consistent, up-to-date standards.

•
IEC 60092-301:1980—Electrical installations in ships—Part 301: Equipment—Generators and motors, Third Edition with Amendment 1 (1994-05) and Amendment 2, 1995-04.
This current edition is referenced in §§ 111.12, 111.25, and 111.70. This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60092-302:1997—Electrical installations in ships—Part 302: Low-voltage switchgear and controlgear assemblies, Fourth Edition, 1997-05.
This current edition is referenced in § 111.30. This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60092-303:1980—Electrical installations in ships—Part 303: Equipment—Transformers for power and lighting, Third Edition with amendment 1, 1997-09.
This edition is referenced in § 111.20-15. This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other

referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60092-304:1980—Electrical installations in ships—Part 304: Equipment—Semiconductor convertors, Third Edition with Amendment 1, 1995-04.
This edition is referenced in §§ 111.33-3 and 111.33-5. This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60092-306:2009—Electrical installations in ships—Part 306: Equipment—Luminaires and lighting accessories, Edition 4.0, 2009-11.
This standard applies to luminaires and lighting accessories for use in ships. It applies primarily to luminaires for illumination purposes. This standard also applies to lighting accessories associated with the wiring and current-consuming appliance of an installation. This standard does not apply to portable luminaires, navigation lights, search lights, daylight signaling lamps, signal lights including the relevant control and monitoring equipment and other lights used for navigation in channels, harbors, etc. We currently reference the third edition (1980) of this standard in §§ 111.75-20 and 111.81-1. The Coast Guard is proposing to reference the most recent edition 4.0 (2009) of this standard in §§ 111.75-20 and 111.81-1. The IEC made the following changes to the standard since the 1980 edition:

○ The title was amended;

○ The scope was stated more precisely;

○ Mechanical design and material requirements were amended and stated more precisely;

○ Table 2—Standard types of lamp holders, was amended;

○ Environmental tests, especially regarding shock and vibration, were added;

○ Requirements and tests concerning special chemical and physical attributes were added; and

○ The standard was editorially revised.

•
IEC 60092-350:2014—Electrical installations in ships—Part 350: General construction and test methods of power, control and instrumentation cables for shipboard and offshore applications, Edition 4.0, 2014-08.
This part of the IEC 60092 series of standards provides the general construction requirements and test methods for use in the manufacture of electric power, control and instrumentation cables with copper conductors intended for fixed electrical systems at voltages up to and including 18/30(36) kV on board ships and offshore (mobile and fixed) units. We currently reference Edition 3.0 (2008) of this standard in § 111.106-5(a). We propose to reference the more recent edition, 4.0 (2014), of this standard in § 111.106-5(a) to ensure the latest industry practices based on changes in technology are addressed. The Coast Guard is proposing to amend subpart 111.60 to align with recognized classification society rules and industry practice. In support of this effort, this proposed rule would include IEC 60092-350:2014 in § 111.60-1(a) concerning construction and testing of cable. The 4.0 edition includes the following technical changes as compared to the previous edition:

○ The standard includes a reference to IEC 60092-360 for both the insulating and sheathing compounds;

○ The standard includes partial discharge tests, which were transferred from IEC 60092-354 to align them with IEC 60092-353;

○ The IEC transferred the requirements for oil and drilling-fluid resistance (former Annexes F and G) to IEC 60092-360;

○ The standard contains improved requirements for cold bending and shocks; and

○ The document reflects the changes of material types that were introduced during development of IEC 60092-353 and IEC 60092-360.

•
IEC 60092-352:2005—Electrical installations in ships—Part 352: Choice and Installation of electrical cables, Third Edition, 2005-09.
This part of the IEC 60092 series of standards provides the basic requirements for the choice and installation of cables intended for fixed electrical systems on board ships at voltages up to and including 15 kV. We currently reference the second edition (1997) of this standard in §§ 111.60-3, 111.60-5 and 111.81-1. Because of proposed revisions to subpart 111.60, we propose to reference the more recent third edition (2005) of this standard in § 111.60-1 and 111.60-5. Additionally, IEC 60092-352:2005 would replace the previous 1997 edition referenced in § 111.81-1. The 2005 edition has several minor updates including changes to:

○ Sizes of earth continuity conductors and equipment earthing connections;

○ Bending radii for cables rated at 3,6/6,0 (7,2) kV and above;

○ Current carrying capacities in amperes at core temperatures of 70 °C and 90 °C; and

○ Tabulated current carrying capacities—defined installations.

To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
IEC 60092-353:2016—Electrical installations in ships—Part 353: Power cables for rated voltages 1 kV and 3 kV, Edition 4.0, 2016-09.
This part of the IEC 60092 series of standards provides manufacturing requirements and characteristics of such cables directly or indirectly bearing on safety and specifies test methods for checking conformity with those requirements. We currently reference the second edition (1995) of this standard in §§ 111.60-1, 111.60-3, and 111.60-5 while the third edition (2011) is referenced in § 111.106-5(a). We propose to reference the more recent edition 4.0 (2016) only in §§ 111.60-1(a) and 111.106-5(a), but not § 111.60-3 because we propose to revise subpart 111.60 regarding cable construction. The 2016 edition of this standard includes updates for advancements in insulation and sheathing materials, construction methods, and test methods. Its incorporation ensures consistent, up-to-date standards for electrical cable installations.

•
IEC 60092-354:2014—Electrical installations in ships—Part 354: Single- and three-core power cables with extruded solid insulation for rated voltages 6 kV (U
m
=7.2 kV) up to 30 kV (U
m
=36 kV), Edition 3.0, 2014-08.
This part of the IEC 60092 series of standards provides manufacturing requirements and characteristics of such cables directly or in directly bearing on safety and specifies test methods for checking conformity with those requirements. We propose to reference this standard in § 111.60-1(a). This will align Coast Guard requirements with those of recognized classification society rules and industry practice.

•
IEC 60092-360:2014—Electrical installations in ships—Part 360: Insulating and sheathing materials for shipboard and offshore units, power, control, instrumentation and telecommunication cables, Edition 1.0, 2014-04.
This part of the IEC 60092 series of standards specifies the requirements for electrical, mechanical and particular characteristics of insulating and sheathing materials intended for use in shipboard and fixed and mobile offshore unit power, control, instrumentation, and telecommunication cables. We propose to reference this standard in § 111.60-1(a). This will align Coast Guard requirements with those of recognized classification society rules and industry practice.

•
IEC 60092-376:2017—Electrical installations in ships—Part 376: Cables for control and instrumentation circuits 150/250 V (300 V), Third Edition, 2017-05.
This part of the IEC 60092 series of standards provides manufacturing requirements and characteristics of such cables directly or in directly bearing on safety and specifies test methods for checking conformity with those requirements. We propose to reference this standard in § 111.60-1(a). This will align Coast Guard requirements with those of recognized classification society rules and industry practice.

•
IEC 60092-401:1980—Electrical installations in ships—Part 401: Installation and test of completed Installation, Third Edition with Amendment 1 (1987-02) and Amendment 2 (1995-04).
We currently reference the 1980 edition in §§ 111.05-9 and 111.81-1(d). This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60092-502:1999—Electrical installations in ships—Part 502: Tankers—Special features, Fifth Edition, 1999-02.
This part of the IEC 60092 series of standards deals with the electrical installations in tankers carrying liquids which are flammable, either inherently, or due to their reaction with other substances, or flammable liquefied gases. The standard details the zonal concept for hazardous area classification. We currently reference the 1992 edition in §§ 111.81-1, 111.105-31, 111.106-3(b), 111.106-5(c), 111.106-15(a), and 111.108-3(b). We propose to remove reference to this standard in § 111.105-31 and add it into §§ 111.105-1, 111.105-3(b), 111.105-7(a), 111.105-11(b), 111.105-17(b), 111.105-50(c). This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference. Additionally, we propose to allow classification of hazardous locations based on this document. That proposal is described in more detail in section VI.D later in this discussion of the proposed rule.

•
IEC 60092-503:2007—Electrical installations in ships—Part 503: Special features—A.C. supply systems with voltages in the range of above 1kV up to and including 15 kV, Second edition, 2007-06.
This part of the IEC 60092 series of standards covers the design and installation requirements for AC supply systems with voltages in the range of above 1 kV. We currently reference the first edition (1975) of this standard in § 111.30-5(a). We propose to reference the more recent second edition (2007) of this standard. The second edition covers a greater range of voltages and has updated technical requirements.

•
IEC 60331-11:2009—Tests for electric cables under fire conditions—Circuit integrity—Part 11: Apparatus—Fire alone at a flame temperature of at least 750 °C, Edition 1.1, 2009-07.
This part of IEC 60331 specifies the test apparatus to be used for testing cables required to maintain circuit integrity when subject to fire. We currently reference the first edition (1999) of this standard in § 113.30-25. We propose to reference the more recent 1.1 edition (2009) of this standard, which includes minor technical updating, to ensure the latest industry practices based on changes in technology are addressed.

•
IEC 60331-21:1999—Tests for electric cables under fire conditions—Circuit integrity—Part 21: Procedures and requirements—Cables of rated voltage up to and including 0.6/1.0 kV, First Edition, 1999-04.
We currently reference this 1999 edition in § 113.30-25(j). This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition incorporated by reference.

•
IEC 60332-1-1:2015—Tests on electric and optical fibre cables under fire conditions—Part 1-1: Test for vertical flame propagation for a single insulated wire or cable—Apparatus, First Edition with Amendment 1 (2015-07), 2004-07.
This part of IEC 60332 specifies the apparatus for testing the resistance to vertical flame propagation for a single vertical electrical insulated conductor or cable, or optical cable, under fire conditions. This standard, along with IEC 60332-1-2:2015, supersedes IEC 60332-1:1993 currently referenced in § 111.30-19(b). We propose to replace the superseded 1993 standard in 111.30-19(b) with IEC 60332-1-1:2015 and IEC 60332-1-2:2015. IEC 60332-1-1:2015 covers the test apparatus and IEC 60332-1-2:2015 covers the testing procedure. The technical content is similar to the 1993 edition, but has been updated with greater specificity regarding the ignition source, test sample size, and positioning of the test flame.

•
IEC 60332-1-2:2015—Tests on electric and optical fibre cables under fire conditions—Part 1-2: Test for vertical flame propagation for a single insulated wire or cable—Procedure for 1kW pre-mixed flame, First Edition with Amendment 1, 2015-07.
This part of IEC 60332 specifies the procedure for testing the resistance to vertical flame propagation for a single vertical electrical insulated conductor or cable, or optical cable, under fire conditions. This standard, along with IEC 60332-1-1:2015, supersedes IEC 60332-1:1993, which we currently reference in § 111.30-19(b). We propose to reference IEC 60332-1-2:2015, regarding the testing procedure, in § 111.30-19(b). The technical content is similar to the 1993 edition, but the updates in the standard provide greater specificity regarding the ignition source, test sample size, and positioning of the test flame.

•
IEC 60332-3-21:2018—Tests on electric and optical fibre cables under fire conditions—Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables—Category A F/R, Edition 2.0, 2018-07.
This part of IEC 60332-3 specifies the procedure for testing the resistance to vertical flame propagation for vertically-mounted bunched wires or cables, under defined conditions. Edition 2.0 (2018-7) retains and updates pre-existing categories of tests, adds a new category (category D) for testing at very low non-metallic volumes, and emphasizes that it applies to optical fibre cables as well as metallic conductor cables. We propose this standard for incorporation in §§ 111.60-1(b) and 111.107-1(c).

•
IEC 60332-3-22:2018—Tests on electric cables under fire conditions—Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables—Category A, Edition 2.0, 2018-07.
This part of IEC 60332-3 specifies methods of test for assessment of vertical flame spread of vertically-mounted bunched wires or cables, electrical or optical, under defined conditions. We propose to remove references to the superseded first edition (2000) of this standard in §§ 111.60-1, 111.60-2, 111.60-6, and 111.107-1. Because § 111.60-6 does not need to reference this test, we propose to delete § 111.60-2 and to reference the more recent edition 2.0 (2018) of this standard only in §§ 111.60-1 and 111.107-1(c). This more recent edition retains and updates the pre-existing categories of tests, adds a new category (category D) for testing at very low non-metallic volumes, and emphasizes that it applies to optical fibre cables as well as metallic conductor cables.

•
IEC 60529:2013—Degrees of protection provided by enclosures (IP Code), Edition 2.2, 2013-08.
This standard describes a system for classifying the degrees of protection provided by the enclosures of electrical equipment as well as the requirements

for these degrees of protection and tests to verify the requirements. We currently reference Edition 2.1 (2001) of this standard in §§ 110.15-1, 111.01-9, 113.10-7, 113.20-3, 113.25-11, 113.30-25, 113.37-10, 113.40-10, and 113.50-5. In these sections, we propose to reference the more recent edition 2.2 (2013) of this standard. Edition 2.2 (2013) is a minor technical update to the standard.

•
IEC 60533:2015—Electrical and electronic installations in ships—Electromagnetic compatibility—Ships with a metallic hull, Edition 3.0, 2015-08.
This standard specifies minimum requirements for emission, immunity, and performance criteria regarding electromagnetic compatibility (EMC) of electrical and electronic equipment for ships with metallic hull. We currently reference the second edition (1999) of this standard in § 113.05-7(a). We propose to reference the more recent edition 3.0 (2015) of this standard. This edition includes the following technical changes with respect to the previous edition:

○ The scope and title have been modified to limit the application of the standard to installations in ships with metallic hulls only;

○ The normative references have been updated;

○ Further explanation for in-situ testing has been given in section 5.1;

○ Cable routing requirements in Annex B have been amended; and

○ A new Annex C EMC test report has been added.

•
IEC 60947-2:2019—Low-voltage switchgear and controlgear—Part 2: Circuit-breakers, Edition 5.1, 2019-07.
This standard provides circuit-breaker construction and testing requirements. We currently reference the third edition (2003) of this standard in § 111.54-1(b). We propose to reference the more recent edition 5.1 (2019) of this standard. The 2019 edition of this standard contains numerous technical updates addressing technical advancements, including circuit-breaker testing, instantaneous trip circuit-breakers, and electromagnetic compatibility.

•
IEC 61363-1:1998—Electrical installations of ships and mobile and fixed offshore units—Part 1: Procedures for calculating short-circuit currents in three-phase a.c., first edition, 1998-02.
This proposed rule would make formatting changes to the standard's title for consistency with the titles of all other referenced IEC standards, but does not alter the edition currently incorporated by reference. We currently reference this 1998 edition in § 111.52-5. This proposed rule would move the standard to the new § 111.51-4(b) because we propose combining the requirements of subparts 111.51 and 111.52 into a single subpart 111.51 (Calculation of Short-Circuit Currents and Coordination of Overcurrent Protective Devices).

•
IEC 61439-6: 2012—Low-voltage switchgear and controlgear assemblies—Part 6: Busbar trunking systems (busways), Edition 1.0, 2012-05.
This standard states busbar service conditions, construction requirements, technical characteristics and verification requirements for low voltage busbar trunking systems. We propose to add it to the revised § 111.59-1 concerning general requirements for busways.

•
IEC 61660-1:1997—Short-circuit currents in d.c. auxiliary installations in power plants and substations—Part 1: Calculation of short-circuit currents, First Edition, 1997-06.
This standard describes a method for calculating short-circuit currents in DC auxiliary systems in power plants and substations. We propose to include it in the revised § 111.51-4(b) as an alternative for short-circuit analysis.

•
IEC 61892-7:2019—Mobile and fixed offshore units—Electrical installations—Part 7: Hazardous areas, Edition 4.0, 2019-04.
This standard contains provisions for hazardous areas classification and choice of electrical installation in hazardous areas in mobile and fixed offshore units, including pipelines, pumping or “pigging” stations, compressor stations and exposed location single buoy moorings, used in the offshore petroleum industry for drilling, processing, and for storage purposes. We currently reference Edition 2.0 (2007) of this standard in § 111.108-3(b). We propose to update the reference in § 111.108-3(b) to the more recent edition 4.0 (2019) and to insert new references to this standard in §§ 111.105-1, 111.105-3(b), 111.105-7, and 111.105-17(b). The standard has been completely rewritten. The Explosion Protection Level concept has been introduced as an alternative risk-based classification method and the requirements for installations in hazardous conditions reference IEC 60079-14 and other relevant standards, as appropriate. The incorporation of this standard into subpart 111.105 will provide an alternate standard for classifications for hazardous locations.

•
IEC 62271-100:2017—High-voltage switchgear and controlgear—Part 100: Alternating-current circuit-breakers, Edition 2.2, 2017-06.
This standard provides construction and testing requirements for circuit-breakers having voltages above 1000 V. We currently reference Edition 1.1 (2003) of this standard in § 111.54-1(c). We propose to reference the more recent edition 2.2 (2017) of this standard. There have been numerous technical updates to address technical advancements in switchgear. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
IEC-TR 60092-370:2009—Technical Report—Electrical installations in ships—Part 370: Guidance on the selection of cables for telecommunication and data transfer including radio-frequency cables, Edition 1.0, 2009-07.
This technical report gives guidance and basic recommendations for the selection and installation of shipboard and offshore unit cables intended for electrical systems used in both essential and non-essential analogue or digital signal communication, transmission, and control networks, including types suitable for high-frequency signals (
i.e.,
signals with a frequency of more than 10
5
Hertz). We propose to reference this new standard in § 111.60-1. This will align our requirements with those of recognized classification society rules and industry practice.

•
IEC/IEEE 80005-1:2019—Utility connections in port—Part 1: High voltage shore connection (HVSC) systems—General requirements, Edition 2.0, 2019-03.
This standard describes the design, installation, and testing of HVSC systems, on board the ship and on shore, to supply the ship with electrical power from shore. Ships may be required by state or local laws to connect to high voltage shore power (over 1000 V) rather than running their onboard generators. We propose in § 111.83-7 that these ships meet the requirements of this standard.

•
International Convention for the Safety of Life at Sea (SOLAS), Consolidated Text of the International Convention for the Safety of Life at Sea, 1974, and its Protocol of 1988: Article, Annexes and Certificates. (Incorporating all amendments in effect from 1 July 2014), 2014.
SOLAS provides requirements for vessel construction, arrangement, and management on international voyages. We reference SOLAS 2001 requirements in §§ 111.99-5, 112.15-1, and 113.25-6 and propose to incorporate the latest 2014 edition of SOLAS. While the applicable sections of SOLAS referenced in these requirements have not changed, for completeness we are incorporating the latest SOLAS amendments because industry is likely to use the more recent edition.

•

International Maritime Organization Resolution A.1023(26)—

Code for the Construction and Equipment of Mobile Offshore Drilling Units, 2009.

We propose nonsubstantive formatting change to the listing of this resolution in § 110-10-1(b). Chapter 6 of this resolution is referenced in § 111.108-3(b). The resolution provides requirements for machinery and electrical installations in hazardous areas of mobile offshore drilling units.

•
International Society of Automation (ISA) RP 12.6—Wiring Practices for Hazardous (Classified) Locations Instrumentation Part I: Intrinsic Safety, 1995.
We are proposing to delete this standard from reference in § 111.105-11. It has been withdrawn by ISA, is no longer supported by ISA, and is not available at
www.isa.org.
Instead, we propose to reference NFPA 70 and IEC 60092-502:1999 for the intrinsically safe system requirements in § 111.105-11.

•
ISO
25861
—Ships and marine technology—Navigation—Daylight signaling lamps, first edition, Dec, 1, 2007.
We are proposing to reference this standard in § 111.75-18 regarding daylight signaling lamps. This standard provides performance requirements for daylight signaling lamps pursuant to chapter V of SOLAS, 1974, as amended, and chapter 8 of the International Code for Safety for High-Speed Craft. The performance standards for daylight signaling lamps currently in § 111.75-18 are based on the international requirements in place in 1996. These requirements have been superseded by the requirements contained in ISO 25861.

•
Lloyd's Register Type Approval System-Test Specification Number 1, March 2019.
This specification details performance and environmental testing required for products used in marine applications. We currently reference the 2002 edition of this standard in § 113.05-7(a). We propose to reference the more recent 2019 edition. It has been updated several times to keep pace with changes in environmental testing.

•
National Electrical Manufacturers Association (NEMA) Standards Publication ICS 2-2000 (R2005)—Industrial Control and Systems Controllers, Contactors, and Overload Relays, Rated 600 Volts, 2000.
This edition is referenced in § 111.70-3. NEMA reaffirmed the edition without change in 2005. We propose to reference the reaffirmed date in the standard's title, which would result in no substantive changes.

•
NEMA Standards Publication ICS 2.3-1995—Instructions for the Handling, Installation, Operation, and Maintenance of Motor Control Centers Rated not More Than 600 Volts, 1995 (R2008).
This edition is referenced in § 111.70-3. NEMA reaffirmed the edition without change in 2008. We propose to reference the reaffirmed date in the standard's title, which would result in no substantive changes.

•
NEMA Standards Publication No. ICS 2.4-2003 (R2102)—NEMA and IEC Devices for Motor Service—a Guide for Understanding the Differences, 2003.
This edition is referenced in § 111.70-3. NEMA reaffirmed the edition without change in 2012. We propose to reference the reaffirmed date in the standard's title, which would result in no substantive changes.

•
NEMA Standards Publication No. ANSI/NEMA 250-2018—Enclosures for Electrical Equipment (1000 Volts Maximum), Edition 14, 2018.
This standard covers classification of enclosures for electrical equipment as well as the requirements for these enclosures and tests to demonstrate conformance with the requirements. We currently reference the 1997 edition of this standard in §§ 110.15-1, 111.01-9, 113.10-7, 113.20-3, 113.25-11(a), 113.30-25(e), 113.37-10(b), 113.40-10(b), and 113.50-5(g). We propose to reference the more recent 2014 edition in these sections. The 2014 edition added several new enclosure types as well as several minor construction details.

•
NEMA Standards Publication No. WC-3-1992—Rubber Insulated Wire and Cable for the Transmission and Distribution of Electrical Energy, Revision 1, Feb. 1994.
This is one of many options listed as a standard for allowable current-carrying capacity. We propose to delete it from § 111.60-13(c) because NEMA rescinded the standard.

•
ANSI/NEMA WC-70 ICEA S-95-658—Power Cables Rated 2000 V or Less for the Distribution of Electrical Energy, Feb. 23, 2009.
This standard applies to materials, constructions, and testing of 2000 V and less thermoplastic, cross-linked polyethylene, and cross-linked rubber insulated wires and cables which are used for the transmission and distribution of electrical energy for normal conditions of installation and service, either indoors, outdoors, aerial, underground, or submarine. We currently reference the 1999 edition of this standard, NEMA WC-70ICEA S-95-658, in § 111.60. We propose to reference the more recent 2009 edition with the updated naming convention. The 2009 standard contains updates based on advancements in technology including new cable jacket types and updated testing methods.

•
National Fire Protection Association (NFPA) 70—National Electrical Code, 2017 Edition.
This code is referenced in many sections of subchapter J and is the basis for electrical regulations worldwide. Currently, both the 2002 and 2014 editions of the code are incorporated by reference in §§ 111.05-33, 111.20-15, 111.50-3, 111.50-7(a), 111.50-9, 111.53-1(a), 111.54-1(a), 111.55-1(a), 111.59-1, 111.60-7, 111.60-13, 111.60-23, 111.81-1(d), 111.105-1, 111.105-3, 111.105-7(a), 111.105-11, 111.105-17(b), 111.106-3(b), 111.106-5(c), 111.107-1(b) and 111.108-3(b)(1) and (2). We propose to reference the 2017 edition in all the aforementioned sections where the NFPA 70 code is referenced. We also propose to include § 110.15-1 in the list of sections referencing NFPA 70 because NFPA 70 is currently used in the definition of “Special Division 1”. Substantive changes to the NFPA 70 articles between the previous editions include the following:

○ Article 240—This article on overcurrent protection raised the threshold for high voltage overcurrent protection from 600 V to 1000 V. Additionally, it addresses arc energy reduction of fuses rated at 1200A or higher.

○ Article 250.119—Section 250.119 details the identification requirements for equipment grounding conductors. The 2017 and 2002 editions are similar, but the 2017 edition contains greater specificity for specific installations and prohibits other cables to be covered in manner that could confuse them with equipment grounding conductors.

○ Article 250.122—Section 250.122 details requirements for the size of equipment grounding conductors. The content in the two editions is similar, but the 2017 edition adds requirements for multi-conductor cable, consideration of instantaneous-trip circuit breakers or motor short-circuit protectors, and greater specificity for flexible cord and fixture wire.

○ Article 250—This article on grounding conductors has been updated based on changes in technology and has added requirements for conductors in raceways and multiconductor cable.

○ Article 314—This article on outlet or junction boxes has several minor updates based on changes in technology or industry practices.

○ Article 368—This article on busways was reformatted and the threshold for high voltage busways was raised from 600 V to 1000 V. Additionally it provides more detailed wiring requirements.

○ Article 400—This article on flexible cords and cable provides several additional types of flexible cords as well as conductor sizes, but the allowable

ampacities for the existing types of flexible cords and cables have not changed. Additionally, it requires that the maximum operating temperature be added to the required markings.

○ Article 404—It has been clarified that this article on switches in <1000 V systems and several additional switch types have been added.

○ Article 430—This article on motors now raises the threshold for motors requiring additional protective measures from 600 V to 1000 V. Part X has been added to provide greater detail on adjustable-speed drive systems. Additionally a variety of minor technical updates made as well as referencing the latest standards.

○ Article 450—This article on transformers raised the transformer threshold for high voltage transformers from 600 V to 1000 V. Additionally minor editorial changes were made. For example, in several sections the word “sufficient” was replaced with “not less than” to ensure the intent was clear.

○ Article 504—Sections 504.10, 504.30, 504.50 and 504.60 on intrinsically safe system design are proposed to be added in § 111.105-11 because ISA RP 12.6 has been withdrawn by ISA. The requirements are similar and NFPA is the authoritative standard for electrical engineering design.

•
NFPA 77—Recommended Practice on Static Electricity, 2019 Edition.
This recommended practice applies to the identification, assessment, and control of static electricity for purposes of preventing fires and explosions. We currently reference the 2000 edition of this standard in § 111.105-27(b). We propose to reference the more recent, 2019 edition, which has been completely reorganized but the technical content is very similar. However, the 2019 editions contains changes regarding the characterization of combustible dust.

•
NFPA 99—Health Care Facilities Code, 2018.
This code provides information on health care facilities related to medical gas and vacuum systems, electrical systems, electrical equipment, and gas equipment. We currently reference the 2005 edition of this standard in § 111.105-37. We propose to reference the more recent 2018 edition. The 2018 standard contains extensive updates and is the authoritative reference for flammable anesthetics.

•
NFPA 496—Standard for Purged and Pressurized Enclosures for Electrical Equipment, 2017 Edition.
This standard applies to purging and pressurizing for electrical equipment in hazardous locations, electrical equipment containing sources of flammable vapors, control rooms or buildings in hazardous locations, and analyzer rooms containing sources of flammable vapors or gases and located in hazardous locations. We currently reference the 2003 edition of this standard in § 111.105-7, the 2008 edition is currently referenced in § 111.106-3(c), and the 2013 edition is currently referenced in § 111.108-3(d). We propose to update the reference to the more recent 2017 edition in §§ 111.105-7, 111.106-3(c), and 111.108-3(d). The standard was revised to ensure correlation with the 2011 edition of NFPA 70. The definitions of “energized” and “identified” are extracted from NFPA 70. Equipment is required to be identified for use in a classified area, and the requirements for determining the suitability of identified equipment have been clarified. NFPA 496 clarified the definitions of Type X, Type Y, and Type Z pressurizing to more clearly define their usage. NFPA 496 has been an industry standard for purged and pressurized enclosures since 1971. Further, the newer edition no longer includes unspecific language such as “near”, “close to”, and “significant portion.” Such terms cannot be quantified in the design or evaluation of an installation designed to the standard.

•
Naval Sea Systems Command (NAVSEA) DDS 300-2—A.C. Fault Current Calculations, 1988.
We propose to remove this standard from Subchapter J because it is no longer supported or available. This is one of four options for fault calculations in § 111.52-5. We propose to reorganize the requirements for short-circuit calculations for systems 1500 kilowatts or above in § 111.52-5 into new § 111.51-4. The other three options would be included in the new § 111.51-4.

•
MIL-HDBK-299(SH), 1991—Military Handbook Cable Comparison Handbook Data Pertaining to Electric Shipboard Cable Notice 1-1991.
This document provides basic information on, and listings of, shipboard cables and also provides guidance for their design, handling, installation, and maintenance. This current edition is referenced in § 111.60-3 regarding cable applications. We propose to delete this standard because we are also proposing to delete § 111.60-3, which we discuss in section VI.C of this preamble as being unnecessarily prescriptive.

•
UL 44—Standard for Safety Thermoset-Insulated Wire and Cable, 2018.
This standard specifies the requirements for single-conductor and multiple-conductor thermoset-insulated wires and cables rated 600 V, 1000 V, 2000 V, and 5000 V. We currently reference the fifteenth edition (1999) of this standard in § 111.60-11(c). We propose to reference the nineteenth edition (2018). The standard has been completely updated based on changes in technology and now addresses wires and cables up to 5000 V. The 2002 edition only went to 2000 V. Additionally, new wire types and maximum voltage ratings are addressed

•
UL 50—Standard for Safety Enclosures for Electrical Equipment, 2013.
This standard covers the non-environmental construction and performance requirements for enclosures to protect personnel against incidental contact with the enclosed equipment. We currently reference the eleventh edition (1995) of this standard in § 111.81-1(d). We propose to reference the more recent thirteenth edition (2013). The updated standard addresses the following additional items:

○ Addition of environmental Type ratings 3X, 3RX, and 3SX;

○ Sharp edges on electrical equipment;

○ Requirements for slot and tab fastenings;

○ Clarification of types of cast metal suitable for use as an enclosure;

○ Equipment door opening 90 degrees from the closed position;

○ Certification Requirement Decision for nonmetallic-sheathed cable clamps; and

○ Revision to requirement of cover and flange overlap for cabinets used as panelboards.

•
UL 62—Standard for Safety Flexible Cords and Cables, 2018.
This standard specifies the requirements for flexible cords, elevator cables, electric vehicle cables, and hoistway cables rated 600 V maximum. We currently reference the sixteenth edition (1997) of this standard in § 111.60-13(a). We propose to reference the more recent twentieth edition (2018). This standard has been updated based on advancements in technology to address new cable types, jacket types, and testing techniques. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
UL 83—Standard for Safety Thermoplastic-Insulated Wires and Cables, 2017.
This Standard specifies the requirements for 600 V, single-conductor, thermoplastic-insulated wires and cables. We currently reference the twelfth edition (1998) of this standard in § 111.60-11(c). We propose to reference the sixteenth edition (2017). The standard has been completely

updated based on changes in technology. For example, it now addresses many new types of wire, wire sizes, and updated testing requirements.

•
UL 484—Standard for Safety Room Air Conditioners, 2014.
This standard provides requirements for room air conditioners rated not more than 600 V AC. We currently reference the seventh edition (1993) of this standard in § 111.87-3(a). We propose to reference the more recent, ninth edition (2014). The standard has been updated to account for current technology and environmental testing. In addition, sections dealing with smart air conditioners and air conditioners using flammable refrigerants have been added. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
UL 489—Standard for Safety Molded-Case Circuit Breakers, Molded-Case Switches, and Circuit-Breaker Enclosures, 2016.
This standard provides requirements for molded-case circuit breakers, circuit breaker and ground-fault circuit-interrupters, fused circuit breakers, high-fault protectors, and high-fault modules. These circuit breakers are specifically intended to provide service entrance, feeder, and branch circuit protection. We currently reference the ninth edition (1996) of this standard in §§ 111.01-15(c) and 111.54-1(b). We propose to reference the thirteenth edition (2016). There have been numerous technical updates to the standard. The scope has been increased to address component testing, programmable components, electronic overprotection, and electromagnetic compatibility. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
UL 514A—Standard for Safety Metallic Outlet Boxes, 2013.
This standard provides requirements for metallic outlet boxes including those intended for marine applications. We currently reference the ninth edition (1996) of this standard in § 111.81-1(d). We propose to reference the more recent, eleventh edition (2013). UL 514A has been revised and updated to account for advancements outlet box construction. It has been an industry standard for metallic outlet boxes since 1928.

•
UL 514B—Standard for Safety Conduit, Tubing, and Cable Fittings, 2012.
This standard provides requirements for fittings for use with cable and conduit. We currently reference the fourth edition (1997) of this standard in § 111.81-1(d). We propose to reference the more recent, sixth edition (2012). UL 514B has been updated to account for advancements in conduit, tubing, and cable fitting construction, as well as testing techniques. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
UL 514C—Standard for Safety Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers, 2014.
This standard provides requirements for nonmetallic outlet boxes, conduit bodies, flush-device boxes, extension rings, and covers. We currently reference the second edition (1988) of this standard in § 111.81-1(d). We propose to reference the more recent, fourth edition (2014). UL 514C has been updated to align with advancements in nonmetallic outlet boxes and alignment with requirements in similar standards. To ensure we address the latest technologies and industry practices, we are proposing to incorporate the more recent edition of this standard.

•
UL 674—Standard for Safety: Electric Motors and Generators for Use in Hazardous (Classified) Locations, 2011.
This standard provides requirements for electric motors and generators or submersible and nonsubmersible sewage pumps and systems suitable for use in hazardous (classified) locations. We currently reference the fourth edition (2003) of this standard in § 111.106-3(b) and the fifth edition (2011) is referenced in § 111.108-3(b). We propose to reference the more recent, fifth edition (2011) in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This ensures consistent, up-to-date standards for electrical installations on all vessel and facility types.

•
UL 823—Electric Heaters for Use in Hazardous (Classified) Locations, 2006.
This standard provides requirements for electric heaters suitable for use in hazardous (classified) locations. We currently reference the ninth edition (2006) of this standard in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the ninth edition (2006) in § 111.105-7(a), as well. This ensures that standards are consistent for electrical installations on all vessel and facility types.

•
UL 844—Standard for Safety: Luminaires for Use in Hazardous (Classified) Locations, 2012.
This standard provides requirements for fixed and portable luminaires for installation and use in hazardous (classified) locations. We currently reference the twelfth edition (2006) of this standard in § 111.106-3(b) and the thirteenth edition (2012) is referenced in § 111.108-3(b). We propose to reference the more recent, thirteenth edition (2012), in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This latest edition includes the following minor technical revisions:

○ Revisions for test paint for spray booth luminaires;

○ Revisions for temperature tests at elevated ambient temperatures; and

○ Clarification of required number of as-received samples of polymeric enclosure materials.

•
UL 913—Standard for Safety: Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III, Division 1, Hazardous Locations, Eighth Edition, 2013.
This standard provides requirements for apparatus or parts of apparatus intended for installation in hazardous locations. We currently reference the sixth edition (2002) of this standard in § 111.105-7(a) and the seventh edition (2006) is referenced in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the more recent eighth edition (2013) in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). This latest edition includes the following technical revisions:

○ Revisions to reference the latest 2013 editions of UL 60079-0 and UL 60079-11;

○ Deletion of redundant references to applicable ordinary locations requirements;

○ Revisions to address the equivalent installation and use of Class I, Division 1 and Class II, Division 1 intrinsically safe and associated apparatus in Class I, Zone 0 and Zone 20 hazardous (classified) locations respectively; and

○ Revisions to dust-tight enclosures for Class II Intrinsically Safe Apparatus.

•
UL 1042—Standard for Safety Electric Baseboard Heating Equipment, 2009.
This standard provides requirements for portable and fixed electric baseboard heating equipment rated at 600 V or less. We currently reference the third edition (1994) of this standard in § 111.87-3. We propose to reference the more recent, fifth edition (2009). This latest edition includes the following technical revisions:

○ Revisions requiring portable heater power supply cords to meet UL 817.

○ Revisions requiring electric connections to meet established UL standards, UL 310, UL 486A-486B, UL 886C, UL 486E, or UL 1977.

○ Revisions to equipment grounding provisions.

○ Update to the leakage current test.

•
UL 1072—Standard for Safety Medium-Voltage Power Cables, 2006.
This standard provides requirements for

shielded and nonshielded medium-voltage power cables. We currently reference the third edition (2001) of this standard in § 111.60-1(a). We propose to reference the more recent fourth edition (2006). The fourth edition contains revised supplemental jacket thicknesses. Because supplemental jackets are only required for cables intended to be buried in the ground, this revision has no substantive impact on UL 1072 cables intended for use on vessels.

•
UL 1104—Standard for Marine Navigation Lights, Second Edition, 1998.
This standard provides construction and testing requirements for navigation lights. This standard is referenced in § 111.75-17(f). The only changes proposed to this standard are to align the naming convention in the regulatory text with that of other UL standards and to specifically cite paragraph (f).

•
UL 1203—Standard for Safety: Explosion-Proof and Dust-Ignition Proof Electrical Equipment for Use in Hazardous (Classified) Locations, 2013.
This standard covers explosion-proof and dust-ignition-proof electrical equipment for installation and use in hazardous locations. We currently reference the third edition (2000) of this standard in § 111.105-9 and the fourth edition (2006) in §§ 111.106-3(b) and 111.108-3(b). We propose to reference the more recent fifth edition (2013) in § 111.105-7(a) instead of § 111.105-9 due to editorial reformatting of §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The more recent edition has relatively minor technical clarifications with minimal substantive changes.

•
UL 1309—Standard for Safety Marine Shipboard Cables, 2017.
This standard provides requirements for distribution (power) cables, and control and signal cables, for installation aboard marine vessels, fixed and floating offshore petroleum facilities, and Marine Offshore Drilling Units (MODUs). We currently reference the first edition (1995) of this standard in §§ 111.60-1, 111.60-3, and 111.106-5(a). We propose to reference the more recent, third edition (2017) only in §§ 111.60-1 and 111.106-5(a), because we are proposing to delete § 111.60-3. The standard has received updates to its construction, performance, ratings, and markings requirements.

•
UL 1581—Standard for Safety Reference Standard for Electrical Wires, Cables, and Flexible Cords, 2001.
We propose to delete references to this standard in §§ 111.30-19, 111.60-2, and 111.60-6 because the referenced test in this standard, VW-1, has been moved to UL 2556.

•
UL 1598—Standard for Safety Luminaires, 2018.
This standard provides requirements for luminaires for use in nonhazardous locations that are intended for installation on branch circuits of 600 V nominal or less. We currently reference the first edition (2000) of this standard in § 111.75-20. We propose to reference the more recent fourth edition (2018), which has been extensively updated based on changes in technology and construction techniques. This edition includes added requirements for placement and construction of light-emitting diode (LED) luminaires as well as LED test methods. The standard also includes LED components and subassemblies, and other LED requirements.

•
UL 1598A—Standard for Safety Supplemental Requirements for Luminaires for Installation on Marine Vessels, First Edition (with revisions through Apr. 17, 2015), Dec. 4, 2000.
The First Edition, December 4, 2000, is currently incorporated by reference in § 111.75-20. We propose to incorporate the First Edition with revisions through April 17, 2015 in this section. UL 1598A provides additional requirements for luminaires meeting UL 1598 and intended for vessels to ensure these luminaires are suitable for marine and shipboard environments. The revisions to the First Edition include non-substantive updates necessary due to changes in to clauses of standards referenced within UL 1598A that occurred since publication of the First Edition.

•
UL 1604—Electrical Equipment for use in Class I and II, Division 2 and Class III Hazardous (Classified) Locations, 1994.
We propose to delete this standard from § 111.108-3(b) because UL withdrew it and it is no longer an active standard. This is one of many options in § 111.108-3(b) for standards on electrical equipment in hazardous locations.

•
UL 2021—Standard for Safety Fixed and Location-Dedicated Electric Room Heaters, 2015.
We propose to reference this standard in § 111.87-3(a). This standard provides requirements for electric air heaters. It will be an additional standard regulated entities may choose for electric air heaters. We have previously accepted it on a case-by-case basis as equivalent to the existing standards in § 111.87-3(a).

•
UL 2225—Standard for Safety: Cables and Cable-Fittings for use in Hazardous (Classified) Locations, 2013.
We currently reference the second edition (2005) of this standard in § 111.106-3(b) and the third edition (2011) of this standard in § 111.108-3(b). We propose to reference the more recent fourth edition (2013) in §§ 111.105-7(a), 111.106-3(b), and 111.108-3(b). The latest edition includes the addition of Type TC-ER-HL cable for use in Class I, Zone 1 as permitted by the 2014 National Electrical Code to the scope, editorial revisions, and error corrections sections of the standard. The incorporation of this edition into all three sections ensures consistent, up-to-date standards for electrical installations on all vessel and facility types.

•
UL 2556—Wire and Cable Test Methods, 2015.
This standard describes the apparatus, test methods, and formulas to be used in carrying out the tests and calculations required by wire and cable standards. The flame retardant test VW-1, formerly of UL 1581, has been moved to this standard and is now called FV-2/VW-1. We propose to replace the UL 1581 with UL 2556 in § 111.30-19(b).

•
UL 60079-18—Standard for Safety Explosive Atmospheres—Part 18: Equipment Protection by Encapsulation “m”, 2017.
We propose this standard as a replacement for the ANSI/ISA 60079-18, which was withdrawn. UL 60079-18 is not substantively different than ANSI/ISA

[Text truncated at 120,000 characters. The full text is on the page linked above.]

---

Source: Frix Law Library, https://www.frixlaw.com/law-library/documents/fr%3A2021-06699. Public record. Not legal advice.